Search Documents

By M. Leroux, J. A. Finch

"Sizing below 38 µm (400 mesh) is an increasing requirement in mill testing laboratories. The Cyclosizer is gaining wide acceptance in this role. A recent alternative is to use electro-formed sieves (micro-sieves), which are available with openings down to 5 µm. The advantage of micro-sieving is a cut size which is independent of mineral density, easier retention of the fi nest fraction and reduced purchase cost. A simple method of microsieving using an ultrasonic bath, which performs readily to 10 µm, is described.A systematic study of Cyclosizing and micro-sieving is reported for three samples; silica, copper oxide and a lead concentrate. Micro-sieving gave comparable results. Comparison with a standard sizing method, the Sedigraph 5000D, revealed misplaced material in each fraction by both methods. The range for micro-sieving was from 20% to 60% depending on the sieve and material; for the Cyclosizer it was a consistent 40-50% for all cones and all materials. The Cyclosizer can be sensitive to feed mass and particle size for dense materials. It is recommended that for minerals of specific gravity greater than 5, no more than 35 g of -38 µm be used.The disadvantage of micro-sieving is that it requires continuous operator attention and sieving time depends on sample mass. To fractionate 35 g-as used on the Cyclosizer and considered at reasonable mass for mill testing purposes-through 25-, 15- and 10-µm sieves requires about 80 minutes.IntroductionParticle size has a pronounced influence on mineral separation processes. Consequently, the measurement of particle size plays an important part in mill testing. By far the most common method is by screening. This, however, is usually limited to 38 µm (400 mesh) or occasionally 25 µm (500 mesh). Increasingly, mineral products are becoming finer than this limit and consequently finer sizing methods are required."

Jan 1, 1982

By Mônica Aline Magalhães Gurgel

Nas últimas décadas o setor siderúrgico vem desenvolvendo aços com maior valor tecnológico, surgindo assim várias classes, entre elas os aços avançados de alta resistência, onde encontra-se o aço bifásico ou “Dual Phase” (DP). Este aço é caracterizado por uma microestrutura ferrítica-martensítica, associada a uma matriz ferrítica com ilhas dispersas de martensita. Neste trabalho utilizou-se amostras de um aço baixo C e Mn, com micro adição de Nb e Mo, em desenvolvimento, onde se propôs uma avaliação da evolução microestrutural e propriedades mecânicas das amostras extraídas após a laminação a quente, a frio, seguida de recozimento intercrítico, em escala laboratorial, com auxílio de forno Mufla e um equipamento de análise termomecânica (TMA), resultando em taxas de aquecimento distintas, onde selecionou 7 temperaturas de encharque distintas e subsequente resfriamento com patamar isotérmico a 600°C por 20 minutos, onde observou-se que para esse ciclo a microestrutura com aspectos mais característicos de um DP se deu em tratamentos com temperatura de encharque entre 760 e 800°C.

Aug 17, 2017

By A. M. Garbers-Craig, T. Coetsee, T. M. Nemavhola

Accretions often form in furnaces when slag and charge materials attach to the refractory wall and build up over time. Accretion formation is usually unwanted because it reduces the working volume of the reactor and hinders material flow through the reactor. However, in some instances a thin, stable accretion layer may be desirable to protect the underlying refractory material. In order to prevent and/or manage accretion formation, it is important to understand the underlying principles of this phenomenon in the particular reactor. Excessive accretion formation hampered production at the Exxaro FerroAlloys ferrosilicon melting and atomization plant. This plant uses induction furnaces in which a 15% silicon-iron alloy is produced by batch smelting a mixture of ferrosilicon of 75%Si grade and low-carbon steel. The molten ferrosilicon alloy is then gas-atomized to a powdered product for use as a dense medium in mineral processing plants. The objective of this study was to investigate the effect of different impurity levels in the ferrosilicon feed material on the extent of accretion formation as well as the effect on the accretion properties, which influence the ease of accretion removal upon furnace shut-down. Refractory and accretion samples were collected after a furnace shut-down and characterized using X-ray diffraction and scanning electron microscopy–energy dispersive spectroscopy. It was concluded that the trace elements in the FeSi-75 feed material (Al, Ca, Mn) were mostly responsible for accretion formation, but that rust on the low-carbon steel and oxidation of the steel contributed to accretion attachment to the lining. The total contaminant content, calcium to aluminium ratio in the FeSi-75 feed material, and thereby the liquid to solids ratio in the accretion at temperature determine the strength of attachment as well as growth of the accretion.

Feb 2, 2021

By H Rossiter, C Simpson, J Market, P Jeanneau

Downhole Assay tools are a geophysical method to collect an instigated response from the material surrounding a drill hole and deliver a multielement proxy-assay. They were first tested in the Pilbara at the turn of this century, however since 2011 they have seen a more focused testing and implementation regime with multiple companies across multiple Pilbara mine sites. The increase in the volume of data has led to advances in the measurements and significant improvements to the efficiency of the calibration process. Pulsed Fast and Thermal Neutron Activation Analysis (PFTNA) downhole assay tools collect gamma photon spectra which are characteristic of elemental signatures. One of the key components of the technique is calibrating the spectral signatures to lab assays. Each tool is slightly different due to the organic nature of the crystal detector and therefore responds slightly differently. Environment and hole conditions as well as ore characteristics are among other external influencing factors. Thus, a unique calibration is required for each tool. In addition, not all elements are measured directly, but some are actually characterised by proxy, meaning that if the signal-to-noise ratio for an element is small, it may be easier to identify the mineral or geology in which that element is found and thus infer the concentration of the element. These proxies may differ for each site or geology type within a site. There is a large advantage to build a unique calibration per tool at each site rather than a universal one to be used across the whole province. This then delivers the accuracy and precision of measurements that mining companies require for modern operations. Early work with the tool required several thousand metres of calibration data and several weeks of analysis to build each calibration. This process has now been streamlined to significantly reduce the amount of data required and the analysis time to make it much easier to introduce new tools to a site with an existing model or to create new models. This paper details the calibration process, illustrating the increasing accuracy of the models as training data are acquired as well as the methods for transferring a calibration from one tool to another.

Nov 8, 2021

By George Langford

THE McIntyre mine is in the Pearl Lake section of the Porcupine gold area. The rocks are Keewatin lavas intruded by quartz porphyries and albitite dikes of Algoman age. Gold-bearing quartz veins are found in the Keewatin rocks near the porphyry stocks. The whole area has been highly compressed by forces acting along a N. 20°W. line. These forces folded the Keewatin rocks before the intrusion of the Algoman rocks, and later schisted both the Keewatin and Algoman rocks. Vein fractures were developed after the folding but before the development of the schist by the compres-sive forces being locally broken up into couples. These couples were set up by the differential resistance to deformation of porphyries and basalts, and also by the competency of the dacites and incompetency of the tuffs and fragmental rocks. During the important period of vein formation, two zones were developed-an inner productive zone in which the quartz veins are ankerite-bearing and an outer barren zone in which the quartz veins are calcite-bearing. The vein solutions originated in the same magma that supplied the albitite dikes.

Jan 1, 1938

By Adrian E. Scheidegger

"AbstractThe possibilities of deriving pertinent information about fractures in an oil pay from data obtained by core analysis are investigated. It is shown that it is possible to obtain an estimate of the fractured area per unit volume of the pay, and that the size of the fractures can be estimated if their shape is known. A suggestion of a routine procedure for the analysis of fractures is given.1.-IntroductionMany oil fields are producing essentially from cracks or fractures. Where this is the case, it is important to be able to obtain a knowledge of the size and distribution of those fractures in the oil pay. This knowledge has to be derived from the analysis of cores taken from the fields, as it is generally impossible to follow a fracture through the pay by direct means. The necessity of using statistical methods to extrapolate the meagre information obtained from the cores of the wells is therefore indicated.It is known that the fractures are much bigger than the diameter of the cores; thus, if they strike a core, the latter will generally fall into two pieces. The angle of the fracture with the vertical can be measured and, if oriented cores are taken, the exact position of the surface element representing the intersection of the fracture with the drill stem can be determined. Sometimes the edge of a fracture can be seen in a core. The number of •Cores that show such an edge can be noted. Of course, one has to be careful to distinguish between original fractures in the pay and fractures in the core caused by drilling operations. Only the former are relevant."

Jan 1, 1955

By John B. Goddard

Crystallization of ammonium paratungstate (APT) is frequently the last effective purification step in producing high-purity tungsten. However, crystallizer mother liquors are often several times higher in tungsten than predicted by the solubility of APT. The formation of heteropoly anions, particularly those containing phosphorus and silicon, is largely responsible. Solubility of tungsten in APT mother liquor can be linearly correlated with the concentration of these and other impurities. The problem can be overcome by direct treatment of the crystallizer feed solution with alum. By appropriate treatment, the aluminum hydroxide flocculates and is easily filtered, resulting in a purified low-aluminum crystallizer feed from which high APT yields can be attained.

Jan 1, 1984

The objectives of mining grade control are presented and examples of the techniques used in various open pit and underground mines are used to define the attributes of good grade control. Reasons are discussed for the success of various improved practices. The progressive development of grade control is presented and the balance between quantitative and qualitative data is analysed. The skills and resources required for grade control on mine sites that are using best practice are also presented. A number of problems in grade control have been solved recently however there are still issues that need to be addressed. Examination of the grade control process frequently stops after sample quality has been examined. There is much more beyond this that can now be optimised using conditional simulation models. Other future directions of mining grade control are also suggested. An extensive bibliography of published papers on grade control is included that will be maintained and updated on a website.

Jan 1, 2000

By CHARLES M. SCHWAB

THE ENGINEERS have placed this great country of ours in a preeminent position with everything pertaining to manufacture, metallurgy, and the kindred arts. We are second to none in the world. We have a country which, another speaker has said, God has endowed with such riches in coal and natural resources as no other country in the world. But rich as these are, there is one thing greater; the sturdy character, energy, and integrity of its people, which will make these great resources an influence in the world's developments. Great as are these resources and the energy and integrity of our people, there is one problem of our .engineering, which I term human engineering, that is of far more importance than the creation of machines and methods, with which you have been so successful in the past. Of what value is the skillfully devised machinery, the complex process, unless manned and operated by people whose heart and soul are in sympathy with the work they are doing and who have before them the giving of a complete day's work for a day's pay?

Jan 1, 1920

Gravity gold recovery has been practiced for thousands of years, making it one of the oldest forms of mineral processing. Gold is 19 times heavier than water although the barren rock is generally only 2.7 times heavier. Any potential gold ore needs to be characterised to assess its amenability to a gravity recoverable gold (GRG) process based on well planned and executed test work. Scale up considerations need to be considered in designing a gravity circuit. The economic impact of a gravity circuit should be justified based on the installed cost and likely benefits. Maximising gravity gold recovery results in a faster cash flow, lower operating cost per ounce and higher overall gold recoveries compared to the several weeks required to recover gold adsorbed onto carbon. The advent of centrifugal concentrators such as the Knelson and Falcon, coupled with intensive leaching of concentrates (ILR), has revolutionised gravity gold circuit designs. Considerations associated with the sizing of the centrifugal machines and the percentage of the circulating load (bleed) that should be processed is discussed in this paper. The trends with gravity circuit layout, engineering, as well as optimum dumping cycles, are important areas which require close consideration. Key aspects of these are presented in this paper. There are a number of circuit configurations to be considered, including the integration of different gravity concentrators. Other gravity process design considerations such as fewer modules, the effect of equipment size and enhancement of process efficiency using preconcentration, together with factors that affect OPEX and CAPEX are addressed. Practical considerations of maintenance, security from theft, minimisation of risk and water balance considerations are discussed using different equipment and circuit configurations. The trend towards using gravity recovery in flotation plants is also reviewed. A number of examples are cited and good design aspects highlighted.

Aug 1, 2010

By P. S. Rao

In 1951, Tata Steel became the pioneer in Asia by setting up its first ever washery in West Bokaro Colliery. The first beneficiation plant used to produce clean coal of 19% ash with chance cone. Feed size of chance washers were -75 mm to +6 mm. The fine coal (-6 mm) were used directly. With change in technology,in 1986,chance cones were replaced by DM cyclones and coal was washed in two circuits. In the coarse circuit -13 mm to +0.5 mm coal was washed in two stages while the fine coal of -0.5 mm was treated in froth floatation cell. With further improvement in the process the higher ash raw coal was feed to produce clean coal of 13% ash. In 1998, DSM cyclones were replaced by scrolled Evolute design cyclone which has Ep of 0.020 to 0.025 ranges resulting in increase efficiency of separation. With the increase in demand of clean coal, lower seam proportion has increased in raw coal production. The washability studies of individual seams indicated large difference in the seam characteristics in terms of washability and specific gravity cut points of the individual seams. So washing all seams together had resulted in frequent change in the character of coal and warrants frequent changes in the operating parameters of the plant in which the separating efficiency comes down and ultimately resulted in yield loss initially. With increase in knowledge and experience in coal washing the solution to this problem was achieved by adopting, seam-wise washing which is enabling process engineers by keeping set point for longer periods there by to enhance the separation efficiency. Keywords: coal processing, froth floatation, steam washing

Sep 1, 2012

By A. B. Hooker, L. C. IlsLey

"The last previous Bureau of Mines publication relative to details of permissible electric mine lamps is Bulletin 332, which describes 16 lamps approved prior to May 1930. Some of the lamps have become obsolete through the development of improved models which, with several new types, make it desirable to supplement the Bureau's published data relative to permissible electric mine lamps.In the following descriptions, lamps approved since May 1930 and prior to July 1, 1935, are placed in the three following groups: (1) Electric cap lamps, (2) electric hand lamps, and (3) lamps for miscellaneous applications,ELECTRIC CAP LAMPS APPROVED UNDER SCHEDULE 6B1. Edison model J lamp, approval no. 24. - The features that distinguish this lamp from earlier models of Edison electric cap lamps are:(a) The battery consists of two F-2 cells of square cross section and about 1-1/4 inches higher than M-14 cells in the model H lamp, making the battery narrower and higher than any of the earlier models of Edison cap lamps.(b) The cells are insulated from each other and the Monel-metal casing by enclosure in vulcanized-rubber baglike enclosures. Both cell terminals are insulated from the cell jar.(c) The battery is equipped with rubber-tube Bunsen-valve-type gas vents.(d) The battery casing is secured by a new-type magnetic lock.(e.) The battery and cover terminal clips have been redesigned to give a wiping contact."

Jun 1, 1936

By Hun-Joon Sohn

Chemical metathesis and electrochemical reductive conversion of chalcopyrite in the presence of cupric ions were studied in sulfuric acid solutions for temperatures up to 90°C. The process results in the displacement of iron in the chalcopyrite lattice by copper ions with rejection of ferrous ions to the aqueous phase. The rate of reaction was found to be very slow, requiring subsieve-sized particles for extensive reaction to occur. The reaction was insensitive to copper ion concentration. Stirred ball milling of chalcopyrite introduces lattice strain. The reaction rate with strained particles was markedly higher than with annealed chalcopyrite. The reaction rate was found to be diffusion-limited, showing two distinct reaction stages corresponding to the formation of CuS (covellite) followed by Cu1.8S (digenite). The experimental activation energy for the first stage was 102 J (24.4 kcal) and the second stage 123 3 (29.4 -kcal) per mole. The rate-controlling process is diffusion of lattice ions, probably iron. The enhanced rate after milling is attributed to a recrystallization process which provides new paths for diffusion along dislocations and grain boundaries.

Jan 1, 1984

By L. W. Casteel, E. A. Jones

MINING the lead deposits of Southeast east Missouri has reached a high stage of technical development dictated by the scattered occurrences of low-grade ore through favorable horizons in the Bonne Terre formation. The rock-breaking, handling, and related practices described here have evolved as the best way of mining these particular deposits. These methods are applied in the production of about 19,000 tons of lead ore per operating day from four mines in Southeast Missouri. Development drilling Drifts 10 ft wide and either 8 or 9 ft high are driven in this district on contract. Miners are guaranteed standard wages plus a bonus on the footage advanced, if earned. Labor, fuse, caps, wire, and dynamite used are charged against the contract. Normally the cycle of operations in drifting is performed by a two-man crew, a motor operator and a shovel operator who first load out the rock broken by the preceding shift. The drift crew then sets up two vertical column and mounts the drills. Cleveland HC-10's are used which have a steel lug integral with the cylinder for connection with the air feed. All drilling in drifts is wet. Air pressure is 85 to 100 lb at the face. From 28 to 32 holes are drilled per swing in a pyramid cut. Cut holes

Jan 1, 1947

By Marlon José Zanotto

O objetivo deste trabalho é comparar o uso da liga~mãe Al-5Ti-1B e dos sais de fluortitanato de potássio (K2TiF6) e fluorborato de potássio (KBF4) no refino de uma liga de alumínio de pureza comercial. Os resultados demostram a eficiência da liga-mãe no refino de grão quando adicionada em quantidades acima de 0,6% em peso. No entanto, para o sal de boro, não houve refino de grão na mesma quantidade e no dobro da porcentagem. Já para o sal de titânio ocorreu refino de grão, provavelmente devido à presença de boro residual no alumínio puro comercial.

Aug 17, 2017

By G. W. Jones

In a previous report results were given and a method outlined whereby from a knowledge of the composition of the natural gas and of the inflammability limits of the individual constituents composing the natural gas, the limits of inflammability of natural gas and air mixtures could be closely calculated. This method is based on the application of Le Chatelier's law as modified by Coward, Carpenter and Payman, to apply to a mixture of any number of combustible gases. This law must not be used indiscriminately, because many exceptions have been found. For example, when ethylene, acetylene, hydrogen sulphide, or chlorinated hydrocarbons are present the law may not hold. For a discussion of the rally exceptions which have been found, reference should be made to a report by Coward and Jones. Before this method can be used the inflammable limits of the individual constituents must be known. Also, the composition of the complex combustible mixture, and representative mixtures besides, must be tested both experimentally and by calculation to prove whether Le Chatelier's law may be applied.

Jan 1, 1933

By Abhijit Saha

"The stone columns improve the performance of foundations on soft and loose soil due to the ability of composite ground to sustain increased structural loads under reduced settlements. The interaction between the two basic elements: the ambient subsoil and installed column, present a complexity of behaviour, both in terms of applied stresses and resulting strains. Moreover, as the same is provided in-group in a regular array beneath foundations, the performance of an individual column is likely to be influenced by the presence of neighbouring columns. The present paper addresses this very issue. Analysis of reported field hydro-test data of large diameter oil storage tanks in soft ground in reference to some existing theories led to the development of the stone-column ‘group efficiency factor’. In order that such factor is of general use, it was felt necessary to examine the applicability of the factor to different sizes of groups under varied subsoil conditions. With this in view, some model test results reported in literature of single and group of columns have been analysed and in the process an explicit relationship regarding the stone-column ‘groupeffect’ could be established.INTRODUCTIONThe field application of the stone column technology has gained momentum than the intricate design methodology due to its simplicity in installation and intuitive performance. The ground improvement is due to the complex interaction within the ‘unit-cell’ comprised of the installed column in ambient ground under sustained vertical stress; in association with the interdependence of problem geometry and material properties of the two different soils-one 'native' and the other 'back-filled'. The beneficial effects are increased load capacity, reduction in total and differential settlements, minimization of post construction settlements effected by accelerating consolidation, reduced risk of soil liquefaction, aiding in improvement of slope stability of embankments and natural slopes and effecting changes in the dynamic response. The ‘unit-cell’ concept of a tributary soil cylinder encapsulating an installed column with some reasonable assumptions and boundary conditions (Aboshi et al, 1979; Balaam & Booker, 1981; Van Impe & De Beer, 1983; Priebe, 1976; Saha & De, 1994; Saha; 2005, 2006, 2007, 2011, Saha & Das; 2007) deals with the load-settlement behaviour of the composite system. The present investigation is based on published field data from literature & validated with experimental study reported in literature. The study addresses the effect of group interaction of stone columns beneath a large area loading on ground settlement. The hydrotest load-settlement data of 12 large diameter oil storage tanks founded on stone column reinforced soil at Haldia1 and Kandla2 refinery sites in India; reported by Som (1997), has been analysed to quantify the group efficiency. The results as obtained are compared with experimental study on 2, 3 and 4 stone column groups at different spacing-diameter ratios in soft clay3 reported by Rao et al (1997) to validate the above analysis. A unique relationship between the column spacing and group efficiency has been obtained."

Jan 1, 2015

By G. E. Pellissier, C. W. Mason

Tin has long been cited as offering a classic example of polymorphism, second in repute only to the allotropy of sulphul.. The notorious "tin disease," which Cohenl has studied so exhaustively in terms of the enantiotropic transformation of tetragonal white P tin to cubic gray a tin, has apparently encouraged the expectation that one or more additional polymorphic modifications might exist. The search for confirnmntion of this idea has, as might be anticipated, led to the accumulation of a body of miscellaneous evidence, much of which would probably never have been sought, or taken seriously even by its discoverers, but fur previous assumptions. The ball apparently was started rolling iii 1880 by Trechmann,2 who reported a new modification of tin (7 tin), which was brittle and found in "hard head," a highly arsenical, slaggy material produced in a certain stage of tin smelting. A mixture of two kinds of crystals was obtained from a Cornish tin furnace, and those thought to be 7 tin were studied crystallographically. The results indicated that these crystals were rhombic and of different density from the tetragonal tin prepared electrolytically by Miller. Their analysis was given as 98.7 per cent Sn, 1.3 per cent Fe, and traces of As, Sb, Bi and S. In 1881 von Foullon4 obtained similar crystals from a Bohemian tin furnace. Headden5 examined crystals similar to those of Trechmann and von Foullon and reported them to be monoclinic, but of analysis corresponding to stannous sulphide. Later, Stevanovic,~ by goniometric measurements, proved that these crystals of SnS were really rhombic. Groth7 pictures and describes both "rhombic tin" (Fig. 9, vol. 1) ant1 stannous sulphide (Fig. 84, vol. 1); their faces and angles correspond within the accuracy of measurement. Spencers in 1921 examined the above evidence critically; lie lound similar crystals from Cornish tin furnaces, proved them to be SnS, and even was able to analyze some of Trechmann's original specimens, finding high sulphur content. (Apparently Trechmann's analysis had been based on :L second lot of crystals, not described crystallographically.)

Jan 1, 1939

By G. E. Pellissier, C. W. Mason

Tin has long been cited as offering a classic example of polymorphism, second in repute only to the allotropy of sulphul.. The notorious "tin disease," which Cohenl has studied so exhaustively in terms of the enantiotropic transformation of tetragonal white P tin to cubic gray a tin, has apparently encouraged the expectation that one or more additional polymorphic modifications might exist. The search for confirnmntion of this idea has, as might be anticipated, led to the accumulation of a body of miscellaneous evidence, much of which would probably never have been sought, or taken seriously even by its discoverers, but fur previous assumptions. The ball apparently was started rolling iii 1880 by Trechmann,2 who reported a new modification of tin (7 tin), which was brittle and found in "hard head," a highly arsenical, slaggy material produced in a certain stage of tin smelting. A mixture of two kinds of crystals was obtained from a Cornish tin furnace, and those thought to be 7 tin were studied crystallographically. The results indicated that these crystals were rhombic and of different density from the tetragonal tin prepared electrolytically by Miller. Their analysis was given as 98.7 per cent Sn, 1.3 per cent Fe, and traces of As, Sb, Bi and S. In 1881 von Foullon4 obtained similar crystals from a Bohemian tin furnace. Headden5 examined crystals similar to those of Trechmann and von Foullon and reported them to be monoclinic, but of analysis corresponding to stannous sulphide. Later, Stevanovic,~ by goniometric measurements, proved that these crystals of SnS were really rhombic. Groth7 pictures and describes both "rhombic tin" (Fig. 9, vol. 1) ant1 stannous sulphide (Fig. 84, vol. 1); their faces and angles correspond within the accuracy of measurement. Spencers in 1921 examined the above evidence critically; lie lound similar crystals from Cornish tin furnaces, proved them to be SnS, and even was able to analyze some of Trechmann's original specimens, finding high sulphur content. (Apparently Trechmann's analysis had been based on :L second lot of crystals, not described crystallographically.)

Jan 1, 1939

By Etiene Pereira de Andrade

Este trabalho avaliou a influência da deformação na formação de martensita e consequente resistência à corrosão do aço inoxidável austenítico AISI 304. O aço foi deformado em cisalhamento de 10%, 25%, 30%, 50% e 55% de deformação efetiva e em seguida mergulhado em solução contendo água do mar natural e artificial. As amostras imersas em solução de água do mar artificial exibiram aumento da massa enquanto as mergulhadas em água natural, redução. Esses resultados podem ser associados com a aderência inicial e estável de íons metálicos advindos dos cloretos, à superfície do material mergulhado em água do mar artificial.

Aug 17, 2017