Search Documents

By I. Ince, S. Kahraman

Preparation of suitable core specimens for physico-mechanical testing s not always possible, particularly for soft and clay-bearing rocks. Although several indirect test methods have been proposed to predict the properties of rocks, specimen preparation from soft rocks for some indirect tests is still difficult. For such cases, the needle penetration test has been developed. In this paper we present a study on the predictability of the physico-mechanical properties of pyroclastic rocks from the needle penetration index (NPI). The NPI, uniaxial compressive strength (UCS), Brazilian tensile strength (BTS), density, and porosity tests were performed in the laboratory on specimens from ten different locations in Turkey. Correlations were established between the NPI values and the physico-mechanical properties. Strong correlations were observed between NPI and both UCS and BTS. General correlations were found between NPI and both density and porosity.

Sep 6, 2023

By D. Vega, P. R. Brito-Parada

"Small diameter (10 mm) hydrocyclones have been applied successfully for the separation of particle suspensions in the micron size range. These hydrocyclones are attractive because they show a bypass fraction larger that the water recovery, resulting in a high particle recovery to the underflow as well as low water recovery. However, this is a disadvantage when the purpose of the hydrocyclone is classification because of the large amount of fine particles that are misplaced in the underflow. The aim of this study is to explore, experimentally and computationally, the influence of design parameters on the classification process. In this work, a full factorial experimental design was defined to carry out comprehensive experimental tests using glass beads (0-20 µm) as the particulate system. We show that the dimensions of spigot and vortex finder diameter can be effectively manipulated to change the separation performance of the system and the energy consumption. A CFD model was developed that is able to predict particle size distribution. The numerical results for the partition curves showed very good agreement with the experimental data. INTRODUCTION Small diameter hydrocyclones are a very attractive separation technology for fine particle suspensions. Since the hydrocyclone diameter is directly proportional to the cutsize that can be achieved, 10mm hydrocyclones have been shown to be very effective in collecting particles in the micron-size range. In addition, while in large hydrocyclones the bypass, i.e. the fraction of particles that report to the underflow without classification, is similar to the water recovery, in 10mm hydrocyclones the bypass fraction is considerably larger than the water recovery. Its high particle recovery and low water recovery makes small hydrocyclones ideal for ultrafine particle classification and dewatering applications in mineral processing. The separation of mineral suspensions achieved using small hydrocyclones has been the focus of various studies. Pasquier and Cilliers (2000) derived a general classification model from experimental data of fine silica concentration in 10mm hydrocyclones; the model was able to describe the fish-hook partition curve. The effect of operating conditions has also received some attention in the literature. Cilliers et al. (2004) showed that an increase in temperature positively effects the recovery of fine silica particles in small hydrocyclones, by increasing the bypass and decreasing the cutsize. Neese et al. (2015) showed that the cutsize in 10mm hydrocyclones can be further decreased by operating at higher pressure, which also trebled the throughput."

Jan 1, 2018

By S. W. Cavender

The analysis of the results of metallurgical experiments is often complicated by experimental errors and uncertainty, the complexity of the system being studied, and the confusion of correlation with causation. Consequently, comparative statistics are used to determine if a difference exists between the outcomes of tests, an estimate of this difference, and the precision of the estimate. This paper reviews the use of significance tests and confidence intervals for the comparison of results from two tests, the use of reference distributions, and blocking and randomization techniques to reduce unavoidable sources of variability. These techniques are demonstrated using plant and laboratory data.

Jan 1, 1993

By Bin Xu, Qian Li, Yong-bin Yang, Xiao-liang Liu, Tao Jiang, Yan Zhang

Some high sulfur and arsenic-bearing gold concentrate has a gold leaching rate less than 80% by oxidation roasting-pickling-cyanidation process. The characteristics and intensification of gold leaching were studied systemically. By combining chemical composition and phase analysis, the low gold leaching rate was found to lie in the capsulation of gold by iron-containing phases including iron oxides, arsenopyrite and pyrite. 96.66% of gold in the industrial leaching residue was capsulated and 95.88% of the capsulated turned out to be in the iron-containing phases. The results of laboratory pickling-cyanidation experiments on the calcine and industrial leaching residue presented further demonstration for the fact that gold capsulated in the iron-containing phases was hard to be leached. However, the gold cyanide leaching rate of calcine could be raised over 95% by a reduction roasting-pickling pretreatment which played such a significant role in exposing the capsulated gold that gold leaching was intensified remarkably.

Jan 1, 2015

By NEWTON B. KNOX

THE Guianas region is a geological unit, consisting of the northern lobe of the Brazilian Shield, but political accident and the fact that rivers act as the principal means of transportation have divided the region between five separate sovereignties. Brazilian and Venezuelan Guiana have already been considered. The French, Dutch, and British colonies consist of a coastal plain some fifty miles wide, which, together with the lower reaches of the principal rivers, support the greater part of the population. Inland from this tidewater region is a wide area of low, forest-covered hills, under-lain by gneisses, schists, granites, and pegmatites of the Shield. As in Venezuelan Guiana, these rocks are overlain by a thick series of horizontal continental sediments intruded by moderately basic magmas. Gold, bauxite and diamonds have been the principal products of the colonies. The first metal is quite widespread in the hill country. The quartz mines are small, though occasionally rich; probably the greater number of veins remain undiscovered because of the thick mantle of decomposition product that covers the schists and gneisses. The greater proportion of the gold, therefore, is derived from placers which are exploited in all three colonies. Some geologists claim that they occur in two belts parallel to the coast; whether this feature has its origin in the location of the primary mineralization or in the gradients of the rivers is not clear. In some instances the river gravels grade into auriferous laterite. The laterites are well developed in the Guianas and represent the weathering products of the more basic rocks.

Jan 1, 1946

By L. Naude, J. Cloete, S. Engelbrecht

The results of an investigation evaluating whether an industrial plant, currently operating using sodium isobutyl xanthate (SIBX) as primary collector for sulphide minerals (mainly chalocopyrite), could adapt to operate using an alternate primary thiol collector without compromising plant and metallurgical performance. Initial laboratory scale flotation tests identified commercial dithiophosphate (DTP)-based and thionocarbamate (TC)-based collectors, that when blended, showed potential to replace the incumbent SIBX primary PGM collector. Industrial plant trail results show that there was no deterioration in recovery of 4E PGMs, even at a lower concentrate grade when operating the plant on the identified (DTP + TC)-based collector blend compared to SIBX. The effect on Cr2O3 content in the final concentrate was also found to be negligible. The (DTP + DTC)-based collector blend also showed promise in terms of plant adaptability in accommodating a new primary specialty collector blend. These observations highlighted the potential of replacing xanthate primary collectors with alternate thiol collector blends for PGM flotation. Keywords: PGM, xanthate replacement, specialty collector, sodium iso-butyl xanthate (SIBX), dithiophosphates (DTP), dithiocarbamates (DTC)

Jan 1, 2020

By E. von Maltitz

IN his highly interesting paper on "Piping and Segregation in Steel Ingots,"1 Prof. Howe emphasizes the effect of successive phases of internal pressure in the ingot in the evolution of gas, and the consequent formation of blow-holes. From his statements in other places, it may be inferred that he does not here intend to ignore the other variable factor, temperature, but rather to discuss this one more particularly. At all events, it is my purpose not to engage in controversy with Prof. Howe, but rather to contribute, towards the complete elucidation of this important subject which we all desire, my own views and experience. If, in doing so, I specially emphasize other factors than pressure, I need not be understood as denying what I do not think it necessary to discuss fully. Nor, in presenting my own original conclusions, need I be understood as claiming to be the first who ever reached or announced them. Many things are asserted or suggested upon inconclusive evidence; and to confirm such tentative propositions may be as valuable a service as to overthrow them. In the following passage, Prof. Howe adduces analogies, based upon the behavior of charcoal and of water, respectively, which seem to me questionable "In general, the. solvent power falls as the pressure falls ; and in general it rises as the temperature falls. Thus, to heat a solid, for instance charcoal, may expel part of its dissolved gas ; and a tumbler of water drawn cold from the faucet gradually evolves gas, as it stands and warms up on the sideboard." (p. 238.) Charcoal is a solid body, which has the property not only of absorbing gases in large quantities, but also of expelling the thus absorbed gases upon heating. A comparison between charcoal and iron as to the absorption of gases is scientifically not possible ; the gas-content of charcoal is partly due to the

Sep 1, 1907

By J. Lindström, J. Hamuyuni, M. Lundström, J. Aromaa

"The rising demand for metals today, coupled with the scarcity of primary sources for raw materials threatens both technological advancements and industrial manufacturing. In order to meet the demand, metals and other resources trapped in waste streams, have to be harnessed. This philosophy supports circular economy, where metals and other resources are kept in a closed loop. The pickling acid recovery system of most stainless steel production is one such example where the dissolved metals such as iron, nickel and chromium are currently not completely recovered due to the limitations of the current technologies. The aim of this study was to assess the available metals recovery methods from extremely concentrated acids. The main aim is to simultaneously recover metals and keep sulphuric acid reusable in acid circulation process. From the available literature, the most promising methods were chosen for laboratory experiments. Based on experimental work, the results and observations of electrodeposition, solvent extraction, and freeze crystallization are provided. KEYWORDS Pickling acid, metal recovery, solvent extraction, cathodic polarization, Freeze crystallization. INTRODUCTION Pickling in stainless steel production is an essential surface treatment process (Regel-Rosocka, M. (2010); Agrawal and Sahu, 2009). It is applied for removing surface films such as oxides and chromium-depleted layers to improve the corrosion resistance and surface finish of steel (Regel-Rosocka, 2010). Whilst the process greatly improves the surface finish of the stainless steel, it generates large amount of used acid, containing dissolved metals including chromium, iron, and nickel (Agrawal and Sahu, 2009). Recovery of acid is common practice for most steel producing industries (Nyman and Koivunen, 1986). In this work, acid regeneration process is investigated so as to simultaneously reusing sulfuric acid and recovering the dissolved metals. Recovery of valuable metals even in very small amounts would also bring additional revenue to the steel production industry. At a time when metal production has also been challenged by lack of natural resources for raw materials, secondary sources for metals such as the acid pickling process therefore, have greater potential as supplements. From earlier studies, electrodeposition (Giovanardi and Orlando, 2011; Kuznetsov et al., 200; Rögener et al., 2012; Surviliene et al., 2006), solvent extraction (Alguacil and López 1996; Haghshenas et al., 2009; Kesieme et al., 2013) and freeze crystallization (Beyer et al.,2003; Hasan et al.,2017; Van der Ham et al., 1999) are some of the most established potential methods. Earlier studies have also shown that simultaneous recovery of acid and metals would require combination of different methods. This is primarily due to the nature of very stable metal containing complex compounds formed during pickling. These complexes must be broken down to free the metals for further recovery processes."

Jan 1, 2018

By R A. Burwash

In the Yellowknife geologic province, 2,600-million-year-old granites are cut by three sets of diabase or gabbro dyke : (1) large dykes striking 70°E to E-W, (2) rare dykes striking N-S to 30°E and (3) an abundant swarm striking N 10°-300W. Preliminary potassium-argon dating has been carried out on whole-rock samples of the chilled margins and coarse centers of the dykes, and on mineral separates from the dykes and contact aureoles. Data from seventeen dated samples suggest that the dyke sets were intruded during three periods of basaltic magmatism -2,200, 1,500 and 1000 million years ago. The two earlier periods closely follow the time of emplacement of granites in the Yellowknife and Churchill geologic provinces. The latest diabase dykes occurring in the Yellowknife province are temporally related to a widespread basaltic magmatism, for which the term Keweenawan is not appropriate. D DRING the past ten years, methods of physical age determination have been widely applied to date the time of intrusion or metamorphism of Precambrian rock

Jan 1, 1963

By C. R. Fettke

In 1914, the officials of the Brundred Oil Corpn., faced with the problem of introducing new methods to increase production in the old and nearly depleted pools of Venango County, became interested in the Smith-Dunn (Marietta) process which was at that time being tried out in southeastern Ohio and which was already yielding very encouraging results. A license to use the process in Pennsylvania was secured from the owners of the patents. These patents were later declared invalid. The method was first used in Pennsylvania on a property consisting of about 434 acres, of which 300 are productive, at Hamilton Corners, 15 miles northwest of Oil City, in Cherry Tree and Oakland Townships, Venango County. The producing horizon is the First Sand of the Venango Group. A small oil pool was opened up in this vicinity in 1904. By July, 1916, when the compressed air was first introduced to restore pressure, the production had dropped to a point where it was no longer possible to continue profitable operation. From that time until March, 1927, over 100,000 bbl. of oil have been recovered from the tract. The property is being operated at present by the Brundred Oil Corpn. and LUX. The 1926 production, amounting to 10,650 bbl., was only 400 bbl. short of the maximum reached during any year of the 10-year period that the process has been in operation. Inasmuch as the Hamilton Corners pool is the first one in Pennsylvania in which the Marietta process was tried out, and the one in which it has been longest in continuous operation, considerable interest attaches to the results obtained. Through the courtesy of H. D. Brown and W. J. Brundred, officials of the Brundred Oil Corpn., all their data on this operation were made available to the writer in connection with an investigation of rejuvenation methods in the State for the Pennsylvania Geological Survey. Stratigraphic Position of the Producing Sand The producing sand at Hamilton Corners is encountered at depths of from 364 to 560 ft., depending on the location of the well and the topog-

Jan 1, 1928

By Sunil S. Gandhi

"Uranium occurrences are widely distributed in tuffaceous-argillaceous beds and abundant rhyolitic volcanic rocks of the upper Aillik group, which is more than 3 km thick and over 125 km by 40 km in areal extent. They include partially developed Kitts and Michelin deposits, containing 1560 and 7366 t U respectively.Uranium occurs mainly as disseminated fine pitchblende grains in beds and lenticular stratabound zones, and rarely as coarse pitchblende aggregates and thin veinlets. The Kitts deposit and ten other occurrences are in the argillaceous-tuffaceous beds within a steeply dipping stratigraphic zone, less than 50 m thick and over 20 km long, at the base of the upper Aillik group. The occurrences hosted by the rhyolitic rocks, numbering over fifty and including the Michelin deposit, are in elongate structural-stratigraphic belts or zones, and are characterized by a pronounced enrichment of soda and depletion of potash associated with mineralization. The mineralized zones are affected to a varying degree by Hudsonian deformation, metamorphism and granitic intrusions.The uranium mineralization is interpreted as genetically related to the felsic volcanism, involving syngenetic deposition in argillaceous-tuffaceous beds and epigenetic emplacement in rhyolites. The volcanic activity occurred 1855 ± 5 Ma ago according to a preliminary U-Pb zircon date on porphyritic rhyolite. Pitchblendesfrom the Kitts and Michelin deposits and a few other occurrences in rhyolites have yielded nearly concordant dates in 1810 to 1730 Ma range. They reflect resetting of isotopic equilibrium at the time of Hudsonian deformation. Other isotopic data on pitchblendes and galena from veins and aggregates .in the south near the 'Grenville Front' indicate local redistribution of uranium and radiogenic lead at the time of Grenville Orogeny approximately 1100 Ma ago."

Jan 1, 1986

By Leandro Gustavo Mendes de Jesus

A teoria de Kubelka-Munk é bastante genérica e abrangente. A sua aplicabilidade já foi estudada nas mais diversas áreas, como tintas especiais [1], plásticos [2,3], produtos farmacêuticos [4] e alimentícios [5], e também no caolim [6-8]. A partir da teoria pode se relacionar a reflectância difusa com a função de Kubelka-Munk É também notável que carvões com elevados teores de cinza possuem propriedades colorimétricas diferentes de carvões com baixos teores de cinza. Em função dessa notável diferença acredita-se poder quantificar a quantidade de cinzas a partir da reflectância em diversos comprimentos de onda. Para isso foi elaborado um roteiro de retirada da amostra e confecção de pastilhas de carvão pulverizado onde foram medidos a reflectância e o percentual de cinzas. A partir dessas medidas foi possível a obtenção de equações que modelam a função de Kubelka-Munk em função do percentual de cinzas. Apesar do baixo número de amostras coletadas foi possível se obter funções de Kubelka-Munk que se encaixaram nos dados coletados. Por fim, foi possível concluir que há possibilidade de inferir o teor de cinzas de carvão por meio da reflectância.

Aug 8, 2018

By Jack C. Haptonstall

This paper describes the analytical characteristics of Western subbituminous coal and the manner in which these characteristics apply to their use in a utility-sized steam generator. It compares these characteristics with those of typical Midwestern coal and Eastern bituminous coal. The paper also reviews in detail the design considerations that must receive attention when various blends of these three coals, or any combinations thereof, are planned to be used. This research paper describes variations in analytical and utilization characteristics when coals from different origins are blended in order to achieve a predetermined sulfur content for the purpose of predicting sulfur oxides emissions as they affect environmental regulations and the resulting alterations in utilization characteristics such blending would cause, and how such blends of coal would affect a utility-sized steam generator.

Jan 1, 1979

By David R. Hanson

Seismic tomographic imaging, based on the same principles as a medical CAT Scan (Computer-Aided-Tomography). has been used for many years in the oil industry for large-scale subsurface stratigraphic characterization. and has most recently been applied to various structure- and stress-related problems in the coal industry. New developments in signal processing have greatly enhanced the speed, resolution, and range of applications of topographic imaging in underground settings, and recent innovations in data acquisition hardware have further increased data reliability and repeatability. Whereas past structure mapping applications relied on Seismic velocity and/or attenuation tomopraphy within an enclosed seismic source gram receiver array, recent developments in "True Reflective Tomography- (TRT TM) have expanded the application of this technology considerably. For example, in-seam TRT TM seismic reflection tray now he used to image structure, and/or old workings from one general location in the mine face areas of mains and panel developments) well ahead of planned developments largely eliminating the need to probe-hole drill on regular intervals. This new reflective technology bas also been combined with traditional cross-hole seismic tomography-providing a comprehensive, powerful tool for velocity attenuation. and reflective imagine utilizing the same source/receiver array data sets (borehole-to-borehole. borehole-to-entry and entry-to-entry). These new developments in data acquisition and image processing have greatly expanded the variety of applications for tomographic site characterization allowing the mine operator considerable flexibility to cost-effectively characterize previously inaccessible areas of the property. This paper presents examples of 2-D and 3-D .seismic topographic imaging applied to (1) the location of old works in Appalachian room-and-pillar operations and (2) the identification of anomalous zones ahead of mining/tunneling developments these applications demonstrate the state-of-the-art in seismic ground imaging using velocity, attenuation. aril reflection techniques land combinations thereon, and further illustrate the flexibility of data acquisition from a variety of tinning arid tunneling settings. Recent examples are presented from projects in the United States and Europe.

Jan 1, 2000

By J. D. Miller

The recent non-equilibrium electro-phoretic mobility measurements by laser-Doppler electrophoresis coupled with the stability and prevalence of collector colloids in soluble salt flotation systems suggest that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by hetero-coagulation. Previously reported flotation results confirm this surface charge/collector colloid adsorption model. However, the nature of the inter-particle forces responsible for hetero-coagulation of such oppositely charged particles at high ionic strengths remains to be determined. In this regard, atomic force microscopy was used for inter-particle force measurements at high ionic strengths. Model systems such as polystyrene/quartz and silica/sapphire were studied to measure the particle interaction forces prevalent at high ionic strengths. Results from this study indicate that while repulsive hydration forces exist between similarly charged hydrophilic particles, attractive forces exist between oppositely charged hydrophilic particles in high ionic strength solutions. The repulsive forces between similarly charged hydrophilic surfaces at high ionic strengths (2-4 M) are described by a double exponential function with decay lengths of 0.17 and 1.4 nm depending upon the surfaces involved. On the other hand, attractive forces were observed between oppositely charged hydrophilic surfaces at high ionic strengths (2-4M) and were described by a single exponential function with decay lengths of up to 9 nm depending upon the surfaces involved.

Jan 1, 1996

By David M. Gullikson

Since publication of the paper on the composition of California oilfield waters by Jensen (6)3/ in 1934 the only other information on the subject was published recently by Chave (4). To supply needed information on the composition of California waters in areas of current drilling activity, the Federal Bureau of Mines collected formation water samples for analysis. Thirty-eight samples from oil-and gas-producing formations in 12 fields located in Ventura, Kern, Glenn, and Colusa counties were analysed by the Bureau's San Francisco Petroleum Research Laboratory. The samples were selected particularly from fields where the water composition was not well known or where interpretation of electrical logs has been difficult and the interpretation may be affected by unusual composition of the water. These samples were obtained from rocks ranging in geologic age from Cretaceous to Upper Pliocene. Fifteen constituents of these waters were determined including sodium, potassium, calcium, magnesium, strontium, barium, lithium, chloride, iodide, bromide, carbonate, bicarbonate, sulfate, borate, and residual acidity. These analyses are the first to be published on California oilfield waters in which determinations for potassium, strontium, bromide, iodide, boron) and naphthenates were made on a significant number of samples. The electrical resistivities of tae samples were determined at 75° F. and 175° F.

Jan 1, 1961

By Xinming Chen, Huazhe Jiao, Qi Zhang, Yunfei Wang, Liuhua Yang

The effect of initial damage generated by weakly cemented interlayer surfaces on the physico-mechanical properties of layered cemented tailings backfill (LCTB) is considered for the interlayer inclination structure generated by multiple layered backfills in large-scale mining voids. Utilizing the theory of damage mechanics, the damage evolution and constitutive model of LCTB with interlayer inclination is constructed by considering the coupling of interlayer inclination effect and loading. Based on Mitchell’s mechanical model, we analyze the damage mechanism of the inclined cementation surface of LCTB, and derive the expression for the strength of LCTB considering interlayer inclination. The mechanical properties test of LCTB with different inclinations was carried out, and the results showed that the damage model of LCTB established was highly consistent with the experimental curves, which verified the correctness of the model. The initial inclination damage leads to the decrease of adhesive cohesion of cemented surface, and with the increase of inclination, the separation of layered surface, aggravation of misalignment, layered cemented surface is more prone to shear damage, and the mechanical properties of cemented tailings backfill in the lower part of layered surface are not effectively played, which reduces the overall performance of the material.

Nov 23, 2023

By N. A. Eilertsen, Rolf S. Paine

The Bureau of Mines studied the presplitting technique used for controlling overbreakage in the walls of a vertical shaft at the U.S. Army Corps of Engineers Littleville Dam project near Huntington, Mass. The periphery of the shaft, the dimensions of which were 16-1/2 feet wide by 21 feet long and 52 feet deep, was presplit (cracked) in the solid to a depth of 48 feet prior to full-depth sinking. Presplitting prevented overbreak in a fairly soft schist and provided sound self-supporting walls which required very little scaling.

Jan 1, 1965

More than 100,000 people from 110 countries involved in the construction aggregates and ready mix concrete industries are expected to attend Conexpo-Conlagg '99 in Las Vegas, NV March 23-27. The exhibition, the largest of its kind in the Western Hemisphere, takes place every three years. It is held at the Las Vegas Convention Center, Las Vegas Hilton Center and Pavilion. The show serves as a venue for con- tractors and others involved in aggregates construction to view the latest in equipment, technology and services. More than 1,500 exhibitors will use more than 147,200 m2 (1.6 million sq ft) of indoor and outdoor exhibit space. Attendees include presidents and company owners, sales and marketing managers, general managers and project managers. An estimated 20% of the attendees will be from outside of the United States. New for the Conexpo-Conlagg '99 show is a 3,715- m2 (40,000-sq ft) Information Technology Pavilion. This event, organized by AIEIC Systems, will showcase computer technology for the architectural, engineering and construction industries. Shown in the pavilion will be the latest developments in cost management, estimating, bidding, project management and accounting. In addition, the Information Technology Pavilion will demonstrate the latest in computer-aided design software, systems and services. Conexpo-Codagg '99 will also emphasize live demonstrations of exhibitor's products. Individual exhibitors will demonstrate their machinery so attendees can see the latest technology in action. Because the Conexpo-Codagg exposition is so large, "shows within a show" have been created to help attendees locate the products and services best suited to their interests. Seven product concentration areas will be formed. Each area houses suppliers and manufacturers of similar products or services.

Jan 1, 1999

By Robert Macdonald, William Coombe, John F. Lewry

Gold occurrences have been known in the La Ronge Domain for many year . Mineable reserves have more recently been outlined and there is every prospect of a major gold camp being established in the domain within this decade. The La Ronge Domain lies in the Lower Proterozoic 'Trans-Hudson Orogen' and is part of a collage of Early Proterozoic crust comprising volcanoplutonic arcs, batholiths, associated volcaniclastics and volcanogenic sediments lying between the Superior Craton to the outheast and the reworked Archean basement/Aphebian cover terrain to the northwest. The domain has several lithostructural subdivisions, the most important of whjch , from a gold exploration point of view, is the Central Metavolcanic Belt. This belt is composed dominantly of a range of metavolcanic rocks and gabbroic to granitic intrusives, which geochemically resemble younger subduction-generated 'primitive' arcs developed on oceanic crust. U-Pb zircon geochronology indicates that the arc volcarusm and pre- to late-kjnematic plutonism occurred about 1890 Ma to 1850 Ma ago. The belt has an attained grade of upper greenschist to amphibolite facies and is relatively undeformed , though high strain zones occur locally. Most gold occurrences in the La Ronge Domain have been found in the Star-Waddy Lakes area of the Central Metavolcanic Belt, and in the Sulprude-MacKay Lakes area to the south which is interpreted as a tectonically dismembered part of the main belt. Both tratiformand vein-type gold occurrences are present in the domain; vein-type predominate and form nearly 90 per cent of the occurrences. The stratiform-type occurrences show a regional lithological a sociation with iron-rich sediments within proximal felsic volcanjc sequences. Some vein-type occurrences appear related to brittle fracturing associated with intrusive emplacement (the magmatic-hydrothermal "syn:' and "subvolcanic" veins) and faulting. However, most of the vein-type occurrences exhibit a spatial association with regionalscale ductile shear and other high strain zones, and were probably formed by metamorphichydrothermal processes.

Jan 1, 1986