Search Documents

By H. C. Fuller

A method was devised and developed by the Bureau of Mines for decomposing manganese sulfate at significantly lower temperature than that required by the conventional procedure of using heat alone. This technique, called the partial reduction method, effected decomposition at 700° to 800° C, as compared to 900° 1,000° C normally required. The process consisted of heating, in the absence of oxygen, a mixture of manganese sulfate and a controlled quantity of a reducing agent. The suitability of commercial-type equipment was tested in laboratory-size models of an externally heated rotary kiln, a r bbled muffle-hearth furnace, and a fluidized-bed reactor. The rabbled-hearth furnace gave the best results with the least operating difficulty produced a gas containing more than 80 percent SC and eliminated 96 percent of the sulfur when coal was used as the reductant. Sintering of the powdery decomposition product produced an agglomerate containing, in percent, 63.6 Mn and 0.4 S.

Jan 1, 1966

By V. A. Chanturiya

There is an obvious disproportion in Russia gold-mining industry between the structure of gold reserves and the gold-mining techniques. The bulk of gold (over 70%) is extracted from alluvial deposit, 20%~25% from bedrock occurrences and 5%~7% from complex copper-zinc and polymetallic ores. The proved gold-bearing reserves are distributed as follows: alluvial ?19%, bedrock ?80%, the latter being sufficient to supply gold at the current production level for 100 years to come. In Russia, like elsewhere in the world, development of primary gold deposits is considered a first-priority line of development for gold-mining industry. Most of the gold-containing ores characteristic of Russian gold deposits are resistant ores with gold content varying between 3 ppm and 5 ppm usually showing quite low gold and silver recovery by cyanidation. Processing resistance of gold-containing mineral complexes is related to the presence of gold particles of submicrometric (<1.0 µm) and nanometric (10~100 nm) size, mostly asso-ciated with pyrite and arsenopyrite. Therefore switching over to processing bedrock entails a num-ber of technological problems that stem from chemical and physical resistivity of ores. The chemical resistivity can be overcome through flotation, oxidation roasting, autoclave leaching (biohydro-metallurgical oxidation), etc. The physical resistivity can be dealt with by resorting to traditional power-intensive methods,e.g. grinding to a ?40µm size, thermal treatments of sulphide concentrates and non-traditional high-energy methods of liberating the sulphides by means of power attack, e.g. electro-chemical oxidation, exposure to electron beam radiation and other methods. The modern non-traditional processes for treatment of rebellious noble metal-bearing ore, aimed at improving disintegration efficiency for finely dispersed mineral complexes are analysed. Advantages and perspectives of a new high-efficient, energy-saving and ecologically safe process of the nanosecond high-power electromagnetic pulses (HPEMP) effect are proved. The said process provides a stable increase in the valuable component recovery at lower energy consumption and production costs of the finite product at the stage of dressing rebellious gold-bearing ores and concentrated products. The experimental data prove high efficiency of the preliminary impulse treatment, thus, the increase in the gold recovery at the cyanidation stage amounted to 4%~12% from rebel-lious ores, 10%~30% from gravity concentrates, 5%~45% from flotation concentrates, 30%~80% from oil flotation tailings.

Jan 1, 2014

By Michael Clar

Total suspended solids (TSS), generally referred to simply as sediment, is one of the four major parameters of water pollution associated with surface mining activities. The other three para¬meters are iron, manganese and pH. Currently the Environmental Protection Agency (EPA) is in the process of developing and implement¬ing effluent limitations for these pollutants pursuant to section 301 of the Federal Water Pollution Control Act Amendments of 1972, 33 USC 1811.1 To date, effluent guidelines for existing point sources have been published, and guidelines for new sources are forthcoming. The effluent limits which have already been developed for TSS have been subjected to some controversy.1 Some industry spokesmen have indicated that they may be unable to meet these effluent limitation guidelines for TSS. The industry claims that in certain areas the suggested limit is unattainable since high suspended solid loads already exist in streams due to numerous and various sources of nonpoint pollution which include agriculture, silviculture and urban construction for which no TSS effluent limits have been set. An opposite viewpoint asserts that the TSS limitations are too lenient since permit data from the Regions (U.S. EPA Regions) indicates present compliance for several companies under more stringent TSS limits. The experience at the Centralia mine in Washington is one example.2

Jan 1, 1977

By R. L. Amelunxen

P. T. Freeport Indonesia (PI) in conjunction with Crescent Technology Inc. has developed a method to predict the metallurgical performance of ores blends based on the behavior of their component ores. The question addressed in this paper is whether ores treated individually could be extrapolated to predict the behavior of a blend of ores. The work further investigates the use of modal analysis to establish individual mineral flotation kinetics in each of the ore zones. This information would lead to the prediction of grade-recovery curves of ores made up of those minerals. Nine samples of ore, representing various zones of FI&apos;s Grasberg ore deposit were tested metallurgically and examined microscopically. The same testwork was performed on blends depicting the 1994 mill quarterly feed. Flotation kinetics of the individual ores were then "mathematically" blended and compared to the results obtained from the quarterlies. The calculated kinetics of the actual blends of ore received by the mill were fed to the simulation program and compared to the actual mill performance.

Jan 1, 1995

By Vinay Jain

Beneficiation of alumina rich iron ore slimes is a major challenge for the Indian iron ore industry. One of the methods by which this problem might be addressed is by design/screening of suitable reagents (flocculants/depressants/collectors) which act selectively towards either aluminum containing minerals (gibbsite and kaolinite) or iron bearing minerals (hematite and goethite) in order to separate them. Our earlier work indicates that separation of iron oxide minerals from gibbsite is relatively more difficult than from kaolinite. Accordingly, our research work has been focused on finding selective reagents for iron oxide ? gibbsite separation. We have performed density functional theory (DFT) computations to evaluate the interaction energies of seven different reagent groups - carboxylic acid, flotol, hydroxamic acid, phosphonic acid, iminobismethyl phosphoric acid, xanthate and starch with hematite and gibbsite surfaces. The objective was to identify if any of these groups show selective adsorption towards one of the mineral surfaces. Among all these reagents, starch exhibits the highest selectivity towards the hematite surface with a difference in interaction energy of ~63 kcal/mol between hematite and gibbsite surfaces. This is consistent with experimental findings at our laboratories on slime samples from Noamundi mines wherein it is being observed that usage of starch as a flocculant does lead to an improvement in the final grade of the ore with significant reduction in the Al-content. A binuclear complexation mechanism based on affinity between Fe and Ostarch atoms combined with a geometrical templating effect, arising out of a close correspondence between Fe-Fe distance on the hematite surface and O-O distance in starch, is proposed to explain the strong adsorption of starch on hematite surface. Keywords: slimes, iron ore, alumina, hematite, gibbsite, DFT, adsorption, flocculants

Sep 1, 2012

By Nigel Marx

In order to understand (and ultimately to predict) the friction reduction resulting from the use of polymer solutions, the rheological properties of model polymer solutions have been measured over a wide range of shear rates. Both temporary and permanent shear thinning have been observed. By using base fluids of different viscosities it has been shown that permanent shear thinning depends more closely on the shear stress experienced by the fluid than on the strain rate. Hydrodynamic measurements have been made on the polymer solutions using a compliant ball on flat lubricated contact that operates in isoviscous-elastic conditions. The measured friction values can only be predicted with reasonable accuracy if the measured shear thinning properties of the lubricant are taken into account in the hydrodynamic model.

Jul 31, 2018

By N. Jovanovic, A. Vazirizadeh

"The main objective of this study is to find a solution to design a mass flow observer system with the minimum required sensors and maximum observability for a mineral processing plant. The second objective is designing a mass flow observer configuration with high reliability to manage sensor failures. This configuration will provide a robust monitoring system that increases plant availability and process measurement fault detection. Furthermore, the monitoring system is expected to improve process efficiency. In this investigation, the procedure of designing an observer system is presented along with three models to design the sensor network. The advantages and disadvantages of each models are discussed and finally the models result for an industrial case are presented and analyzed. INTRODUCTION The concepts of observability and redundancy of mass flow are directly linked with the ability to solve and estimate the mass flow. There are hundreds of streams in a process plant flowsheet, and for technical and economic reasons it is not possible to measure all mass flows. It is thus important to know for a set of measured streams, which of the unmeasured streams can be estimated. The concept of observability deals with this issue. It is also valuable to know whether a measured mass flow of streams can be estimated even if a sensor fails for some reason. Redundancy deals with this failure question. A stream is said to be observable if it can be estimated by using the measurements and/ or mass conservation equations. Also, a stream is redundant if it is observable even when its measurement is removed. Observability and redundancy analysis can be exploited for adding new measuring instruments. It can also play a useful role in efficient decomposition and data reconciliation problem (Narasimhan and Jordache 1999). The value of an observer system cannot be justified without considering its benefits. This justification is done through evaluation of data reconciliation, gross error detection and improving process performance such as outlined below:"

Jan 1, 2018

By Ralph W. Marsden

The natural iron ores of the Lake Superior Region in the United States are being replaced by iron-ore concentrates produced from magnetite- or hematite-rich horizons in the Precambrian cherty iron formations. The production of natural ores will soon be less than one-half of the total ore shipped annually. The tonnage of natural ore produced will continue to decline until it is a minor percentage of the ore shipped. The natural ores include (1) soft ore, (2) hard ore, ( 3) conglomerate ore and ( 4) siliceous ore. The soft ores are the important ore type and are sometimes termed "Lake Superior type ore". These ores are in situ deposits of hematite and limonite formed by the leaching of silica and other gangue materials in the iron formations. The leaching is believed to have been done by downward moving surface waters. In deep ore deposits, generally over 1000 feet below the present surface, circulation and leaching action may have been assisted by hydrothermal activity. Hard ore deposits occur on the Vermilion and Marquette ranges where hematite or magnetite has replaced the silica (and possibly some silicates) in cherty iron formation. These ores commonly occur in structural situations favorable for the movement of hydrothermal waters. The ores are believed to be the result of hydrothermal action with iron, possibly from the iron formation, transported by hydrothermal waters to areas favorable for the replacement of silica by iron oxides. Certain stratigraphic horizons of the Lake Superior Precambrian cherty iron formations contain sufficient iron as magnetite or hematite, with a grain size and texture that will give adequate mineral liberation, to yield an ore-quality product after grinding and concentration. The magnetite-rich deposits are termed magnetite taconites. These ores occur on the Mesabi, Gogebic, and Marquette ranges. Magnetite taconite ores are unenriched cherty iron formation and are the result of the sedimentary deposition of the iron formation and the metamorphic history of the rock. The commercial quality hematite-rich iron formations in Michigan are termed jasper ores. The jasper ores are being mined on the Marquette and Menominee ranges. These ores are composed of specular or granular hematite associated with quartz and iron silicates. The jasper ores appear to be recrystallized iron formations in which iron, prior to recrystallization, occurred as hematite.

Jan 1, 1968

By A. K. Kyllo

A study has been carried out on the dusts from Hudson Bay Mining and Smelting&apos;s Flin Flon copper smelter. The aim of the work was to determine the mechanisms of dust formation and the deportment of the various constituents. The work concentrated on the copper converters, but the electrostatic precipitators and baghouse also clean the reverberatory furnace off gas, so some mixing will have occurred. The dust composition was found to vary with distance from the furnace, and to be made up of three major components: solidified droplets, unreacted flux, and condensed particles. The solidified droplets were formed from material ejected from the converter during blowing, while the flux was blown out of the converters immediately after charging. The condensed particles contained the majority of the lead and zinc, as well as the volatile impurities. There was also a significant soluble content of the dusts, increasing with distance from the furnace. The condensed material may be separated from the remainder by a simple washing and sizing technique.

Jan 1, 1996

By Peter C. Wood

This report describes research directed toward the preparation of chemical oxygen (02) sources which exhibited improved 02 storage and reaction characteristics when compared to potassium superoxide (KO2). The initial focus of the research was the preparation of calcium superoxide (Ca(02)2) by the disproportionation of calcium peroxide diperoxyhydrate. The Ca(02)2) was characterized by chemical, thermal, and x-ray analyses. Several methods for scaling up the Ca(02)2 synthesis process were studied. Next, the reactivity of Ca(02)2 toward humidified carbon dioxide (C02) was evaluated and was compare o that of K02 under flow-test conditions approximating those existing in portable breathing apparatus. The reactivities of mixtures of K02 and Ca(02)2 or lithium peroxide towards humidified CO2 were also studied. Finally, an analysis of two commercial, K02-based, self-contained self-rescuers was conducted to determine the potential weight and volume savings which would be possible if Ca(02)2 or a mixture of K02 and Ca(02)2 were used as a replacement for K02.

Jan 1, 1983

By M. Palfreyman

"Most of the minerals employed in Canadian refractory production are imported; in fact, most of the refractories consumed in Canada are imported. Whereas this situation is partly due to a definite shortage of suitable raw materials, e.g., fire clays, it is possible that the potential of certain mineral deposits which could be usefully exploited has not been recognized. There are exceptions, notably magnesite and dolomite, from which refractories are produced in Canada.In many cases, known mineral deposits are located either in inaccessible areas or in areas where transportation would be a major economic factor. This paper lists some minerals and their respective known deposits which could be employed in the production of refractories, irrespective of economics."

Jan 1, 1973

By Eirik Sundvor, Hany Doss, Peter Vogt, Kathleen Crane

"Abstract - In 1989-1990, the SeaMARC II side-looking sonar (11 to 12 kHz) and swath bathymetric system imaged more than 80 000 km2 of the seafloor in the Norwegian-Greenland Sea and southern Arctic Ocean. One of our main goals was to investigate the highly oblique (115°) junction between the Mohns and Knipovich ridges, and to determine, using new morphotectonic data, whether or not this junction is stable or in a state of readjustment. These findings are presented in this paper.Along the northern Mohns Ridge, we observed a highly segmented rift valley undisturbed by transform faults. In contrast to the elevated Reykjanes Ridge, the Mohns Ridge is dominated by deep en echelon fault-bounded troughs, which are bordered by high rift valley volcanoes. These segment boundaries are interpreted to be sites of recent to present volcanic activity, based on their high acoustic reflectivity. The northwestern flank of the Mohns Ridge is marked by shallow quasi-linear ridges parallel to the present orientation of the Mohns Ridge. The orientation and geographic position of these ridges suggest that they were formed at the Mohns Ridge. Only in the northernmost cases are some of these off-axial ridges non-linear. The degree of the non-linearities increases slightly with proximity to the Mohns-Knipovich bend. In addition, because no transform fault was detected between the Mohns and Knipovich ridges, we conclude that the Knipovich Ridge must be obliquely spreading to the NW-SE."

Jan 1, 1999

By M. J. Sapko

The U.S. Bureau of Mines has developed a portable meter for measuring the component concentrations in binary dust mixtures whose constituents have different optical reflectivities. The meter has been successfully tested with coal dust-rock dust mixtures taken from coal mines in Europe and the United States and fluorinated-carbon mixtures that change from carbon black to pure white during fluorination. Additional study has also substantiated the theoretical expressions used in the design of the meter.

Jan 1, 2010

By W. C. Clark, J. B. Schloen

Two papers have been written, previously concerning operations at the Montreal East plant of Canadian Copper Refiners Limited. The first one,&apos; written in 1932, described silver-refinery operations at the time for producing silver and gold bullion from tankhouse anode slimes; the second,Z published in 1933, consisted of a description of the entire plant. Since publication of these papers the refinery has become the world&apos;s largest producer of refined selenium. The first selenium was produced in August 1934. Tellurium production on a commercial scale followed in October 1935. This paper will deal with selenium and tellurium production and also with present operations in the silver refinery. Blister cakes from Hudson Bay Mining and Smelting Co., Flin Flon, Manitoba, and commercial anodes from Noranda Mines Limited, Noranda, Quebec, are refined at Montreal East. Both these bullions have unusually high gold, selenium and tellurium content. The average assay of raw slimes produced from domestic and Noranda anodes is about 40 per cent Cu, 3600 oz. per ton Ag, 800 ox. per ton Au, 22 per cent Se and 3.7 per cent Te. Early Silver-refinery Operations From the start of operations in 1931 until July 1934, the raw slimes were oxidiae-roasted at 700&apos; F. in a Nichols-Herreshoff furnace, acid-leached with tankhouse discarded foul electrolyte (20 per cent HzSOa), filtered and charged directly to the dor6 furnace for refining to dore metal. This is the customary method for treating tankhouse anode slimes but was not suitable at the Montreal East plant because of the high selenium and tellurium content of our slimes. In the acid-leaching process about 50 per cent of the selenium and tellurium in the roasted slimes was dissolved in the electrolyte. These elements were recovered with the copper as a sludge in a small electrolytic

Jan 1, 1944

By Arkady Senchenko, Yevgeny Zhagun, Yury Kulikov, John Starkey

"The paper contains description of a new project in Russia - gold-processing plant at Aleksandrovskoye deposit (start up in September, 2013). The paper includes a brief description of plant flowsheet, data for material composition and technological properties of ore, as well as information about the achieved parameters of ore processing over the first months of plant operation. The project is interesting because a new semiautogenous mill and a ball mill were purchased on the basis of SAGDesign Consulting Group recommendations after the testing of ore samples characterizing the deposit according to specific years of operation. The plant has relatively small design capacity - 750 000 tpa, but nevertheless is the biggest gold-processing plant in the territory of Zabaikalsky region. Major valuable component in the ore is gold, silver is recovered as a by-product. The ores are very hard to grind. The design grinding flowsheet includes a semiautogenous mill operating in closed circuit with a screen, and a ball mill operating in a closed circuit with hydrocyclones (SAB). Process technology includes gravity processing and flotation with subsequent cyanide leaching of concentrates. Mill operation analysis and conclusions about the compliance of the achieved values to target ones are shown, as well as the accuracy of SAGDesign method when applied to very hard ores of Aleksandrovkoye deposit are presented in this paper. Basic directions of technological flowsheet optimization are also given."

Jan 1, 2014

By T. Khumalo, L. Musenwa, S. Masemola, M. Kgaphola

"In 2017, Petra Diamonds completed the construction and commissioning of a modern, fit-for-purpose diamond processing plant at Cullinan Diamond Mine (CDM). The design of CDM’s milling circuit is unconventional in that it comprises an autogenous (AG) mill with a grate discharge with large ports, low-revolution jaw crushers, and high-pressure grinding roll crushers with large operating gaps. In this paper we review the design to provide guidance on what is expected from the milling circuit and to demonstrate how the design aims to address challenges experienced in the old plant, which was based on staged crushing technology. We assessed the performance of the CDM AG milling circuit from commissioning and early production stages to examine its impact along multiple dimensions. In the assessment we sought to understand the lessons from our milling circuit regarding diamond liberation, energy consumption, and the future of diamond processing as a whole. IntroductionCullinan Diamond Mine (CDM), previously known as Premier Mine, is an underground diamond mine owned by Petra Diamonds. Petra Diamonds is a leading independent diamond mining group and a growing supplier of rough diamonds to the international market. Petra Diamonds is listed on the Main Market of the London Stock Exchange under the ticker ‘PDL’. Petra’s total resource of 305 million carats ranks third by size after De Beers and ALROSA (Petra Diamonds, 2018).CDM was established in 1902. The mine rose to prominence in 1905, when the 3106 carat Cullinan Diamond — the largest rough diamond of gem quality ever found — was discovered there. The mine has produced over 750 stones that are larger than 100 carats and more than a quarter of all the world's diamonds that are larger than 400 carats. Cullinan is renowned as a source of large, high-quality gem diamonds, including Type II stones, as well as being the world’s most important source of very rare blue diamonds (Petra Diamonds, 2018)."

Feb 1, 2019

By J. M. Mutmansky, C. Lee

"Measurement of the size and elemental characteristics was performed on airborne coal mine dust samples collected by multi-stage cascade impactors as well as channel samples of the geologic materials. Size distributions were obtained using precise weighing techniques on the impactor substrates. Elemental analysis on the samples was performed by the proton-induced x-ray emission (PIXE) method, a rapid and non-destructive method of multi-element analysis.The various analyses were performed on 9 major and 21 trace elements. The results indicate the importance of intake air and shuttle car movements as sources of dust. The association of coal dust characteristics with channel samples was investigated using the coefficient of proportional similarity as a statistical measure. Results show a strong relationship between major elements and the geologic material being cut but a similar relationship between trace elements and geologic materials is not consistent.1. INTRODUCTIONThe most significant occupational disease in the coal industry is known ·as coal workers' pneumoconiosis (CW'P). While CW'P has existed for centuries, its mechanism of occurrence and association with coal dust has been well understood for only a few decades. In the 1930s, the significance of this disease led state and government officials in the USA to perform extensive epidemiological and environmental studies in the major coalfields. Study of these results plus later studies in the coal producing countries of Europe eventually led to the dust regulations that appear in the Federal Coal Mine Health and Safety Act of 1969.The impacts of the 1969 act were a productivity decline and increased production cost. Many analysts attributed this in large part to difficulties in complying with the new dust standards (Brezovic 1981). However, compliance was met in most continuous miner sections rather quickly. The remaining problem area is that of longwall mining where the procedures and layout of the minin~ system make it difficult to meet the standards."

Jan 1, 1989

By Harry Siewert, Tom Milner, Jack Stickney

"LocationThe Gibraltar mine is located in central British Columbia (NTS 93B/9W), 362 km north of Vancouver. Access is provided by 20 km of paved road from McLeese Lake, which lies 45 km north of Williams Lake on Highway 97. Latitude and longitude of the mine are 52° 30' and 122° 16', respectively.The total area of the McLeese Lake site is approximately 1700 ha (4200 acres). This includes the orebodies, dumps, surface drainage collection system, plant site, roads and tailings ponds.Brief Description of OperationOre is mined by open pit methods and is concentrated using conventional crushing, grinding and flotation processes. Copper and molybdenum flotation occurs at an average rate of 40 000 tons per day. Tailing is discharged to an impoundment area and the water recycled as process water. Additional copper is extracted from the waste dumps using sulphuric acid as a leach solution followed by solvent extraction and electrowinning.HistoryExploration by Gibraltar began in 1964, continuing until late 1970, at which time it was announced that the property would go into production. Construction started in early 1971, with initial production in March 1972. Target capacity of 30 000 tons per day was achieved by the end of March and is currently at 40 000 tons per day.Ore reserves as of January 1, 1998 were 184 384 000 tons grading 0.31% Cu and 0.010% MoS2."

Jan 1, 2000

By G S. Beros

In 2019 the Chinese Ministry of Ecology and Environment issued guidelines promoting the implementation of ultra-low emissions in the iron and steelmaking industry. These guidelines aim to drive improvements in air quality through the reduction of particulate matter (PM), sulfur dioxide (SO2) and nitrogen oxide (NOx). Secondly, it also represents an initial means to commence decarbonisation of the industry. The ultra-low emissions guidelines propose that well over 80 per cent of China’s production capacity will achieve these targets by 2025. In response, many sintering operations have implemented numerous improvements to the process that result in significant efficiency gains. Of note is the adoption of deep bed sintering where, with some modifications to equipment, the sintering bed depth is increased resulting in sizable reductions of SO2 and NOx emissions. This paper will also provide an overview of the requirements to introduce deep-bed sintering into an operation and highlight test work completed which quantifies the resultant reduction in emissions.

Nov 8, 2021

By D. L. Paulson

The Bureau of Mines used 50-and 800-kva electric-arc furnaces to confirm the feasibility of producing ferronickel in electric-arc furnaces from pre-reduced concentrate from the Yugoslavian FENI project. The relationships were established among metallic iron concentrations (degrees of prereduction), ferronickel grades, and nickel recoveries. Smelting the concentrate containing 1.27 wt-pct nickel and metallic iron levels between 2 and 3 wt-pct, produced 15 to 20 pct ferronickel. Higher or lower metallic iron concentrations were compensated by adding oxide pellets or carbon to the electric-arc furnace charge. Over 90 pct of the contained nickel was recovered when up to 20 pct ferronickel was being produced. Data obtained while smelting 16 tons of prereduced concentrate in the 800-kva electric-arc furnace indicated ferronickel can be recovered at an energy consumption of 530 kwhr/ton of prereduced material.

Jan 1, 1977