Search Documents

By Greg Plutko

Laboratory testing has shown that the Marsh Funnel test can be significantly impacted by long-chain polymer entanglement. In general, shorter hydration time leads to more chain entanglement which in-turn, leads to higher marsh funnel values that values seen for longer mixing. This trend makes it very difficult to predict funnel-viscosity on successive days. Data is presented which helps to explain this chain interaction effect on Marsh Funnel data and how it differs from traditional Fann viscosity. The data suggest that this long-chain polymer entanglement occurs more in samples with less hydration time and decreases as hydration time increases. There is also suggestion that higher polymer concentrations have a greater drop-off in marsh funnel viscosity for a given aging length than do lower solids slurries. Fann rheology was shown to be much less impacted by the hydration time of the PHPA polymers than was Marsh Funnel viscosity. This suggests that the Marsh Funnel viscosity is impacted by some aspect of the slurry that does not affect Fann rheology as strongly. It is known from literature that longer-chained polymers have more potential to entangle and our data support the theory that the Marsh funnel viscosity is greatly impacted by this polymer-chain ‘roping’ entanglement.

By Ernest E. Thurlow

The Geology Division of Northern Pacific Railway Company has adapted to its exploration efforts field procedures for geochemical sampling and semi-quantitative analysis which have been developed through research by the U. S. Geological Survey. The sampling is done in conjunction with reconnaissance geologic mapping on aerial photographs or during field checking of maps which have been prepared largely by photogeologic interpretation.. Stream sediment or soil samples are taken and readily soluble combined heavy metals are extracted with ammonium citrate followed by colorimetric titration with dithizone at the sample site. The effectiveness of this approach has been demonstrated both in positive and negative results, thereby assisting in the elimination of large areas of land from further immediate attention and in providing targets for followup exploration. An occasional sample is submitted for spectrographic analysis as a check on the possible presence of other elements of economic significance. Field laboratory procedures are also being implemented for determining molybdenum, mercury, and other metals which may be valuable in themselves or useful as pathfinder elements in outlining mineralized areas. A lead-zinc occurrence in Oregon and a copper deposit in Montana were readily detected and outlined by stream sediment and soil sampling and a heavy metal anomaly that lacks obvious interpretation has been found in northwestern Montana. Detailed mapping and additional sampling are followed by other exploration techniques if warranted.

Jan 1, 1964

By R. G. Siddall, W. Gale

In the UK the development of the science of strata control has been strengthened by a resurgence of interest in the specialism of roofbolting and its associated techniques. The evolution of the theories and practices of strata bolting in roadway stabilisation is discussed. Practical experiences are considered, principally the use of Australian techniques, the relationship between bond strength and annulus and the effects of stress in the ground. Areas of new technology such as cable bolting, injection anchors and on-board bolters are also discussed. The recent advances in computer technology and rock testing equipment and methods have provided the opportunity to simulate ground behaviour under various conditions. Computer modelling developments and the use of techniques to predict ground behaviour are described.

Jan 4, 1992

"In many gold deposits, a reasonable amount of the gold that remains in the cyanide leach tailing is associated with pyrite. Some gold plants have found it economical to incorporate gravity circuits on the cyanide leach tailing to recover the gold bearing pyrite before subjecting it to fine grinding, then recycling the ground pyrite back to the cyanide leach circuit. For low grade gold deposits the loss of gold bearing pyrite is exacerbated as the broader process economics normally favour a coarse grind (> 150 ?m). An option that has received attention over the last decade is to recover the gold bearing sulphides in the milling circuit by gravity, similar to the widely-practiced gravity recovery of free liberated gold. The modelling and simulation of a gravity gold circuit in a milling flowsheet is relatively simple compared with a gold bearing pyrite circuit, as the recycle advantages and breakage functions for gold and pyrite are quite different. This current work represents an attempt to simulate the gravity recovery of gold bearing sulphides in a milling circuit that also incorporates fine grinding, using relatively simple simulation models. The simulation results are further explored with reference to the economics of this type of circuit.INTRODUCTION It is well known that gold is associated with pyrite in most sulphide gold deposits and that the amount of gold associated with pyrite will vary from deposit to deposit. Most of the gold associated with pyrite is liberated in the grinding circuit during the processing of a gold ore. However, some gold remains occluded in the pyrite and is lost in the final leach tailings. Little information is available in the literature on methods to enhance gold liberation from pyrite by specifically removing pyrite, either in the grinding circuit or from the final tailings stream, and grinding it finer. One of the earliest record of this approach is described by King (King, 1949) where pyrite present in Witwatersrand gold ores was recovered by circular jigs and Johnson barrels followed by fine grinding of the concentrate prior to cyanide leaching. Dominy et al., 1970, provides information on the use of Yuba jigs to recover pyrite from the discharge end of ball mills. Again, the jig concentrate was ground to a fine particle size before cyanide leaching to recover the liberated gold. Unfortunately, no information is provided in these articles on the additional gold recovery from implementing these circuits in a flowsheet. Martins et al., 1993, provides details of a gravity circuit using Reichert cones and spirals to recover gold bearing pyrite from a cyanide leach tailings followed by fine grinding of the pyrite concentrate in a Tower mill. The ground concentrate returned to the front end of the already installed leach circuit. Overall recoveries were increased by some 2% to 4% depending on the amount of gold and pyrite in the plant feed."

Jan 1, 2017

By Malcolm T. Wane

The subject matter of this paper, "Applied Rock Mechanics?," has its genesis in a recent field trip taken by the author. A more or less standard question asked at the mines visited was "How are you using the principles of Rock Mechanics to assist you in maintaining an efficient, safe, and competitive mining operation?" The question was couched in a number of different forms, but the intent was to determine whether or not a general theory based on reason and the scientific method was applied or whether the alternatives of tradition, intuition, ?common sense', revelation, ?shotgun methods' or authoritarianism were invoked. Perhaps two responses to this query will be illustrative of the general nature of the replies. At operation XYZ an extension to the known ore body has been found. The extension is of large enough size and grade that a mining scheme using load-haul-damp techniques is envisaged. Since this represents a departure from the present mining scheme, questions have arisen regarding pillar sizes, room and entry sizes and possible support requirements. A task force has been set up to expeditiously plan for these things and write the necessary specifications and requirements. The fundamental question was posed to members of this group.

Jan 1, 1971

By P. J. Arps

Cyanide (CN) is used to recover gold from its ores in many locations worldwide. In spite of the established history of gold mining in Alaska, modern cyanidation methods have been used at only one location, the Ryan Lode Mine at Ester Dome, near Fairbanks. Ore was processed by heap leaching between 1987 and 1989, when permitting issues caused operations to be terminated. Those issues have since been resolved, and plans to reopen the mine are currently being discussed. Plans are also proceeding to develop several other ore deposits in the state, all of which include the use of cyanide for gold recovery [6]. Since tailings and effluent water produced from these mines will require treatment, it is important to develop detoxification methods suitable for the Arctic and sub-Arctic conditions found in Alaska. Several methods exist for removing cyanide from mining wastewater. However, most industrial users prefer chemical treatment systems, and typically use sodium hypochlorite, hydrogen peroxide, or sulfur dioxide/air/copper to oxidize free and complexed cyanides [9]. Biological treatment has been used successfully at two sites in the United States [30,32] and field tested at several others [20,27,28]. In addition, one mine uses "natural processes", which include natural oxidation, photodegradation, and degradation by naturally occurring bacteria [33].

Jan 1, 1994

By R. A. Beall

This paper summarizes the development of a furnace for producing titanium castings. The general problem is outlined and chronological details are given on the construction and operation of four different casting furnaces, all utilizing consumable-electrode arc heating and water-cooled copper crucibles. Of the two methods of pouring, the tilt-pour technique has been more satisfactory than bottom tapping. Mold design, electrode fabrication, and deep-pool production are discussed. INTRODUCTION In the early summer of 1953 the Bureau of Mines was contacted by the Department of the Army through Watertown Arsenal to explore the possibility of conducting research on casting titanium metal. The objective of the program was "to develop a technique for producing formed castings of titanium metal not less than 40 pounds in weight and without introduction of deleterious contamination."

Jan 1, 1956

The National Mining Hall of Fame and Museum in Leadville, CO seized the opportunity to show off during its 10th anniversary induction banquet on Sept. 6. "We wanted to make people more aware of the mining hall of fame and museum," said Carl Miller, its executive director. The annual event honors inductees into the Mining Hall of Fame. This year, the inductees included Paul Wheeler Allen, Joseph Rosenblatt, Arthur Fay Taggart, Joseph Toy, Joseph Wharton and John Benjamin Zadra (ME, August, pp. 60-63). Allen, of Pasadena, CA and Rosenblatt, of Salt Lake City, are both living. Only Allen was able to attend. This year's induction banquet was the first held in Leadville, North America's highest incorporated city, at 3,094 m (10,152 ft) above sea level. The banquet gave attendees an opportunity to see the museum in its century-old 6,500-m2 (70,000-sq ft) Victorian schoolhouse. Many of the 350 guests came in 1890s dress to the black-tie affair. The evening included a cocktail reception and an open house along with a catered, prime rib dinner. During the open house, attendees had the opportunity to tour the museum's 12 rooms of exhibits and displays. Among items of interest, it was noted that a framed directory of inductees now enhances the entrance to the hall of fame. The directory is organized by the inductees' names and the location of their plaques, allowing visitors to quickly find hall of fame members. Noted mining historian and author Duane Smith delivered the keynote address at the banquet. After the induction of the six honorees, attendees danced to the big-band era music of the Leadville 17-piece band BandAge. Karl Elers was the master ceremonies for the evening's program. He is a member of the hall of fame's board of directors and is chairman of Battle Mountain Gold Co. Allen was honored by the presence of 26 former colleagues and associates. He told the audience that he originally thought the museum should have been located in Denver. "But I have been proven wrong," he said. For many years, Allen was the operational executive of Cyprus Mines Corp. and a key participant in the company's growth. Allen received a replica of his mining hall of fame plaque from Thomas Falkie, chairman of the hall of fame's board of governors and president of Berwind Natural Resources Co.

Jan 1, 1997

SOME notes on the works of the Electrolytic Refining and Smelting Company of Australia will no doubt be of interest to members of the Institute, more especially as much of the work is new to Australasia.As many of the members who may read this paper have not been in a position to visit works of this kind, and are consequently not thoroughly acquainted with all the operations carried on, the author has taken the liberty, in some cases, to enter into explanation which would otherwise be unnecessary.The works are situated at Port Kembla (New SouthWales), about fifty miles south of Sydney, and are approachable both by rail and water. The Government has recently built a low-level jetty upwards of five hundred feet long, and intends installing at an early date an electrically operated portable crane to facilitate the handling of material to and from the boats. Thi.s will mean a considerable reduction in the length of time that boats are laid up at the jetty. There are also under construction two breakwaters, which, when complete, will materially assist shipping operations. The works as they exist are capable of turning out 1200 long tons of refined copper per month. It is gratifying here to note the unqualified success with whichthe E.S.A. refined copper met with on first being put on the market.

Jan 1, 1911

By P. H. Willis

Since the 14th CMMI conference, held in Edinburgh in 1990, at which a paper was presented by the author (Willis, 1990) reviewing the role of integrating new technology as a survival strategy for South African gold mines, considerable change has occurred in the South African mining industry. This paper reviews the current state of the industry and provides an update on the technologies discussed ten years ago. It reviews available technology and provides a broad economic assessment of these technologies if they were to be introduced in an integrated mining system with a focus on deep level mining below 3000 m. It also reviews possible future technologies currently being researched and developed by CSIR: Division of Mining Technology (Miningtek).

Jan 1, 2000

By B. Ceki, A. Mabentsela

The BCL furnace is scheduled to restart operations after being placed on care and maintenance in 2016 due to depressed nickel prices. The decision to start operations after such a stoppage ought to be led by a techno-economic evaluation of process options to make operations more resilient. For BCL, the decision lies between using the existing flash-smelting furnace (FSF) or a top-submerged lance (TSL) furnace. Available studies show that the FSF combined with other converting technologies is cheaper to operate; however, such studies are based on flowsheet simulation results of single copper concentrates and therefore do not provide a full scope of practical capabilities based on smelter operator skills. Using a t-test on normalized prior operational data from three Cu FSF and two Cu TSL, it was found that the only statistical differences between the operating costs of the FSF and TSL technologies are in the coal use for heating the feed blow and number of rebuilds: the FSF consumes coal to heat the feed blow and the TSL requires 2.4 rebuilds during a course of a single FSF campaign. A summative operating cost comparison over the existing BCL FSF 11-year life shows that BCL can decrease operational costs by some BWP 55.5 million if the operation were to change to the newer TSL technology. The savings derive from reduced coal use, which is normally associated with heating the blow when using the FSF. Despite the TSL carrying added costs of 2.4 rebuilds during a life time of one FSF furnace campaign, the cost associated with the TSL rebuilds of approximately BWP 1.3 million is minimal compared with the overall operational expenditure decrease that BCL will incur on using the TSL technology. In terms of the technology, BCL can have higher Ni–Cu recoveries at lower operational costs by elimination of Ni–Cu losses and eliminating the slag-cleaning furnace by converting to a TSL furnace.

Jul 10, 2024

By S Hancock, B H. Brady, H Muhlhaus

The aims of this paper are to present the governing science, verify the performance and demonstrate the potential engineering applications of a computational simulator for in situ leach mining of non-ferrous minerals. Assuming that the target mineral is deposited either uniformly within rock matrixes (matrix-hosted) or on fracture walls (fracture-hosted), in situ leaching can be treated as reactive flow and transport in geological media (porous media for matrix-hosted ore deposits and fractured media for fracture-hosted ore deposits). Under this treatment, the processes of in situ leach mining for non-ferrous minerals can be quantified through several sets of equations and these coupled equations have been numerically solved. The computational simulator has been applied to the simulations of one-, two-, and three-dimensional in situ leaching cases. The computational simulator, together with laboratory and in situ leaching tests, can be used to:optimise the leaching chemistry; optimise the in situ scale mining operations; scale up the in situ scale test operation to a full-scale mining operation; and evaluate the post-mining environmental restoration plan.

Jan 1, 2000

By T. T. Chen

This mineralogical study is based on samples from typical "wet" nickel laterites of humid tropical to sub-tropical regions. An in-situ nickel laterite sample from Goro and a transported laterite sample from Plaine des Lacs, New Caledonia, are predominantly limonitic. Two-thirds of the particles in the Goro sample are <10 um in size; they consist of skeletal goethite and serpentine, as well as minor amounts of talc, gibbsite, chlorite, quartz and clay minerals. The coarser grains are mainly Cr-spinel, serpentine, gibbsite and Mn oxide. Nickel occurs mainly in goethite, serpentine and Mn oxide; cobalt occurs in goethite and Mn oxide. The Plaine des Lacs sample is finer-grained and contains more Al and CO3, but less Mg and Si than the Goro material. The sample contains more kaolinite, chlorite, siderite and feldspar, but less serpentine and gibbsite than the Goro material. Nickel is detected mainly in goethite, serpentine, Fe-Mg silicate and Fe-Mn oxide. The Indonesian ore from Sorowako, as sampled from the reduction kiln feed containing some reverts, is predominantly saprolitic, with apparent particle sizes ranging from <100 um to > 1 cm. The sample of reduction kiln feed is rich in Mg silicates, Mg-Fe silicates and goethite, and exhibits complex alteration textures. The nickel contents vary from particle to particle. Nickel is present mainly in serpentine, olivine, chlorite and amphibole, and in subordinate amounts in goethite and Mn oxide. Cobalt is detected in the Mn oxide. Keywords: Nickel Laterite; Mineralogy; Nickel Carriers; Goro, New Caledonia; Plaine des Lacs, New Caledonia; PT Inco., Sorowaki, Indonesia

Jan 1, 2004

By Qingming Feng, Jinhong Zhang

A study has been carried out to apply fly ash as a high strength, water-resistant precast construction material through geopolymerization. Experiment results show that the working conditions such as water content, the concentration of NaOH, curing temperature, and curing time significantly affect the mechanical property of geopolymermatrix. Through optimization, an above-100MPa compressive strength has been achieved with the geopolymerization products. The optimum working conditions involves 10MNaOH concentration, 14–15% water content, and curing at 90 °C in an oven for 1 day or at ambient condition for 3 weeks. Adding Ca(OH)2 does not help to increase the compressive strength of the specimen.Water soaking tests show that the geopolymerization product has a very high water resistance without losing noticeable compressive strength, even after a 1-month soaking time. To elucidate the geopolymerization mechanism, microscopic techniques such as SEM/EDS (scanning electron microscopy and energy-dispersive X-ray spectroscopy), XRD (X-ray diffraction) and ATR-FTIR (attenuated total reflectance Fourier transform infrared) are also applied to investigate the microstructure, the elemental and phase composition of geopolymerization products. The findings of the present work provide a novel method for applying fly ash as a high-strength water-resistant precast construction material.

Aug 17, 2020

By N. Bahrani

Photogrammetry surveys were used to document a footwall slab failure that occurred at a surface coal mine located on the eastern slope of the Rocky Mountains. Photographs taken before and after the failure provided the pre- and post-failure geometry of the slope and the failed slab. A 2D finite element model was constructed using slope profiles. The model contained joint elements that represented the bedding surface upon which the slab slid and the model was used to analyze the footwall slope. The in situ stresses, rock properties and the bedding surface shear strength and stiffness properties are discussed. The process of mining out a valley and exposing a highwall was modelled. As expected, elastic valley rebound occurred in the model, but shear stress and shear displacement reversals along the slip surface were also observed. The modelling results provided new insight into shear strength degradation that occurs when the pit floor approaches and then passes a specific point in the highwall.

Jan 1, 2009

By Harold J. Schock

The cases of no auxiliary ventilation and ventilation with tubing were mathematically modeled, using a turbulent dispersion model. The scooptram that is used to load is modeled as a variable-speed, variable-strength source of pollutants moving in and out of the dead-ended drift. Model predictions are compared to experimental measurements. A parametric analysis was performed to determine the effect of exhaust pipe location and time spent out of the drift, as well as to determine if a relationship existed between CO2 and NO levels. It was concluded from this analysis that when modeling a load-haul-dump cycle, it is necessary to use a model that has the capability of predicting changes in source strength as well as source location. It was also determined that four relevant factors include effective heading height, apparent longitudinal diffusion coefficient, transverse concentration gradient at the face, and average dispersion width of the exhaust jet. As these factors change with heading geometry and ventilation configuration, they were determined experimentally, Carbon dioxide was used as a tracer to calibrate the model; since, knowing the fuel flow rate, it is possible to calculate CO2 production. The above four factors in the computer model were calculated using a regression analysis, comparing predicted local concentrations to measured local concentrations. The model was then verified after this calibration process using additional experimental results. With the calibrated model, it is possible to predict pollutant concentrations at any location in the heading using an engine map and the previously calculated flow field. A parametric analysis shows that the exhaust pipe location can have a significant impact on operator exposure to exhaust gases. It was also shown that NO concentration varies directly with C02 levels. Predictions using the dynamic model are contrasted with constant source strength (pollutant flow rate) results. An analysis of these predictions for computing time-weighted average NO shows the dynamic model predictions of operator exposure to this pollutant to be less than one-half of the value predicted using a constant source model.

Jan 1, 1981

St. Peter sandstone is an arenaceous sheet that covers large area in North America. The interest for St. Peter sandstone has been increasing due to the upward trend for hydrofracturing and the consequent need for fracking sand. This material is possesses very unique mechanical properties. On the one hand, it is brittle as characterized by an unusually high friction angle, up to 69°, and steeply curved failure envelopes. On the other hand, it is friable, possessing extremely low, and in most cases zero cohesion. The underground mines that are working under this condition are lacking the ground control techniques for this particular mining environment. The geotechnical properties of the St. Peter sandstone were examined using uniaxial test, triaxial test, porosity test, flexural strength test. This paper aims to investigate the effect of microstructure on strength properties, utilizing microscopic studies, index test (porosity, size distribution).

Feb 23, 2014

By E. Siami-Irdemoosa, S. R. Dindarloo

"Pareto analysis was used to investigate the failures database of a Hitachi EX1900 hydraulic shovel over one year of continuous operation. The hydraulic system and hydraulic links, hoses and piping were identified as the most critical system and subsystem, respectively. A three-parameter gamma distribution function was identified as the best fit for a probabilistic modeling of the time between failures (TBFs). This distribution was used in a Monte Carlo reliability analysis of the hydraulic system. Autoregressive integrated moving average (ARIMA), within the context of a time series analysis of the TBFs, was proposed as a viable alternative to the traditional technique of distribution fitting. The mean absolute percentage error (MAPE) metric was used to compare the two models. The MAPE value that resulted from the ARIMA was 66 percent smaller than that from the traditional technique in predicting the TBFs.Resumen ¦ Se usó análisis Pareto para investigar la base de datos de fallas de una pala hidráulica Hitachi EX1900 durante un periodo de un año de operación continua. Se identificó al sistema hidráulico y a los enlaces hidráulicos, mangueras y tuberías como el sistema y subsistema más importantes, respectivamente. Se identificó una función de distribución de tres parámetros gamma como el más apto para un modelado de probabilidades del tiempo transcurrido entre las fallas (Tabes por sus siglas en inglés). Esta distribución fue usada en un análisis de confiabilidad Monte Carlo para un sistema hidráulico. El promedio de movimiento integrado auto-regresivo (ARIMA por sus siglas en inglés), dentro del contexto de análisis de serie temporal de los TBFs, fue propuesto como una alternativa viable a la tradicional técnica de ajuste de distribución. Se usó el porcentaje de la media absoluta de error (MAPE) para comparar los dos modelos. El valor MAPE que resultó de la ARIMA fue 66 por ciento menor que el resultado obtenido con la técnica tradicional de predicción de TBFs."

Jan 1, 2015

By I. AITKENS

It is a common misconception that all yellow stones are topazes and that all topazes are yellow; but neither statement is true. The real topaz is a rather rare mineral, and a large number of yellow stones that masquerade as topaz are nothing more than yellow quartz, known as citrine, but almost universally called topaz. The true topaz is often called "Brazilian" topaz by the jeweler to distinguish it from yellow quartz; nevertheless, both terms are freely applied in trade to other yellow stones. Topaz is considered the most popular yellow stone for jewelry and is often used as the principal stone in brooches or pendants, especially in old-fashioned ornaments. However, many other species yield pretty yellow stones, some of which are far more numerous and less costly than the topaz.

Sep 1, 1931

By A. McLean, W. Q. Chen, W. Yan, M. Barati, Y. D. Yang

In order to maximally remove the harmful impurities phosphorus and reduce the loss of valuable elements from Si-based alloy for production of solar-grade silicon, thermodynamic properties of the Si-based alloy were studied. In this work a new model, the Molecular Interaction Volume Model (MIVM) derived from statistical thermodynamics, was successfully used in the Si-based and Si-Fe-based alloy. The calculation started from binary Si-Fe, Si-P and Fe-P systems, then the thermodynamic parameters of ternary systems could be derived based sub-binary systems. Using the activity coefficients of the elements in the Si-based alloys and the saturated vapor pressure of the pure substance of the components, mass fraction of P during vapor-liquid equilibrium can be calculated. The calculated thermodynamic parameters were compared with experimental data available in different publications, and it is found that the thermodynamic parameters calculated using MIVM model are in good agreement with the measured results. The calculated result shows that the mass fraction of phosphorus during vapor-liquid equilibrium of Si-Fe-P melt increases with the increasing phosphorus content and decreasing temperature. This is an important direction for experimental practice in vacuum or low-pressure EML refining of ferrosilicon for potential production of solar-grade silicon without significant vaporization loss of valuable element.

Jan 1, 2015