Search Documents

By N. A. Warner

Fundamental studies on the reaction of limestone or dolomite at high temperature with S02 are extended to the realm of large scale primary copper smelting. Whereas flue gas desulfurisation in the electric power utility industry is concerned with S02 concentrations normally less than 0.5 percent, high temperature smelting gases can have S02 levels approaching 100 percent. The reaction involved is very exothermic so proposals are made in this paper for returning the heat generated in sulfur fixation directly back to the copper smelting process. This integration leads to metal production with lower energy requirements than current technology. The anhydrite reaction product can either be disposed of locally with minimum adverse environmental impact or upgraded to a value-added product. It is assumed, of course, that no viable market exists to support sulfuric acid production.

Jan 1, 1996

By Yuanhong Qi, Xun Fu Wang, Tao Fu, Kunkun Cui, Yingyi Zhang, Jie Wang, Junmao Qie

With the sharp decrease of sulfide nickel resources, the nickel laterite is becoming more attractive as nickel oxide, nickel matte, and nickel-iron. This study investigated the mineral phase structure, chemical analysis, thermal properties, and element distribution characteristics of the rotten rock layer deposited in the Southeast Sulawesi Ophiolite Belt. The results show that the nickel laterite deposited in Southeast Sulawesi Island, Indonesia, belongs to the typical high-nickel and low-iron garnierite-type laterite. The concentrations of nickel and iron of the nickel laterite are 1.99 wt% and 17.55 wt%, respectively. The serpentine, olivine, clay, chlorite, hematite, and magnetite are the major minerals, and the pyroxene, actinolite, limonite, and chromite are the minor minerals in the nickel laterite in Southeast Sulawesi, Indonesia. Serpentine and olivine are the main nickel minerals with an average nickel concentration of 3.65 wt% and 1.73 wt%, respectively. The Fe and Ni have homogeneity and symbiosis in the serpentine and olivine, and their concentrations are often positively correlated.

By A. S. Moore

The Bureau of Mines is doing research and development work on removing acid-gas impurities from synthesis gas made directly from coal. Since conventional gas scrubbers, packed towers and bubble-cap columns, are expensive to construct and difficult to operate with viscous solutions, one aspect of the work was developing a compact, agitated, gas-liquid contactor for use with concentrated absorbents. The efficacy of the agitated contactor for absorbing carbon dioxide in diethanolamine increased with increasing solution rate, turbine speed, diethanolamine concentration, and carbon dioxide concentration in feed gas, and with decreasing liquid-gas ratio. It was unaffected by pressure between 200 and 300 p.s.i.g. and little affected by temperature between 115 and 190° F.

Jan 1, 1961

By Earle Faig

Earle Faig Along with other transportation modes, the barge industry will be greatly affected by trends in domestic coal production. Traditionally, coal has been one of the major commodities moved by barge. Now, because of events in the international energy market, coal is finally getting the recognition it deserves as a major component of the country's energy program. Perhaps even more significantly, a series of events has caused other countries to turn to the United States as a source of coal. Although the outlook for coal demand is optimistic, it will be greatly influenced by the ability of the transportation sector to handle the additional traffic. Because of its long experience in moving large quantities of coal, the barging industry is in an excellent position to capitalize on coal's increased popularity. A brief description of the barging industry should facilitate the discussion of coal as it relates to that industry. Barge companies operate on a river system that is over 40 Mm (25,000 miles) long. It includes the East and West Coasts and the Mississippi River System comprised by the Allegheny, Monongahela, Kanawha, Ohio, Illinois, Missouri, Tennessee, Cumberland, Arkansas, Warrior-Tombigbee, and Mobile Rivers, and some smaller tributaries. The Gulf Intracoastal Waterway stretching along the Gulf Coast from Brownsville, TX, to Apalachicola, FL, also is considered part of the inland waterway system. Approximately 1,800 companies operate on the inland river system and have a combined fleet of about 4,400 towboats and 28,000 barges. The fleet of towboats represents 4.8 GW (6.4 million hp) of power. The towboats comprising this fleet vary in size from a small harbor boat to a large line haul boat with 7.5 MW (10,000 hp) of power. The choice of size and power of the boat depends on a number of factors, including the size of the river and operational constraints, such as lock size, river-current rate, and water level. The choice also depends on the tow size. A single tow on a river capable of locking through 15 barges at a time handles up to almost 20 kt (22,000 st), whereas a tow on the lower Mississippi, which has no locks, can accommodate up to 41 kt (45,000 st) of cargo. Because the quality of coal is not typically damaged by exposure to the elements, it is usually moved in open hopper barges, although covered barges are used occasionally. The most frequently used size is the jumbo barge that measures 59 m (195 ft) long by 11 m (35 ft) wide by 4 m (12 ft) deep and can handle up to 1.4 kt (1,500 st) of coal. Advantages of Barge Transportation Barging offers several inherent advantages in transportation of bulk commodities like coal. First, barges can carry large quantities of product. A single jumbo hopper barge can handle 1.4 kt (1,500 st) of cargo while it takes 15 91-t (100-st) capacity rail cars or 57 trucks hauling 24 t (26 st) each to move an equivalent amount of cargo. Thus, barges can move more tonnage with less equipment than competing forms of transportation. Second, barging offers the most fuel efficient means of transportation. Less energy is required to push a load over water than to pull a similar load over land. The amount of pollution attributable to barge traffic is minimal because barges consume less fuel. Third, barging is an inexpensive form of transportation. The inland waterway industry transports about 12% of the nation's freight for about 2% of the total freight bill. This can be attributed to competition between the large number of companies on the river system and competition with other transportation modes. Fourth, barging is an environmentally safe method of transportation. Inland river routes expose fewer urban areas to hazardous substances than rail or truck. And barge spills occur less frequently than rail or truck spills. The industry does pose some disadvantages. The waterway system is constrained by the natural river network, so barges cannot travel on the most direct straight-line route. This means that barging is usually an incomplete form of transportation requiring interface with truck or rail. The industry's market is limited to those geographical areas that are located on or near the rivers. In addition, it is a time-consuming transportation mode, making it impractical for many types of commodities.

Jan 10, 1982

By J. H. Swisher

ALUMINUM deoxidation equilibrium in liquid iron has been the subject of many investigations. Sawamura and Sano1 have written a critical survey of the literature on this subject and consider the data of Gokcen and chipman2 and of d'Entremont, Guernsey, and Chip-man3 to be most reliable. The present study was undertaken to check these data and extend the range of the experiments to lower temperature. The experiments consisted of equilibrating 5-lb Fe-Al melts with recrystallized alumina crucibles at 1580o + 10oC, and analyzing the solidified ingots for aluminum and oxygen. The electrolytic iron stock contained 100 ppm C, 20 ppm 0, and trace amounts of other elements.* The stock was induction-melted in an atmosphere of 5 pet H2 in argon to attain equilibrium between the melt and the crucible. The temperature was measured with a W, 3 pet Re/W, 26 pet Re thermocouple, and the equilibration time was about 4 hr. The results are plotted in Fig. 1 along with curves obtained from the data of d'Entremont et al.,3 for temperatures of 1740o and 1910°C. The present results can be seen to be consistent with the previously reported high-temperature data. The reaction under study is AI2O3 (s) = 2 Al (l) +3O [1] for which the deoxidation product is Kl =[% Al]2 [%O]3 [2] (Under the experimental conditions, Fe A12O4 is not expected to form.4) In Fig. 2, values of log Ki evaluated at 0.01 pet A1 are plotted against 1/T, using data obtained from all the investigations under consideration. The deoxidation product is plotted in Fig. 2 in lieu of the equilibrium constant (normally obtained by evaluating Ki as pet A1 — 0) because of the uncertainty involved in extrapolating to zero concentration. The difficulty in extrapolating the present data for 1580°C is apparent curvature in the log Ki vs pet Al plot. This curvature is perhaps due to the uncertainty in oxygen analysis for concentrations of 5 ppm and below. For the data of Gokeen and chipman,' the extrapolation is also difficult because of experimental scatter. The line drawn through the points plotted in Fig. 2 may be represented by the equation:

Jan 1, 1968

To enable ammonium nitrate-fuel oil (AN-FO) to be used on an equal weight basis with nitroglycerine explosives, smaller diameter bore holes became necessary with consequent modifications to drill steel and burden on holes. Detonation of AN-FO in small diameter holes proved successful both with and without primer charges but some alterations were required to adapt anoloders to the smaller holes.Important factors in training all operators in the new charging method were the retention of improved fragmentation, avoidance of excessive overbreak and keeping wall rock dilution to an absolute minimum. The successful storage of ammonium nitrate in climatic conditions with daily temperature fluctuations above and below the critical 90°F has been achieved.INTRODUCTIONTechnical aspects of ammonium nitrate-fuel oil (AN-Fa) blasting agent are well covered in recent literature. This paper deals primarily with the manner of its introduction as the principal explosive underground at Great Boulder Gold Mines Ltd. and with the many problems encountered in the process. Following reasonably successful experimental firings in June 1962', using granular ammonium nitrate and an anoloder, permission was granted by theWestern Australian Mines Department to carry out test work in selected areas of the mine. The permit allowed for fuse firing only, and for a mixture of AN-Fa containing between 5t and 6 per cent fuel oil, with an adequate primer.The use of AN-Fa on an equal weight basis with nitroglycerine explosives, involved smaller diameter holes with alteration to ground burden and modification to drill steel.Initial tests indicated that it was apparent that AN-Fa could not replace gelignite on an equal weight basis if the...

Jan 1, 1965

By Tania Schmid, Marco Portal Valdivia, Sandra Nowosad

Today’s mining industry faces rapid transformation driven by automation, climate responsibility, and ESG demands, requiring more than technical expertise. Future mining engineers must blend engineering excellence with key human skills such as communication, leadership, resilience, empathy, adaptation to change, curiosity and lifelong learning. Based on two recent surveys, one to senior leaders with over ten years of experience in the mining industry and a second, focused on understanding the perceptions of young professionals, this paper explores which skills become core competencies by 2030 for navigating complexity, leading responsibly, and enabling sustainable transformation. Furthermore, it also examines how educational institutions can adopt strategies to foster the development of these critical skills, preparing future mining talent for evolving challenges.

Feb 22, 2026

By Francis X. Cannaday

The purpose of this investigation was to find whether the moduli of elasticity obtained were the same for the following methods : ( 1 ) Deformation of a borehole in a prism subjected to uniaxial stress ; ( 2 ) deflection of a thin beam of uniform cross section uniformly loaded ; ( 3 ) sonic - pulse velocity measurements , and ( 4 ) strain measurements on a prism under uniaxial stress . The rock tested was chosen for its good elastic behavior and relatively good homogeneity and elastic isotropism . The same rock was used for all methods . Results indicate that for given environmental and stress conditions the moduli obtained by each of the four methods check one another within the limits of experimental error and that the differences introduced which are characteristic for each method are smaller than physical variations within the rock tested .

Jan 1, 1964

By Dong Yang, Jicai Han, Xiaoshuang Guo, Tichang Sun, Zhengyao Li

Straw charcoal was used as a novel reductant in the co-reduction roasting of laterite ore and red mud. The influence of the reductant dosages, co-reduction temperature, and co-reduction time were investigated. Results showed that a powdered ferronickel product of 1.81wt.% nickel and 81.40wt.% iron was obtained under straw charcoal dosage of 15wt.% and roasted at 1250 °C for 80 min. The corresponding recovery of nickel and total iron were 97.21wt.% and 98.87wt.%, respectively. The performance of straw charcoal was also compared to that by the conventional coke reductant. Results showed that ferronickel particles using straw charcoal were larger in size than coke, mainly due to the lower S (0.14wt.%) and ash content (3.80wt.%), which could not hinder the agglomeration of the ferronickel grains, and lower melting point that producing liquid phase and promoting ferronickel particles growth. In addition, the gasification reactivity of straw charcoal is better than that of coke, which is beneficial to the iron oxide reduction and the recovery of iron. To conclude, straw charcoal is a promising reductant for the co-reduction of laterite ore and red mud in coal-deficient areas.

Aug 12, 2021

By H. E. Gross

A plausrsle method of drilling beyond the continental shelves is set forth with limitations of the method. The continental shelves comprise the water-covered portions of land masses out to 600 ft. of water, or roo fathoms. The problems and possibilities of drilling beyond this depth are discussed in this paper. Introduction Much attention is being given the problem of developing petroleum beneath the open sea. Geophysical surveys have been made 26 miles offshore1 from the continental United States, and onco offshore ownership is established it is likely that there will be drilling for oil on the continental shelves. More than two years ago the author presented the means for drilling in deep water.2 at the fall meeting of the Petroleum Division of the AIME at Los Angeles. His concepts then were based on the use of rigid foundations suitable for drilling in water up to 600 ft. deep. The present paper suggests a method for drilling in deeper water. Possibilities and Problems of Drilling beyond the continental shelves It being conceded that because restricted deep-water portions of the hydrosphere might contain oil in commercial quantities, and that at any rate it is pertinent to know more of the nature of the lithosphere beneath the hydrosphere, the possibilities and problems of drilling beyond the continental shelves should be set forth. Drilling in open water would offer few if any advantages over drilling on land. These are: 1. The ocean transportation is available to deep-water drilling sites, and extensive pipe lines and roads are unnecessary. 2. Refinery facilities and markets perhaps are established on the near-by shore where adjacent fields on land are nearing depletion. 3. There is freedom from jungle pests and tropical diseases. 4. Competitive drilling is less likely. 5. Extensive areas attractive for development arc not yet under lease or concession. Disadvantages are great and numerous: 1. Storm hazards from wind and wave. 2. Expensive foundations, either rigid or floating. 3. Shutdown times because of weather. 4. Marine Regulations of Federal Bureaus in addition to customary regulations on land. 5. Frequent difficulty in moving men and materials to and from drilling platforms. 6. Extra precautions required in open sea. For drilling in water more than 500 or 600 ft. deep, rigid foundations2 become too costly, and floating foundations must be used, and they must meet the following requirements:

Jan 1, 1947

By H. E. Gross

A plausrsle method of drilling beyond the continental shelves is set forth with limitations of the method. The continental shelves comprise the water-covered portions of land masses out to 600 ft. of water, or roo fathoms. The problems and possibilities of drilling beyond this depth are discussed in this paper. Introduction Much attention is being given the problem of developing petroleum beneath the open sea. Geophysical surveys have been made 26 miles offshore1 from the continental United States, and onco offshore ownership is established it is likely that there will be drilling for oil on the continental shelves. More than two years ago the author presented the means for drilling in deep water.2 at the fall meeting of the Petroleum Division of the AIME at Los Angeles. His concepts then were based on the use of rigid foundations suitable for drilling in water up to 600 ft. deep. The present paper suggests a method for drilling in deeper water. Possibilities and Problems of Drilling beyond the continental shelves It being conceded that because restricted deep-water portions of the hydrosphere might contain oil in commercial quantities, and that at any rate it is pertinent to know more of the nature of the lithosphere beneath the hydrosphere, the possibilities and problems of drilling beyond the continental shelves should be set forth. Drilling in open water would offer few if any advantages over drilling on land. These are: 1. The ocean transportation is available to deep-water drilling sites, and extensive pipe lines and roads are unnecessary. 2. Refinery facilities and markets perhaps are established on the near-by shore where adjacent fields on land are nearing depletion. 3. There is freedom from jungle pests and tropical diseases. 4. Competitive drilling is less likely. 5. Extensive areas attractive for development arc not yet under lease or concession. Disadvantages are great and numerous: 1. Storm hazards from wind and wave. 2. Expensive foundations, either rigid or floating. 3. Shutdown times because of weather. 4. Marine Regulations of Federal Bureaus in addition to customary regulations on land. 5. Frequent difficulty in moving men and materials to and from drilling platforms. 6. Extra precautions required in open sea. For drilling in water more than 500 or 600 ft. deep, rigid foundations2 become too costly, and floating foundations must be used, and they must meet the following requirements:

Jan 1, 1947

By Valeh Aghazadeh, Shima Barakan, Mina Soleymani, Ehsan Bidari, Morovvat Faridazad

Molybdenite is the most important molybdenum concentrate, which is mainly recovered as a by-product from porphyry copper deposits. Due to the low efficiency of purification processes such as flotation in the reduction of copper content of molybdenum concentrate to a standard level (i.e., less than 0.5 wt.%), further purification by a hydrometallurgical method is required. Although different types of chemical reagents were found to be effective in the leaching of copper minerals from molybdenum concentrate, the mechanisms of these processes remain largely unexplored. In this study, optimal conditions for maximum copper leaching (> 99%) were obtained at the concentration of HCl = 1 M, FeCl3 = 0.5 M, CuCl2 = 0.05 M, CaCl2 = 0.5 M at 75 °C, 500 rpm, and S:L = 1:10 during 60 min. CuCl2 was identified as the most effective leaching reagent for copper dissolution in agreement with Visual MINTEQ model results due to the formation of various types of copper chloride complexes. Furthermore, the electrochemical behaviors of FeCl3, CuCl2, and CaCl2 reagents before and after the leaching process were investigated by the cyclic voltammetry technique. The results of cyclic voltammograms at different scan rates verified the presence of copper chloride complexes, and ferric ions as the oxidizing reagents for better dissolution of copper sulfides. Based on kinetic study results of shrinking core models, both chemical and diffusion reactions controlled the copper leaching process with an obtained activation energy of 33.56 kJ/mol. For recovery of the leached copper, the precipitation process was done by the addition of Na2S at 45 °C, S/Cu = 1, and pH = 9.

Dec 26, 2022

By A. Rajoria

A dynamic process model for predicting the fluidized bed roasting of copper concentrates with high arsenic content is presented in this work. Mass and energy balances were performed based on roasting mechanism derived from thermodynamic data of species. The reaction rate data, obtained from pilot plant studies on major reactions, were used in tuning the kinetic parameters of the model. DEAS, a dynamic simulation package, is used in setting up the fluidized bed roaster plant model. The effect of process parameters such as concentrate feed rate, concentrate composition, airflow and cooling water rate on the temperature and conversion of roasting reactions are analyzed. The plant model captures the highly transient conditions occurring during the plant start-up, shutdown and other process perturbations. The application of this model in constructing a virtual plant environment for validating the operating procedures and operator training is presented.

Feb 23, 2014

By D. A. Paice

A power supply to operate fluorescent or mercury vapor lamps from 300 volt dc coal mine trolley wires has been developed for the Bureau of Mines. A high frequency regulated inverter unit incorporates ballasts for a mix of lamp loads up to 650 watts. For 600 volt trolley systems an additional power converter unit was developed to step down the dc voltage to 300 volts for the inverter unit. Both units have operated in a working coal mine for over 12 months without need for servicing. The lamp load in these tests included two 100 watt mercury vapor head lamps and six 75 watt fluorescent lamps.

Jan 1, 1979

By Shahab Alizadeh, Ahmad Khodadadi Darban, Mehdi Mohseni, Mahmoud Abdollahy

This study probed the selective separation of lanthanum and yttrium in a nitrate medium in the presence of aluminum and calcium impurities using di-(2-ethylhexyl) phosphoric acid (D2EHPA). The factors studied in a central composite design (CCD) included extractant concentration, pH, concentration ratio of total impurities to rare earth elements, and interaction of these three factors. The extraction mechanism and types of extracted metal-containing species were delineated by the slope analysis method. The obtained thermodynamic data showed that lanthanum and yttrium extraction by the D2EHPA extractant was exothermic. The extraction of both rare earth elements was accompanied by an entropy reduction. The negative magnitude of ΔS in yttrium extraction reaction suggests stronger D2EHPA-Y(III) complexation relative to La(III). As entropy decreased and enthalpy increased, the extraction process became unspontaneous. Using the proposed flowsheet, lanthanum and yttrium products with > 90% purity were obtained.

Aug 10, 2021

By Frank G. Horino

The Bureau of Mines studied the uniaxial compressive strength of model rock pillars as a function of the angle and spacing of noncohesive planes of weakness. The model pillars were prepared from NX 2-l/8-inch diameter drill core of limestone, sandstone, and granite, and the planes of weakness were diamond saw cuts ground flat and smooth. The angle of the planes of weakness, measured from the horizontal, varied from zero to 57° in approximately 15° increments. When two planes of weakness were used, the thickness-to-diameter ratio of the wafer was 1/4, 1/2, and 1, Approximately 400 model pillars were tested in uniaxial compression. The results indicate that the uniaxial compressive strength of model pillars decreases rapidly as the angle of the plane of weakness increases from 30° to 57°, and that the spacing of these planes of weakness has only a minor effect on the strength. The effect of the number of horizontal planes of weakness, with a spacing of 1/4 and 1/2 of the diameter, upon the compressive strength of model pillars was also investigated. These results indicate that as the number of planes of weakness increases the compressive strength of the pillar decreases. Normalizing the data provides useful estimates of model pillar strengths for any rock type.

Jan 1, 1968

By M. W. Bates, A. L. Mular

This paper, based on work carried out at Queen's University, describes the development and use of mathematical models of the parallel cyclone classifiers being used in the Strathcona mill of Falconbridge Nickel Min.es Ltd.

Jan 1, 1971

By I. S. M. K. Ilankoon

In heap leaching the transport of the acid from the drippers to the surface of the ore particles is a major factor in the overall performance of a heap. This flow behavior is complex as the flow is unsaturated and occurs along a tortuous set of inter-particle channels and connections. Previous modeling of this system has used equations from oil and ground water flow to model these systems, but the applicability of these models with the larger particles found in typical heaps is suspect as these systems are not necessarily capillary dominated. In particular, as the characteristic particle size goes from below to above a few centimeters, the flow changes from capillary to gravity dominated. This means that typical heap leaching heaps cover this interesting, but complex, transitional fluid flow regime. In this paper a set of experimental studies of this flow, including PEPT (positron emission particle tracking) based tracer experiments, highly accurate liquid holdup measurements and axial dispersion experiments using salt tracers will be presented. In this study, flow through mono-dispersed particle beds was carried out. In particular, the hysteresis in the liquid holdup as the liquid flow rate into the particle bed is varied is investigated, since this hysteresis means that the relationship between flow rate and holdup is history dependent, an effect not included in models currently used to describe fluid flow in heaps. A theoretical model that describes this hysteresis will also be presented. Keywords: heap leaching, hydrometallurgy, modeling

Sep 1, 2012

By Ben Burger

This paper describes the design, the first three years of operation and optimization of a large, single stage SAG mill at Minera Yanacocha?s Gold Mill facility located in northern Peru. The Gold Mill was commissioned in March 2008 with a 32? x 32? EGL, 16.5MW single stage SAG mill, to process 5 million tonnes per annum high grade oxide Au/Ag ore. Operational control, feed size distribution, grinding media, mill liner, grate and pulp lifter optimisation have allowed the mill to operate 15-30% above design throughput rates, but with a product P80 coarser than design. As part of the optimization, full grinding circuit surveys were conducted. Historical operating data and survey data were analyzed and used to evaluate possible circuit changes and determine alternative operating strategies. A number of changes were implemented which allowed the SAG mill to operate similarly to a large ball mill and achieve finer mill product that was closer to design. This paper summarizes life to date data analysis and improvements made by Minera Yanacocha as well as the grinding circuit optimisation study conducted by Metso Process Technology and Innovation.

Jan 1, 2012

By H. M. Harris

The Bureau of Mines investigated chlorination of domestic ilmenites in a fluidized coke bed at temperatures of 950° to 1,150° C. Objectives were to develop an effective process for producing TiC14 suitable for TiO2 pigment and to reduce pollution by collecting and treating waste byproduct chlorides. The reactor for these tests was a 10.2-cm-diam quartz tube heated externally by electrical resistance heaters. It contained coke beds of from 35.6 to 82.5 cm in depth that were fluidized by 13 to 25 l/min of chlorine. Ilmenite concentrate powders were introduced at the bottom of the fluid-bed reactor, using the chlorine gas stream as a carrier. Test results showed that greater than 90 pct of the ilmenite reacted at optimum conditions and recovery of TiC14 ranged from 95 to 99 pct of stoichiometric. A temperature-controlled cyclone was used to remove high-boiling-point chlorides such as MnCl2, MgCl2, and FeCl2, and also collected fine unreacted ilmenite and coke dust. Impure TiC14 and FeC13 were separated by collecting the, iron chloride in a condenser con-trolled at 200° C. Titanium tetrachloride vapor was cleaned by passage-through a salt-column filter followed by condensation in water-cooled and refrigerated condensers. Liquid TiC14 was purified further by well-known industrial methods to meet specifications for pigment-grade chloride. Integrated tests were conducted in which chlorine, produced by dechlorination of FeC13 with oxygen, was recycled and used directly in a fluidized-bed chlorinator.

Jan 1, 1976