Search Documents

By X. Xu

This paper presents the research on comprehensive recovery of copper, gold, silver and iron from tailings from high-intensity magnetic separation in Tonglushan Mine. By comparison of experimental results of three flowsheets?regrinding of tailings-conventional sulphidizing flotation, water heating enhanced sulphidizing flotation and acid leaching-sulphidizing precipitation flotation, it is concluded that regrinding of tailings-conventional sulphidizing flotation flowsheet has the best economical and technical performance and practicability. Regrinding and using the mixture of sodium hydroxamate and sodium xanthate are two of the notable technical characteristics of this best flowsheet. The system for comprehensive recovery of tailings has been put into production. It not only can recover the valuable minerals from tailings in Tonglushan Mine, but also can reduce the environmental pollution, resulting great economic and social benefit.

Jan 1, 2014

By Leo J. Vogel, E. D. Hummer, David J. Akers

INTRODUCTION An efficient refuse-disposal system is a necessary part of the modem cleaning plant. The large-scale refuse system and disposal area, engineered for the lifetime of the plant, has become more important due to the greater tonnages of refuse produced from increased quantities of mechanically mined and prepared coal. Laws and increased government regulations have affected the design and operation of disposal systems. THE EFFECT OF MINE AND PLANT OPERATION Refuse disposal starts at the mining face. The mining system, the type of roof support, the machinery used, and the degree of discipline at the face contribute to the amount and type of refuse that must be removed through the disposal system. Economies gained through modification of the mining system or mining machinery may be partially offset by increased dilution of the mined coal with impurities from associated rock formations. In some cases the change in the mining system and equipment has reduced the dilution. In all cases the ratio of impurities that must be removed from the raw-coal feed to the plant not only affects the maintenance and

Jan 1, 1979

By K. Ebrahimi-Nasrabadi

The dependence between the extent of conversion of cryptocrystalline magnesite to caustic magnesia was studied experimentally in the temperature range of 400?1200 °C and for calcination times up to 8 h. A TGA?DTA analysis showed that decomposition begins at temperatures as low as 340 °C and is completed at 600 °C. Measurements of specific surface area (SSA), iodine adsorption number (IN), crystallite size, and loss on ignition were carried out to characterize the product quality. It was found that while all the parameters are dependent on the extent of calcination, densification of the product caused by grain coarsening affects their final values. As a consequence, SSA and IN went through a maximum with time. The study showed that high quality caustic calcined magnesia can be produced in a narrow range of temperature (600?650 °C) and time (1?4 h). Medium quality caustic calcined magnesia can be made within a wider range of parameters.

Aug 1, 2013

By A. D. Randolph

Comminution represents one of the major costs of mineral recovery from low-grade ores. Efficient mineral recovery in a typical low-grade ore grinding-flo¬tation process depends on grinding the ore small enough to liberate mineralization without producing excessive slimes, which would result in higher power and flotation reagent costs. Size criteria for efficient grinding should be stated in terms of the distribution of mineralization sizes, but as the mineralization-size distribution is difficult to determine, less desirable criteria of absolute particle-size distribution (PSD) are used in practice. Thus, there is considerable incentive to be able to analyze and predict the PSD performance of grinding circuits for control and optimization of the process. Any realistic model of a grinding circuit must account for recycle of oversize material; such oversize recycle adds to the total mill load and limits total production rate. Simulation of such closed-circuit operation to study grind factors affecting total throughput can be done in a straightforward fashion provided recycle calculations can be added to an accurate input-output model of PSD in the grinding mill itself. Such a total simulation of mill performance is of obvious practical value in assessing the practicality and benefits of various over-all mill control schemes and/or modes of operation. For example, considerable interest has been shown in the development of continuous on-line particle-size sensors and such instruments should be an operating reality in a few years. A total closed-circuit PSD model of this type would be invaluable in the utilization of, and in predicting the pay-out from, such an on-line particle-size sensor. The purpose of this paper is to present a new approach to the development of an input-output PSD model of a grinding mill. The model is continuous in the par¬ticle size coordinate, L, and is based on the principle of a particle population balance along the particle size coordinate. Most previous studies of the grinding unit operation attempt to relate power

Jan 1, 1971

By J. N. Cox

Coal preparation is based on the properties of noncombustable materials (impurities) in coal being different from the organic constituents. The most commonly used property difference is density, via its affect on settling rates; and either gravitational or centrifugal forces can be used to remove impurities. However, examination of various particles settling rate correlations shows that at smaller sizes, particle drag becomes a very important factor. Classification, based on differential settling rates, becomes impractical and some property other than density must provide the basis for fine coal cleaning. Froth flotation and agglomeration employ differences in surface properties to clean coal. These methods are very successful except that the oxidized surface of a pyrite particle is somewhat hydrophobic and will tend to be collected with the organic portion of the coal. Surface property cleaning techniques have not been very effective in rejecting sulfur, except for two-stage flotation.

Jan 1, 1984

By Xiao min Zhou, Yan Xu, Hongzhen Liang, Xiaonan He

"With the increase of shaft excavation depth, the thickness of the shaft lining increases sharply. It is difficult to reduce thickness of lining effectively by improving high-strength concrete performance. The concept of the New Austrian Tunneling Method (NATM) is that surrounding rock plays a certain role in tunnel support. The solution should be to find the correct relationship between shaft lining thickness and rock strength, which is related with the interaction between the surrounding rock and concrete lining. The plane strain mechanics model is introduced to calculate lining thickness. Shaft lining design of Cixi Colliery in China is completed with the mechanics-based method proposed in this study. The lining design is verified through numerical simulation and field monitoring. The simulation results show that the maximum mises stress is located at the inner edge of the shaft lining. The increase of lining thickness cannot effectively reduce concrete grade. The monitoring results indicate that a lining design thickness of 900mm with C60 concrete, is safe and reliable in the shaft over 1000metres.This analytical design method can well be referenced in similar deep shaft projects.INTRODUCTION The New Austrian Tunneling Method (NATM), thought to have helped revolutionize the modern tunneling method, is the most extensive design philosophy and construction principle in today's tunnel engineering. It began to attract attention in the 1960s based on the work of Ladislaus von Rabcewicz, Leopold Müller, and Franz Pacher in Austria[1]. NATM was originally developed for tunneling in depth and in high situ-stress conditions in the Alps. The history of sequential excavation was reviewed, which highlights the progress of tunnel design and construction in Europe after NATM[2]. Structural conditions were introduced into the equilibrium of tunnels in NATM, and the additional force was estimated to stabilize the excavation of the tunnel[3].From the perspective of applied mechanics, there was no accuracy theory to explain the interaction between the tunnel structure and the surrounding ground. Numerical calculation is an effective means to study the basic mechanism of tunnel excavation[4].Based on two-dimensional modeling approaches in the past, such as NATM and other derivatives, a three-dimensional model was studied to"

Jan 1, 2019

By Muhammad I. Kabir

The streamline method of recovery prediction reduces a two-dimensional problem to a bundle of one-dimensional ones. This paper presents the development and application of a novel scaling technique which, when used with a streamline model, causes s bundle of one-dimensional problems to further reduce to a single one-dimensional calculation. The one-dimensional calculation accounts for chemical-rock interactions and the streamline model for areal sweep. The scaling technique significantly reduces computation time, is readily modified to desk-top calculations, and can be applied to both absorbing and reacting species. The work was sponsored by the Interior Department's Bureau of Mines.

Jan 1, 1984

By J. S. S. Allwin Ebinesar

The bioremediation of zinc was carried out using Pseudomonas alcaligenes, a Gram negative heterotroph. The parameters such as pH, bacterial cell number, initial metal concentration, and interaction time on the biosorption of zinc were studied. The maximum zinc uptake was found to be about 95% at pH 5 and biomass loading of 2.7x1010cells/mL. The biosorption isotherm for zinc exhibited Langmuirian behavior and the Gibbs free energy of biosorption was determined to be -31.2 kJ/mol, indicative of coordination of zinc with the functional groups on the bacterial surface. The adsorption kinetics followed a pseudo-second order equation. FTIR and EDAX studies confirmed the interaction of zinc with the biomass. The mechanisms of metal-microbe interactions are discussed.

Sep 1, 2012

By W. C. Meyer

Surface tension and its control are important in the concentration of ores by froth flotation, both in terms of producing the proper bubble size distribution and to render the ore surface of interest hydrophobic such that adhesion to a bubble will take place. The influence a substance has on surface tension has traditionally been measured using static, equilibrium techniques. Yet many applications such as flotation involve rate-related effects of surface tension where equilibrium values are not reached. In the time frame of 1 - 300 seconds, aging effects have been noted for bubbles formed in dodecylamine acetate solutions; a slow decrease in surface tension occurs until an equilibrium value is reached, as studied by Finch and Smith (1972). Since stationary bubbles do not exist in flotation cells because of the turbulence generated by agitation and aeration, it is more likely that the chemical composition of the bubble is determined during its formation, under dynamic conditions. The chemical composition is extremely important because the induction time required for a particle-bubble entity to collide and adhere to each other is augmented by favorable surface tension (wetting) proper- ties between the surface of the particle and the bubble air-water interface or envelope, as considered by Mackenzie and Matheson (1963). Finch and Lyman (1976) have established that the probability of a "permanent" attachment taking place during this contact time is aided by the ability of an oil droplet (viz. bubble) to relieve non- equilibrium surface tension effects which are involved in the water-thinning process. This Maragoni effect, or surface elasticity, can be considered in the context of particle agglomeration addressed by Kao and coworkers (1975). Water drainage leads to the formation of a collector-frother meniscus appearing between the colliding entities, arising from their combined partial immiscibility in the water phase and promoted by hydrophobic bonding within the interface. Together they constitute a liquid bridge whose force of attraction drawing the particles together is proportional to the interfacial tension existing between the water phase and liquid bridge. This adhesive force shows an approximate linear decrease with separation distance until rupture occurs, that is, FX = Fmax (1 ? X/Xr) (1) for a distance of separation X and rupture distance G. The greater the surface elasticity of the bubble, the greater will be the rupture distance and the better will be the force of adhesion. Since van den Tempel (1965) has related surface dilational properties of bubbles to the elasticity, E, of the film as

Jan 1, 1983

By Liu Jin

"In order to reduce the dosage costs and increase the economic benefits of a full floating process in a low grade complex multi-metals W-Mo ore, based on the study of the magnetic characteristics of the main gangue minerals, a joint process by magnetic separation and floatation technology is adopted. The first step of the flowsheet is to recover magnetite by magnetic separation, then remove the magnetic gangues by high gradient magnetic separation (HGMS) and finally recycle the W-Mo from the magnetically separated tailings by flotation. Results of the lab experiment show that in comparison with the full flotation process, the floatation feed tonnage of the combined flowsheet are only 46%. The grade and the recovery of Mo in the rough Mo-Bi concentrate is similar with the original one while the WO3 in the tungsten rough concentrate is increased from 3.85% to 6.64%. The dosage costs are reduced by 53%. The new process can significantly improve the plant economically. INTRODUCTION With the continuous exploitation of scheelite resources, the easily obtained resource is gradually depleting. The ""lean, fine and complex"" scheelite resource has become the main research object of tungsten beneficiation (Lou et al., 2010) (Xiao et al., 2013). The passive situation of tungsten beneficiation can be reversed by enhancing technological innovation and investment in science and technology, changing the business philosophy and mode of production, optimizing the process structure and process conditions, improving various technical indexes and reducing production costs of reagents, which will maximize economic benefits (Jiang et al., 2012 ) (Zhu et al., 2016). A polymetallic deposit of tungsten molybdenum bismuth original process adopts a full flotation process. With the expansion of stope mining, the content of valuable metals in the ore continues to decrease, resulting in a high cost per ton of concentrate produced and a low output value (Li et al., 2015)."

Jan 1, 2018

By Hongqiang Wang, Qingliang Wang, Eming Hu, Zhiwu Lei, Fang Hu, Rui Zhang, Wei Hou

Pyrite, a mineral associated with uranium ore, is closely related to uranium leaching. In this study, Ozone micro-nano bubbles (OMNBs), as an environmentally friendly advanced oxidation technology, were used for the first time to oxidize pyrite under experimental conditions to improve the leaching rate of uranium. A laboratory-scale agitation leaching experiment of pyrite was carried out with a pH of 1.0–3.0, gas flow of 1–3 L/min, ozone generation rate of 0.55–2.22 mg/s, and pyrite concentration of 0.1–5.0 g/L for 1 h. By adding three different co-oxidant: Mn(II), Mn(IV), and Fe(III), it was found that only Mn(IV) increased the oxidation rate of pyrite by 21.7%. The results of the scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) show that the formation of Fe(III)-O film on the surface of the ore suppresses the oxidation rate of pyrite to a certain extent. Pyrite can be rapidly oxidized up to 57.6% by OMNBs, which is beneficial to uranium leaching. This method is expected to be used for in situ acid leaching of uranium with OMNBs injected into the ground.

Jan 3, 2022

By Peter Grandone

"INTRODUCTION The Bureau of Mines, recognizing the importance of knowing the evapor¬ation losses of aviation gasoline as larger quantities of this material must be stored, has made studies at a large refinery in the Texas Panhandle area during the past 13 months to determine the magnitude of the losses, by evaporation, under different storage conditions. Proper storage of aviation gasoline is very important, not only because large supplies are being stored for military use but because the specifications to which his fuel must conform are very rigid. Aviation gasolines that conform present-day specifications are blended from base-gasoline stocks (in some instances relatively pure hydrocarbons), each of which has different physical and chemical characteristics. Consequently, partial loss of any one of the more volatile components from the blended fuel results not only in material loss of the blended fuel but also may affect the characteristics or performance of the gasoline. One characteristic that has considerable influence or the vaporization tendency of gasoline is vapor pressure; and although the vapor pressure of aviation gasoline usually is lower than that of average commercial motor fuel, the quantity of certain components having relatively higher vapor pressure is greater in aviation gasoline, so that under prolonged storage the evaporation loss of these components may be appreciable."

May 1, 1943

By Juan E. Rassmuss

Durante mucho tiempo la explotación del azufre en el interior del Perú, ha sido de manera regular dado su bajo consumo nacional y cotización en el mercado peruano. Asi, solo ciertos yacimientos ubicados en el norte de nuestro país producen y generan divisas que no sobrepasan los 6 millones de soles. En el marco de esta situación, el objetivo del siguiente estudio, pretende reactivar el consumo nacional de los yacimientos del Sur del país, -en tanto volumen e importancia comercial por medio del uso de un método de beneficio apropiado. La formación de los yacimientos del Sur, a diferencia de los de Piura y Bayovar, se da por la emanación postvolcánica de gases sulfurosos, generandoimpregnaciones de azufre en las lavas y tufos del Terciario Superior y Cuaternario. Posteriormente se produjeron fracturas en las zonas contíguas de los volcanes, formando depósitos lenticulares de extensión variable. Dichos depósitos son superficiales puesto que solo cerca de este espacio se puede mantener la oxidación del sulfuro de hidrógeno y los gases están a temperatura baja para depositar azufre. En cuanto al costo del azufre tenemos el costo de explotación, beneficio, transporte y embarque. Finalmente, se deduce que la fundición del azufre como la filtración, soliflucción pueden ser favorables en el uso de métodos de explotación menos costosos, asi como el incremento de la explotación depende de un mercado común estable y de un cálculo exacto de los costos de producción.

Jul 20, 1956

By Dwight L. Sawyer, Roy T. Sorensen

The Bureau of Mines has investigated the recovery of alumina by hydrochloric acid leaching of calcined kaolinitic clay . Bench- scale studies indicated that horizontal belt filtration was a pprraaccttiiccaall method for separating the siliceous residue from aluminum chloride liquor generated in the leaching step . Miniplant -scale continuous testing was performed to evaluate the filter circuits and to compare filtration response of different calcined kaolin feed materials and of different agitatorbaffle designs in the leaching reactors . Soluble alumina recovery with a single filter ranged from 94 pct with minus 10 -mesh feed more than 96 pct with minus 35-mesh or misted feed . Process advantages were confirmed for the calcined misted kaolin feed material prepared by a Bureau-developed misting process . With two filters in series , an overall filtration rate of 100 lb solids /hr.ft - 2 of filter area was attained with a soluble alumina recovery of more than 99 pct . More than 99.5 pct alumina recovery was obtained with a thickener and a two - filter circuit for either the minus 35-mesh or the misted feed . Modifications in leaching reactor design made to decrease particle- toparticle attrition were successful and significantly increased filtration rates and decreased flocculant requirements .

Jan 1, 1965

By J. Fellowes, V. Landais, J. Robson, J. Carr

"Aerospace Al-Zn-Mg-Cu (7xxx) alloys are known to be susceptible to environmentally assisted cracking (EAC). This phenomenon has been studied intensively for many decades, leading to empirically adopted methods to mitigate this problem through overaging and composition design. In parallel, many theories have been developed to explain EAC in 7xxx, but none is yet universally accepted. Today, a number of emerging techniques offer potential to shed new light on EAC in 7xxx. The purpose of the present paper is to demonstrate how X-ray tomography (XCT) combined with electron microscopy can be used to identify the true crack path in 3-dimensions, and hence identify material for site specific electron microscopy analysis. Composition mapping over large areas to high accuracy has been performed using a modern electron microprobe analysis system. This has been combined with transmission electron microscopy to investigate local composition in matrix and precipitates at high resolution. This combination of techniques across length scales offers the potential to provide new insights into the links between local composition, microstructure, and EAC resistance.INTRODUCTION Environmentally-assisted cracking (EAC) is a phenomenon which dramatically decreases the performance of metals and can cause premature failure of large structures. Observed in situations where components were not subjected to critical loads and no widespread corrosion was involved, this type of brittle failure is extremely difficult to predict. The EAC designation covers a number of phenomena, e.g. stress corrosion cracking (SCC), hydrogen embrittlement (HE), corrosion fatigue (CF), etc. Initially identified in steels, EAC can also affect other metals such as high-performance aerospace aluminium alloys, and this phenomenon has been a concern for industries for decades. Extensive research has been conducted on the effects of various environments (moist air, saline water, dry hydrogen gas, etc.) on microstructures and crack propagation, however no consensus has been reached and the exact nature of the mechanisms that control EAC is still being debated (Birnbaum & Sofronis, 1994; Gangloff, 2007; Holroyd & Scamans, 2013; Lynch, 2012; Oriani, 1972; Scamans, Alani & Swann, 1976, Young & Scully, 2002)."

Jan 1, 2018

By E. W. GOODWIN, V. F. Parry, J. B. Goodman, L. D. Schmidt, J. D. Davis, A. C. Fieldner, W. S. Landers, J. L. ELDER

The Heliopore process is essentially an arrangement that uses the waste heat in the exhaust gas of an internal - combustion engine to carbonize coal (noncaking ) or lignite . The gases distilled from the coal furnish fuel for the internal - combustion engine , which drives an electric generator . Thus the main products of the plant are electricity and char . A flow diagram illustrating the principles of operation of the Heliopore process is given in figure 1. The primary equipment consists of a carbonizing retort , gas cooling and scrubbing equipment, a gas storage holder, and an engine to burn the gaseous carbonization products . Coal is charged into the top of the retort while the hot gases from the engine travel upward through special ducts in the retort countercurrent to the coal flow . The hot gases never come into direct contact with the coal . Char is discharged at the bottom of the retort and hot gases at the top . The gaseous products resulting from carbonization of the coal are drawn off by an exhauster through the condensing and scrubbing equipment to take out tar and liquor , then to a gas holder , and finally are burned in a gas engine . The gas engine drives an electric generator and the engine exhaust gases are returned to the retort to carbonize coal . The entire process was intended to be continuous and self - sustaining, and to use coal as the only fuel . The plant may be said to be a large - scale pilot plant in that , although it is of full commercial size , its main purpose is to provide data for the design of others of its type . The installation tested had a daily throughput of about 4 tons of coal . Figures 2 , 3 , and 4 picture some details of the plant and equipment used in the experimental testing . Further details of the equipment and engineering drawings of the castings are shown in figures 8 to 22 in the Appendix .

Dec 1, 1943

By J. O. Down

St. Marys Cement Company operates two cement plants in Southern Ontario, Canada. The original plant, located at St. Marys, a town 20 miles north of London, Ontario, began operations in 1912. A second plant, located at Bowmanville, Ontario, 40 miles north east of Toronto, began operations in 1967. In June 1973, St. Marys Cement began feasibility studies of modernizing their wet process plant at St. Marys. Over its 61 year life, this plant had been expanded from 335 m. tons per day (375 s. tons per day) to 2000 tpd (2200 s. tons per day), with all the original equipment retired several years ago. The objectives of the feasibility study were to develop a conceptual plan for a dry process plant and to de-, fine the appropriate process method and equipment. This study proceded along four fundamental fronts: a) How could the clay raw material, a glacial till with up to 20% boulder content, be processed in dry form and beneficiated? b) Were the raw materials suitable for the most efficient form of dry process kiln, the 4-stage preheater? If a 4-stage preheater kiln is selected should it utilize a precalciner? c) What type of clinker cooler should be used? d) What environmental constraints would be imposed on this plant and how can they be reconciled with capital and operating limitations? During the feasibility stage, pilot plant work was done on two possible solutions to the clay problem, operating plants in Europe were visited and discussions held with kiln and mill vendors.

Jan 1, 1977

By K G. Harding, A Osman, A du Toit, F K. Crundwell, C M. Sheridan

"Most mineral processing plants have high water requirements for their operational activities. These plants often function in an environment where water is becoming increasingly scarce. An increase in population will result in an increased demand for water; potentially beyond the limits of supply and hence increased competition for the resource. In South Africa, Gauteng and the North West Province are likely to be first to experience a shortage of potable water.In order to avoid a water crisis, efforts must be made to ensure the effective management of water resources and the minimisation of wastage. Hydrometallurgical plants have a responsibility to society and the environment to operate in a sustainable manner - reducing their water requirements will certainly assist towards developing a sustainable footprint.This project improved site water management by: surveying the potable water and storm water systems with a view to assessing the current water accountability and determining methods to improve accountability determining the monthly and yearly water balance for the site and presenting it in the form of a water balance sheet drawing up an input-output and operational model in accordance with the Minerals Council of AustraliaÆs æWater Accounting Framework for the Minerals IndustryÆ calculating the water footprints of the refinery identifying ways in which water savings could be achieved recommending management systems for water usage monitoring.This work was conducted in South Africa. The value of this work lies in that it established the current baseline and assisted in developing management systems that can reduce water usage sustainably.CITATION:Osman, A, Crundwell, F K, Harding, K G, Sheridan, C M and du Toit, A, 2013. Water accountability and efficiency at a base metals refinery, in Proceedings Water in Mining 2013, pp 277-286 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By K Blay, C McCamley, P Petrucci

The Newmont Boddington Gold (NBG) processing plant was designed for 35Mt/y with ball mills expected to deliver a combined new mill feed rate of 4837 tonnes/hr. Since beginning commercial production in late 2009, the plant has steadily increased throughput to meet design capacity in 2014 and reached 37 Mt/y in 2015. Through improved efficiencies, changes to the milling circuit have taken place since commissioning to take the plant beyond its design to an actual throughput of 39.0 Mt in 2017 and a budgeted throughput of 39.4 Mt/y this year.The NBG milling circuit has four parallel ball mills, each consisting of a 7.9 x 13.4 m ball mill with twin 7.5 MW fixed speed motors in closed circuit with twelve 650 mm cyclones. Each mill is fed by two wet screens with the undersize gravitating to a mill discharge hopper where it is combined with the ball mill discharge and pumped to hydrocyclones for classification. The cyclone underflow is re-ground to a target P80 of 150 µm.This paper will focus on process improvements made to the NBG milling circuit which include cyclone reconfiguration, fine screen panel redesign, implementation of an expert control system, mill power draw increase and grinding media changes to take NBG beyond its design throughput.CITATION:McCamley, C, Petrucci, P and Blay, K, 2018. Going beyond design at Newmont Boddington Gold, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 497–508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Clarence Hall, Spencer P. Howell

Among the more important factors involved in the use of high explosives in blasting operations is the means employed to bring about the detonation of the charge. When flame is applied to high explosives many of them may burn if not confined; but all of them when burning under certain conditions of confinement may detonate. Detonation may also be effected by mechanical means, such as frictional impact caused by a blow or by rubbing between surfaces. By this means, however, the full effect of the explosive charge may not be developed, so that a partial detonation, often accompanied by the burning of the explosive, results. When nitroglycerin was first used it was fired by the application of flame, but considerable difficulty was experienced in exploding it with certainty and in obtaining uniform resl'llts. In 1864 Allred Noble, a Swedish engineer, discovered that nitroglycerin could be surely and completely detonated by exploding in contact with it a small quantity of an initiatory explosive. Mercury fulminate was the substance then found capable of producing the best results There are many other fulminates and other substances that will produce complete detonation of commercial" high" explosives, but detonators or electric detonators containing mercury fulminate as the characteristic ingredient are still almost exclusively used in this country. The term" detonator" is used in the publications of the Bureau of Mines to designate what the miner calls a "blasting cap "-a copper capsule containing a small quantity of some detonating compound that is ignited by a fuse. The term" electric detonator" is applied to a blasting cap that is similar except for being ignited by means of a small wire which is heated to incandescence or fused by the passage of an electric current. One of the conditions prescribed by the Bureau of Mines for a permissible explosive a is that it shall be :fired by a detonator, or preferably an electric detonator, having a charge equivalent to that of the standard detonator used at the Pittsburgh testing station. A further requirement is that this charge shall consist by weight of 90 parts of mercury fulminate and 10 parts of potassium chlorate (or their equivalents). At the request of a manufacturer of permissible explosives, an investigation was undertaken by the bureau to determine the relative strength of detonators and electric detonators having different compositions. The tests of electric detonators herein reported were conducted by H. F. Braddock, junior chemist; J. W. Koster, J. E. Tiffany, junior mining engineers; and A. S. Crossfield, junior explosives chemist, at the Pittsburgh testing station of the bureau. Similar tests of detonators were not conducted because it was believed that the results would not show sufficient variation to warrant such tests. It is hoped that the conclusions drawn from the tests made will be of service to those using explosives by enabling them to select the grade of detonator or electric detonator that will insure the most effective results. The conclusions are given in this bulletin, which is published by the Bureau of Mines as one of a series of publications dealing with the testing of explosives and the precautions that should be taken to increase safety and efficiency in the use of explosives in mining operations. The results of tho experiments described in this bulletin show that the average percentage of failures of explosives to detonate was increased more than 20 per cent when the lower grades of electric detonators were used instead of No. 6 electric detonators, and was increased more than 50 per cent when these lower grades were used instead of No. 8 electric detonators. It is noteworthy, however, that when sensitive explosives, such as 40 per cent strength ammonia dynamite (p. 33), were tested under conditions ideal for detonation, the same energy was developed irrespective of the electric detonator used. When tests were made with a less sensitive explosive, such as a 40 per cent strength ammonia dynamite containing nitrosubstitution compounds (p. 32), the energy developed increased with the grade of the electric detonator used. For example, the average efficiency of four different explosives was increased 10.4 per cent when a No.6 electric detonator was used instead of a No.4 electric detonator, and 14.9 per cent when aN 0.8 electric detonator was used (see tabulation onp.45). The results of the tests emphasize the importance of using explosives in a fresh condition, but as fresh explosives can not always be had in mining work, strong detonators should be used in order to offset any deterioration of explosives from age.

Jan 1, 1913