Search Documents

By G. W. Weems

The specific objective of this investigation was to determine the compressibility factors for helium and carbon dioxide mixtures at -10° and -20° C and pressures to 1,000 psia. A Burnett apparatus was used. Data from the experiments were treated by the method of Barieau and Dalton. Tables of compressibility factors and approximations of the virial coefficients are presented for 10 binary mixtures as well as for helium and carbon dioxide. The results follow the same trend as data previously reported.

Jan 1, 1970

By Larry A. Haas

The U.S. Bureau of Mines, in cooperation with Cleveland-Cliffs, Inc. (Hibbing, MN), investigated ways of enhancing the quality (compressive strength, after-tumble and reducibility) of domestic acid and fluxed magnetite pellets by modifying the oxygen content during the preheat and induration periods of the firing operation . Oxidation of magnetite was best accomplished when sufficient oxygen and time were available before the peak induration temperature was reached. The rate of magnetite oxidation increased directly with the gas oxygen content during the preheat period at 7000 C and above. With 30 pct ( or more) O2 and a preheat rate of 2000 C/min, most of the magnetite was oxidized during the preheat period. With laboratory tube and mini-pot furnace tests, oxygen enrichment during the preheat period improved the pellet properties more in the simulated grate-kiln tests than in the simulated straight-grate tests. The longer induration period with the grate-kiln test resulted in more sintering of the residual magnetite and its reaction with the silicon compounds. When flux was present in the pellets, calcium silicates and calcium and magnesium ferrites were formed. More calcium ferrite was formed when the magnetite was oxidized early and less iron was present in the fayalitic calcium silicate slag.

Jan 1, 1993

By Réal Tanguay, Mathieu Piché, Jacques Carignan, Charles Beaudry, André Bonenfant

"Le gisement Isle-Dieu est situé sur le flanc sud de l'anticlinal de Galinée. La stratigraphie locale comprend, de bas en haut, la rhyolite du Groupe du Lac Watson surmontée par le basalte du Groupe de Wabassee. Un horizon repère, siliceux et sulfure, d'origine sédimentaire, appelé ""Tuffite Clef', est présent au sommet du Groupe du Lac Watson et pend à 45° vers le sud.Le gisement Isle-Dieu est constitué par une lentille qui recoupe, en partie, la ""Tuffite Clef"". Elle est séparée en deux trorçons par un dyke de tonalite. Les données obtenues à partir des forages effectues à travers la rhyolite sous-jacente permettent de définir les zonations chimiques et pétrographiques de la cheminée d’altération.Ces transformation minéralogiques et chimiques sont caractérisées par un enrichissement en MgO, Fe2O3, MnO et un appauvrissement en CaO, SiO2 et Na2O. La zonation spatiale de ces altérations permet de mettre en évidence la géométrie et l'extension des conduits hydrothermaux. L'épaisseur maximale des sulfures massifs au sein de la lentille est en étroite relation avec l’importance des zones d'altération. Les patrons de variations chimiques dénotent une orientation préférentielle WNW des conduits hydrothermaux. Les parties les plus altérées et les plus déformées présentent localement de fortes variations positives en Zr, Nb, et terres-rares; ces concentrations sont vraisemblablement imputables a /' enrichissement résultant de la diminution du volume lors de l'altération.L'étude pétrographique montre que la porosité et la perméabilité du milieu ont joué un rôle important dans la circulation des fluides car les roches de la cheminée présentent des phénomènes de dévitrification, de bréchification et de microfracturation très prononces. La nature magnésienne de certaines chlorites et la perméabilité accrue du milieu semblent en accord avec le modelé propose par Roberts et Reardon, ( 1978 )"

Jan 1, 1990

By Charles T. Ford

In 1971, Bituminous Coal Research, Inc~ established a program to provide the coal industry with the necessary information and technical capability to investigate and evaluate potential problems concerning trace elements in coal and coal-related materials. The initial efforts at BCR in developing or adapting analytical procedures for the precise determination of trace elements in the parts per million to parts per billion range were detailed in a report titled "The Development of Analytical Methods for Determining Trace Elements in Coal and Coal-related Products." A subsequent reports contained descriptions of reliable analytical methods refined by BCR for determining mercury in coal and coal ash and also in coal mine water. his paper reports initial progress in applying recently-acquired trace-element analytical capabilities to solving potential coal industry problems. In this case, the effect of a coal-cleaning process on the distribution and removal of potentially harmful trace elements in coal was evaluated. Coal cleaning offers the possibility of controlling potentially harmful emissions resulting from combustion of large tonnages of coal by removing the pollutants prior to combustion.

Jan 1, 1977

By R. O. Pynnonen

This publication is an analysis of reports to the Bureau of Mines of 44 fatal accidents that occurred during the operation of rubber-tired, front-end loaders in the mineral industry. The causes of the accidents, the nature of the work being performed, and recommendations for preventing similar accidents are included.

Jan 1, 1967

By Ruichen Ren, Xu Han, Caixia Li, Zengchuan Yue

In this paper, the size-density distribution of coarse middling coking coal (CMCC) with different grinding fineness and flotation concentrates was investigated. Then, the flotation behaviors and liberation characteristics of different size-density fractions in ground CMCC were analyzed, and the different size-density fractions were divided into five categories: mostbeneficial, secondary-beneficial, poorly liberated, insignificant-pollution, and serious-pollution. Based on the content of particles with different liberation characteristics, an evaluation index of the liberation characteristic of ground CMCC, namely, the liberation perfection index (LPI), was proposed. The results indicated that grinding changed the size-density composition of CMCC, which affected the flotation performance. Insufficient grinding and overgrinding were not beneficial to flotation. Insufficient grinding caused a higher content of poorly liberated particles and a lower content of most-beneficial particles. Overgrinding increased the content of serious-pollution particles and reduced the content of most-beneficial particles. The size order of the LPI values of different ground CMCC was consistent with the flotation efficiency, and the LPI values of the other two similar samples were overall positively correlated with their flotation performance, suggesting that the method is universal.

Feb 14, 2023

By P. D. Chamberlin

Agglomeration for the heap leaching of gold and silver ores can be defined as the process of attaching fine ore particles (less than 100 mesh) to coarser particles so the fines are immobilized and uniformly distributed throughout the heap, thus making the heap more porous and uniformly permeable to the flow of a leaching solution. Agglomeration techniques and equipment to be described include drum and disc agglomerators, stockpile and belt agglomeration, and the use of vibrating deck and reverse running conveyors.

Jan 1, 1986

By Pedro Forastieri de Almeida Prado

A fim de recuperar-se todos os materiais presentes em painéis fotovoltaicos, o emprego de solventes orgânicos para promover a dissolução da fração polimérica e liberação dos componentes é uma alternativa ao tratamento térmico tradicional. Com o objetivo de verificar-se o impacto dessa etapa na recuperação de prata, o metal de maior valor presente nos painéis de silício cristalino, comparou-se taxas de recuperação de prata para rotas distintas de separação de materiais e cominuição: uma rota por dissolução do encapsulante através de solventes e uma rota por tratamento térmico e destruição do encapsulante. Utilizando-se o isopropanol como solvente, ainda foi analisada a contribuição da cominuição para a liberação da prata. Os ensaios de lixiviação foram realizados com soluções de 5M HNO3, analisando-se as concentrações de prata por ICP-MS. O processo de calcinação foi realizado em forno a 480°C, a dissolução do encapsulante realizada com isopropanol e a cominuição realizada em moinho de facas. Foi concluído que a separação com isopropanol não afetou a quantidade de prata lixiviada na etapa de recuperação de metais. Além disso identificou-se que a cominuição não seria necessária sob as condições de lixiviação utilizadas, já que poderia potencialmente contribuir para perda de prata no processo.

Oct 30, 2017

By James W. Townsend

[The Harrington-Hickory mine in the Star raining district, Beaver County, Utah, has produced approximately 20,000 tons of lead-zinc-silver ores since 1910. Production previous to 1910 is not known. The mine is owned by the New Majestic Mining Co. The property was rehabilitated and operated by James D. Williams under a 10-year lease with option to purchase from April 1943 to May 1949, Loans from the Reconstruction Finance Corporation in the aggregate of $41,000 wore used in construction of an access road, rehabilitation of the mine, and purchase of equipment for full-scale operation. The improved, all-weather access road extends from loading ramps on the Union Pacific Railroad at Milord to the urine storage bins 5 miles west o f town. The mine is serviced electrically by a. 5,000-volt line owned by Telluride Power Co. Mine transformers step the voltage down to 440/220/110 for surface and underground service.]

Jan 1, 1953

By Tina Maniatis

Applied Biosciences has developed a biological technology for removal of arsenic, nitrate, selenium, and other metals from mining and industrial waste waters.The ABMet® technology was implemented at a closed gold mine site in Canada for removing arsenic from tailings pond water. The system included six bioreactors that began treating water in the spring of 2004. Design criteria incorporated a maximum flow of 567 L/min (150 gallons per minute) and water temperatures ranging from 10°C to 15°C. Influent arsenic concentrations range from 0.5 mg/L to 1.5 mg/L. The ABMet® technology consistently removes arsenic to below detection limits (0.02 mg/L). Data from the full scale system will be presented, as well as regulatory requirements and site specific challenges. Keywords: Arsenic, Sulfate Reduction, Metal Sulfide Precipitate, Biological Water Treatment

Jan 1, 2005

By Gus Pantages, Bernard D. Blaustein, Charles Zahn, Irving Wender

Oils from coal hydrogenation have been examined at the Bureau of Mines to learn whether any centers of the optical activity reported in coal would survive catalytic hydrogenation at 450-525 ° C and about 8,000 psig pressure , and , if so , to obtain information about the nature of the active products . Oils from carbonization tars also were examined . Optical activity was found in the majority of the distillate fractions of the hydrogenation oils and in almost all distillates from the carbonization tars . No activity was observed in the tar - acid and tar - base fractions examined . Methods for isolating optically active concentrates included distillation through a packed column , liquid chromatography on silica gel , and adduction with urea . For the materials so processed , the optical activity segregated mainly in the paraffin - naphthenic and the hydroaromatic fractions . Although the specific compounds responsible for the optical activity were not isolated , experimental and spectrometric findings indicate that alkylsubstituted cycloalkane , cycloalkene , and hydroaromatic structures are most likely responsible for the optical activity of the concentrates . The optically active centers probably derived mainly from the steroids and terpenes in the biological materials that participated in the formation of coal .

Jan 1, 1964

By Luttrell. G.

The profitability of coal mining operations is highly dependent on the performance of the coal blending and processing facilities. Many companies have recognized this fact and have instituted optimization programs that require large amounts of coal characterization data, extensive operational information and complex costing models. Unfortunately, this brute force approach to optimization is often overwhelming in terms of time and cost and is generally too inaccurate to be of value in day-to-day field operations. A simpler and more practical approach involves the use of ?micro-price? optimization throughout the coal supply chain. This fundamental concept assigns unit values to each type product (particle or groups of particles) passing through the production units. True optimization occurs whenever all particles with positive worth are recovered and passed to market, while all particles with negative worth are rejected. This paper describes the fundamental workings of the micro-price concept as applied to coal blending and processing operations. Several examples are also included to demonstrate the economic gains that can be realized via the application of this concept.

Feb 23, 2014

By Upfold RW, Velzeboer MD

An underground mine fire will influence the ventilation equilibrium in several ways which results in a redistribution of the ventilating quantities and pressures throughout the whole mine. The ventilation carries the combustion products which constitute the greatest danger of mine fires through the mine and provides the oxygen on which the intensity of the fire depends. However, as a result of the ventilat- ion disturbances created by the fire, changes in airflow patterns can take place which are not always obvious, especially when the mine is being served by several fans. The use of com- puter simulation techniques allow for the likely effects to be tested and the different ventilation options to be evaluated as an integral part of the overall emergency/rescue planning and control procedures.

Jan 1, 1981

By S Grönstrand, C. Perez, A. B. Yañez, F. Coddou, P. Morales, H. Elgueta

"The TankCell® 300 forced air flotation cell designed and built by Outotec, with active volume of over 300 m3, was installed at Codelco’s Chuquicamata concentrator in September 2008. After that, a program was conducted, where the new cell was tested against the plant’s existing flotation cells of type TankCell® 160, with an active volume of over 160 cubic meters.Testing program was exhaustive and detailed. Grade-recovery curves for each setup were reported, along with recoveries by particle size. Secondly, operational characteristics like air feed and froth height setpoints, and power consumption are compared side-by-side. As the third topic, gas dispersion characterization included velocity mapping, holdup, bubble size and bubble surface area flux operating range. The fourth area of interest was the retention time distribution (RTD) of the 300 and 160 m3 cells in comparison. A detailed campaign using radioactive tracer tests was conducted to clarify this.All of the investigations mentioned above are reported in separate papers for more detail. The aim of this paper is to collect the key findings, and present them in real terms, always referring to operability and metallurgy of the cells. It is destined for people designing new plants and to those improving and expanding existing ones. The most frequently heard question is: will the new large cells operate at same efficiency as the smaller ones. In short, the answer is: NO. They operate at improved efficiency!INTRODUCTIONIn the last two decades of minerals processing, there have been three dominant trends of development in the flotation technology: equipment scale-up, cell characterization and circuit modeling. Equipment scale-up has been rapid in the past two decades. In the year 1990, the largest flotation cell in use was 50 cubic meters of size. This year, 300 cubic meters is the largest installed cell. Characterization of flotation equipment and circuits is a very popular subject nowadays and has helped many operations to improve their recoveries through better control strategies, for example by using optimized air feed and level control profiles (Gorain, 2005), (Doucet, Gomez, Finch, 2006), or through better maintenance (Coleman, Urtubia, Alexander, 2006). Characterization work is closely linked to circuit modeling. The aim is to produce sufficient amount of data to allow reliable model building. These models are then used to design new circuits and to improve existing ones. So in summary, these three lines of development have slightly different aims – from capital and operational cost to performance optimization. Ultimately, they converge in the same end result – maximizing the profitability of the operation. Following chapters will summarize the extensive test work and scientific studies at Codelco Chuquicamata. The aim was to compare a TankCell® 300 cell, with nominal volume of 300 m3, against two TankCell® 160 machines, with 160 m3 volume in each. The work should yield answers to questions: does the larger cell produce similar results – is the scale-up successful?"

Jan 1, 2010

By Luiza Cruz Guimarães

Os fabricantes de instrumentos endodônticos de NiTi têm desenvolvido diferentes estratégias para aumentar a resistência à fadiga e à ruptura torcional desses instrumentos. A tecnologia “Controlled Memory (CM)”, que envolve o emprego de tratamentos térmicos em instrumentos já usinados, é uma dessas novas estratégias. Neste trabalho, dois tipos de instrumentos CM foram avaliados em termos de sua capacidade de recuperação de forma e resistência à fadiga após ciclos de flexão até 45 graus e esterilização em autoclave, simulando o uso clínico. Os resultados obtidos em relação às temperaturas de transformação martensítica e reversa, ao momento de dobramento a 45 graus, à recuperação de forma e à resistência à fadiga após ciclos de flexão/esterilização mostraram que os tratamentos aplicados aos dois tipos de instrumentos, embora referenciados como tecnologia CM, produziram resultados diferentes em termos de microestrutura e propriedades.

Aug 17, 2017

By Juan Ayza

Ante el peligro de la concentración y exposición de los polvos de sílices en el personal minero, el presente texto revisa la silicosis -en tanto determina las propiedades de los polvos en reacción y su relación con los medios para detectarlo. Asimismo este estudio constituye en un problema de mecánica de fluidos, donde las operaciones más peligrosas se evidencian en la perforación y explosiones. También se refieren algunos datos sobre los costos de profilaxis de la silicosis y de las indemnizaciones de los enfermos.

Oct 1, 1955

By P Moser, R Ivanova, F Ouchterlony

This paper describes model-scale bench blasts on mortar blocks with distorted drill hole patterns, done in 2013–2014 at the Montanuniversitaet Leoben. The main aim of the project is to see if the fragmentation from and the crack development behind blasts with and without drill hole deviations differ significantly.The dimensions of the test blocks were 660 × 280 × 210 mm (L × W × H). They were mounted inside a yoke that allows the blast waves to escape (see Figure 1). Three rows in each block were shot row by row with a nominal pattern of B × S = 70 × 95 mm. The same nominal delay 73 µs (ie 1 ms per m burden) between holes was used throughout. Blocks with holes of stochastic collar position errors (variations in burden or in burden and spacing but constant row volume) and systematically shifted collar positions (blasts with staggered pattern) were shot. The results were compared to reference blocks without collar deviations.Apart from the sieving analysis, the remaining bench faces were measured with a stereo-photogrammetric method and horizontal roughness profiles for each row were constructed. Sawing slabs from block remains after the third row and use of dye penetrant allowed the study of internal blast damage.The analysis showed that none of the changes in borehole collaring had a significant effect on the sieving curve (median). The sieving results confirm earlier findings though that the fragmentation gets finer with the number of rows shot, implying that blast damage from earlier rows has an influence on the blasting results. The tests demonstrated that the nequiv (equivalent n-value) has increased ten per cent by shooting staggered pattern and decreased by seven per cent by pattern with burden and spacing errors. For the rest of the patterns, the nequiv was roughly the same.The surface roughness investigation showed that a smooth surface was achieved by the staggered pattern. The other deviations patterns did not show a clear trend.The internal blast damage, which was measured in the remaining part of blocks, showed that out of eleven, four crack families seemed to be most affected by blasting. The comparison of the reference and distorted patterns showed that less cracks were apparent for the staggered pattern, ie less damage was introduced.CITATION:Ivanova, R, Ouchterlony, F and Moser, P, 2015. Influence of distorted blasthole patterns on fragmentation as well as roughness of, and blast damage behind, remaining bench face in model-scale blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 693–706 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Many young mining engineers do not consider consulting as a possible job, believing that many years of working on-site is required to achieve practical experience, develop expertise and acquire industry contacts. However, mining consultancies employ engineers with varying levels of experience, including part-time university students, graduates and engineers who are relatively new to the industry. This paper outlines the role of a young engineer in a large mining consultancy and the benefits to both the consultancy and the client of having a mix of consultants with a diverse range of experience. From the authorÆs perspective, the work experience, lifestyle and rewards of mine consulting are compared to site based work, including a discussion on whether consulting is able to offer the professional development that a young engineer needs.

Jan 1, 2009

By Kathleen Lagnese, Srikanth Muddasani, Kashi Banerjee, Carla Robinson

"Mine water generated from underground coal mining operations contains both dissolved and particulate solids. Dissolved solids primarily consist of sodium, calcium, magnesium, potassium, chlorides and sulfates. When discharged to a receiving stream without treatment, these constituents create a potentially toxic environment for aquatic life.A case study is presented to discuss how a centralized treatment plant treats mine water from six locations to meet discharge limitations for chlorides. Located in West Virginia, this facility consistently achieves less than the National Pollutant Discharge Elemenation System (NPDES) permit limitation of 218 mg/L chlorides in the discharge while generating almost zero liquid waste. The dissolved solids concentration in the influent ranges between 5,000 and 10,000 mg/L, with chloride concentrations of 1,000 to 2,000 mg/L and sulfate concentrations of 2,000 to 6,000 mg/L.The mine water is treated using advanced treatment technology to produce clean water for discharge or reuse. The treatment process comprises aeration, softening, filtration, reverse osmosis (RO) reject softening, evaporation, crystallization, final effluent remineralization and sludge dewatering. The solid waste generated in the treatment process is landfilled on site. The leachate is sent back to the facility’s thermal treatment process. Because no liquid waste leaves the property, this plant is termed a zero liquid waste (ZLW) facility.The advanced water treatment system was built to meet a new 218 mg/L regulatory limitation imposed by the West Virginia Department of Environmental Protection for chlorides discharged to surface waters. The system is designed to treat a maximum flow of approximately 795 m3/h (5 million gpd) of mine water. The treatment process utilizes RO membrane treatment to achieve the effluent criteria, and evaporation and crystallization technology to manage the RO concentrate from the water treatment process. As a result, the system produces clean water for discharge while generating zero liquid waste. The effluent water can be used for industrial purposes or discharged to a receiving stream. A water impact index (WIIx) study indicated that discharge of this high-quality water into the Monongahela River watershed may improve the water quality for downstream water users. The waste produced in the treatment process, including softening sludge and salt, is disposed of in an onsite landfill. Currently, the plant is treating at an average flow of 490 m3/h (3.1 million gpd) of mine water with an average influent chloride concentration of 1,530 mg/L and an average effluent chloride concentration of 11 mg/L."

Jan 1, 2014

By Hemant Agrawal, Arvind Kumar Mishra

Rock breakage using blasting is one of the important operations of the mining industry. The delay timing decides the initiation sequence of holes in the blasts and is a crucial factor to improve the overall blast performance. Blast-induced ground vibration is an undesired yet unavoidable outcome of blasting. Peak particle velocity (PPV) is commonly used to measure the magnitude of blast-induced ground vibration. Channelization and better utilization of explosive energy delay are provided between blast holes using initiating systems. The use of different initiation systems even on the same site results in a very significant difference in the values of PPV generated. Due to scattered delay timings of pyrotechnic detonators, the scaled distance predictor equations obtained become unreliable. The error/scatter in delay timing leads to overlapping of holes and hence increases in maximum charge per delay. In this paper, an analytical approach has been discussed to measure the overlapping of holes during blasting with initiation systems having inherent cap scatter. The analytical approach will be calculating the probable overlapping of holes due to scatter in delay timing and will help blasting engineers to understand the variation in maximum charge per delay due to pyrotechnic based initiating systems. In this study, a total number of 102 blasts were conducted using different initiation systems at two different opencast coal mine and 221 corresponding blast vibrations events were recorded.

Nov 10, 2020