Search Documents

By R. A. Price

The base of the biozone of Olenellus is accepted as the most universally applicable criterion for defining the base of the Cambrian System. The use of this definitive criterion is restricted by important practical considerations. In the southeastern Canadian Cordillera this zone appears to truncate the basal ortho-quartzite of a west to east marine -transgression. This transgression began in Interior British Columbia in the Late Proterozoic and terminated in the region of the present Rockies in the Late Waucobian. Most of the material deposited by the transgressing sea originated in the eastern positive element 'Laurentia' and was transported over the intervening low Proterozoic-Windermere erosion surface. The configuration of the advancing shoreline and the distribution of the sediments were controlled by the tectonic activity of positive elements in northwestern Montana (Montania) and in the Fairmont Hot Springs-Radium area of British Columbia.

Jan 1, 1956

By F. Garacia, J. Cervik

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of a discharge pipe. These measurements are erroneous and tend to be high by as much as 30 pct. The Bureau of Mines deter- mined method factors (correction factors) for anemometer measurements taken in this manner. Method factors for 4-, 6-, and 8-in (10.2-, 15.2-, and 20.3-cm) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By Brian Metcalfe, Kord Wissmann, Gianni Martinez

The Middle East consists of vast deserts that reach temperatures up to 50 degrees Celsius, with some areas characterized by endless sand dunes. When the project team selected the location for a large new transportation project, little did they know that the site would be characterized by soft, nearly normally consolidated silt and clay extending below a thin sand crust. Searching for solutions, the design team elected to reinforce the subsurface with Rammed Aggregate Pier® (RAP) ground improvement elements and desired verification that the novel method would stand the test of prolonged static loads. Because the concrete pavements would serve to spread the load, a “zone load test” was performed, consisting of applying a uniform bearing pressure of 150 kPa over a 7.5m square concrete footing. Unlike individual pier load tests, the zone test allowed the project engineers the opportunity to confirm design parameter values under large-loading area conditions, a situation not often available to most designers. This paper presents the results of the zone load test whose results may be interpreted to better understand design parameter values. This paper is of particular significance because it adds a value contribution to the relatively few numbers of “group load tests” available in the literature for ground improvement applications.

May 1, 2022

By Michael J. Marinigh

"Increased safety requirements, higher operational costs, greater environmental restrictions, and new competitive processing techniques are the challenges smelter operators must confront in order to remain economically viable.In converting furnaces which have tuyères such as the Noranda Reactor and the Teniente, Peirce- Smith and Hoboken converters, efficient tuyère line management is critical to optimizing blowing rates, increasing refractory life, and improving safety.This paper will describe recent improvements made to equipment used for tuyère punching, tuyère silencing, tuyère pyrometry and refractory drilling of tuyères and how the proper application of the equipment can lead to operational and safety improvements."

Jan 1, 2009

By V. Rajaram

The oil shales located in the Appalachian Basin cover an eight-state area of the eastern U. S., and are referred to as Devonian (black) shales. These shales have been exploited for their gas potential for several years. The Institute of Gas Technology (IGT) has conducted research since 1972 on the production of shale oil from the Devonian shales, and this resulted in the development of the HYTORT process. This process demonstrated that the yield from the Eastern oil shales can be greater than the value indicated by the Fischer assay method. IGT estimates that 423 billion barrels (67.3 x 109 m3) of oil could be recoverd by HYTORT processing of surface-minable eastern U. S. shales. Recently American Syncrude Corporation and Southern Pacific Petroleum N. L. have proposed oil shale projects in Kentucky. This paper will describe the surface mining and retorting techniques that have been studied for exploitation of the Devonian shales, and enumerate the problems that have to be overcome before commercial production can be realized from these shales.

Jan 1, 1983

By M. J. Marinigh

Increased safety requirements, higher operational costs, greater environmental restrictions, and new competitive processing techniques are the challenges smelter operators must confront in order to remain economically viable. In converting furnaces which have tuyeres such as the Noranda Reactor and the Teniente, Peirce Smith and Hoboken converters, efficient tuyere line management is critical to optimizing blowing rates, increasing refractory life, and improving safety. This paper will describe recent improvements made to equipment used for tuyere punching, tuyere silencing, tuyere pyrometry and refractory drilling of tuyeres and how the proper application of the equipment can lead to operational and safety improvements.

Jan 1, 2007

By C. Díaz

Roast-reduction smelting (RRS) of nickel concentrate, combined with flash smelting of copper concentrate, was one of the process options that Inco considered as a means of meeting its 1994 sulfur dioxide abatement target at its Copper Cliff operations. RRS involves deep roasting the nickel concentrate in fluid bed roasters. The roaster off-gas is heated in a sulfuric acid plant, and the low sulfur calcine is reduction smelted with coke in an electric furnace to yield a sulfur-deficient matte. The latter material is converted to Bessemer matte in Peirce-Smith converters, with minimal evolution of sulfur dioxide, and the converter slag is reverted to the electric furnace. Excellent nickel and cobalt recoveries are obtained. This paper discusses the development of RRS, including extensive commercial scale testing at Inco's Thompson Smelter, and its key operating parameters.

Jan 1, 1993

By N. A. Karl, D. R. Wilburn

"This summary of international mineral exploration activities for the year 2015 draws upon information from industry sources, published literature, SNL Metals & Mining (SNL) (Charlottesville, VA) database and specialists in the U.S. Geological Survey (USGS) National Minerals Information Center. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry, and presents analyses of exploration activities performed by the mineral industry.Three types of information are reported and analyzed in this annual review of international exploration: budgetary statistics expressed in U.S. dollars provided by SNL; regional and site-specific exploration activities that took place in 2015 as compiled by the USGS; and regional events that affected exploration activities including economic, social and political conditions, which were derived from published sources and discussions with USGS and industry specialists. Commodity and regional compilations are presented in this summary. Because multiple sources were used to develop commodity and regional compilations, statistics may vary depending on the source and type of data that are being reported.The SNL data summarize planned company budgets for worldwide exploration activities in 2015 for 24 nonfuel mineral commodities and metal alloys and are based on company surveys. Surveys focused on precious metals (gold, platinum-group metals and silver), base metals, (cobalt, copper, lead, molybdenum, nickel, tin and zinc), bulk commodities (bauxite, chromite, iron ore, manganese, phosphate and potash), and other commodities (diamond, graphite, heavy-mineral sands, lithium, niobium, rareearth elements (REE), tantalum, tungsten and uranium).USGS data compilations and analyses are based on information provided by USGS mineral commodity and country specialists, as well as industry contacts and published trade journals. The USGS data summarize exploration site data collected for more than 80 minerals and materials, with a focus on base metals, diamond and precious metals. The USGS analyzed available information to assess the level of exploration activity in 2015 and to report trends in mineral exploration activity for the period 2005 through 2015. These analyses identify where mineral exploration is occurring by commodity and region and the intensity of activity that is taking place in each region for selected mineral commodities, and determines those factors that most affect changes in exploration activity."

May 1, 2016

By Ludwig Schmidt

The consumption of gasoline in the United States varies materially with the seasons; during some of the summer months it exceeds the rate of production and in the other seasons the production of gasoline exceeds the consumption, The usual practice of the larger refiners is to store surplus stocks during the winter season in order to meet the heavy demands during the summer months. The following table shows the stocks of gasoline at refineries on the last day of April for the past five years: 1919 593,616,170 gallons 1920 643,5526644 " 1921 747,222,900 " 1922 892,567,766 " 1923 1,336,417.871 "

Jan 1, 1923

By P. van der Steen

This paper examines the historical developments in diamond beneficiation technology and the impacts on the industry. The art of diamond beneficiation has given way to the application of scientific process, but at considerable capital expenditure. The shift in beneficiation methodologies has been disruptive to the traditional skills set of the industry, but evolutionary change continues and has been beneficial to the quality of the final product.

Jan 1, 2010

By C Laming, P M. Hetherington, F A. Pym, M P. Murphy, K E. Crook

Reconciliation is a powerful tool used by mining operations to compare the mass and grade of ore produced with what was estimated before mining. The primary objective of reconciliation is to verify that the estimated planned metal production is achieved during processing, allowing issues to be identified for which adjustments can be made throughout the mining value chain to improve recovery and maximise efficiency. Traditionally, the mine plan is based on estimated mine grades using sampled exploration drill hole or blasthole grades. Reconciliation discrepancies between the mine plan and mill are common due to such factors as insufficient or non-representative sampling, poorly conceived models, or unrecognised blast movement. MineSense Technologies Limited® (MTL) has developed an X-ray fluorescence (XRF) sensor-based ore classification system that is installed on mining equipment to provide real-time grade estimates of run-of-mine material at bucket, truck, or belt-scale. Bucket level grade estimates provide insights into grade variations at the mine face that were never before available. This data set eliminates some of the leading causes of reconciliation discrepancies and enables tracking of tonnages and grades from the mine face to the processing plant at bucket resolution with confidence. Bucket-by-bucket grades at the mine face enable dynamic optimisation of the mine plan to stabilise the mill feed grade through blending of mine and stockpile loads. Beyond stabilising feed grade, Mine to Mill reconciliation combined with the full XRF spectrum response can generate proxy relationships to ore characteristics like hardness and recovery. These properties can then be predicted at the mine face, enabling further optimisation of the downstream mill feed, not only for grade, but also for power and water consumption, reagent addition, and recovery. This paper presents the benefits of MTL technology for grade reconciliation and mill performance optimisation at a Cu Mine in BC (Canada).

Mar 22, 2022

By D. R. Derry

This paper up-dates an earlier paper by the author on the rate of new Canadian mineral discoveries and the exploration methods which were principally responsible for these finds. He concludes that the ratio of exploration expenditure to production value must be increased if we are to provide sufficient new reserves for the future.

Jan 1, 1970

By J. C. Edwards

The Bureau of Mines developed a mathematical model for analysis of the impact of scrubber bed length, porosity, and gas flow rate on the absorption of C02 in a breathing apparatus. The model accounts for the decrease in available absorbent through chemical conversion. The pre-dicted efflux of C02 from a canister containing LiOR compared favorably with measured values reported elsewhere. It was determined from a com-putational study that the time for breakthrough of C02 at a prescribed level is nearly directly proportional to bed length and inversely pro-portional to gas flow and porosity.

Jan 1, 1987

By E. P. Pfleider, W. G. Pariseau

This paper reports the theoretical and experimental results of an analysis of ore pass drawdown as a problem in soil plasticity. The method of analysis developed appears to be a promising technique of investigating the mechanics of fragmented materials. A reconstructed plasticity theory brings experiment and theory into reasonable agreement, and hence may provide the foundation needed for rational ore pass design. The gravity-induced movement of broken rock through ore passes is an economical method of transporting fragmented materials through large vertical distances in underground mines, provided the ore pass is well designed. Unfortunately, the design procedures now followed do not very often result in ore passes that function properly. On the one hand, the huge accumulation of empirical data pertaining to the movement of materials in gravel bunkers, storage bins, deep grain silos and other structures that have features in common with ore passes remains uncorrelated. On the other hand, there is a dearth of experimental data substantiating theoretical models of material behavior. Consequently, reliable generalizations encompassing the broad spectrum of problems involved have not been forthcoming. AS an initial step towards improving the situation, a detailed case study of two-dimensional ore pass drawdown was made. The mechanics of the process were analyzed theoretically as a problem in soil plasticity and tested experimentally through observations of a laboratory ore pass model. THEORY Taylor1 defines a soil as a "mass commonly considered to consist of a network or skeleton of solid particles, enclosing voids of varying size." Broken rock in an ore pass is such a material. In plasticity theory this material is replaced by an idealized substance that deforms elastically up to some state of stress at which slip or yield occurs,2 For com-pressive states of stress, the Mohr-Coulomb criterion is a satisfactory yield condition. After the yield point is reached, the ideal soil deforms in accordance with the concept of plastic potential.4 Under plane strain conditions the governing equations separate into a system of stress equations and a system of velocity equations.' Only stress variables appear in the stress system. The velocity system, however, contains a stress variable. The two systems are, therefore, coupled. Both systems are hyperbolic, and each has two real, distinct families of characteristic curves that coincide according to the classical theory of ideal soil plasticity. The

Jan 1, 1969

The Industrial Minerals Div., of the AIME meeting scheduled for Nova Scotia Sept. 8-12, 1953, promises to be one of the outstanding gatherings ever attended by the group. Complementing the educational value of technical sessions will be the superb fishing, boating, golfing, and tennis facilities. [ ] Sponsor of the meeting is the Nova Scotia Mining Society. The Canadian Institute of Mining and Metallurgy and Industrial Minerals Div., AIME have been invited to participate. The land immortalized by Longfellow's poem, Evangeline, still contains much of the forest primeval-enough to make it a wonderful vacation spot for delegates and their families. Its scenic beauty is almost unmatched in the area north of the border. Quoting from the Nova Scotia tour book; "Nova Scotia, once known as Acadia, is 374 miles long, from 600 to 100 miles wide ... Excepting the Isthmus of Chignecto, 17.5 miles wide, the province is entirely surrounded by water, no portion being more than 50 miles from the sea . . . has 4625 miles of coastline, guarded by 356 lighthouses and fog alarms. The province is renowned for its picturesque coastline, its harbors dotted with islands, its deep valleys and multitude of beautiful lakes." A progress report on the plans for the meeting will be made monthly. Thus far, technical sessions will be held at Keltic Lodge, Ingonish, N. S. The lodge will also be the starting point for many of the field trips and social events which are in various stages of planning and development.

Jan 1, 1952

Los Angeles may well be host to one of the most historic gatherings of AIME members Feb. 16 to 19, 1953, when the 175th General Meeting is scheduled to take place. Plans in the formulative stage indicate that the meeting will be one of the largest ever held by AIME. Headquarters will be the Hotel Statler, now nearing completion of construction. The hotel will be one of the most modern hostelries of the century. The first technical session, of which there will be more than 75, will take place Monday, February 16. Mineral Industries Education Div. and the Board of Directors meet Sunday, February 15. Sessions will end with a meeting of the Council of Section Delegates on Thursday. Deadline for papers that may be preprinted for presentation at the meeting is Sept. 15, 1952. However, division program committees may list papers for presentation after that date if they choose. Various committees are engaged in formulating final plans for the meeting. Developments will be announced as progress is made.

Jan 1, 1952

By Staff

In 2012, the estimated value of mineral production increased in the United States for the third consecutive year. Production and prices increased for most industrial mineral commodities mined in the United States. While production for most metals remained relatively unchanged, with the notable exception of gold, the prices for most metals declined. Minerals remained fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels, including mining, processing and manufacturing finished products. Minerals? contribution to the GDP increased for the second consecutive year. Trends in other sectors of the domestic economy were similar to those in mineral production and consumption rates (Table 1). After continued decline following the 2008-2009 recession, the construction industry began to show signs of improvement late in 2011 and throughout 2012, with increased production and consumption of cement, construction sand and gravel, crushed stone and gypsum, mineral commodities that are used almost exclusively in construction.

May 1, 2013

By J. A. Herdlick

The Star mine, near Neihart, Cascade County, Mont., has been in continuous operation since the construction of a 50-ton bulk flotation mill in 1939. The mine was examined by G. N. Bennett, an engineer of the Bureau of Mines, in November 1942. At that time the life of the operation appeared to be limited and a program of crosscutting and core drilling were recommended. The program had as its objective the investigation of a promising undeveloped area lying west of the Star vein and, if possible, the development of enough reserves in this area to insure continuous operation during the war emergency. Development of additional reserves would then justify necessary changes in the mill in order to eliminate the heavy penalties imposed for excess zinc in the bulk concentrates. The Bureau of Mines work began in February 1944 and was completed in September 1944. The project was started by Wilder R. Brinton and continued by Thomas W. Oster, mining engineers in the Bureau's Montana district office. Beneficiation tests on are and concentrates were made after completion of the underground work. This report presents the factual data obtained during all phases of the Bureau's investigation.

Jan 1, 1949

By P. Croney

Environmental monitoring requires major effort and expense but management of data receives less attention. A modem database system can manage hydrochemistry, water levels, meteorology, geology and downhole geophysics data and is flexible to allow the storage of ad hoc data. Reports can be customized by the user and derived data generated from input values. The production of high quality maps with contours and hydrochemical diagrams is an essential part of the reporting process. These maps integrate directly with the current site survey information. These facilities are best provided by storing the data in an industry standard database such as Oracle or Access to which customized AutoCAD and Microsoft Office routines make direct SQL calls.

Jan 1, 1997

By H. C. Fuller, E. L. Anderson, F. S. Wartman, M. A. Cook

"This paper gives an account of the production of ductile-grade titanium powder in 100-pound batches by reduction of purified titanic chloride with magnesium, followed by grinding, leaching, and magnetic separation of the reaction product. Apparatus, technique, and methods of controlling product quality are described, and some data on operating costs are given.Although man has been aware of the existence of the element titanium for over 150 years, only recently has the metal itself been available in a form pure enough, particularly with reference to absorbed gases, to allow an estimate of its physical properties. In comparison with mild steel, the tensile strength of titanium is about the same, the resistance to atmospheric corrosion greater, and the specific gravity much less.These properties suggest the usefulness of titanium as a structural material for applications requiring resistance to atmospheric attack and a good strength-weight ratio. Although known reserves of titanium, high-grade enough to be useful at present are not sufficiently extensive to predicate that titanium might supplant iron, aluminum, and magnesium for structural purposes, the reserves are large enough to make its use as a structural material quite feasible in certain fields in which its unique properties are required.As a result of these considerations, the Bureau of Mines station at Tucson initiated an, investigation into the technology of titanium in 1938. First, a critical survey and small-scale trial of virtually all suggested methods7/ for producing the metal was made. The method devised by Kroll8/ seemed best adapted as a source of metallic titanium for, although the purity of the product was not as high as that of products from some other processes, it seemed that modifications in technique necessary for larger-scale production could be made more easily.Essentially, in applying the Kroll process, titanium tetrachloride was reduced to metallic titanium by adding the chloride slowly to molten magnesium contained in a molybdenum-lined iron reaction chamber filled with a protective atmosphere of argon. After reduction to the state of completion desired, the reduction mass and chamber were allowed to cool. Then the chamber was opened, and the reaction mass, consisting of titanium, magnesium chloride, and some unused magnesium, was removed by suitable means. Most of the magnesium chloride and metallic magnesium were removed by leaching in dilute hydrochloric acid. The leached sponge was then ground wet in a ball mill, releached in strong acid, and dried Removal of free iron by magnetic separation completed the production process.Development of the Kroll process by the Bureau was undertaken first at the station at Salt Lake City, in 1942 and the amount formed per run was increased in several steps from a few grams to pounds.9/ In addition to increasing the size of batch over that used by Kroll, the technique was simplified somewhat by the use of unlined reaction vessels."

Aug 1, 1949