Search Documents

By Augustus Locke

Jan 1, 1923

By Augustus Locke

Jan 1, 1923

By Fabrício Silveira Garajau

O sopro de oxigênio é a principal operação durante o processo de refino de aço em aciarias BOF (Basic Oxygen Furnace). Este sopro é feito por uma lança de injeção de oxigênio através de bocais supersônicos, que devem ser dimensionados para as condições específicas de operação, como por exemplo, vazões e pressões de oxigênio, altura de banho, altura da lança em relação ao banho, etc. O mau dimensionamento destes bocais tem influência direta no tempo e eficiência de processo, além de comumente resultar em desgaste prematuro dos bocais e na retirada do bico de operação. Este tipo de falha tem sido observado em bicos da Vallourec Brasil. No presente trabalho será apresentada a metodologia de estudos e resultados de análise metalográfica em amostras de um bico de lança usado pela da empresa, além de simulações CFD (Computational Fluid Dynamics) realizadas para se caracterizar o mecanismo de desgaste dos bocais. Estas informações foram utilizadas como base para o redimensionamento dos bocais, objetivando conter os impactos causados pelo desgaste.

Aug 17, 2017

By H. B. Jensen

STUDY of the thermal-solution process was begun by treating crushed oil shale in a small autoclave at temperatures of 700° to 950° F. The effect of temperature, reaction time, type of solvent, and richness of shale upon the amount of organic matter that was removed from the oil shale was thus determined. Following this orientation work a semicontinuous, bench-scale apparatus was built so that heated solvent could be pumped through a bed of shale under elevated pressure, thus removing the converted organic matter from the spent shale. After some operating experience had been gained, a continuous unit was constructed. This permitted treating a slurry of shale oil and pulverized oil shale at about 300 p. s. i. and temperatures of 750° to 850° F. for various retention times. Considerable cracking and polymerization of the shale oil were found to take place during the process. In an attempt to prevent this, a study was made of extraction of the shale in batch-type autoclaves under high partial pressures of hydrogen at total gas pressures of as much as 4,300 p. s. i. at 850° F. The thermal-solution process was found to convert over 90 percent of the organic matter in oil shale to oil and gas. The highest yields of gas and oil obtained without hydrogen pressure were equivalent to 119 weight-percent of those obtained from the same shale by Fischer assay. With a high partial pressure of hydrogen, yields equivalent to 126 weight-percent of Fischer assay were obtained. However, the oil produced by thermal solution has a higher boiling range than that obtained by other retorting methods, particularly so if the thermal-solution process is used without a high partial pressure of hydrogen. Nondistillable oil (all benzene-soluble material that would not distill under 2 mm. Hg absolute pressure without cracking) equivalent to over 100 percent of the organic matter in the shale was obtained without hydrogen pressure in the system. When the process was carried out under hydrogen pressure, the yield of nondistillable oil amounted to 60 to 70 weight-percent of the organic matter. Part of this heavy material is formed partly by polymerization and condensation of the shale-oil solvent used. These reactions, as well as cracking of the solvent to form gas and a carbonaceous deposit on the shale, are unfavorable features of the process.

Jan 1, 1953

By F. S. LOTT, I. S. CULVER

The number of petroleum refineries in the United States decreased during 1948 from 390 to 375, continuing the trend to fewer units of larger individual capacity that has persisted since the peak in number of plants was recorded on January 1 , 1936. Large - scale construction of new processing facilities continued through 1948 with a resultant gain in daily crude-oil throughput capacity of installed equipment from 6,034,252 barrels on January 1 , 1948 to 6,438,995 barrels on January 1 , 1949. The capacity of the average refinery to process crude oil therefore increased during 1948 from 15,472 barrels daily to 17,171 . The principal areas of expansion of facilities were the strategic seaboard districts of the Texas and Louisiana Gulf Coast and the East Coast , and the important Indiana , Illinois , Kentucky, etc. , district that supplies markets in the upper Middle West region . These four districts accounted for 79 percent of the total new capacity added in the United States in 1948. The relatively small petroleum- refining industry of the Other Rocky Mountain district experienced a vigorous expansion in 1948 that will continue during 1949 . Capacity building on January 1, 1949 , amounting to 341,500 barrels daily, was 25,750 barrels lower than the comparable total on January 1 , 1948, but was the second highest on record . New construction was heavily concentrated in the Texas Gulf, East Coast , and Indiana -Illinois

Sep 1, 1949

By Yuzhe Zhang, Matthew Andriese, Jiann-Yang Hwang, Guanghui Li, Zhiwei Peng, Tao Jiang

The microwave power absorption characteristics of iron oxides, including Fe2O3, Fe3O4 and Fe0.925O, have been studied by determining dielectric loss and magnetic loss distributions in 0.05-m-thick oxide slabs irradiated with 1.2-kW, 2.45-GHz microwaves. The results reveal that the dielectric loss is the main factor contributing to microwave absorption in Fe2O3 and Fe0.925O, while the magnetic loss dominates the power absorption in Fe3O4 below its Curie point. Uneven power distributions are observed in the slabs and this phenomenon becomes even worse at high temperatures at which the permittivity increases significantly. Quantification of power absorption in the oxides is of great importance for efficient and uniform microwave heating

Jan 1, 2015

By Gustavo De la Torre

Más allá de contar con las certificaciones ISO 9001, ISO 14001, Y OHSAS 18001, la planta concentradora de Cerro Lindo busca ser catalogada como un desempeño de categoría mundial, lo que implica usar la capacidad total del área (procesos, tecnología y talento humano) basado en un equipo de alta performance-EAR, y gestionar de forma sistemática seguridad, salud ocupacional, medio ambiente, costos, productividad, calidad y confiabilidad, además del proceso productivo. En el presente artículo se analiza información recopilada durante la fase de crecimiento, se presentan diferentes etapas en desarrollo y se describen los estudios realizados en la planta de beneficio, a nivel técnico y de gestión, con óptimos resultados de producción, eficiencia e indicadores metalúrgicos.

Apr 30, 2018

By J. Boldy

This paper is an attempt to place Canadian Precambrian volcanogenic deposits in perspective, by examining and compiling data regarding certain neglected fundamentals of size, grade, value, frequency distribution and spatial density. The discovery roles played by various exploration methods are compared and contrasted, and. using empirical methods, the probabilities of discovery are discussed, combined with the use of an effective 'cost-per-target' program. From these basic observations, realistic exploration judgments may be made. Using similar methodology, this format may be applied to other types of deposits. Precambrian volcanogenic deposits occur in a natural geometric progression in size. They number 110, of which 70% are pre-producers, producers or past-producers. These deposits are bonanzas and generally have a 'net pre-smelter' value of between $43 and $62 per ton. The statistically typical deposit is that which occupies the modal position, has 400,000 tons of ore, a value of $20 million and occurs with a frequency of 40%. A median deposit has 1.4 million tons of ore, a value of $70 million and occurs with a frequency of 15%. An upper-decile deposit ha s 13.3 million tons of ore. a value of $750 million and occurs with a frequency of 6.5%. The major, mid-upper-decile deposits have a minimum of 50 million tons of ore, a value of $3 billion and occur with a frequency of 4%. Five major volcanogenic deposits occur in the Precambrian and account for 54% of production. This contrasts with 55 deposits (all below the median) which account for 3.9% of production.

Jan 1, 1977

By P J. Cullen, B P. Banerjee, S Raval

Continuous monitoring of mining impacts on the surrounding environment is a necessary sustainability criterion. Traditional monitoring approaches such as in situ sampling and airborne and satellite-based remote sensing have several limitations. Over the past few decades, unmanned aerial vehicles (UAVs) have evolved into popular platforms for remote sensing. UAV-based remote sensing has been successfully applied in different sectors, including agriculture, forestry, urban environments and disaster management. However, the potential of UAVs for mine environmental monitoring has not yet been fully established. This paper envisages the use of UAVs and sensor systems to monitor the environment of future mines.CITATION:Banerjee, B P, Raval, S and Cullen, P J, 2015. Unmanned aerial vehicles for mine environment monitoring, in Proceedings Third International Future Mining Conference, pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By M. E. Tyrrell

The Bureau of Mines produced building brick of good quality in an investigation designed to explore the possible utilization of high-glass fractions of municipal incinerator residues in the manufacture of building products. Common clays, lime, and sodium silicate were used as binders for the nonplastic residues Test bricks were formed by dry-pressing, soft-mud molding, and stiff-mud extrusion. A run of standard-size face brick dry-pressed and fired in the West Virginia University Coal Research Bureau pilot plant demonstrated that SW-grade glass-clay face brick can be produced on a commercial scale without difficulty. A cost evaluation made for production of the brick showed an estimated cost of $42.13 per thousand bricks for a shuttle kiln plant and $28.70 per thousand for a tunnel kiln plant.

Jan 1, 1972

By Robert H. Bedford

The New Almaden mine was discovered in 1824, and since that date production of quicksilver has exceeded 1,000,000 flasks. Because of this high production record, the New Almaden area was, upon passage. by Congress of the Strategic Minerals Act of 1939, immediately considered by the Bureau of Mines as a promising location for exploration. In 1941, the Federal Geological Survey undertook a survey of the entire district. R. R. Trengove, an engineer of the Bureau of Mines, made a preliminary study for a project in 1942, and in August 1943 the Bureau, in close cooperation with the U. S. Geological Survey, began the development project described herein. The Bureau of Mines drilled 36 holes, totaling 6,807 feet of diamond drilling, along the contact between the serpentine and Franciscan, sandstones and other sedimentary formations. The ore bodies are found along this contact and occur in the carbonate-silica rock. This report briefly describes the location, history, and ore deposits of the property. The recent operations are outlined, and the work performed by the Bureau is explained in detail.

Jan 1, 1950

By Derek Perkins

"Brenda Mines Ltd. operates an open pit copper and molybdenum mine located in south central British Columbia. The main economic mineralization is chalcopyrite and molybdenite. Pyrite, galena and sphalerite are also present in varying quantities. The mineralization is present in small veins and fractures in a porphyritic quartz diorite host rock.The mill processes approximately 30,000 tonnes of ore daily. The ore is crushed in three stages and then ground in conventional rod mill - ball mill circuits with cyclone classification. The cyclone overflow is fed to the bulk flotation circuit as a pulp with a density of 50% solids. The particle size distribution is approximately 35% plus 65 mesh. Bulk rougher and cleaning flotation produce a concentrate grading approximately 20% copper and 4% molybdenum. This concentrate is fed to the separation circuit, where the copper is depressed with sodium hydrosulphide and the molybdenum is floated. These products are further ground and then upgraded by column flotation. The molybdenum concentrate is pumped to the leach plant to reduce concentration of lead and copper. It is then washed, filtered, dried and packed for shipment to Europe. The copper concentrate is filtered, dried and subsequently shipped to Japan.Prior to November 1977, the mill flotation control was carried out by the assay laboratory using a Philips PW 1540 sequential x-ray spectrograph. The assay set consisted of twelve samples, analysed on a two hourly basis for copper, molybdenum, lead, iron and silica.In order to provide elemental composition information on a much shorter sampling interval and to produce speedier control analysis for automating process control, an Applied Research Laboratories PCXQ on stream analyser was purchased. The installation of this analyser, reduced the turnaround time of the control analyses from (2) hours to (20) minutes. At Brenda, the following assays are used in the mill control strategies."

Jan 1, 1989

By W. E. Robinson

Oil-shale kerogen was processed into oil and oil products before the first oil well was completed by Drake in 1859. However, because of economic and other advantages, natural petroleum has been the principal source of liquid fuels and lubricants since 1859 and is a convenient root of many [organic] chemicals in common use today. In recent years the difference has narrowed between the cost of producing liquid fuels from well petroleum and other sources. This narrowing of cost difference has resulted both from the increased cost of finding new sources of petroleum in the United States and the experimental demonstration of lowered costs for synthetic liquid fuels by the Federal Bureau of Mines and by industry. Available petroleum resources of this country are being reduced and eventually may be inadequate to meet the demand. Alternate means of assuring an adequate supply of liquid fuels for this country include the development of processes for utilizing other carbonaceous materials such as oil shale and coal.

Jan 1, 1960

By Clarence Karr

RESINS from a bituminous pitch, a bituminous coal, a lignite tar, a subbituminous pitch, and an electrode binder pitch wore investigated by the Bureau of Mines. The compositions of these resins were determined by four independent methods of structural detemination: (1) Molecular formula and ring analysis, including ring (2) infrared and ultraviolet spectra; (3) combined pyrolysis/gas chromatography, and (4) catalytic dehyrogenation followed by spectra and pyrolysis. The resin structure was correlated with coal structure, and it was concluded that pitch resins probably consist of essentially unaltered coal molecules carried over with the tar vapors in low-temperature carbonization.

Jan 1, 1966

By K. Bullock, M. Levesque, G. Lyle, D. L. Millar

ABSTRACT The options for reducing the carbon footprint of energy use in mining fall into three categories of activity: i) reducing demand, ii) improving energy utilization, and iii) adopting low carbon energy technologies. In addition to the environmental imperative, the economic case for these activities gains higher priority as the prices of electricity, gas, and liquid fuels increase. Low-carbon, energy-saving technology options that are available to mining industry companies lead to projects with return rates that must compete alongside other capital-intensive projects considered by mining company boards. Energy projects frequently involve longer payback periods and lower rates of return than those of competing bids for capital, such as new mineral property developments. For energy services companies that specialize in the financing, construction, efficient operation, and maintenance of energy projects, the same returns and payback periods can be considered acceptable or even attractive.

Jan 1, 2012

By Lance McAnnuff

Whatever system is devised to control noise and ground vibration from blasting operations must present an effective compromise between the rights of the individual to be undisturbed by the actions of others, and the necessity for society, the whole of the population individually and collectively, to have the services and the products of commerce, industry and transportation along with the relaxation of recreational and cultural pursuits, all at a price within the means of the same society. One of the first jurisdictions in North America to attempt to quantify acceptable environmental limits for specific blasting operations was Ontario, Canada’s largest and most populous province. A process for development of guidelines applicable only to quarries and strip-mining operations was begun in 1974 and culminated with their inclusion in a “Model By-Law” published by the Ontario Ministry of the Environment in August 1978. This paper examines the process of development of the final guideline document and its application over the last 25 years. While acknowledging that the published guidelines for air blast and ground vibration control have provided a useful and generally workable framework for the purposes of land use planning and complaint or damage claim reduction, a number of flaws, weaknesses and misinterpretations connected with their application are identified. Recommendations for amendment of the controversial items are submitted with a view to making these and potentially similar guidelines in other jurisdictions, more acceptable to both government and industry.

Jan 1, 2004

By D. Harrington

Fire is always a serious-menace, whether in a residential or in an industrial region; in wartime it is particularly damaging in an industrial plant. The mining industry is especially vulnerable, as its plants are generally more or less isolated front centers of population and do not have access to modern fire-fighting equipment; moreover, owing to the transitory rapture of most mines, their surface structures; are often relatively flimsy and flammable.. Trained firemen seldom are available at or near mining plants to teach the fundamentals of fire-fighting to local fire brigades, with the result that efficiency in combating actual fires is lacking. Often the attitude "it can't happen here" is held by the management of a mining property, unless the plant has suffered a serious fire; even then lapse of time is very likely to induce forgetfulness as to the possible hazards. The necessity for producing metals for the prosecution of this war has increased management's responsibility. Whereas heretofore the loss of a plant or mill by fire meant merely monetary less to the stockholder of the company, now the national interest is affected, in that the nation suffers from loss of production of minerals indispensable for war purposes.

Jan 1, 1943

By William W. Adams

A larger measure of safety attended the operation of the stone quarries and related plants in the United States during the calendar year 1935 than in any other year for which annual records are available for the industry. The accident rate, covering fatalities and nonfatal injuries that disabled an employee beyond the remainder of the day on which the accident occurred, was 38.19 per million man-hours of work performed. The nearest approach to this favorable record was in 1932 when the rate was 38.48. The rate for 1934 was 41.82; hence the record for 1935 was 9 percent better than that for 1934. Reports from operating companies showed that 51 men were killed by accidents in 1935 and 4,152 men were injured. (See table 37.) The industry employed 73,005 men and performed 110,033,341 man-hours of labor, an average of 1,507 hours of work per man. Measured in man-days, the total volume of labor was 14,623,303, or an average of 200 days of 7.52 hours per day for each man employed. These figures are not strictly comparable with similar figures for the preceding year, as the, coverage of the industry was more complete for 1935 than for 1934 because special facilities were available to the Bureau of Mines for conducting the 1935 canvass that were not available for the 1934 canvass. Reports covering identical plants that were active both in 1934 and 1935 indicate a reduction of about 7 percent in the number of men employed in 1935. This fact suggests that the apparent increase in the number of workers in 1935 is attributable chiefly, if not entirely, to the more complete coverage of operating plants in 1935. The plants from which this inference is drawn employed 21,799 men in 1934 compared with 20,248 in 1935.

Jan 1, 1937

By George J. Tamaro

The design and construction of foundations in the New York City area are usually dictated by the widely varying geologic conditions encountered in the five boroughs, particularly along the spine of Manhattan Island. Rock extends well above sea level at the northern reaches and falls to depths in excess of 250 m at the barrier islands at the southern extremities. These highly variable geologic conditions, significantly affected by glacial activity, dictate different design and construction approaches throughout the five boroughs of New York City. Extensive rock removal is required at the north while long piling is dictated in the south. Similar changes can occur within a project site on Manhattan Island. This paper will describe these conditions in general, will identify the various solutions used to solve these problems and will summarize various foundation types used in the New York City area.

Jan 1, 2000

By B. J. CROSS., Henry Kreisinger, John Blizard, C. E. Augustine

This bulletin presents the results of 36 tests made on a 468-horsepower Edge Moor boiler fired with pulverized coal at the Oneida Street Station of the Milwaukee Electric Railway & Light Co., Milwaukee, Wis. The tests were made by the fuel section of the United States Bureau of Mines in cooperation with the research department of the Combustion Engineering Corporation. Illinois coal was used as fuel; the furnace, burners, and feeders were designed by the Locomotive Pulverized Fuel Co. The object of the tests was to determine what over-all boiler efficiency could he obtained with pulverized coal under various conditions of furnace operation and with coal of different fineness and moisture content. The investigation was thorough. The pulverized coal, as it was supplied to the furnace, was weighed in specially designed tanks placed on platform scales. Twenty-nine of the tests were of 24 hours duration, three of 16 to 18 hours, and four of 12 hours. All tests are reported excepting two-8 and 20-which had to be stopped abruptly, No.8 because a motor actuating the coal-feed screw burned out and No. 20 because of trouble with the feed pump. Tests 1 to 27, inclusive, were made with round burners and tests 28 to 3Rwith spreading burners. In the first nine tests a large excess of air was supplied in an effort to prevent the ash fusing at the bottom of the furnace. In tests 10 to 16 the supply of excess air was reduced in order to get a high efficiency, regardless of the slagging of ash at the furnace bottom. Tests 17 to 27 were made with a water screen about 10 inches above the bottom of the furnace, to make possible the burning of coal with a small supply of excess air without the ash fusing at the bottom of the furnace. Tests 28,29, and 30 were made without the water screen and with a small supply of excess air, and tests 31 to 38 with a water screen around the walls near the bottom of the furnace. Tests 32, 33, 34, and 35 were run with coarser coal than that used ordinarily at the plant. Tests 36,37, and 38 were made with undried coal.

Jan 1, 1923