Search Documents

By J. William Ganser

This paper is one of a series being prepared by the U. S. Bureau of Mines describing mining and milling methods and costs at cement-plant quarries throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically palled to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of Fred Burkett, civil engineer, and F. O. Londrey, chief clerk, of the Trinity Portland Cement Co., for assistance in preparation of this paper, "The Geology of Dallas County. 1918," Bulletin 1818, Texas Geological Survey, Austin, Tex., by E. W. Shuler, was also freely consulted.

Jan 1, 1931

By Leonard P. Vitt

This report details the work done to provide the U.S. Bureau of Mines with a customized Wireless Ground Monitor Wireless Ground Monitor was modified as follows: 1. A voltage regulator was added to prevent false trips with line voltage variations. 2. A Ground Wire Trap was designed to eliminate problems with parallel paths and provide spark suppression. 3. A three phase filter was designed to reduce 60 Hz leakage current. 4. A portable tester was designed to permit complete test of installed systems. 5. The design was modified to insure trip with an open ground wire in the event of a failure of any one semi-conductor component.

Jan 1, 1976

By S Gossmann, J Barlow, S Denner

"Unconventional gas resources, including coal seam gas (CSG) reservoirs, can be located above and below aquifers that provide groundwater for agricultural, industrial, urban and other uses. Development of these resources may, therefore, lead to potential impacts on groundwater supply.Management of reservoir/aquifer interconnections necessitates a program of focused data acquisition. For example, groundwater transfer from shallow aquifers to underlying CSG reservoirs may occur where CSG-containing units subcrop beneath shallow aquifers, possibly at significant distances from operating wells.Arrow Energy is undertaking studies of connectivity between aquifers including an investigation in collaboration with the Queensland Office of Groundwater Impact Assessment to evaluate connectivity between the Condamine Alluvium (CA) and CSG-containing Walloon Coal Measures (WCM).The Condamine Valley hosts highly productive agricultural land with groundwater resources heavily utilised for irrigation. Water demand outstrips available supply and groundwater has been subject to restrictions on further development since the early 1970s. Developments that could have an additional impact on groundwater resources in the CA are of major concern to local landholders. This paper describes: planned field investigations at two sites: 1. Stratheden, where pumping from the WCM will be undertaken 2. Daleglade, where pumping from the CA will occur how the data to be collected from field investigations will be used to refine predictions of flux between the CA and the WCM.CITATION:Denner, S, Gossmann, S and Barlow, J, 2013. Planned field investigation of connectivity between the Condamine Alluvium and Walloon Coal Measures, in Proceedings Water in Mining 2013, pp 91-98 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By Lung Cheng

The Bureau of Mines conducted laboratory tests to investigate the ease of frictional ingition with frozen (nonrotating) conical bits cutting into sandstone. The number of strikes with a new bit to obtain ignition of a combustible methane-air environment was measured. Tests were made with bits tipped with both tungsten carbide and steel at several bit attack angles (angle between bit axis and sandstone surface) and initial tip angles (included angle at the tip of the new bit). Carbide-tipped bits required more strikes for ingition than steel-tipped bits, by a factor of 7 to 10. With a carbide-tipped bit, the number of strikes for ingition increased by a factor of about 3 if the bit attack angle increased by 10° or if the initial tip angle decreased by 10°. During use, abrasive wear of the frozen bit caused a flat surface to form at the tip of the bit, thereby decreasing the tip angle. As the attack angle increased, however, the new bit involved a smaller wear-flat area whereby, abrasive wear was decreased.

Jan 1, 1987

By Carle R. Hayward

WHEN lead production began to recede from the peak productions of 1929 many plants took advantage of the curtailed operations to make necessary improvements and repairs about the plant. There followed a period of adjustment to synchronize production and demand, which merged in the present period of marking time. The lead smelting and refining industry has produced little that is new during the past year except in what might be called makeshifts, which have been introduced to make operation at fractional capacity profitable. This is more particularly true in refineries than in smelters. The Parkes process had become standardized during the period of normal production, with softening, desilverizing, and dezink-

Jan 1, 1935

By Robert Roby

The Mouat copper-nickel deposit in Stillwater County, south-central Montana, was examined by Paul T. Allsman, an engineer of the Bureau of Mines, in 1939. Because of the strategic importance of nickel, a project was executed by John East, Jr., J. J. Naughton, and E. W. Newman, engineers of the Bureau, to further delimit some of the copper-nickel sulfide-bearing bodies that had been discovered by the Anaconda Copper Mining. Co. in 1937 and to investigate the central part of the deposit, which had not been drilled previously. This report is based largely upon the results of the. Bureau of Mines investigation and the results of exploration by the Anaconda Copper Mining Co. In addition, a brief description is given of some other copper-nickel sulfide-bearing deposits along tho Stillwater Complex.

Jan 1, 1949

By G. R. Guillet

THE LATE Dr. D. F. Hewitt, Ontario's foremost authority on industrial minerals, was the first to point out the importance of urban minerals when he produced figures (Hewitt 1968) to prove that the Toronto-Hamilton area was Ontario's second largest mining camp in 1966 (Fig . 1). In that year, the value of mineral production within a 60-mile radius of downtown Toronto exceeded individually that of Steep Rock, Kirkland Lake, Timmins, Manitouwadge and Elliott Lake. Only the nickel and precious-metal production of Sudbury .surpassed in value that of Toronto's pits and quarries. Although that position was unchanged for some years during the early sixties, it was admittedly an unusual situation: gold was still pegged at an artificially low value; uranium was stagnant; and Texasgulf had not entered the scene. However, the point had dramatically been made. The combined value of production from hundreds of sand and gravel pits and dozens of limestone and shale quarries was of formidable proportions. The mining industry of the urban fringe could not be denied. Construction aggregates, cement, building stone and bricks were fueling an apparently insatiable appetite for urban expansion and redevelopment.

Jan 1, 1978

By T. W. Martin

The use of conveyors in large, open pit mines and their drawbacks are discussed. Technological developments such as long distance conveyors capable of handling large rocks are explored. The development and testing by the Bureau of Mines of a prototype crib and cable conveyor for handling large rocks are discussed, and possible modifications of the concept for a production model are examined.

Jan 1, 1984

Halide media are considered as suitable alternatives to cyanide for extracting gold and have received much attention lately. The extraction of gold by iodide-iodine mixture has been patented and briefly studied without much attention given to the fundamental aspects of this process. This paper reports recent studies on the kinetics of gold extraction in iodide media, using hypochlorite, iodine and hydrogen peroxide oxidants. The kinetics of dissolution was found to be dependent on the solution pH, reagent concentration and most importantly the iodide- oxidant molar ratio. Without proper control, the gold surface can be passivated due to the formation of solid products. Thermodynamic modelling was carried out to determine the equilibria governing the dissolution process. The formation of AuI solid was also identified as a possible product during the dissolution.

Jan 1, 1992

By L. B. Phelps

This paper focuses on the use of an integrated mine planing software package entitled "REMINE" which was constructed to provide a project evaluation tool for analysis of remining projects. Coal remining constitutes the affecting of sites which have had a past history of mining and have a pre-existing pollutional discharge. Such sites require a Best Professional Judgement (BPJ) analysis. The program was written to provide such an analysis with flexibility in the mine plans which can be analyzed. The process required for a BPJ analysis will be detailed and mine plan simulation performed to demonstrate the analysis.

Jan 1, 1990

By Hugh M. Roberts

DEVELOPMENT at Steep Rock lake has given rise to renewed interest in the geology of the iron ore deposits in the Lake Superior Region and has implications of no small moment bearing upon methods of exploration in the Precambrian Shield generally. Following upon the Regional Lake Superior meeting of the American Institute of Mining and Metallurgical Engineers in August, 1941, the authors prepared a paper on the Steep Rock deposits, which appeared in the A.I.M.E. publication, Mining Technology, for January, 1943. Between Januar7 and April, 1943, exploration at Steep Rock was continued by means o vertical, Mesabi-type churn-drill holes put down from the ice. This drilling has enlarged the tonnage of ore previously known and has disclosed further facts relating to the origin of the ore. The added evidence, we believe, goes to support the hypothesis that the deposits were formed by a process of replacement due to upward-moving, iron-bearing solutions which came in as igneous after-effects. Accordingly, in presenting the subject to the Canadian Institute of Mining and Metallurgy, it seems best not to change our first explanation, but to prefix the original paper with an interpretation of the results of the more recent explorations completed after its publication.

Jan 1, 1943

By L. Ferland, D. LaRonde, J. C. Caron

"The free-world production of columbium ore concentrates has doubled in the last five years. St. Lawrence Columbium and Metals. Corporation has contributed largely to this expansion, its production rate increasing from 720 tons of concentrates per year in 1961 to 2 200 tons in 1965.To follow the normal market development, the Company initiated an engineering study aimed at establishing the most economical mining methods, thus permitting it to increase its milling rate from 1,000 tpd in 1964 to 2,000 tpd in 1967 and possibly to 3,000 tpd in 1968. The results of this study pointed out the advantages to be gained in converting from an open pit to an under-ground operation. This paper describes how the mining engineering department has successfully developed ""stopes"" from the walls of its No. 2 open pit, in order to assure continuity of its operation during the interval required to develop its underground mine."

Jan 1, 1967

By Shadia Ikhmayies

In this work Thermo-Calc software was used to calculate the phase diagram of the Fe–Si system. The deduced phase diagram includes twenty fields, where three fields represent pure phases; two solid solutions and a liquid phase. There are several fields of two co-existing phases; mixed solid phases, and mixed solid with liquid phases. A set of eutectic and eutectoid points were found, where transformation reactions and temperatures were identified. The results were compared with results in the literature and good agreements with some differences were found. This study is a step to understand the phase diagram of Ca–Fe-Si system for refining metallugical grade silicon (MG-Si).

Mar 1, 2018

By Khaled M. Mohamed, Michael M. Murphy, Ted M. Klemetti, Heather E. Lawson

"The design of rib support systems in U.S. coal mines is based primarily on local practices and experience. A better understanding of current rib support practices in U.S. coal mines is crucial for developing a sound engineering rib support design tool.The objective of this paper is to analyze the current practices of rib control in US coal mines. Twenty (20) underground coal mines were studied representing various coal basins, coal seams, geology, loading conditions, and rib control strategies.The key findings are: (1) any rib design guideline or tool should take into account external rib support as well as internal bolting; (2) rib bolts on their own cannot contain rib spall, especially in soft ribs subjected to significant load—external rib control devices such as mesh are required in such cases to contain rib sloughing; (3) the majority of the studied mines follow the overburden depth and entry height thresholds recommended by the Program Information Bulletin (PIB) 11-29; (4) potential rib instability occurred when certain geological features prevailed—these include draw slate and/or bone coal near the rib/roof line, claystone partings, and soft coal bench overlain by rock strata; (5) 47% of the studied rib spall was classified as blocky—this could indicate a high potential of rib hazards; and (6) rib injury rates of the studied mines for the last three years emphasize the need for more rib control management for mines operating at overburden depths between 500 ft and 1,000 ft.IntroductionEfforts to improve the stability of underground mine ribs have continued for decades. These efforts by mining professionals around the world persisted throughout the 1990s and 2000s as well, though much of this work focused on rib support methodology and selection of proper support for a specific location. Despite these efforts, it is unfortunate that there has been a continual occurrence of rib-related fatalities in underground coal mines. While overall improvements in rib safety have been achieved, the average fatality rate is still about 1.3 fatalities per year over the last 18 years (Jones, 2014).To manage and control the rib hazard, rib support is used in U.S. coal mines. The current rib support methods for U.S. mines fall into two main categories: rib control based on intrinsic support systems and those based on external support systems. Intrinsic or rib-bolt support requires a roof bolting machine that can install a bolt fixture into the rib. Furthermore, the appropriate level of support needed to control the ribs with an intrinsic-based support system as well as the design parameters for those support systems for various mine conditions have not been established in U.S. coal mines. Furthermore, surface control systems are often an integral part of these support systems and must be considered in the system design."

Jan 1, 2015

By G. E. Willey

F OR many years, only one grade of structural steel has been used in volume in Canada. Its characteristics have not been altered appreciably and its long use speaks well for its performance. This standard grade of structural steel may be bought and specified as C.S.A. G40.4 steel or the American equivalent, A.S.T.M. A7. The principal limitations and requirements of this specification are shown in Table I. Within the last five years there has been a growing awareness among the steel producers and steel fabricators that economic forces are at work which make desirable the availability of new and better grades of structural steel. Competition from other materials has increased. The use of concrete bridges and pre-stressed concrete beams is a prime example. New sources of steel from outside the country have become a threat to the Canadian industry and its high cost-price structure. The need for improved properties in the steel, to make possible technologic

Jan 1, 1962

By Charles Will Wright

This paper has been written to aid the owner of a small gold mine or prospect in preparing a report on his property for the purpose of interesting capital. If an owner can afford to do so, he should employ a mining engineer of recognized standing and experience to examine and report on his property, but many owners of small -mines and particularly of prospects cannot make the expenditure required for this. Further, many of them do not know how to prepare a description which will cover those features of a deposit on which a potential investor promises his opinion as to its worth. If such an owner is convinced that he possesses an orebody of sufficient grade and size to warrant the required expenditure for a thorough investigation and wishes to present his property to prospective investors, then the following suggestions concerning the proper way to sample his deposit, estimate the tonnage of developed and probable ore, and prepare a report may be of assistance.

Jan 1, 1933

By Tell Ertl, Ernest E. Burgh, John R. Wagner

The principal goal of the Oil-Shale Mining Division is to develop the most economical methods and practices for mining oil shale. Experimental work in the mine has not progressed far enough to conduct full-scale breaking tests; therefore, mining season - to October 31, 1945, has been confined largely to problems connected with drilling cost oil shale. Calculations have indicated that commercial production will result in breaking the oil shale; the largest individual turn will be for drilling. This paper is a report on the progress of phase two of drilling research to date; it outlines the development of a successful hard-surfaced rock bit for drilling oil shale.

Dec 1, 1948

By Reza Kamali, Mohsen Bashiri, Hadi Fanisalek

"Nomenclature: A: area (m2), C: heat capacity (WIK), cp: specific heat (J/Kg K), d: internal tube diameter (in), F: correction factor for multi-pass and crossflow heat exchanger, h: convective heat transfer coefficient (W/m2K), k: thermal conductivity (W/mK), L: length (m), m: mass flow rate (Kg/s), W: flow rate, N: number, Q: heat rate (W), R: thermal resistance, T: temperature (°C), U: overall heat transfer coefficient (W/m2K), ;1,,P: pressure drop (Pa), ;1,,T: temperature difference (°C), p: density (lb/ft3), N: number of tube passes, U,: velocity in tubes, iJh: head loss in feet of flowing fluid, Up: velocity in the pipe leading to and from the heat exchanger (ft/sec), µ: viscosity ( cp ), Llpf frictional pressure loss (psi/l 00 equivalent ft of pipe) Subscripts: b: baffle, c: cold, cf counter flow, ex: exchanger, f: fouling, h: hot, i: inlet-inner, ib: inlet baffle, lm: logarithmic mean, m: mean, o: outlet-outer, s: shell, t: tube, w: wall AbstractThe main bottleneck for primary aluminum production industry is dealing with a huge amount of input energy. The fact is that part of provided energy to aluminum production smelters will be lost as waste heat and it never used for aluminum production. One part of waste heat is escaping from the potroom exhaust gases, which was studied for possible recovery in a desalination plant to produce distilled water and the paper was presented in 2011 TMS Annual Meeting. However, it was shown that waste heat recovery plant to produce distilled water is highly profitable but the main fact is that the exhaust gases from potroom are highly corrosive, abrasive and dusty. The main challenge for desalination plant construction, which is using aluminum smelter exhaust gases as the main heat source, is the highly corrosive environment that makes the situation difficult and complicated for equipments design and plant construction. In this paper, we are trying to study a detailed investigation regarding the heat exchangers fouling, corrosion in heat exchangers including heat exchangers' material, how often we need to shut down the plant for maintenance or cleaning, and plant thermal efficiency with considering fouling."

Jan 1, 2012

By M. E. Charles

The use of water flowing as a lower layer to reduce pressure gradients in petroleum pipelines was investigated using 17.5 deg. A.P.I. Lloydminster crude oil in a 1-inch laboratory pipe-line and a 21h-inch field pipeline. The method was found to be very effective in reducing the pressure gradient below that for the oil flowing alone. The factor by which the pres-sure gradient was reduced varied with the percentage of water added, and in general exceeded 10 for water contents ranging from 40 to 60 per cent. Within this range of water content the pressure gradient reduction factor was independent of the oil flow rate.

Jan 1, 1960

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing gypsum mining and crushing methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to a technical discussion and study of the methods employed. The attention of the reader is called specifically to this differentiation so that there may be no misunderstanding of the scope of the cost tabulation. This paper deals specifically with the mining and crushing methods employed by Victor Plaster, Inc., Victor, Ontario County, N. Y. The maximum annual production capacity of this company is 150,000 tons of crushed gypsum. The methods and practices employed arc typical of those followed in the gypsum mines in western New York State. The shaft is, perhaps, the deepest and the thickness of the gypsum mined is above the average for the section.

Jan 1, 1937