Search Documents

By G. F. Colborne, A. Thunaes

"When the Canadian uranium milling plants went into operation during the early 1950's, they utilized flowsheets developed at the Radioactivity Division of the Federal Mines Branch in Ottawa. Since then, numerous process improvements have been made by the Mines Branch, by the operating companies themselves and by other research organizations. This paper will consider uranium milling technology from the standpoint of a new mine operator charged with the responsibility for the design of an economic flowsheet, and will indicate the range of process elements available to him and the testwork required to enable an intelligent decision to be made."

Jan 1, 1968

By James F. McConnell

Federal and State sulfur oxide emission and ambient air quality regulations have been implemented to fulfill the requirements of the Federal Clean Air Act Amendments of 1970. Primary and secondary air quality standards have been established at levels considered necessary to assure the protection of the health and welfare of the public. Standards of performance under this Act have been established to control the rate of sulfur oxide emissions from individual sources so as to protect and to improve the quality of the Nation's air. The new source standards of performance were made rigorous for large coal burning stationary sources. This has had a severe impact on the electric utilities that operate the coal fired steam electric plants which are the largest consumers of the Nation's coal production. States have taken different approaches in State Implementation Plans (SIPS) as approved by the Federal Environmental Protection Agency. Some states, such as Pennsylvania, have chosen to permit moderate SO2 emission rates from existing sources which are not in critical air basins. All are required to meet primary and secondary air quality standards and to limit sulfur oxide emissions from new large stationary sources to a minimum of 1.2 LBS of S02/MMBTU fired. This re- quires a fuel sulfur percentage of about 0.7 for a 12,000 BTU/lb coal. In an effort to develop strategies and technologies to conform to performance standards while continuing and hopefully expanding the utilization of the Nation's coal supply, the electric utilities, the Federal and State regulatory agencies, and other industries and government agencies are considering several alternatives. 1. Natural low sulfur coal 2. Flue gas desulfurization - (FGD) non-regenerative and regenerative 3. Coal gasification 4. Liquefaction and solvent refined coal 5. Fluidized bed combustion 6. Chemical coal cleaning 7. Physical coal cleaning Of these options, only the first and the last can be considered to be widely used in full commercial practice at this time. FGD has certainly demonstrated technical and operating feasibility and is close to being in full commercial practice but it remains to be seen if the large systems under construction are economically and environmentally optimum.

Jan 1, 1975

By S. Klein, M. McLeod, S. Gambino, K. Johnson, E. O’Hara

The Mokelumne Aqueducts Resiliency Project (MARP) involves construction of a 16.5-mile tunnel across the Sacramento-San Joaquin Delta (Delta) to replace the existing surface aqueduct pipelines with more resilient conveyance. The tunnel will be bored in Pleistocene-age alluvium at elevations between 100 to 10 feet below mean sea level. At this depth ground conditions are signicantly stiffer and denser than surcial soils and will mitigate potential seismic harards related to liquefaction ground shaking and cooding that could arise from potentially damaged levees. The heterogeneous soil deposits at tunnel depth consist of interbedded layers of stiff to very stiff clay and silt, and dense to very dense clean sand and silty sand.

Jun 23, 2024

By W. H. Hannay

Introduction The subject matter of this paper will be treated under two heads: (1) experimental work and the development of the purification system, and (2) the operation of the commercial plant. During 1927-28, a two-ton slag-retreating plant was in operation at the smelter for experimental purposes. Details of this operation and of the commercial plant are presented in a paper by G. E. Murray, read before the Annual General Meeting of the Institute in April, 1933 (1). A point which has considerable bearing on the subject of the present paper, and which was not emphasized by Mr. Murray, is the concentration of volatile impurities in the zinc oxide fume produced. The result of the operation of the slag fuming furnace is largely to confine in a closed circuit all the minor constituents of the Sullivan concentrates, both lead and zinc. They pass into the feed of the zinc fuming furnace, with the result that all impurities which volatilize-such as arsenic, antimony, tin, fluorine, etc.-report in the zinc oxide product. The accompanying condensed flow-sheet (Figure 1) will illustrate this. The only outlet for impurities which is not shown is the small tonnage which passes the Cottrell plants. The flow-sheet would indicate the possibility of building up a prohibitive concentration of cathodic impurities in the oxide leaching plant feed. However, after three years' continuous operation this has not occurred. Should this condition arise at some future date, discard of some tonnage of blast furnace slag is indicated. In Mr. Murray's paper, the much greater flexibility of blast furnace operation, due to the slag fuming furnace, is stressed, particularly as to the lead content of the slag. The requirements of our lead refinery call for a bullion containing about 0.70 percent antimony.

Jan 1, 1934

By Clayton M. Rumsey

The U.S. Bureau of Mines investigated prospects and mineralized areas in and adjacent to the Indian Pass and Picacho Peak study areas in 1983 and 1984. The Indian Pass study area contains 33,640 acres and the Picacho Peak study area contains 5,450 acres. The study areas are located in the southeast corner of California and are underlain by Precambrian gneiss, Pre-Tertiary metavolcanic and metasedimentary rocks, and Tertiary volcanic and non-marine clastic rocks. Low-grade gold-silver resources may be present in hydrothermally altered gneiss in the upper plate and altered schist in the lower plate of the Chocolate Mountain thrust fault. The thrust fault is exposed in the study areas for about 3.5 miles west and 5 miles east of Indian Pass. Mineralized zones in the thrust plates were not discovered until 1983. Earlier prospecting explored areas containing minor copper carbonate occurrences in schist and sedimentary and volcanic rocks that are younger than the thrust. Twenty-three mines, prospects, and mineral occurrences inside the study areas and fourteen outs; de were examined for this study. These surficial copper occurrences have been prospected extensively in the study areas; large areas have been scraped, pitted, and trenched by bulldozers. However, they appear to be of limited economic significance. Slightly mineralized zones are in the northwest part of the Indian Pass study area where granite contacts sedimentary and volcanic rocks.

Jan 1, 1986

By Monique Nykamp

"INTRODUCTIONTerminal 46 is located just south of downtown Seattle, and is one of the Port of Seattle’s busiest container terminals. The Terminal 46 Redevelopment Project was undertaken to replace the existing 15-m-wide (50 ft) cranes along the apron with 30-m-wide (100 ft) cranes, which can unload larger, post- Panamax ships. The project included upgrading the existing waterside crane rail with new piles and constructing a new land-side rail behind the sheetpile bulkhead. The new piles had to be installed adjacent to the existing apron without causing damage, which was a signifi cant geotechnical challenge due to the soft soil conditions at the site. An instrumentation program performed during the test pile program evaluated this challenge and allowed for the development of specifi c production pile installation procedures that had the least possible effect on construction costs and schedule. SITE HISTORYThe site lies along the west side of Elliott Bay, north of the mouth of the Duwamish Waterway. Prior to development, this area was part of the tide fl ats where the Duwamish River drained into Elliott Bay. Prior to 1970, there were several existing timber piers and structures in the area. In the 1970s, the Port of Seattle constructed a 900-m-long (3,000 ft), 30- m-wide (100 ft) apron to support fi ve, 15-m-wide (50 ft) container cranes. The contained backland area was then fi lled with dredged spoils (sand and silt with organics) and the upper 5 to 20 m (16 to 65 ft) backfi lled with sand and gravel.The existing apron was constructed using 0.4 m (16 in) octagonal prestressed concrete piles to support the precast concrete deck and crane rails. The pile-supported bents were spaced at 6.1 m (20 ft), center-to-center, along the longitudinal direction. Pile lengths typically varied from about 20 to 40 m (65 to 130 ft) with 15 to 26 m penetration below mudline (50 to 85 ft penetration). The slope below the apron was constructed at about 1.75 horizontal to 1 vertical to allow for suffi cient water depth for cargo ships. In most areas, a riprap buttress was placed at the toe of the slope. A typical cross section of the apron is shown on Figure 2.Several stability, settlement and pile driving issues arose during the original construction of T-46 (Pita, 1983). Reportedly, movement of the submarine slope occurred during pile driving, resulting in settlement behind the bulkhead. Pile driving reportedly caused settlement of adjacent piles. In addition, some piles were “running” (dropping quickly under one hammer blow) during installation."

Jan 1, 2007

By Monique Nykamp

"INTRODUCTIONTerminal 46 is located just south of downtown Seattle, and is one of the Port of Seattle’s busiest container terminals. The Terminal 46 Redevelopment Project was undertaken to replace the existing 15-m-wide (50 ft) cranes along the apron with 30-m-wide (100 ft) cranes, which can unload larger, post- Panamax ships. The project included upgrading the existing waterside crane rail with new piles and constructing a new land-side rail behind the sheetpile bulkhead. The new piles had to be installed adjacent to the existing apron without causing damage, which was a signifi cant geotechnical challenge due to the soft soil conditions at the site. An instrumentation program performed during the test pile program evaluated this challenge and allowed for the development of specifi c production pile installation procedures that had the least possible effect on construction costs and schedule.SITE HISTORYThe site lies along the west side of Elliott Bay, north of the mouth of the Duwamish Waterway. Prior to development, this area was part of the tide fl ats where the Duwamish River drained into Elliott Bay. Prior to 1970, there were several existing timber piers and structures in the area. In the 1970s, the Port of Seattle constructed a 900-m-long (3,000 ft), 30- m-wide (100 ft) apron to support fi ve, 15-m-wide (50 ft) container cranes. The contained backland area was then fi lled with dredged spoils (sand and silt with organics) and the upper 5 to 20 m (16 to 65 ft) backfi lled with sand and gravel.The existing apron was constructed using 0.4 m (16 in) octagonal prestressed concrete piles to support the precast concrete deck and crane rails. The pile-supported bents were spaced at 6.1 m (20 ft), center-to-center, along the longitudinal direction. Pile lengths typically varied from about 20 to 40 m (65 to 130 ft) with 15 to 26 m penetration below mudline (50 to 85 ft penetration). The slope below the apron was constructed at about 1.75 horizontal to 1 vertical to allow for suffi cient water depth for cargo ships. In most areas, a riprap buttress was placed at the toe of the slope. A typical cross section of the apron is shown on Figure 2.Several stability, settlement and pile driving issues arose during the original construction of T-46 (Pita, 1983). Reportedly, movement of the submarine slope occurred during pile driving, resulting in settlement behind the bulkhead. Pile driving reportedly caused settlement of adjacent piles. In addition, some piles were “running” (dropping quickly under one hammer blow) during installation."

Jan 1, 2007

By Scott Rosenthal

?EMESRT History ?Design Philosophies (DP?s) ?Industry Successes ?Participation Thinking Differently Earth Moving Equipment Safety Round Table ? Use a critical mass to influence Marketing ? Define ?Problems?not ?Solutions? ? Leave the OEM designers to develop solutions Work within the companies to improve purchasing

May 1, 2010

By William J. Almas

Operating uranium mill tailings containment and mill decommissioning activities are regulated by the Nuclear Regulatory Commission (NRC) and the Environmental Protection Agency (EPA) through numerous regulatory mechanisms. Reduction of radon emissions from tailings disposal areas, remedial actions to return groundwater to baseline constituent concentrations, and 200-to 1,000-year stabilization of tailings are major focus areas of regulation. The cumulative economic impact and uncertainty associated with regulation are very significant and will hinder future development of uranium milling facilities.

Jan 1, 1991

By Cheng Li, Yanlei Wang, Lingrui Kong, Jianxin Tang, Fang Yuan

Coal mined-out areas have a significant impact on mining safety and affect the pressure distributions of neighboring coal faces. The PFC3D software is used to study the goaf mechanical characteristics, and the core loading test verifies the rationality of the numerical simulation method. The results from the numerical modeling showed that the void ratio, particle size ratio, and particle size distribution of the rock particle sample (RPS) had a significantly remarkable influence on the compression deformation characteristics of the rock block. The parallel-bond tensile strength and parallel-bond cohesion had a notable impact on the compression deformation traits of the rock block only when the axial stress level was lower than 12 MPa. By contrast, when the axial stress exceeded 5 MPa, the effective modulus significantly influenced the compression deformation features. However, the stiffness ratio, loading rate, and parallel-bond friction angle had almost no effect on the compression deformation characteristics. Furthermore, when the stress level was less than 10 MPa, the stress–strain curves from the rock core samples’ numerical simulation and loading tests were approximately linear. In addition, the Pearson correlation coefficients of the stress–strain curves suggest that the goaf zone’s core numerical simulation results had a robust correlation with the loading test results. The findings of this study can serve as a reference for the field application of PFC3D software and safety assessments in goaves.

Jan 18, 2022

By R. Sellaro, E. Sarver

It has long been understood that extended occupational exposures to respirable mine dusts can lead to chronic lung disease. In underground coal mines, coal workers pneumoconiosis (CWP) and silicosis are major concerns. While many efforts have been made with the aim of understanding the mass-based concentrations and silica contents of respirable dusts under a variety of mining conditions, little research has been completed in characterizing dust at the individual particle level (by composition, size and shape). This study employed scanning electron microscopy with energy dispersive x-ray (SEM-EDX) to analyze dust samples collected from an underground coal mine in Central Appalachia. The results indicated that particle characteristics can vary widely between locations, though many trends might be explained based on knowledge of mining conditions. A continuous personal dust monitor (CPDM) was also used during the collection of some samples to determine respirable dust concentrations, which were compared against estimated concentrations based on the particle-level analysis.

Jan 1, 2014

By R. S. Norman

The objective of this program was to select approximately 100 acoustic materials for flammability evaluation. Noise control programs have been initiated on several types of mining equipment and vehicles which can be used in underground coal mines. Often, the materials which are used in these noise reduction programs have not been tested for flammability properties according to the same reference standard. During this program a variety of materials were selected for measurement according to ASTM E-162 procedures. A radiant heat energy source was used to measure flammability properties of 15.2 x 45.7 cm. samples. In the absorptive materials category, 45 percent of the materials tested had a flame spread index of less than 25. For barrier, damping, and isolation materials the corresponding values were 40, 43, and 9 percent.

Jan 1, 1979

By Robert L. Mentch

CADMIUM is one of the metals apparently destined to remain relatively scarce. The en tire supply of primary cadmium is recovered as a byproduct, concurrently with the treatment of ores of other metals. Development of the cadmium industry is attributed to metallurgical improvements in the zinc industry; output depends almost wholly upon zinc production. Cadmium is a metal of specialized uses where its superior performance has developed a strong, expanding demand. The supply, however, has been relatively unresponsive to price because of its byproduct nature. Cadmium's outstanding properties would assure it a manyfold greater market if more were available at lower prices.

Jan 1, 1958

By G. K. Nimal Subasinghe

The performance of Knelson Concentrators (KC) used in gravity gold circuits often rely on manufacturers recommendations for selecting operating parameters such as, fluidising water flow rate and cycle time. These parameters are not only dependent on the machine parameters but also on the feed characteristics such as, size distribution of the gold and gangue particles and the composition of its constituent minerals. Particles entering a KC experience a centrifugal acceleration due to the high bowl rotational speeds. The required centripetal force to maintain a circular orbit is provided by the fluid drag force created by inwardly moving fluidising water and the Bagnold?s force arising from the particle/particle collisions. When the fluidising water flow rate is low particles move towards the outer rim of the bowl forming a packed bed within the grooves. On the other hand, if the fluidizing water flowrate is high the bed expands and some particles would move towards the centre of the bowl and gets carried to the tailings stream, thereby reducing the amount of material retained within the grooves of the bowl. Based on a force balance on a particle captured within the KC, a criterion which can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It has been shown that this criterion may be used to demarcate the transition of the bed from a packed-bed state to a fluidised state depending on the fluidizing water flowrate. By identifying the conditions for the optimal expansion of the bed comprising different constituent mineral particles, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. It was also observed that the accumulation of valuable mineral in the bowl takes place by the displacement of the gangue particles in the bed by the incoming heavy mineral particles. The kinetics of this segregation process was also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build up of heavy mineral reaches a maximum which could be used to identify the optimal cycle time. In this work, the suitability of the above model in optimizing the performance of a KC have been reviewed. Also the necessity and merits of testing an unaltered feed samples in a larger KC as op-posed to the commonly adopted GRG test has been discussed.

Jan 1, 2014

By L. M. Pidgeon

"Part I. - PrinciplesIntroductionIf the oxides of the metals are listed in decreasing order of the magnitude of their heats of formation, the list appearing in Table 1 will be formed. It will be apparent at once that this is essentially the well-known electrochemical series (Table li). The metals at the bottom of the list exhibit great stability and are attacked only by the most violent of chemical reagents. Higher on the list, the metals become more reactive until, at the head of the list, the metals lithium and calcium are unstable in moist air.The reactive metals to be considered lie above manganese. In this group will be found familiar and abundant metals such as aluminium and magnesium, the unfamiliar yet abundant metal titanium, the rare and mysterious metal beryllium, and others of greater or less interest.While these metals exhibit properties as unlike as those of uranium and magnesium, they have in common a specialized and difficult extractive metallurgy. They form compounds of great stability, and their reduction is to varying degrees difficult. The position of a metal in Table 1 (and more particu1arly its position in the free energy column) gives a numerical value to this property.Oxides with low free energies of formation may be reduced with great ease; thus silver and mercury may be produced from their oxides by simple heating in air.Lead, iron, and zinc may be separated from their oxides by heating with carbon to moderate temperatures. Magnesium oxide, on the other hand, .requires a high temperature and very special conditions before it will yield magnesium metal."

Jan 1, 1950

By J. R. Rau

While refuge chambers are common place in most underground mining projects, there are different philosophies as to what life support systems are to be considered and how these systems are to be applied. Case studies in the underground mining industry have examples of emergencies where the external compressed air and power supply to the refuge chamber were compromised due to proximity of services to the fire location. In 2005, The Department of Industry and Resources, Western Australia, drafted guidelines that listed specific requirements for refuge chambers which included a secondary life support system that would operate independently of external sources. The objective of this document is to examine what critical life support systems are essential for safe entrapment in the event of an emergency and to examine considerations for their application.

Aug 1, 2013

By M. A. Vasina, I. A. Matveeva, E. A. Naumova, V. V. Doroshenko, N. A. Belov

"Using the calculated (Thermo-Calc software) and experimental methods (SEM, TEM, EMPA, DSC, XRD, etc.) the phase composition, structure and hardening of aluminium alloys of the Al-Ca-Zn-Mg system were studied in the following range: 2. 5%Mg, up to 10% Ca, and up to 14% Zn (wt%). Fragments of this quaternary phase diagram in the aluminium corner were constructed, including the liquidus surface, as well as some vertical sections. It was shown that the relatively large amount of zinc enters in the Ca-containing phase, which formula can be described as (Al,Zn)4Ca. An increase of Zn content leads to formation of Al4Ca primary crystals at lower concentrations of calcium. The eutectic (Al)+(Al,Zn)4Ca has a fine structure and aluminide particles are capable to spheroidization during the heat treatment at temperature 500 C. The maximal level of hardness observed on calcium containing alloys was higher than 200 HV, what gives the reason to expect good strength properties. With an example of an Al-9% Zn-2,5%Mg-3,5% Ca model experimental alloy based on the (Al)+(Al,Zn)4Ca eutectic, a principal possibility of manufacturing thin rolled sheets was demonstrated.INTRODUCTION Aluminum alloyed with calcium was first studied in 1970-80s by such authors as Piatti (1976), Moore (1978, 1980), Il'enko (1985), Swaminathan (1990), and Perez-Prado (1997) as superplastic materials. In particular, the alloy systems Al-Ca-Zn were studied (Il'enko, 1985, Swaminathan, 1990, Perez-Prado, 1997). For some time there was no new published works concerning the aluminum-calcium alloys. During the last years many works were published dedicated to the calcium alloying of magnesium alloys (Kim, 2011; Xu, 2011; Aljarrah, 2008; Bakhsheshi, 2014). This urged the authors (Belov, Naumova & Akopyan, 2016) to start studying cast and wrought aluminum-calcium alloys for construction (2008–2014). There is almost no information in the literature concerning triple and more complex diagrams of the aluminum-based system states with calcium and other elements. In recent work, parts of the state diagrams are plotted for the aluminum angle zone: Al-Ca-Mg-Sc (Belov, Naumova & Bazlova, 2016), Al-Ca-Ni-Sc (Belov, Naumova & Bazlova, 2017), Al-Ca-Si-Sc (Belov, Naumova & Akopyan, 2017) and others. Special attention was paid to the study of the system Al-Ca-Zn-Mg (Naumova, 2017). Based on this system creation of advanced extra-high tensile alloys is planned. Wrought extra-high tensile alloys series 7??? based on the system Al-Zn-Mg-Cu are well studied."

Jan 1, 2018

By AIME AIME

THE best meeting ever held, was the opinion expressed by a number of those who attended the annual meeting of the Institute in New York, Feb. 18 to 21, and there was an atmosphere of friendliness and good fellowship about it that fully justified the feeling. In numbers it was not quite so large as last year and unless the Engineering Societies should build for themselves a new building it is probable that no meeting can be larger, in respect to numbers, than that held in 1928, which was only made possible by the circumstance that the eighth floor of the building happened to be, temporarily vacant at the time. The number of rooms available for -sessions that were provided when the building was built long ago proved inadequate, and it is only by the expedient of obtaining the temporary use of the board and committee rooms of other societies that it is possible to arrange for the over 40 sessions that must be spread over the four days of the meeting. The-fifth floor, where. a buffet lunch is served each-day, has reached its full capacity and it seems quite evident that any future development of Institute meetings must be along the lines of quality, not size.

Jan 1, 1929

By A. B. Kinzel

ALTHOUGH the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approxi-mately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cementite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consider-ation of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:1 C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown in Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850° C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the

Jan 1, 1934

By Francis Martino

Just as coal producing mines are faced with various handicaps which control the quantity of coal produced and sold, the subsequent user of that product is faced with parameters that impact the optimum utilization of coal. Traditionally, the industry focused on the quantity of mineable coal in a reserve. The mine planning development was primarily concerned with two important criteria: (1) safety and (2) the productive efficiency in a quest to produce the lowest cost coal.

Jan 1, 1982