Search Documents

By Gerhard Meyer

A new instrument for the determination of iron., zinc, calcium, and other metals independently directly in the fumes emitted from steelmaking processes is described. Based on the well- accepted method of X-ray fluorescence, the instrument can detect numerous metals simultaneously in the fume as well as report their concentration on a mass per unit time basis real time to a control room computer. The instrument mounts on the wall of the fume duct and can., via a small opening, directly view the hot exhaust plum inside the duct. The concentration of metal in the fume over time has been shown to change dramatically depending on process variables. Variables such as oxygen flow rate, lance height and nozzle configuration., slag condition., and episodic scrap addition can affect the presence of metal particles and fume in the exhaust. An analysis response time of 6 seconds enables better control of the steelmaking process thereby conserving primary resources and reducing environmental impact.

Jan 1, 2001

By J. W. Tsai

Both diamond crystals and diamond films were grown on silicon and copper substrates using a methane/hydrogen gas mixture as a precursor with thermal CVD techniques at low pressure environment. In addition to diamond particles, other crystalline phases including graphite and aluminum silicon carbide were observed on the substrate surface. ?The grown materials were analyzed with X-ray diffraction, electron microscopy, Auger electron spectroscopy and optical microscopy. Most synthesized diamond crystals were twinned. The flow rate of reactant gases, substrate nature, substrate temperature, decomposition temperature of the precursors, total pressure of reaction chamber, methane/hydrogen ratios and other possible parameters were varied during the growth processes, and the significant effects of these factors on nucleation and growth rate were evaluated.

Jan 1, 1989

By Eoghan T. M Doyle

Oxide mixtures of nickel (NiO), cobalt (COO) and chromium (Cr203) were prepared with graphite in stoichiometric amounts and the powder mixtures were compacted to produce cylindrical pellets. The composition of chromium oxide in these mixtures were varied. Pressed pellets were reduced in a flowing stream of argon-4% hydrogen gas (500 ml/min). Both slow and rapid heating methods were adopted to raise the temperature of a pellet during reduction of oxides to form superalloy powder. The reduction temperature was varied between. 1523 and 1623K. The effect of heating rate and niobium oxide addition on the microstructure of the superalloy produced was studied by using ordinary light and scanning electron microscopes. New phases formed as a result of reduction were identified by X-ray powder diffraction technique. The mechanism of reduction of oxides together with the microstructure of NiCrCo alloy are discussed. The thermodynamics of formation of ternary alloy phase is elucidated on the basis of binary phase equilibria and Gibbs free energy of mixing data for the constituent alloy compositions.

Jan 1, 1992

By Anestis Vlyssides, Elli Maria Barampouti, Sofia Mai, ?postolos Vlyssides

"A new anaerobic reactor variation, the UASB/CO2-stripper reactor was conceived. It consisted of a conventional UASB reactor that recirculated the biogas produced. The sludge characteristics of this system were examined when treating high strength wastewater. From the data collected, it was obvious that the UASB/CO2-stripper system can satisfactorily operate at higher loading rates (25 g COD·L-1·d-1). A pronounced effect on the quality of the granular sludge was observed. The VSS/TSS ratio decreased sharply. A considerable decrease in the mean granule diameter was observed, while the specific gravity of the granules increased. The sludge bed porosity increased significantly leading to a considerable expansion of the sludge bed. These changes in the sludge properties led to a gradual shift of the system towards a fluidized bed process as far as its hydraulic characteristics were concerned.IntroductionIn recent years energy considerations and environmental concerns have increased the interest in direct anaerobic treatment of industrial wastes. The anaerobic method of waste treatment offers, under the present circumstances, a number of significant advantages with trivial or more serious drawbacks over other treatment methods. The major obstacle to the application of the process for this specific purpose is perhaps the difficulty of extending it to a stable and simple operational form. A number of reactor configurations has been developed leading to high biomass concentrations, e.g. the contact process, the filter reactor, the UASB reactor, and the fluidized bed systems, but the process stability problem still remains [1].A prime objective in the operation of anaerobic waste treatment process is the maintenance of a proper pH range. Thus, a possible solution to the process stability problem could be obtained by increasing alkalinity in the anaerobic systems. Therefore, the main objective of this paper is to present and evaluate the results of a system (UASB/ CO2-stripper) with increased alkalinity concentrations."

Jan 1, 2008

By C. W. Whitten

Solis from an abandoned Pb battery processing facility were characterized prior to the selection of the extraction technique. Reflected light microscopy and electron beam methods were used to locate Pb-bearing phases and to quantify the compositions of the phases. It was found that the soils are composed primarily of quartz and feldspars with minor amounts of iron and titanium oxides. Lead is primarily present as an oxide or sulfate that is associated with the silicate minerals. Specific phases identified were PbO; Pb02; cerrusite, PbCO3; angleslte, PbSO4; galena, PbS; and magnetoplumbite, 2PbO3Fe2O3; or plumboferrite PbO2Fe2O3?

Jan 1, 1989

By Jinfu Xu, Youqing Cao, Yuting Lv, Hang You, Peng Jiang

"In present work, we reported the fabrication of composites consisted of M42 powder metallurgy high speed steel and 45 steel at one step via spark plasma sintering (SPS) technology. The interface microstructure, compositions and microhardness with the interface forming mechanism were investigated. The results show that the morphology and microhardness within the M42/45 steel interfaces exhibit a gradient distribution. The interfaces possessed a transition layer up to 10.2 ?m with few distortions and microcracks. The formation of M42/45 steel interfaces were driven by both fusion and diffusion processes. The former one was primary at the early sintering process, while the later one becomes dominant over the followed sintering process.IntroductionPowder high-speed steels have been widely used in cutting tools, cold-hot tools and dies, as well as in cut materials and structure parts with wear resistance and high-temperature resistance, due to its high hardness, good wear resistance, desirable cutting toughness and favorable hot hardness [1-2]. For materials of some parts in practical production, not only the favorable toughness is required to resist the impact action, but also the high hardness and exceptional wear resistance are demanded. According to the functional requirements and working conditions, bimetal composite materials are prepared in a certain mode, proportion and distribution, by designing two metals with different chemical and physical properties [3-6]. Considering the composites exhibit different properties in different positions of the parts with a combination of the advantages of two metals, they can obtain enhanced properties that the single one can not achieve."

Jan 1, 2012

By Honggang Zhong, Tan Yi, Qijie Zhai, Zhao Dan, Xinping Mao, Huigai Li

"The influence of superheat degree on the distribution and volume content of inclusions were studied in 65Mn thin slab produced by compact strip production(CSP) in Zhujiang Steel in China, The results showed that the diameters of inclusions are mainly less than 5µm. Most of the inclusions gathered at the 1/4 thickness direction for the thin slab of 27? superheat degree, compared with the center position for that of 37?. There are more inclusions larger than 50µm in the low superheat samples, which is caused by the short floating time. In addition, the inclusions were observed and analyzed by metallurgical microscope, SEM and EDS in order to ensure their composition, type and further find their source. It was find that the types of these inclusions mainly are Al2O3, SiO2,CaO and their composites, a few of them are TiN and MnS.IntroductionIt is well known that inclusions have a great impact on the strength, plasticity, fracture toughness, cutting performance, fatigue property and corrosion resistance of steels. Especially, with the demand for thinner slab, the cleanness is increasingly becoming more significant as a quality criterion[1]. High manganese and carbon steels not only demonstrate high strength but also proper plasticity. There are many problems unsolved for 65Mn steel as a result of the low solidification rate, bad thermal strength, crack sensitivity and low casting temperature[2,3].The superheat of the molten steel has a great impact on the erosion of refractory lining, molten steel fluidity and non-metallic inclusion behavior[4]. The serious erosion situation of ladle lining, nozzle and casting tundish will give rise to more inclusions at a high superheat. Meantime higher superheat will make second dendrite arm spacing coursing and element segregation which lead to inclusion, bubble formation and shrinkage cavity. On the contrary, it is hard for non-metallic inclusions to float up with a low superheat value. Inclusions of 65Mn steel, which produced in different superheat condition by CSP, were studied for the sake of higher slab properties including statistics and EDS analysis."

Jan 1, 2012

By Motohiro Horiguchi, Kazuo Ichii, Toshio Oishi

"As a fundamental study to prepare copper-based alloys with rare earths (RE: La, Gd, Nd, Ce and Y) without any inclusions, the solubility of rare earth in liquid copper was experimentally determined. Liquid copper alloys were equilibrated with carbon and rare earth carbide in a graphite crucible in an argon atmosphere at 1523-1873 K.Solubilities of rare earth in liquid copper were determined by approaching the equilibrium values from both the lower and the ·higher concentrations than those expected· in the preliminary experiments. They were expressed as a function of temperature. Carbon in Cu-RE alloy was also analyzed and thermodynamically discussed.IntroductionOver the past several years, the demand for highly conductive and high strength copper-based alloys, such as Cu-Cr, Cu-Zr and Cu-Cr-Zr for use in electronic materials has increased.1 -7 These alloying elements are very reactive and easily oxidized to form oxide inclusions during melting. To avoid the oxide inclusions, it may be effective to utilize the strong reducing power of carbon in conditions under which no carbides form.In this study, to provide fundamental data for producing Cu-RE( rare earth) alloys without any inclusions, the solubility of rare earth in liquid copper in equilibrium with .carbon .was determined and discussed on the basis of the experimental results and the thermodynamic data.ExperimentalSample preparation for equilibrium experimentsOxygen-free copper (99.99%), lanthanum (99.9%), gadolinium (99.9%), neodymium (99.9%), cerium (99.9%) and yttrium (99.9%), and their oxides were used as starting materials.Each rare earth carbide was prepared by mixing rare earth oxide with carbon, which is a little more than the stoichiometric composition, pressing it into a tablet form and sintering at about 2000.K for 20 ks in a vacuum furnace using a graphite crucible. Powder X-ray analysis showed that only the carbon and rare earth carbide (REC2) was present in each sample.Cu-RE mother alloys (5-20 mass % RE) were prepared beforehand by mixing metallic rare earth with oxygen-free copper, and melting in an electric arc furnace."

Jan 1, 2000

By Dianyuan Dang, Guihong Han, Wenjuan Wang, Tao Jiang, Yanfang Huang

In this study reduction kinetics and swelling behaviors in "two-step process” were investigated by weight-loss technique and visualizing physical changes of pellet. Results showed that reduction degree (r) increased with increasing temperature and time. According to the dynamic calculation, when reduction temperature was lower than 1000°C the reduction process was controlled by chemical reaction with apparent activation energy of 72.27 kJ/mol. When reduction temperature was higher than 1000 , the equation of t/[1-(1-r)1/3] against [1+2(1-r)-3(1-r)2/3]/[1-(1-r)1/3] followed straight lines, demonstrating that reduction was mixed-controlled. Swelling experiments indicated that the maximum swelling index increased with the increase of reduction temperature and CO content.

Jan 1, 2016

By Yuanbo Zhang, FENG ZHOU, Guanghui Li, Zhengwei Yu, RuijunWang, Tao Jiang

Composite agglomeration process (CAP) of iron ore fines has been proved an effective route for ironmaking burden production, and is characterized by low the fuel consumption and high the productivity compared with the traditional sintering process. Sintering behavior of pelletizing feed in CAP has not been studied fully yet. In this study, individual pellet and simulated CAP cells were roasted under the simulated sintering conditions. The compressive strength, FeO content and microstructures of roasted samples were investigated. The results show that pelletizing feed either from magnetite ore hematite concentrate can be indurated under the conditions of conventional iron ore sintering. Hematite pelletizing feed has better sintering property than magnetite pelletizing feed. Pelletizing feed consolidation in CAP cells is identical to the individual pelletizing feed, but the strength of CAP cells is much higher than the individual pelletizing feed. Higher basicity in both pelletizing feed and matrix feed is beneficial to the strength of CAP cells. Individual strength of pelletizing feed is not the decisive factor in CAP as the pelletizing feed has been embedded into the matrix with high basicity and formed an organic whole. The main chemical compositions and basicity of pelletizing feed and basicity matching with matrix feed is important.

Jan 1, 2015

By S. Malinov, J. J. McKeown, W. Sha, S. McShane

"A model is developed for prediction of fatigue stress life S-N diagrams for Ti-6Al-4V alloy at different conditions, using Artificial Neural Network (ANN). Different factors which have influence on the S-N diagram are involved as input parameters of the NN, namely microstructure, environment, texture, test/work temperature, surface treatment and stress amplitude. As the output the S-N fatigue diagram is simulated and plotted.The model is based on standard multilayer feedforward neural network. The NN is trained with a comprehensive data set collected from the literature, using Levenberg-Marquardt training algorithm in combination with Bayesian regularisation. A very good performance of the trained Neural Network is achieved. Good correspondence between ANN"" prediction and experimental S-N diagrams is observed. Using the model S-N diagrams for different conditions are predicted and analysed. Graphical User Interface is developed for use of the model. We believe that the model will be important for practical applications in solving various problems on fatigue behaviour of the titanium alloy.IntroductionTitanium and its alloys have an increasing range of applications due to their very good combination of mechanical properties, corrosion and erosion resistance. They are currently finding widespread applications in many industries due to their desirable and versatile properties. Most important among the alloys is Ti-6AI-4Y. Jet aircraft manufacturers are the principal 'consumers of Ti-6Al-4V and it is often specified for critical parts, the failure of which could result in the loss of an entire system. A generic class of Ti-6AI-4V has been developed over the past years and it has become the best understood of all the titanium alloys. The advantages of titanium alloys include: (i) low densities, giving very attractive strength to weight ratios allowing lighter and stronger structures; (ii) superior corrosion and erosion resistance in many environments; (iii) high temperature capability. Although the titanium materials are still considered as expensive materials, for many applications the cost of titanium alloys can be justified on the basis of their desirable properties."

Jan 1, 2001

By Jiang Fan, Liu Shi, Wang Haigang

Winter-time natural convection in gravel embankments has been suggested as a technique to provide passive cooling and thereby avoid thaw-settlement of roadways located in permafrost areas. Numerical simulation by finite volume method on the proposed model is perf9rmed using the software FLUENT. A gravels model, in which the embankment is composed of stones and air, has been adopted to investigate the temperature and velocity fields in embankment. Simulation results show that in summer, a weak clockwise circulation of the pore air extending throughout most of the embankment. The pore-air motion is very weak which results in relatively straight horizontal isotherm lines. And heat transfer is mainly maintained through conduction. But in winter, pore-air velocities are higher and multiple vortexes are formed in the embankment. Natural convection then becomes the dominant influence on the isotherm shapes within the embankment. As a result of low ambient temperatures exerted on the embankment surface during winter months, an unstable air density gradient develops within the embankment. This convection increases the heat flux out of the embankment. Therefore, the winter-time convection can further reduce the temperature of the foundation soil beneath the open-graded embankment. In addition, the effects of the size of the stones within the embankment have been analyzed and compared in the gravel model. It shows that in winter, 200mm stones lead to stronger vortexes in the embankment compared with those of 60mm stones. Consequently, the zone oflow-temperature beneath the embankment is extended.

Jan 1, 2004

By Baokuan Li, Qiang Wang, Zhu He

"A mathematical model has been developed to investigate the magnetohydrodynamic (MHD), thermal, and solidified behavior in electroslag remelting process. Based on the finite volume method, a multiphase coupling MHD approach is employed to investigate the droplet formation as well as movement in molten slag under the action of an alternating current. The VOF formulation is adopted for interface tracking. The electrical potential method is adopted for the electric current and magnetic field. The Electromagnetic force and Joule heating are recalculated at each time step and then is implemented in the momentum and energy equations as a source term, respectively. Moreover, solidification of the metal is described by an enthalpy-based formulation, while the mushy zone is treated as a porous medium with porosity equal to the liquid fraction. The model is used to investigate the effect of electrode tip shape on MHD, thermal, and solidified behavior and provide valuable information.IntroductionElectroslag remelting (ESR) process has been used widely to produce high-performance alloys dedicated to critical application, such as hot work tool steels, nickel base alloys, the manufacture of components in aerospace and landbased turbines, etc. Figure 1 shows a schematic diagram of ESR process including a consumable electrode, a molten slag pool, a liquid metal pool, a solidified ingot, and a water-cooled mold. Alternating or direct current flows from the electrode to the water-cooled baseplate through the high resistivity calcium-fluoride-based molten slag which result in Joule heating and Electromagnetic force (EMF). Part of the Joule heating melts the electrode and the droplets travel through the slag and accumulate the liquid metal pool. The electrode is continuously advanced into the slag as it melts to build up an ingot of improved structure and composition by controlled solidification and chemical refinement. The metallurgical properties of the remelted ingot are really related to the solidification structure, which strongly depends on magnetohydrodynamic, thermal, and solidified behavior in the molten slag, liquid metal pool, and mushy zone."

Jan 1, 2014

By S. Yin, A. Bogno, H. Henein, P. Natzke

Impulse Atomization (IA) (a single fluid atomization technique) was used to rapidly solidify Al- 4.5wt%Cu and Al-4.5wt%Cu-0.4wt%Sc under argon atmosphere. In addition to the IA-generated droplets, the same technique was used to produce strips by Spray Deposition (SD) of the same alloys on a copper substrate with and without oil coating. The rapid solidification microstructures were analyzed using Scanning Electron Microscopy (SEM). From the SEM images, the amount of eutectic and the secondary dendrite arm spacing (SDAS) were measured. These SDAS results lead to the estimation of cooling rate. The eutectic fraction coupled with the metastable extension of the solidus and liquidus lines of Al-Cu (Sc) phase diagram lead to the estimation of primary and eutectic undercoolings. A comparison of the solidification path of the droplets and the strips was done as well as the analysis of the effects of scandium.

Jan 1, 2015

By Zhihao Yue, Honglie Shen, Yahui Teng, Ye Jiang

"In this paper, manganous nitrate [Mn(NO3)z] was used to assist the etching of silicon wafer in hydrofluoric acid (HF) for the antireflective application, and alumina (Al2O3) layer was deposited on the surface of the etched sample by atomic layer deposition method for further antireflection. The surface morphological and compositional studies of these samples were performed by scanning electron microscopy attached with an energy-dispersive X-ray spectrometer. The surface reflectance measurements were carried out using UV-Vis-NIR spectrophotometer. Binary structures of pyramids and nanopores were obtained by etching the alkaline textured monocrystalline silicon wafer in HF and Mn(NO3)z mixed solution for not more than 15 min. But excessive increase of etching time of up to 30 min resulted in the whole destruction of pyramids. The average reflectances of the 5-min-etched sample before and after being coated with 75-nm-thick Al2O3 layer are 4.62% and 3.47% in the range of 200-1000 nm, respectively.1. IntroductionAs we know, the reflectance of silicon wafer after being sliced is so high that the maximal photoelectric conversion efficiency of silicon based solar cells is limited. Therefore, alkaline texturization process was used for silicon solar cell in industrial production. But the reflectance of this alkaline textured wafer is still greater than 10% and this process can only be used for monocrystalline silicon solar cell."

Jan 1, 2013

By Young-Sool Jin, Heung Nam Han, Hong Joon Kim, Jae Kon Lee

A mathematical model was developed considering non-symmetric cooling' and stress distribution in both thickness and width direction of strip on a run-out table of hot strip mill. In order to solve a transient heat transfer equation including the heat evolved from phase transformation, a finite element method coupled with thermodynamic and kinetic analyses was applied. The heat capacity of each phase and heat evolution due to phase transformation were obtained from the thermodynamic analysis of the Fe-C-Mn-Si system based on a sub lattice model. The phase transformation kinetics of the steels was derived by using an inverse additivity technique with continuous cooling experiments. Heat transfer coefficients of strips on the run-out table were, by applying an inverse method, determined from the actual mill data under various cooling conditions. As for the stress analysis, the density change of strip due to cooling and phase transformation, and the transformation superplasticity were considered. A 90nstitutive equation for the transformation superplasticity, which is related to the phase transformation kinetics and the internal stress due to the density change of strip, was applied. A finite element method was adopted to calculate the deformation behaviour of strip on a run-out table of hot strip mill. Using the models, the temperature-phase-deformation history and distribution of a strip on the run-outtable was calculated.

Jan 1, 2001

By Jiangwei Shen, Cong Wang, Haibin Zuo

The research on the formation of Silico-Ferrite of Calcium and Aluminium (SFCA) in the process of cooling and solidification is rarely reported. The crystallization process was observed by using scanning electron microscopy (SEM) and optical microscope in this paper. The effect of different cooling system on the microstructure and phase composition of the sinters was investigated to obtain the appropriate cooling rate to improve the metallurgical properties of sinters. The experimental results show that the crystallization of calcium ferrite is getting better when the cooling rate is decreased from water quenching to cooling in the air. There are a large number of hematite phases with interconnected crystal structure in the sample cooled in the air. In the case of the compressive strength, it was determined by the mineral composition and pore structure, higher SFCA and hematite contents in sinter cooling in the air lead to a higher strength. Glass phase in the water quenching sinter was the major reason for the lowest strength. High porosity contributes to a decrease in compressive strength for the sinter cooling in the furnace. Therefore the air cooling was the appropriate cooling rate to achieve high quality sinter under this experimental condition.

Jan 1, 2016

By Nathanael Hudson, Ruel A. Overfelt, Sushil H. Bhavnani

"In the aerospace and automotive industries, complex shapes exist which require casting. The problem with these cast parts is the empiricism required to develop the casting process and the accompanying time and expense to develop that process.There has been an interest in using fluidized beds to allow molding sand to better encapsulate the complicated surface geometries of lost foam patterns. Fluidization coupled with a mixing jet helps to homogenize the sand through stirring and may improve the integrity of the casting.At issue is the hydrodynamics of the sand and air around the foam pattern. The commercial package PHOENlCSTM is used to simulate the flow around the pre-casting foam geometry. Employing a two fluid approach, each component is considered a fluid that interpenetrates the other phase. To this end, the kinetic theory of granular 'flow for the sand phase was incorporated into the re-compilable PHOENlCSTM code.The results of this study consist of time-averaged void fraction patterns, with voidage being defined as the fraction of air in the mixture, around the foam pattern submerged in a two-dimensional fluidized bed. The model was benchmarked against past fluidized bed experiments. In order to better understand the dependence of the void fraction pattern around the lost foam pattern, certain physical parameters are varied and the resultant void fraction maps are predicted with the model. Physical parameters such as the aspect ratio of length to width, the placement of the mixing jet, and different mixing jet velocities are varied to illustrate the dependence of the time-averaged void fraction on those variables.Results consistently indicate the presence of channeling around the lost foam pattern, with the extent of the channeling and void formation reliant to a greater degree upon the placement of the mixing jet, and to a lesser degree on mixing jet velocity and aspect ratio.The increase in radial position of the mixing jet from the bed centerline had the desirable effect of granting the churning benefits of a penetrating jet, while at the same time minimizing the formation of excess void fraction at the top of the pattern."

Jan 1, 2001

By Klaus Bauckhage

Phase-Doppler-anemometry (PDA)-measurements have to be taken from representative measuring positions from inside the spray cone, helping - with the support of simulated data of improved process models - to describe the multiphase flow situations within the spray cone - and accordingly to that - the heat transfer conditions for the rapid cooling and (partly) solidifying melt droplets before their impact onto the substratddeposit. Simulations and PDA-measurements thus give the base to confirm the hypothesis of the existence of a semisolid mixed-layer and it's influence on the resulting material structure during compaction. The dispersed particles in the spray cone exhibit a cooling and solidification process within a split of a second, which leads - as far as the particles solidify - to a dendritic structure with very short dendritic arm spacings. This causes within the particles extremely short distances for the following equalizing diffision processes taking place on a high temperature level (between liquidus and solidus) in the semisolid mixed-layer of the deposit and explaining the short residence times within this zone of only seconds up to a few minutes. This and the fact that the globular structure of the mushy zone (in the semisolid mixed-layer) leads to an unidirectional crystallization process over very short distances also explains the chemical and morphological ,homogeneity of the sprayed material. The dynamics of these process steps, the very special buffer function of the mixing layer during parameter variations as well as the controlled cooling process of the preform in order to avoid hot cracks influence the quality of the material. Due to the necessity of measuring and controlling the particle bound mass-, momentum- and enthalpy- fluxes to the deposit the PDA-technique has been adapted and modified in order to receive in-line and (in the future) also on-line data from the dynamics of the multiphase flow conditions within the spray chamber.

Jan 1, 1999

By Dong Liang, Honggang Zhong, Zhenxing Yin, Qijie Zhai

"2507 super duplex stainless steel (SDSS) has been widely applied in a marine environment, attributing to its excellent pitting corrosion resistance and mechanical properties which are particularly determined by the nitrogen precipitation behaviors and volume fraction of ferrite. In this paper, various cooling rates were obtained by applying four different moulds with the common gating system. By which the influence of cooling rates on nitrogen precipitation behaviors and the ferrite fraction in cast 2507 SDSS was comparatively investigated. The results showed that nitrogen porosity could easily precipitate in cast 2507 SDSS under standard atmospheric pressure. The number of nitrogen holes increased with decreasing the cooling rates, and the holes mainly distributed in three zones, i.e. the interface between the horizontal and vertical columnar grains, top vertical columnar grains and the final solidification region. Additionally, higher ferrite fraction was obtained with lower cooling rates.IntroductionDuplex stainless steels (DSS) have a dual-phase microstructure consisting of ferrite (d) and aus-tenite (?). Due to the combined advantageous properties of d and ? phase, their application rapid-ly increased in industry [1, 2]. Super duplex Stainless Steel (SDSS) is the third generation of du-plex stainless steels, of which the alloy elements Cr, Ni and N content are higher than the stand-ard 2205 DSS. Because it has high contents of alloy elements, the SDSS has better mechanical properties, and its pitting resistance equivalent number (PREN) reached a point 43. Hence SDSS has been used in petroleum chemical industry, the marine equipment and harsh corrosion environments [3]. SDSS contains ferrite stabilizing elements, such as Cr, Mo and Si, and austenite stabilizing elements like Ni, Mn and N [4]. Many researchers have studied the effects of these elements on the stabilization of d and ? phase and the ratio of the two phases. High nitrogen con-tent is another prominent feature of SDSS. Nitrogen addition to SDSS is very effective for improving its mechanical properties [5] and corrosion resistance [6], such as pitting resistance in NOx environment. To increase the nitrogen content in steels, a lot of work had been done. N. Nakamura and S. Takaki [7] examined the behavior of nitrogen absorption in Fe-23Cr alloy powder by sintering in nitrogen gas atmosphere, they found nitrogen content easily up to 1.0 wt. %. Using devised NH3 gas injection system, W. Park et al. [8] successfully produced austenitic Fe–23.5Cr alloys containing over 3 wt. % of nitrogen. Further-more, W.P. Tong et al. [9] stated that nitrogen percent was extraordinary high (about 10 wt. %) in pure iron plate. However, the above methods are difficult to be applied to large-scale industrial production."

Jan 1, 2012