Search Documents

By J. R. Donald

Surface and interfacial phenomena play a significant role in refractory performance. For example, the wettability of the refractory material with slag, matte, and metal influences infiltration and interfacial reactions. Yet, very little fundamental information regarding the surface properties of refractory materials and slag is available. Thus, in the present work, the sessile drop technique incorporating a high temperature furnace equipped with X-ray fluorescope was employed to investigate the surface and interfacial phenomena of fayalite-type slags on solid alumina at 1200?C. The iron to silica (Fe/SiO,) ratios employed were 1.4 and 2.0, and the oxygen potentials used were log p02 =-11 and log p02=-9 atmospheres. The contact angle between the fayalite-type slags and the alumina were determined to be relatively low, at about 16.9 to 19.6 degrees under the experimental conditions. The surface tension of fayalite slag (Fe/SiO2=1.4) at an oxygen potential of log -11 was 0.298, which agreed with the work of previous researchers. The surface tension of the fayalite was observed to increase with time. The spinel FeAl2O4. was determined to be the product of the interfacial reaction, and 8.8 to 15.8 mass percent alumina was dissolved into the slag after 40 minutes.

Jan 1, 1996

By Ting Liu, Qian Li, Peng Deng

The wastewater containing Hg2+ and Pb2+ does great harm to the environment and human bodies. Traditional wastewater treatment cannot fundamentally put a stop to heavy metals pollution for producing secondary pollution. In this paper, Hg2+ and Pb2+ in wastewater were removed and recovered by sulfide precipitation- flotation. Sodium sulfide was used as precipitant and butyl ammonium aerofloat was used as collector. Results indicated that Hg2+ and Pb2+ could be reduce to less than 0.03mg/L and 0.16mg/L respectively by both coprecipitation- floatation and fractional precipitation- floatation. In these two methods, fractional precipitation flotation could not only remove Hg2+ and Pb2+ from wastewater, but also could recover mercury and lead effectively. The infrared spectrograms showed that the adsorption between butyl ammonium aerofloat and mercury precipitate or lead precipitate is chemisorption.

Jan 1, 2015

By Liya Bochkareva, David Hui, Sergey Eremeev, Maksim Kireitseu, Igor Nedavniy

The principal goal of the present paper is to demonstrate an application of modern software engineering tools for modeling virtual reality and molecular dynamics of novel nanocomposites. The main technical components of presented system are I) software and nanoengineering tools for modeling of virtual reality, molecular dynamic and 30 video images of novel diamcindscontaining nanocomposites and 2) Problem tracking system to be used during modeling of virtual reality. A computational scheme and software, which utilizes neural networks and/or Microsoft. Net technique was developed to predict properties of nano-structured materials and optimization and control of nano-devices. Developed software and IT nanoengineering tools can be used by both industrial and private single users. For commercial companies proposed technology may provide better cost-effective alternative to the existing solutions for nanoengineering and modeling their virtual realit. For private users (students, professors, and engineers) proposed technology and IT tools can provide simple and cost-effective solution for nanoengineering while studying, exploring virtual reality and modeling novel nanostructures and its properties leading to an innovation or a discovery. Because of using novel software and methodologies, users can easily operate proposed technologies by available computers and operating systems (Pentium III or IV). In addition, users can upgrade it by their own self-written models, if necessary. The proposed technologies could replace or be used along with technologies for modeling such as 30 max studio and others.

Jan 1, 2004

By Xiaodi Huang, Matthew Andriese, Zheng Zhang, Jiann-Yang Hwang, Zhiwei Peng

"A simplified finite-difference time-domain (FDTD) algorithm for modeling microwave propagation in magnetic dielectric materials was developed and employed to study the microwave dissipation in magnetite. Heat transfer during microwave heating of magnetite was subsequently investigated by solving heat transfer differential equation using explicit finite-difference (EFD) method. It is observed that temperature of magnetite surface increases rapidly in the first minute due to the rapid strength decays in both electric and magnetic fields within a short distance along the path of microwave dissipation. A temperature peak, initially formed at the surface of the sample slab, migrates inward as heating time extends and microwave power increases.IntroductionAs one of primary materials in iron and steel industry, magnetite exhibits excellent microwave absorption capability, which leads to great energy conservation in microwave assisted steelmaking [1,2]. The fast temperature increase in microwave heating of magnetite can be attributed to both dielectric and magnetic losses [2]. Although much experimental work has confirmed this observation, detailed computational studies for modeling of microwave field dissipation in magnetite at commonly used frequencies, such as 915 MHz, has not been well addressed [1,3].Finite-difference time-domain (FDTD) method is widely used in computational electrodynamics modeling to simulate the dynamics of electromagnetic wave scattering from various media [4,5]. This approach requires modeling algorithm to be formulated with integration of specific characteristics of each medium. An extensive literature survey indicates that current formulations are only suitable for modeling electromagnetic waves propagating in normal dielectric lossy materials [5,6]. Since magnetite is a magnetic dielectric material in which both dielectric and magnetic properties contribute to the heating process under microwave irradiation, a specific algorithm should be developed for the simulation."

Jan 1, 2012

By Christiana Mystrioti

Greece is the only EU country with extensive nickel laterite deposits. Since the 1960s, the Greek laterites are treated for ferronickel production via a pyrometallurgical route, which involves pre-reduction of the ore in rotary kilns and reduction smelting in electric arc furnaces. Due to the rising cost of energy and the decreasing grade of mined laterites, the pyrometallurgical treatment is economically marginal. For this reason, alternative treatment processes are currently under investigation. Potential applicability of hydrometallurgical treatment, using either H2SO4 or HCl, under atmospheric pressure conditions, for Ni and Co extraction from two low grade laterite ores, was examined in the present work. The two samples were selected to represent the different mineralogical composition of the saprolitic and limonitic ore deposits of the Greek laterites. The investigated parameters were temperature (65–90 °C), acid concentration (1–4 N) and solid to liquid ratio (10–30% w/v). The results indicated that HCl was more efficient than H2SO4 for the treatment of the saprolitic ore; Ni and Co extractions were very high for both elements, up to 98% and 96% respectively, while H2SO4 could leach efficiently Ni, up to 100%, but extracted only 34% of Co. Hydrochloric acid was also more efficient for the treatment of the limonitic ore, with Ni and Co extractions up to 98.3% and 87.6% respectively. With H2SO4 the maximum extractions were 71.3% for Ni and 52.1% for Co.

By Jim Hardy, Tim McKnight

"The thermal mass flow controller, or MFC, has become an instrument of choice for the monitoring and controlling of process gas flow throughout the materials processing industry. In the semiconductor industry, these MFCs are used on over 70% of the processing tools. Reliability and accuracy are major concerns for the users of the MFCs. Calibration and characterization technologies for the development and implementation of mass flow devices are described. Sources of inaccuracy in process gas handling are described, and a model to correct for these inaccuracies is outlined. A gravimetric calibrator is described that allows flow sensors to be calibrated in corrosive, reactive gases to an accuracy of 0.3% of reading, at least an order of magnitude better than previously possible. All described capabilities are implemented in a Department of Energy User Facility which is available to industry and universities to test and develop gas flow sensors and controllers and evaluate their performance related to environmental effects, reliability, reproducibility, and accuracy.IntroductionMaterials processing is at the heart of semiconductor manufacturing. To make today's advanced integrated circuits, silicon wafers are subjected to over 200 process steps. Most of these steps involve processes such as etching, implanting, diffusion, annealing, deposition, and lithography (resist deposition and hardening). Often one or more process gases are used to complete the process step. To achieve the quality and performance required in the micro devices, accurate measurement and control of these gases is essential. The Oak Ridge National Laboratory (ORNL), in conjunction with the semiconductor industry, has been working to improve process gas measurement and control accuracy and reliability. Standardized test methods have been developed to characterize and benchmark the performance of mass flow controllers (MFCs), the method of choice for monitoring and controlling gas delivery. Testbeds have been designed and fabricated to produce repeatable and accurate data using these standards. Baseline testing was performed along with development of a unique mass flow instrument, the gravimetric calibrator."

Jan 1, 1997

By Scott R. Giese, Lucas Dix

"Recently, there is a growing trend in the aluminum foundry industry to develop· improved melting and casting processes to produce lightweight, high-strength, and thin-wall castings for the aerospace and transportation industry. One casting method that has demonstrated industrial potential for producing clean, thinwall castings is vacuum-assisted, counter gravity casting. This process has the benefit of expeditiously and quiescently filling the casting cavity with a dramatic reduction of furnace related and reoxidation inclusions. Additionally, lower casting temperatures can be utilized because the application of vacuum during filling overcomes the resistive internal cavity pressure resulting in a finer, as-cast microstructure. The paper explores and discusses the processing and design conditions in improving the mechanical properties of A206 casting alloy using the vacuum assisted, counter gravity casting process.IntroductionThe process of metal casting has been, over the centuries, the chief production technique for components used in everyday life. However, the casting process has certain inherent problems that can adversely effect the properties of a finished product. These problems are directly attributable to the gravity pouring technique used to transfer molten metal to the mold and to fill the mold cavity.A recent study for the American Metalcasting Consortium demonstrated reoxidation products created during the casting process are five times more likely to cause product rejects than entrapped molding aggregates, melt slag, or furnace lining materials1. Formation of nonmetallic and intennetallic compounds are more prevalent in aluminum and titanium alloys because of their reactiveness to furnace lining materials and their high affinity for oxygen. The incorporation of undesirable compounds can be attributed to four areas of the casting operation. The sources are charge materials, melting technique, pouring methodology, and casting cavity filling. Aluminum foundry men have addressed the first three areas by selecting high quality melt stock, non-stirring melting equipment, and the use of porous ceramic filters. Unfortunately, little consideration is given to the last, but yet tl.1e most important part of the casting operation, the actual fill mg of the casting cavity.The generation of inclusion defects during the casting process can be described by two methods. As the liquid metal flows in the gating network and casting cavity, abrupt changes in flow d1rect10n cause the metal to become agitated. This mechanism liquid metal splashing, is generated by instability of the advancing liquid metal interface from turbulence effects as schematically illustrated in figure 1a2 . The surface oxide film bursts under high velocity conditions, folds over, and becomes dispersed and incorporated in the bulk liquid. Additionally, fragmented liquid droplets ejected from the disturbed interface oxidize and become dispersed in the metal stream."

Jan 1, 2000

By T. M. Dreher

The difficulties associated with the operation of a classical rhodium refining process have prompted many attempts to develop a viable solvent extraction flowsheet for rhodium. Recent investigations at McGill University have involved the activation of rhodium prior to its solvent extraction. The role of activation is to convert the aquochloro complexes of rhodium to a form extractable by conventional solvent extraction reagents. In the novel separation scheme identified, chloro complexes of rhodium are converted to bromo complexes, which undergo aquation to a lesser extent, making them more easily extracted. Rhodium is then extracted using Kelex 100, and stripping is achieved by use of a concentrated chloride based solution. Separation of rhodium from iridium is achieved by either prior reduction of Ir(IV) to Ir(III), as the latter is not extracted, or via co-extraction and differential stripping. A conceptual flowsheet for the refining of rhodium using this method is proposed.

Jan 1, 1998

By William Petrul

Image analysis studies were performed on mill products from laboratory flotation tests of the Zn-Pb ore from the Faro deposit in Yukon, Canada, to determine mineral liberations at specific grinds and to predict recoveries at optimum flotation conditions. The minimum and optimum grinds for liberating sphalerite and galena were predicted from size analysis data for the minerals in large ore pieces, and determined by image analysis studies of the mill products. The determined optimum grinds are about 2 Tyler mesh sizes larger than predicted because sane of the fine grained sphalerite and galena occurs in interstices between coarser grained pyrite and is liberated when the pyrite grains are broken apart. Materials balance calculations were performed on the analyzed values for the liberated and unliberated sphalerite and galenaa to determine their distributions in the mill products. The laboratory flotation tests recovered 74% of the sphalerite and 83% of the galena in Zn and Pb concentrates respectively. The mineral evaluation study indicates that the optimum recovery for sphalerite and galena are 85 and 83% respectively. The company is currently recovering 80% 'of the sphalerite and 82% of the galena.

Jan 1, 1989

By Norimasa Yamasaki, Masao Kurosaki

"The effects of plating conditions on the crystal orientation of electrodeposited zinc were investigated by varying elecyrolyte flow rate and current density. Precipitation of the Zn (00 • 2) basal plane is promoted at lower current density and higher flow velocity. Effect of the flow velocity on the mass transport was evaluated based on the polarization measurement in which Cu was used as the tracer. As a result, it has been clarified that the crystal orientation of electrodeposited zinc can be uniquely arranged by the overvoltage (iU0.5) that can be simply calculated by considering -the current density and boundary layer thickness. At the same time, the electrode potential during electrodeposition that can be calculated by using a model based on the competitive reactions of hydrogen reduction 'and zinc reduction exhibits an extremely good correlation with the crystal orientation of electrodeposited zinc.Introduction Electrogalvanized steel sheet has better surface properties than hot-dip galvanized steel sheet, and is used in home electric appliance and automobile applications. Factors such as crystal morphology, crystal orientation and surface roughness have a large influence on its appliance, formability and corrosion resistance [1-3].Electrolysis, condition, bath composition and alloying elements are reported as factors that affect the crystal orientation of the electrogalvanized coating. Factors that can be controlled on time in the production site are electrolysis condition that-is current density and plating solution flow velocity.Some studies[4-6] report that the crystal- orientation of the Zn(00 • 2) plane is increased by promoting, the mass transfer of zinc ions in the plating solution or decreasing the concentration overvoltage, but did not investigate in detail the plating solution flow conditions in the plating cell nor quantitatively determine the effects of both current density and plating solution flow conditions on the crystal orientation of ' electrodeposited zinc."

Jan 1, 2000

By Xiao Yang

Calcium oxide is one of the major fluxing agents used for steel refining. Because unreacted CaO remains in slag in most cases, discharged slag is difficult to be recycled smoothly. With the growth of environmental concerns, improving utilization efficiency of CaO is required to reduce the amount of discharged slag and energy consumption. The authors have reported a resource and energy-saving process by using multi-phase flux for dephosphorization. Reaction behavior of phosphorus in multi-phase CaO–FeOX–SiO2–P2O5 flux system was investigated. Formation mechanism of P2O5-rich phases was clarified at the interface between solid CaO or 2CaO, SiO2 and molten CaO–FeOx–SiO2–P2O5 slag. Phase relationship and thermodynamic properties of 2CaO, SiO2-3CaO, P2O5 solid solution were observed to confirm the condensation of P2O5 in solid phase. Based on these results, reduction of CaO consumption, discharged slag curtailment, and energy-saving effects in the novel refining process by using multi-phase flux were discussed.

By T. T. Lin, N. H. Madsen, K. Groom, B. A. Chin

"The objective of this research is to investigate the feasibility of using infrared sensors to monitor the welding process. Data were gathered using an infrared camera which was trained on the molten metal pool during the welding operation. Several types of process perturbations which result in weld defects were then intentionally induced and the resulting thermal images monitored. Gas tungsten arc using AC and DC currents and gas metal arc welding processes were investigated using steel, aluminum and stainless steel plate materials. The thermal images obtained in the three materials and different welding processes revealed nearly identical patterns for the same induced process perturbation. Based upon these results, infrared thermography is a method which may be very applicable to automation of the welding process.IntroductionAutomatic welding is commonplace in industry today. However, most, if not all, involves preprogramming for performance of a repetitive task. These systems are incapable of correcting for perturbations which arise during the welding process. Control of the welding process requires the identification and monitoring of perturbations in a wide variety of parameters. The varied nature of these parameters and the large number of variables involved have thwarted previous attempts at closed loop control of the welding process. The sensor(s) employed by a control system need to meet rather strenuous requirements. First and foremost of these is that such a sensor must be able to identify and discriminate between perturbations that might affect the quality of the weld, including such geometrical perturbations as a change of direction in the seam between the parts being welded, gaps in the seam or a misalignment of the parts being welded. The sensor should also be able to locate and identify contaminants and impurities in the weld puddle and ahead of it while monitoring the extent of the heat-affected zone and the cooling rate of the metal. The sensor(s) should, additionally, be able to perform these tasks in a time frame that is consistent with automatic control of the welding process. This paper presents results that could aid in the assembly of such a controlled welding system."

Jan 1, 1986

By Animesh Jha

The carbothermic reduction of chalcopyrite has been studied in the temperature range 1073 to 1273K in presence of lime. The role of lime during the reduction process is explained and the phase equilibria leading to the metallisation of copper and iron are discussed. The effect of coal and carbon monoxide on the reduction process have been studied and the rate governing steps are identified. This investigation also cites examples of possible mechanisms of physical separation of metallic Cu from iron during the reduction process.

Jan 1, 1992

By Malti Goel

"Technology advancements in fossil fuel based energy generation and consumption are currently being aimed at minimization of CO2 emissions. To attain energy security, India must accelerate the pace of economic development, while achieving reduction in CO2 emissions per unit of energy consumed. It would need access to advanced coal utilization technologies to be demonstrated on indigenous coal characteristics. Of specific importance would be: improvement in coal quality, increasing energy efficiency and suitability of other CO2 sequestration technologies for reducing CO2 footprints. There is need to address related risks and financial burden through adoption of policies and regulations including the issue of open access in energy research. In this paper, seven important areas of strategic plan that need to be pursued for managing CO2 emissions in steel energy sector in India are discussed.IntroductionWorld is facing a crisis of climate change, which follows in the footsteps of global energy and environment crises. Accumulation of carbon dioxide from the generation and utilization of energy is leading to greenhouse warming and climate change. The global warming is causing the boundary between four seasons to be fuzzy and resulting in more spiky weather. Significance of its impact on environment is also determining the technology development needs in various sectors of economy for taking remedial measures.To respond to climate change concerns, the steel industry is undergoing a transition. It is at the threshold of a rapid change in technology as it targets innovation to achieve 50% reduction of CO2 emissions per ton of steel produced. Fossil fuel use is the main contributor of increasing concentration of carbon dioxide in the atmosphere. The control of air pollution and CO2 capture are thus relevant for a coal based industry, whether thermal power plant or a demand side energy intensive industry. World steel production has shown phenomenal increase in first eight years of 21st century increasing from 780 Mt in 2000 to 1343 Mt in 2008 [1]. It was merely 28 Mt in 1900. The global CO2 emissions from steel industry are also increasing and became 2550 Mt (3-4% of total GHG). Indian industry contribution was 161 Mt (15% of direct emissions from industry). It is likely to grow further to keep pace with the accelerated economic growth of 8-9% per annum."

Jan 1, 2010

By Wenbo Luo, Kang Liu, Jilai Xue

"Coal fly-ash(CFA) from thermal power plants is rich in Al2O3, which has great potential as an alternative resource for alumina production. In this work, Alz03 contained in the coal fly-ash was extracted using an acid sintering-leaching process. This process was enhanced by aid of power ultrasound during the leaching. The recovery rate of Al2O3 was increased with ultrasound, compared with the similar process without ultrasound under the identical operation conditions. Leaching temperature can be lowered by about 10-l5°C and the processing time reduced by about 50%. The process kinetics were investigated in details for a better understanding of the fundamentals on the effects of power ultrasound. The obtained results demonstrate the potential application in reducing processing energy and increasing production rate.Introduction Coal fly ash is a typical solid waste generated from coal combustion in thermal power station. Vast amount of CF A accumulation lead to serious environmental problems such as air and water pollution, cropland occupation, radioactive contamination, etc. However, CFA is rich in Al2O3 and SiO2 content, so that it has a potential use as recourses for alumina and silica production [1]. Aluminum industry, especially in China, has made a rapid expansion in recent years accompanying with a large amount of bauxite consumption, resulting a urgent demand to develop secondary alumina resources like CF A to maintain a sustainable development of aluminum industry that faces grim challenge [2].Acid leaching is an efficient technology to use in alumina extraction from CF A. Since the particle of CF A is not naturally existed mineral but was formed in molten state at high temperature, the internal Al-O-Si bonds are so strong to separate alumina from the ash particle. Because of this reason, the direct acid leaching [3-6] operated at ambient temperature has low extraction efficiency, approximate 30% to 40%, which is attributed to self inhibition effect from CaS04 generated by reaction between CaO and H2S04 [7-8]. High pressure leaching can efficiently decompose mullite to release A12O 3 content in the fly ash particles, but this requires autoclave material having strong acid corrosion resistance, high temperature (100°C-300°C) and pressure (1.0MPa-2.SMPa) resistance while its operating security is low and its acid consumption is large [9]. Concentrated acid boil process is conducted at near acid boiling point (200 °C - 300 °C) in 4 mouth flask wrapped by electric heating jacket with high mass ratio of acid and ash to achieve high Al203 recovery rate from CFA. Its disadvantages are similar to the high pressure leaching technology except no-pressure, and also the operating solution at nearly boiling point acid may easily spill and splash with additional acid loss and potential safety hazard [10]."

Jan 1, 2014

By Qingyu Deng, Shiwei Ma, Guibao Qiu, Hua Wang

"The flow behavior of the blast furnace slag bearing titanium, like viscosity, play an importance role during the iron-making process with the vanadium-titanium magnetite, which is a very special minerals in Panzhihua, China. The dependency of the viscosity on the chemical composition like TiO2, Al2O3, MgO, binary basicity (CaO/SiO2), temperature, reaction time were studied. The experiments showed that the viscosity decreased with the increase of TiO2, MgO content and binary basicity, and it increased with the increase of Al2O3 content and temperature. The viscosity showed a slight decrease within 60mins’ reaction with graphite crucible, however, it increased rapidly afterwards with the formation of Ti(C, N).IntroductionThe ordinary iron ore has been an essential part of raw materials for vanadium-titanium magnetite smelting in Panzhihua to avoid a series of problems, such as slag thickening, adhesive bond of slag and hot metal, etc. The ratio of vanadium-titanium magnetite has been decreased gradually since 1970s, and has down to about 65% now. However, with the substantial appreciation of price of imported ordinary iron ore, Panzhihua Iron and Steel Group aims to increase the ratio of vanadium-titanium magnetite and decrease the dependence on ordinary iron ore in order to lower the cost of smelting process."

Jan 1, 2012

This paper describes developments in ferro-nickel furnace technology, specifically improvements to cooling methods, furnace controls, and high voltage furnace operating regime. The evolution of these technologies is briefly presented, as context for describing the current state of the art that has enabled ferro-nickel furnace operation at over 75 MW and specific energy consumption of less than 400 kWh/t dry ore. Examples from existing operations are used to illustrate present best practices, and potential future trends are discussed: The paper begins with an overview of the fundamental aspects of pyrometallurgical treatment of lateritic ores that drive ferro-nickel furnace design. Furnace wall cooling methods are related to the requirements resulting from specific furnace process conditions, including slag and metal compositions, as well as arc and bath power. The benefits of high productivity and low specific energy consumption resulting from high voltage (shielded-arc) operating practice are discussed, along with the furnace controls and electrical power train that enable such operation even with captive power generation. This paper is an update of that which the authors prepared for the Infacon X ferro-alloys conference.

Jan 1, 2004

By Yoichi Takeda

Copper solubility in Si02-CaO-FeOx slag equilibrated with copper matte in 10% S02 atmosphere at 1573K was estimated. Essential parameters are activity coefficients of copper oxide and sulfide, oxygen and sulfur potentials and activity of copper in the slag-matte system. A large number of experiments provide proper parameters to calculate copper solubility in slag. A classical thermodynamic model postulating CUOO.5 and CuSo.; molecules assists in estimating copper solubility in slag. Additions of Si02 and CaO reduce copper solubility almost in any condition. Copper loss, that is function copper solubility and slag volume, in the silica saturated Si02-FeOx binary slag is minimally equilibrated with less than 66% copper matte while copper loss in the 50% FeOx-SiOrCaO ternary slag saturated with 2CaOSi02 is minimally equilibrated with over 66% copper matte. This slag composition has potential for continuous copper converting, direct copper production or high-grade matte production.

Jan 1, 2003

By M. Potesser

In the primary and secondary copper industry the anode furnace is the most important process step in the refining procedure to reach an enhancement in value and quality of the copper by a selective oxidation and reduction. By combining the advantages of the conventional tilting hearth anode furnace and the benefits of the drum type anode furnace a new aggregate was developed and patented. The cross-section of the furnace is elliptical and the whole unit is tiltable. During the melting period, the contact surface between the burners and the bath or the scarp is enlarged - an increased energy input is the consequence. For the refining period the furnace is rotated, whereby a high bath level is guaranteed. Due to the longer residence time of the gas in the copper melt, not only the gas consumption is reduced but also the efficiency/quality of the refining process is improved. This investigation shows a metallurgical comparison between the new anode furnace concept with the elliptical profile/cross section and the conventional, tiltable hearth anode furnace as well as the drum type anode furnace. The CFD modeling of the currents in these different furnaces delivered helpful data to compare the geometry of the different furnaces. The investigation covered the refining of blister copper from primary metallurgy, from secondary metallurgy as well as from a mixture of both copper melts. The paper underlines the possibilities for a reduction of the tap-to-tap time and for an increase in production capacity, which can be achieved by applying the new furnace concept in comparison to the conventional furnaces.

Jan 1, 2006

By N. V. Gorelikova

A new type of zirconium mineralization has been recognized in the Devonian volcanic rocks from an orogenic depression in the Central Kazakhstan. The most characteristic features of this deposit are the fine-grained nature of the zirconium mineralization, an unusual texture of the zirconium ores, and a close association of zirconium with phosphorus in the ores. Zircon grains form fine globular aggregates with the features of hexagonal crystal habit. In addition to crystalline zircon, the ores contain metacolloidal zircon, similar to hydrozircon. The morphological and textural features of the zirconium ores suggest that the deposition of ore deposits took place at a low temperature from colloidal solutions. It is believed that this deposit should be considered to be a new type of zirconium mineralization that is related to low-temperature hydrothermal processes.

Jan 1, 1995