Search Documents

By Guorui Feng, Min Zhang, Yi Luo, Jian Yang, Yujiang Zhang, Junwen Bai

"Safe mining of coal seam sandwiched between abandoned upper and lower room-and-pillared mines (ULPM) ·is increasingly becoming the focus of attention in recent years, which is closely related to the damage intensity of the upper and lower interburdens. The #7 seam with ULPM in Baijiazhuang coal mine was selected for this research. According to the mining and geological conditions, the vertical stress and plastic zone distributions were determined first by numerical simulation. Then, a theoretical model based on the elasti-plasticity theory was developed. The stress distribution and failure zone created in the interburden by mining the upper and lower seams were determined. Finally the feasibility of mining #7 seam between the abandoned upper and a lower seam was evaluated. The results show that: (1) the distributions of abutment pressure and plastic zone coincide, both of which can be used to evaluate the failure zone in ULPM. The failure zone penetrates the whole upper interburden, while only parts of the lower interburden fail. (2) the theoretical failure zone coincides with the maximum distribution zone of abutment pressure and plastic zone obtained by numerical simulation: the failure zone height in the lower interburden is less than its thickness, while that in the upper interburden is larger than its thickness. (3) the #7 seam is located in the failure zone created by the upper seam room-and-pillar mining, which leads to well-development fractures and blocky fragments in the roof, thereby it is unstabled. (4) when mining the #7 seam in the interburden, the key is to control the roof strata and proper support measures should be taken timely to ensure safe mining.INTRODUCTIONMany coal mines in China mine the thick, superior and easily mineable resources preferentially, while the thin, inferior and difficult-to-mine resources were abandoned (Chappells and Trentrnann, 2015; Zhenfu, 2012; Xu, et al., 2015; Guorui, 2009). As the results of deficient geological data and shortage of investment capital, the residual coal resources distributes in many mining areas in China.In recent years, many residual coal seams sandwiched between the abandoned upper and lower room-and-pillar mines (ULPM) were explored in Shanxi Province, especially in the mining area of Datang, Xishan and Luan (Figure.1). The reserves of residual coal seams in ULPM are considerable, increasingly becomes the focus of attention among scholars and engineers."

Jan 1, 2016

By Klaus-Dieter Beck

RAG American Coal Holding, Inc. affiliates operate two longwall mines in the Pittsburg seam in Pennsylvania, the Cumberland mine and the Emerald mine. A unique situation in longwall operation occurred at these mines as the mining activities reached the property boundary between the two mines. The retreat direction in the longwall panel in Cumberland mine is West-to-East while in Emerald mine, it is East-to-West. This unique condition required an adequate design for barrier pillar between the two mines to minimizing the mutual effects of longwall retreat when both longwall faces met and an adequate roof control plan for gateroads. Field studies that involved mainly roof-to-floor convergence monitoring were conducted to assess the effectiveness of the employed barrier pillar in isolating the mutual effect of longwall retreat. Three-dimensional finite element numerical modeling was used to evaluate the gateroad roof and pillar stability. The modeling was conducted such that it duplicated the actual mining process as realistically as possible. The modeling results predicted that the employed barrier pillar and the roof control plan would ensure stable gateroad systems in both mines during and after the two longwall faces met. The prediction was confirmed because mining operations in the two longwall panels were completed without any noticeable ground control problems.

Jan 1, 2004

By Daniel W. H. Su

Surface subsidence induced by multiple-panel coal extraction was calculated with finite element stress analysis. The use of nonlinear material behavior and GAP elements, which provide a realistic representation of shearing along existing planes of weakness, allows the finite element program to accurately reproduce observed subsidence profiles. A reduction factor of 1/6 is applied to the measured rock strength and modulus for use in the finite element model. The models satisfactorily predict a significant change in maximum subsidence and subsidence profile associated with an increase from subcritical to near critical panel width. Modeled shearing along planes of weakness is in good agreement with available time domain reflectometry field observations and is demon¬strated to have a very profound effect on the maximum subsidence and the shape of the subsidence profile. When both material nonlinearity and planes of weakness are incorporated, the finite element model appears to possess great potential for accurately predicting surface subsidence and subsurface strata deformation in environments where little subsidence information is available.

Jan 1, 1990

By Bruce K. Hebblewhite

Underground pillar extraction continues to be practiced in Australia in various forms, in spite of the dominance of the longwall method, which accounts for over 90% of underground production. Australia has been a leader in various forms of pillar extraction, particularly since mechanisation was introduced to the industry during the middle of the 20th century. Historical developments have included a range of thick seam mining pillar extraction methods; the widely adopted Wongawilli method; early adoption of the use of mechanized breaker line supports; and a number of more recent partial extraction systems including what is known as rib stripping. Current pillar extraction practice varies from total extraction panels to various forms of partial extraction, driven by either surface subsidence constraints or by underground conditions. This paper reviews a number of different pillar extraction methods and mining layouts, and also highlighting a number of fundamental geotechnical principles which have been found to be critical for safe pillar extraction ? often through lessons learned the hard way, as a result of back analysis of different accident scenarios. These principles include the all-important understanding of the location of the goaf (gob) edge at any point in the operation, and the management of that goaf edge; the impact of geological structures on local and regional stability; the critical importance of extraction lifting sequences; the role of stooks (remnant pillars); and a number of other factors. The paper will also briefly reference the educational and training practices adopted in Australia aimed at the continuous improvement of pillar extraction safety.

Jan 1, 2011

By Christopher Mark

The past decade has provided a wealth of practical experience with longwall pillar design. Design formulas developed specifically for longwalls have proven their value in numerous applications. Analytic methods, including numerical models, have a1 so made important contributions. These advances have been based on basic research into abutment loads, coal pillar mechanics, and the interaction between pillar performance and entry stability. The goal of this paper is to review the state of the art in longwall pillar design from the standpoint of the practitioner. Actual case histories are presented to illustrate the current capabilities and limitations of pillar design methods. The paper also discusses the advances that can be expected in the future.

Jan 1, 1990

By André Vervoort

To learn more about the fundamental roof behaviour in South African coal mines, accurate underground measurements of roof deflection were conducted in bord and pillar panels during development and pillar extraction. To conduct these measurements a survey levelling technique was adapted. The overall system reading accuracy was established as being within 0,4 mm on a 15 m sighting distance. The underground sites were modelled and, for a roadway development, similar symmetrical curvatures were calculated by a linear elastic model, as were measured underground. In a pillar extraction panel, a significant amount of bed separation was measured and the roof underwent an a-symmetric movement due to the close presence of the mined out area at one side of the roadway.

Jan 1, 1992

By Michael Kelly

Current research in longwall mining in CSIRO Exploration & Mining is focused within five major projects and several minor projects. The major projects are: 1 3D Aspects of Longwall Geomechanics. This was reported to the conference last year and a final report will be available by mid-2001. 2 Mine Gas Control. This just completed project centred on Dartbrook Colliery which has a longwall gas make of more than 8 cubic metres per second. 3 Rapid Roadway Development This includes the construction of an autonomous conveying and bolting module (ACBM) that sits between the miner and haulage system. 4 Top Coal Caving In conjunction with the YanKuang group in China, CSIRO and the University of NSW are conducting a prefeasibility study of the Top Coal Caving method in Australian conditions. 5 Longwall Automation. In partnership with the Cooperative Research Centre for Mining Technology and Equipment (CMTE), the CSIRO has conducted a scoping study on this issue and will commence an initial three-year demonstration project in July this year. This paper describes these protects in more detail with particular focus on the last three in the above list.

Jan 1, 2001

By Anil Mahyera

Under contract to the Bureau of Mines, a roofbolting machine has been developed which will: control torque on the bolthead to within 4 percent of a set point, control thrust to a low level (150 lbf), and implement a tightening method to minimize variability due to bolt tension decay of a group of bolts caused by differing anchor creep rates. This bolter was used to determine bolthead and thread friction factors, and to determine the effect of adding a hardened washer to the bolt assembly on the uniformity of bolt tension in the laboratory and field. Recommendations for torquing speed, bolt lubrication, use of hardened washers, and thrust level on the bolthead are made. The relationship of this system to Improved roof control is discussed, along with additional work that remains to be performed. Patent Notice Patents are pending which protect the hardware and methods of controlling tension decay as discussed in this paper.

Jan 1, 1981

By B. T. Wells

This work concerns the stress fields encountered around mining tunnels. A critical review is undertaken of the various analytical assessments of the support requirements for mining tunnels. Comments are made regarding degree and type of support together with method and timing of installation. The results have been used to indicate the type of support required in different mining and geological conditions.

Jan 1, 1981

By Robert C. Garson

The Mine Roof Simulator at the DOE'S Mining Equipment Test Facility is described. Its use in the research and development on the behavior and response of longwall roof supports to simulated mine environment is investigated. Advanced technology analysis methods such as finite element modeling, strain gage instrumentation, and photoelastic techniques are investigated for application in roof support design two case studies are presented of test data and results.

Jan 1, 1982

By Chris Haycocks

The relevant literature concerning ground control, mine planning and reserve conservation in multi- seam mining is reviewed. Factors affecting interaction, interaction mechanisms, and design guidelines are presented in detail. The impact of multi-seam mining on future mining, measures for ameliorating negative interaction effects, and future research needs are also discussed.

Jan 1, 1990

By Murali Gadde

U.S. coal mines? primary roof supports typically consist of passive resin bolts; however, the use of active bolt systems is increasing. Despite this widespread use, a comparative performance evaluation of these bolt systems has not been done under similar geologic conditions. The performances of three commonly used primary bolt systems were investigated: fully grouted passive rebar, fully grouted tension rebar (using two speed setting resin), and resin-assisted rebar with mechanical anchors. In order to investigate the performance of these bolts, strain gauged bolts of all three types were installed at three different coal mines as part of a larger research project funded by the National Institute for Occupational Safety and Health (NIOSH). This paper addresses the initial installation bolt loads measured at these mines. Analysis of the data showed much lower installed loads on active bolts than is traditionally assumed. It appears that the active load on bolts bleeds off relatively quickly under geologic and operational conditions similar to those at the studied mines. The data also showed that within a short time span after installation, the measured loads on active and passive bolts did not differ significantly. This paper compares the results from over 20 bolts of each bolt type that were all 1.8-m (6-ft) -long, 20-mm (0.804-in) nominal diameter Grade 75 rebar and discusses the relevance and shortcomings of the data and bolt performance.

Jan 1, 2011

By Andre Vervoort

The roof in coal room and pillar panels is normally stratified and can be thought of as beams or plates supported by the pillar sides in the roadways and by pillar corners in the intersections Underground measurements showed the effect of the face advance on the additional total movement of the roof skin and on the relative movement between various layers in the roof. The latter consists of the opening of bedding planes and of the lateral sliding of layers over one another. Both phenomena increase locally the axial load along full column anchors. Four models have been used to come to a better understanding of the roof behavior: a beam either clamped above the pillar side or laying on the pillar sides and a three-dimensional boundary clement model with and without bedding planes. The shape ref the curvature of the roof deflection is host approached by a clamped beam: the other models overestimate the movement at the sides. The largest roof deflection for a given Young's modulus is estimated by the model incorporating bedding planes. This model estimates that the bed separation occurs close to the face (within the first meter) and within 0.2 m of the sidewalk. In some simulations, openings are even recorded just ahead of the face. Further underground measurements should focus on these findings, as the effectiveness of the support is directly related to the amount of bed separation and sliding, which have occurred prior to the support installation and which still cart occur abler installation.

Jan 1, 2000

By I. Geldmacher

In-Seam Seismic (ISS) methods have been used extensively worldwide for the past 10 years to assist mine planning, espe¬cially longwall mining in coal seams. The technique is only starting to gain wide acceptance in North America where it is being applied in a much wider variety of applications than was initially considered. Surveys elsewhere have concentrated on the detection of faults (structures) in coal mines prior to longwall mining. The majority of surveys in North America has been the location of abandoned workings which were not adequately surveyed prior to closure. Modeling data based upon the lithological logs, geophysical logs and interpreted sections show whether the method will be successful prior to carrying out the survey. The surveys have been performed to locate abandoned wor¬kings from the surface and underground using both seismic reflection and transmission techniques. Data from coal seams in both Illinois and West Virginia will be presented. A second method where ISS surveys are being applied to detect old workings will be presented. The ISS tomography produces an image of the P-wave and Channel Wave velocities which is representative of the material through which the signal traveled thus identifying the location of the old workings. Data from Texas will serve as an example.

Jan 1, 1990

By K. Y. Haramy

Strong roof helps minimize roof fall problems in coal mine entries. However, the Inability of strong roof to cave readily may contribute to major ground control problems In Iongwall and retreat mining operations. The concern expressed by mine operators prompted this Bureau of Mines study to analyze the effects of strong roof members on ground stability around Iongwall openings. The problem was approached from three directions: development of a theory to analyze the strain energy conditions In the coal and surrounding strata, modeling the effects of different thicknesses and strengths of Coal and roof strata, and field Instrumentation of powered supports In two Iongwall mines. Results from the theoretical and modeling analysis confirm the accepted belief that a strong roof does, In fact, play a major role in high stress concentration problems In and around the Iongwall panel. Analysis of the effect of different roof overhang dimensions and properties on relative strain energy buildup In the coal and roof Is presented. Shield pressure data Indicate possible methods for detecting noncaving roof behind the shields. Strategies to monitor roof overhang and control dangerous conditions caused by the noncaving roof are also presented.

Jan 1, 1988

By Brian Clifford

Thoresby Colliery is in the process of recovering an old roadway that was flooded following the closure of an adjacent mine. The aim is to re-use the roadway as a gate road for a longwall retreat panel and it is therefore important to establish the condition of the existing rockbolt support during the recovery operation. Two NDT methods, ultrasonics and RMT's newly developed RF (Radio Frequency) system were used in combination to interrogate the rockbolts to determine their condition. This paper describes the condition of the rockbolt supports, the NDT methods used and the problems that had to be overcome to successfully apply the two methods.

Jan 1, 2002

By Revendra Awasthi

The application of a horizontal inclinometer and a tiltmeter to measure tilt, curvature, and deformations of shallow footings during mine subsidence is described. The measurements were taken during mining of a longwall panel in Southern Illinois and were supplemented with precision level survey data. Monitoring was conducted under a cooperative agreement between the Institute for Geotechnology at The University of Tennessee, Knoxville, the U.S. Bureau of Mines, the National Science Foundation, the Illinois Mine Subsidence Insurance Fund, and Old Ben Coal Company. Six different footings were constructed and instrumented at two sites; one above the panel centerline, and the second inside the edge of the panel in the anticipated zone of maximum tension. A brief description of the inclinometer casing and tiltplate installation is described, and the results obtained from the two instruments on a plain concrete footing compared. Observations of footing deformations and curvatures calculated from the inclinometer and tiltmeter data are also presented, and the results compared with observed structural damage.

Jan 1, 1990

By John Latilla

Following its introduction on underground collieries, the mandatory Code of Practice to Combat Rockfall Accidents (CoP) was applied to all opencast operations of lngwe Collieries (the South African division of BHP Billiton Energy Coal). The CoP includes, but is not limited to, requirements to assess hazards, manage them and monitor compliance. Information on methods to measure highwall conditions and compliance with control measures on opencast strip mines, as opposed to open pit mines, was found to be anything but freely available. However, on the Ingwe underground mines, a system of rating physical conditions in each section and how well production personnel were managing the situation, has been used with success for some time. It was decided that a similar approach would be taken, and, as with the underground rating system, the resultant rating forms should not be aimed at rock engineering specialists only but should be able to be used by production personnel as well. This paper discusses the highwall risk rating method as evolved over a couple of years and highlights that it is a flexible tool that can easily be changed to suit an individual mine's requirements. It also shows how operational aspects are being measured to determine how well the identified hazards are being managed. Allied to the method is a relatively easy, and certainly "low capex," mapping technique which allows between 500 and 1000m of highwall to be covered in a day. Features generally recorded include lithology, bench height, work still to be completed, coal losses or "toes", presence of water, dolerite intrusions, existing and potential failures, prominent joints, declared special and cautionary areas, cracks on upper benches and condition of spoil piles. Highwall mapping and photography as well as basic geological data collection, enable highwall risk and operational ratings to be determined. The same rating sheets may also be completed by production personnel, but without detailed mapping.

Jan 1, 2002

By William Gray

It has been ten years since the Mine Safety and Health Administration (MSHA) promulgated a safety standard requiring the use of Automated Temporary Roof Support (ATRS) systems in underground coal mines. The use of ATRS systems with roof bolting machines and continuous miners equipped with integral bolters has all but eliminated fatal roof fall accidents associated with manually setting temporary roof support. The last ten years have seen an evolution of the ATRS systems themselves and of MSHA's policy regarding ATRS systems. These changes are a response to operational and safety issues regarding ATRS systems often brought about by the ever-changing coal mining environment. As a result, MSHA's Technical Support personnel receive numerous inquiries from all segments of the coal mining industry on various ATRS topics. These requests for technical assistance range from an interpretation of a facet of the ATRS standard to an in-depth evaluation of a prototype ATRS system. This paper will address the aforementioned evolution of ATRS systems and will also summarize the factors MSHA Technical Support uses to evaluate these systems in the field. In addition, some of the more common misconceptions regarding the design, use, and regulatory requirements regarding ATRS systems will be covered.

Jan 1, 1998

By Roy H. Grau

The trend in underground room-and-pillar cod mining is to employ remote-control continuous mining machines to take extended cuts of 40 A or more. Roof fall safety hazards to the mine worker associated with 4ed cutting are not completely de6ned but are known to include removal of the miner operator from the protective canopy, non-compliance with approved cutting depth and CM operator positioning. This report summarizes ground control research performed by the National Institute for Occupational Safety and Health (?-JIOSH) researchers at the Pittsburgh Research Laboratory concerning extended cuts. A combination of statistical analysis and underground investigations have been conducted. Statistical analysis of extended cut use, along with roof fall accidents and fatalities data delineate the extent of the problem in U.S. coal mines. Additionally, an underground study is described where the long-term roof stability of extended cut areas are compared to standard cuts.

Jan 1, 1997