Search Documents

By Juan J. Monsalve, Nino Ripepi, Richard Bishop, Jon Baggett

"Terrestrial laser scanning (TLS) is a useful technology for rock mass characterization. A laser scanner produces a massive point cloud of a scanned area, such as an exposed rock surface in an underground tunnel, with millimeter precision. The density of the point cloud depends on several parameters from both the TLS operational conditions and the specifications of the project, such as the resolution and the quality of the laser scan, the section of the tunnel, the distance between scanning stations, and the purpose of the scans. One purpose of the scan can be to characterize the rock mass and statistically analyze the discontinuities that compose it for further discontinuous modeling. In these instances, additional data processing and a detailed analysis should be performed on the point cloud to extract the parameters to define a discrete fracture network (DFN) for each discontinuity set. I-Site Studio is a point cloud processing software that allows users to edit and process laser scans. This software contains a set of geotechnical analysis tools that assist engineers during the structural mapping process, allowing for greater and more representative data regarding the structural information of the rock mass, which may be used for generating DFNs. This paper presents the procedures used during a laser scan for characterizing discontinuities in an underground limestone mine and the results of the scan as applied to the generation of DFNs for further discontinuous modeling.INTRODUCTIONAccording to the Mine Health and Safety Administration (MSHA), between 2006 and 2016, the underground stone mining industry had the highest fatality rate in 4 out of 10 years, compared to any other kind of mining (MSHA, 2016). Additionally, during that same time, 40% of the fatalities were due to ground control issues, such as roof and rib collapses and pillar bursts. The National Institute for Occupational Safety and Health (NIOSH) developed guidelines for designing underground stone mines (Esterhuizen, Dolinar, Ellenberger, and Prosser, 2011). However, these guidelines do not apply to all underground stone mines.Monsalve, Baggett, Bishop, and Ripepi (2018) present a case study of an underground limestone mine experiencing a structurally controlled mode of failure. The authors analyze different methods to study that type of instability. They conclude that the integration of terrestrial laser scanning (TLS) with discrete element modelling (DEM) can be used to prevent rock falls in underground excavations to enhance worker safety. However, an adequate rock mass characterization and structural mapping must be performed in order to generate reliable models that allow the engineer to have a better understanding of the rock mass behavior."

Jan 1, 2018

By Morgan Sears

The LaModel program (Heasley, 1998) is a displacement discontinuity, boundary element model (BEM) for analyzing stresses and displacements in single and multiple-seam coal mines. After the Crandall Canyon mine collapse, the need for better design guidelines for LaModel was observed and a new calibration method for deep cover pillar retreat was developed (Heasley et al., 2010). However, the scope of this initial calibration was limited to single-seam mines deeper than 750 ft. This limited application of the initial calibration method lead directly to the research presented in this paper, which attempts to define appropriate LaModel calibration guidelines for pillar design where shallow cover and/ or multiple-seam mining scenarios are encountered. As part of this research, a database of shallow cover case histories has been developed, and this database is used to help validate the shallow cover calibration method. By adding the shallow cover database to the previous deep cover database, the LaModel calibration method has now been extended to the complete range of mining depths, as well as to multiple-seam cases. With this shallow cover calibration, the utility of the LaModel program continues to increase.

Jan 1, 2013

By Behdeen Oraee, Amirhossein Bangian, Kazem Oraee

"Determination of the optimum design of chain pillars has a significant effect on the economics and safety of longwall operations. Most pillar design formulae are based on empirical methods and supplemented by local experience. They therefore lack versatility of application under different geotechnical conditions.In this paper, in order to illustrate the shortcomings of the above, a typical real coal pillar in Tabas coal mine has first been studied and the conventional formulae have been used to determine the optimum dimensions. The results show that a wide difference exists between the predicted and the real field data. The Oraee-Hosseini formula has then been applied to this mine in order to determine the optimum design. The results from this formula demonstrate a close fit between the theoretical VALUES (and those produced by laboratory tests and in practice. It is further demonstrated that the wide discrepancy between the results obtained from the two formulae is attributed to the dissimilarities between geotechnical conditions of Tabas and the original regions whose data were used to devise the empirical formulae.It is finally concluded that the application of numerical simulation methods and experimental equations together with engineering judgment used by the mining design engineer, will provide the most accurate design characteristics.INTRODUCTIONLongwall is an underground mining method which has a high rate of production capacity and mechanization ability. This mining method, which is appropriately applied for soft rock fiatlying bedded ore bodies, gradually became a widespread mining method amongst European coal mines at the beginning of the 19'h century. It was then applied in some of the U.S. coal mines with the development of self advancing support mechanisms in early 1960's (Oraee, 2001).Underground coal production around the world using Longwall mining method doubled during 1990s. The main reasons for this improvement were: the high level of mechanization, increased 10 safety, adequate design of panels, and well designed ventilation systems (Peng, 2006)."

Jan 1, 2010

By Tobias U. Papst

The German Ruhrgebiet is slowly transitioning into a post-mining state. It has been subjected to industrial-grade hard coal mining operations for more than 150 years. Due to a political decision, German hard coal mining will come to an end in 2018. By then the surface will have subsided up to 20 meters. After all mining activities in the area have ended, there will be no need to maintain the current mine water level. Accordingly, the company operating the last remaining coal mines has decided to let the water level rise to an as yet undetermined level. Alongside other issues that may be caused by rising groundwater levels, the protection of the area?s drinking water supply is of utmost importance. This notion is also represented by European and German law. The primary intent of the applicable laws is to protect the health of the citizenship. This means protecting ground water that may be used by humans from being contaminated by the mine water. This paper outlines the consequences of European and German legislature on mining aftercare using the example of one of Europe?s largest agglomerations.

Jan 1, 2014

By Naj Aziz, Peter Craig

"Double shearing tests were carried out on the 28 mm (1 in) hollow strand Jennmar TG cable bolt to gain a better understanding of the shearing behavior of the cable. The first test was limited to a 50 mm (2 in) travel on the testing machine and produced a shear load of 900 kN (92 t) at the maximum 50 mm (2 in) displacement. The axial load generated on the cable bolt was 238 kN (24.3 t). In the second test, the machine travel was increased to 75 mm (3 in), and first strand failure of the cable, due to shear loading, occurred at 1,354 kN (138 t) vertical load at a vertical displacement of 59 mm (2.3 in). The cable axial load was in the order of 385 kN (39.3 t). Analysis of the failure mode and loads achieved showed that the cable strands bent and the concrete crushed along the shear plane; the shear loading across the concrete and grouted cable then reached the tensile strength of the steel wires.INTRODUCTIONCable bolts were introduced to the mining industry around 1970, initially to surface mining and underground metalliferous mining and then to coal mining in the early 1980s, mainly for roadway reinforcement as a secondary means of support. Cable bolts have since been used as both primary and secondary supports. As primary support, Fuller et al. (1994) described the application of cable bolts, known as FLEXIBOLT, for strata reinforcement in both Angus Place and Ellalong Collieries, in New South Wales (NSW), Australia. As secondary support, cable bolts have also been used as cable trusses, which act to support the immediate roof in a sling-like manner (Fabjanczyk and Tarrant, 1988; Fuller, et al., 1991; O'Grady and Fuller, 1992), and for reinforcement at higher stratification and beyond the rebar bolt length, mainly for anchoring lower strata layers immediately above the coal seam to the higher, competent bedding formation above. Initially cable bolt anchorage was by cementatious grouting and, since the 1990s, by chemical resin. The dominant type of cable bolts used for secondary support in Australian underground coal mines are 588 kN (60 t) capacity cables which are point anchored, pre-tensioned and post-grouted. Point anchored refers to a cable resin anchor. The cables are tensioned on the resin anchor; then the same cable is grouted by cementatious grout pumped to ·fin the annular gap around the cable from the collar of the hole to the resin anchor. Bulbs are located within the resin anchor section for mixing of the resin chemical components and efficient anchorage. The installation of these typically 8 m long cable bolts involves a lot of manual handling of the cables, lifting of heavy hydraulic tensioners, and exposure to resin grouts. Table 1 shows the specification of various cable bolts currently marketed and installed in Australian underground coal mines."

Jan 1, 2010

By Yongping Wu

Roadway deformation and stress migration occur with uncertainty and randomness because of geology, tunneling and mining influence. In order to study the surrounding rock deformation and failure mechanisms in three-dimensional stress state, an air return roadway of Yuanyang Lake mine of Shenhua Ningxia Coal Industry Group Co., Ltd. was chosen as a research object. The three-dimensional model was a designed and completed experiment with a dynamic-static coupling load. The model was loaded by hydraulic cylinder, simulating the in-situ rock stress field and the induced stress field of surrounding rock. The deformation monitoring system of the roadway model was constituted by optical total stations, borehole observation instruments, acoustic emission monitoring, and stress sensors. A wealth of data was obtained through an omni observation of surface displacement, characteristics of stress distribution, and deformation and failure of surrounding model material. By acoustic-optic-electric methods, a real-time testing on physical, mechanical, and damage parameters was realized through the experimental process. The results showed that the data of deformation and failure obtained from the deformation monitoring system of the roadway were authentic, which has great significance for warning and forecasting safety hazards of surrounding rock in coal mines.

Jan 1, 2013

By Uwe Wyink, Guenther Thiele, Isabel Gollnick, Klaus Thyrock

"The application of a thin spray on liner was implemented in longwall T-junction sections in 2009 for the first time. The development of the material and the application is based on a technical cooperation between RAG Deutsche Steinkohle AG and BASF Corporation. The report gives an overview of the first trials. The underground test occurred in a seam with a height of 1.5 m (5 ft) in a depth of 1,100 m (3,609 ft). The roadway is dual-use entry and the roof strata is composed of shale and sandy clay. In some sections geological faults impact the surrounding strata. The poor conditions induce separating and loosening of roof rock. Several remedial actions have to be implemented for decreasing deformations at the face entrance.The application of thin spray on liner (TSL) provides simplification and cost reduction of supporting work at longwall T-junction. The installation of TSL to avoid roof and coal fall operations for lagging are omitted.INTRODUCTIONFor safe operation of face retreat in dual-use roadways, the processes of securing and stabilizing the face end area are very important in order to minimize deformation and stress. Avoiding roof and coal fall are the main concerns for safe operation. For that reason different methods of reinforcement are tested in underground operation. In this paper the application of TSL is presented.The specifications of TSL are described, followed by the case study results. The underground study is located in one mine of RAG Deutsche Steinkohle. The extraction of the hard coal in this mine is characterized by great depth and high stress. There are poor geological and geotechnical conditions. The roadway used for the underground application was headed with the support system combination type A, which will be described later in the paper. After the first face retreat, deformation of steel arch support and bagging destroyed the roadway, so for the second face retreat remedial actions had to be undertaken. For this a new system of reinforcement, simplifying the supporting work at the longwall T-junction was tested. The reinforcement consisted of different parts that are described in the following report. Furthermore two different versions were applied. One method is the operation with TSL and the other one is the use of concrete for sealing. Both methods are compared in the text."

Jan 1, 2010

By Marvin B. Thompson

"The depositional model for major Illinois Basin coalbeds is well documented and defined on a regional scale. The model was a driving force during past exploration for lower sulfur and thicker coal deposits. The most attractive coal reserves were known to lie along the flanks of contemporaneous sandstone filled stream channels and were overlain by thick silty gray shale roof. At various distances away from the channels, the depositional model transitioned to black shale I limestone roof, sulfur content of the coal bed increased, and the coal bed often thinned. Understanding the character of roof rock types associated with this depositional model is essential to predicting ground control factors on both a regional scale, and on resolving roof control problems at the mine-site. Additionally, horizontal stress and overburden depth are significant factors that impact roof rock quality and ground control in Illinois Basin mines.Determining the character of several rock types, and defining the primary horizontal stress direction were crucial to a recent successful project at New Future Mine, located in southern Illinois. An inclined slope was constructed from the Illinois No. 5 Coalbed up to the Illinois No. 6 Coalbed through strata that ranged from extremely weak ""stackrock"" and a weak underclay unit, to a massive sandstone unit. Engineering geology, operations management, and Jennmar technical services personnel teamedup to select and install roof support for each strata transition. The project was completed with no injuries and no roof falls.INTRODUCTIONAbundant published information concerning coal deposition, geographic distribution, quantity, quality, and mining conditions exists for Illinois Basin coal reserves. The State of Illinois, through its State Geological Survey (ISGS), has provided decades of research, record keeping, and service to the coal industry. Other excellent sources of Illinois Basin coal information include the Indiana Geologiq1l Survey and the Kentucky Geological Survey. Past research by the U.S. Bureau of Mines (USBM) supplemented the work by the geological surveys, especially in the area of horizontal stress and mining hazards. The National Institute for Occupational Safety and Health (NIOSH) continues to produce publications focused on roof control issues common to many coal basins, including the Illinois Basin. Many of the illustrations in this paper originated in ISGS and USBM publications."

Jan 1, 2010

By Shengliyang Yang, Jinghu Yang, Jiachen Wang, Xiaomeng Li

"Safe and efficient mining of extremely inclined thick coal seams less than 20m thick is one of the new challenges in China coal industry. In recent years, the extremely inclined thick coal seams have been encountered in some old mines and western China, and currently the top coal caving longwall mining method has been successfully applied to this kind of coal seams. Accordingly, this paper studies the roof movement and its impact on shield supports of top-coal caving longwall mining in extremely inclined thick coal seams. The structure of main roof before failure was simulated by the fix-ended beam, and provided the solutions for determination of maximum compressive stress of the bottom beam end and maximum tensile stress of the top beam end. The failure mode on the upper end of working face is mainly a combination of compression and shearing, while that for the bottom end is tension and shearing. Roof fracture begins at the upper end of working and propagates downward. The shape of collapsed roof strata can be described as parabolic and divided into three segments from top to bottom, including no filling, uneven filling and densely filling segments. The roof loading conditions of no filling segment is more likely to have dynamic burst impacts.INTRODUCTIONExtremely inclined thick coal seam refers to that the dip angle of coal seam is greater than 45° and the thickness is greater than 3.5m (Wang and Zhang, 2015a; Wang and Zhang, 2015b; Wang, 2005; Xie, Gao, and Shangguan, 2005; Wu, et al., 2014; Deng and Wang, 2014; He, et al., 2015). This type of coal seams can be divided into three categories: 1. The extremely inclined thick coal seam, of which the thickness is less than 5m and the dip angle is less than 60°, is usually mined by fully-mechanized longwall mining method. 2. The extremely inclined thick coal seam, of which the thickness is 5 m-20m, is usually mined by top coal caving longwall method. And 3. When the thickness of extremely inclined thick coal seam is greater than 20m, it is mined by the horizontal section top coal caving longwall method. For example, the average angle ofWudong coal mine in Xinjiang province is 45°, and the thickness is 27m. Wudong coal mine is applying the horizontal section top coal caving longwall mining, producing 3 million tons annually per working face (Figure 1)."

Jan 1, 2016

By Jimenez Leon, Christopher Newman, Boede Gabriel, Zacharias Agioutantis

"Ground movements due to longwall mining operations have the potential to damage the hydrological balance within as well as outside the mine permit area in the form of increased surface ponding and changes to hydrogeological properties. Recently, the Office of Surface Mining, Reclamation and Enforcement has completed a public comment period on a newly proposed rule for the protection of streams and groundwater from adverse impacts of surface and underground mining operations (80 FR 44435). With increased community and regulatory focus on mining operations and their potential to adversely affect streams and groundwater, there is now a greater need for better prediction of the possible effects mining has on both surface and sub surface bodies of water.As mining induced stress and strain within the overburden is correlated to changes in the hydrogeological properties of rock and soil, this paper investigates the evaluation of the hydrogeological system within the vicinity of an underground mining operation based on strain VALUES (calculated through a surface deformation prediction model. Through accurate modeling of the pre- and post-mining hydrogeological system, industry personnel can better depict mining induced effects on ground water flows through the overburden material aiding in the optimization underground extraction sequences while maintaining the integrity of surface and subsurface bodies of water.INTRODUCTIONThe utilization of high-recovery underground mining methods, such as longwall or high-extraction room-and-pillar operations, have the potential to cause adverse impacts to both surface and subsurface bodies of water as strata movement and deformations propagate from the mined seam through the overburden to the surface (Peng, 2008).Previous research has indicated that mining induced strains are the most damaging to surface streams (Singh, 1992) as well as greatly affecting the integrity of subsurface bodies of water and groundwater flow conditions (Booth, 1986). On the surface, adverse effects to the stream can occur due to the development of either tensile or compressive strain in the stream bed. The development of tensile cracks along the bedrock allows for a potential loss of stream flow through developed fissures. In fact, water flow in the Cataract River of Australia ceased in 1994 as a result of mining-induced strains from longwall operations in the Bulli seam 430 meters (1320 feet) below the river gorge (McNally and Evans, 2007). On the other hand, the development of compressive strains within the rock layers can cause rupturing or buckling of the stream bed, blocking stream flow and/or diverting flow into the fractures at the base (Iannacchione et al, 2010). While these localized fractures can contribute to the loss of stream flows, given time, damaged streams have the ability to self-heal through the regeneration of near-surface aquifers as well as the sealing of mining-induced fractures with rock debris, gravel, sand, clay or other soil particles carried from upstream sources and deposited in the river bed (Waddington and Kay, 2002)."

Jan 1, 2016

By Richard R. Wilding

The United States Coal Mining Indus- try had the opportunity to greatly improve their roof control techniques during the nineteen seventies by the use of fully grouted resin roof bolts. This new tool was first approved for underground coal mines by M.S.H.A. ten years ago and during the next decade has been perfected to meet many problems previously thought to be unsolveable. The initial approved cartridge was very similar to the ones used in Europe in the nineteen sixties and since then has undergone a great deal of modification for our mines. These refinements in cartridge construction have been obtained by the close cooperation of resin manufacturers with mining personnel in perfecting pro- ducts customized to particular needs. This type of continuing program naturally necessitates a responsibility upon the resin anchor manufacturer to maintain a competant technical department. These roof control technicians by constant exposure to many of the most demanding underground problems, have developed through the years into leaders in successful applications. Today, Celtite has over twenty technically trained underground technicians with an accumulation of over one hundred years experience in resin anchors. Our documented technical reports are in excess of five thousand, involving over six hundred mines representing every major coal mining area in most mineable seams. This department has been the implement used to work with our research and development people in perfecting a continual line of improved resin anchors. This program has been a significant factor in leading the resin anchor industry into a position where approximately one third of the 1980 under- ground coal production used the fully grouted system. However, as gratifying as this accomplishment is, our experience has lead us to believe that there is an additional demand for a roof control system capable of combining the mechanical bolts ability to apply tension with resins proven superiority in anchoring. A significant number mines visited during the last decade had problems that we believed could be better answered by applying tension rather than the fully grouted approach. In most in- stances, their current mechanical installations were doing an adequate job until anchor slippage occured. Fully grouted systems solved this bleed-off problem. However, an acceptable number of falls still occured. In these some- what unique areas which we believe may amount to as much as fifteen percent of the total bolt installations, the need for improved anchors was a necessity. In developing this program we listed the ultimate requirements necessary for both the bolt and the anchor. These are for the bolt: A. Have one end manufactured so it can be grouted to the mine roof with polyester resin, obtaining a variable length from 12" to 36". B. Have a mechanism which allows the operator to tension the roof from zero to 10,000 psi. This mechanism should indicate if the roof is in compression and the bolt in tension. C. Have a mechanism which allows the operator to thoroughly mix the resin. D. The head of the bolt should not extend below the roof line any more than a normal mechanical bolt. E. Not require any extra tools for installation. F. Be bendable for use in low seam coal. G. Be durable and inexpensive. The ultimate point anchor resin should have the following characteristics: A. Have a mix and gel cycle which would compete with a mechanical bolt for speed of installation. B. Have a pull out strength in excess of a normal 5/8" mechanical bolt.

Jan 1, 1981

By Jiachen Wang

China is the largest coal producing country in the world. Coal is widely distributed in China and thus the mining conditions are complex and diverse. This paper summarizes the important achievements in the last 20 years in various mining methods including the extra thick seam with large mining height top coal caving, the thick seam with large mining height and top coal caving mining, the steep seam with top coal caving and fully-mechanized mining, the thin seam automated mining, and the backfill mining. At the same time, the rapid advance in the development of mining machinery and manufacturing has also contributed to the advancement of coal mining technology and the great improvement of coal mine safety. The future direction of China?s coal mining is to further improve mine safety as to improve the coal recovery rate, promote the pillar less mining technology, develop high-efficiency backfilling technology, develop steep seam high-efficiency mining technology for seams less than 10m thick, and high recovery mining techniques for extra thick seams, improve the reliability of mining equipment, and strengthen the protection and restoration of surface environments and water resources.

Jan 1, 2014

By Lorraine Kent

Comparison of in-situ stress overcore measurement results with those determined from laboratory evaluation of Acoustic Emission (AE) testing on oriented sub-core samples has been carried out for a variety of mining environments. These include UK and German Coal mines at moderate depth, shallow-level South African Coal mines and deep-level South African gold mines. Results show that the `Kaiser Effect' or 'Stress Memory-Damage is readily determinable throughout the brittle deformation process, although particular care is required in interpretation of results during the 'bedding-in' phase of testing and the region associated with unstable crack growth prior to failure. The results suggest that AE provides a useful complimentary method for comparison with existing methods of stress determination. The success of the method can, however, be dependent on both rock type and the likely magnitude of in-situ stress in comparison to the strength of the rock. Keywords: in-situ stress, acoustic emission, Kaiser Effect

Jan 1, 2002

By Chris Mark

Perhaps the most significant development in coal mine ground control during the last century was the introduction of roof bolting during the late 1940's and 1950's. From an engineering standpoint, roof bolts are inherently more effective than the wood timbers they replaced. Roof bolts promised to dramatically reduce the number of roof fall accidents, which then claimed hundreds of lives each year, and they were initially hailed as "one of the great social advances of our time." Roof bolting also emerged at a time of rapid technologic transformation of the coal industry, and greatly accelerated the transition to trackless, rubber-tired face haulage. The U.S. Bureau of Mines quickly became the new roof support's strongest advocate. Some state agencies and miners were skeptical at first, but nearly everyone was soon won over. Case histories were reported showing that roof falls could be largely eliminated while productivity increased dramatically. Little wonder that, in the words of one contemporary observer, "roof bolting has been adopted more rapidly than any other new technology in the history of coal mine mechanization." Yet by the end of the 1950's, it was clear that roof fall fatality incidence rates had actually increased. It would be another decade before the superior ground support provided by roof bolts would clearly save lives, The story of how roof bolting was implemented by the mining industry, but took so long to live up to its promise, is a fascinating example of the interaction between economics, technology, regulation, and science. It still has important lessons for today.

Jan 1, 2002

By Brent A. Slaker, Khaled M. Mohamed

"Understanding coal mine rib behavior is important for inferring pillar loading conditions as well as ensuring the safety of miners who are regularly exposed to ribs. Due to the variability in the geometry of underground openings and ground behavior, point measurements often fail to capture the true movement of mine workings. Photogrammetry is a potentially fast, cheap, and precise supplemental measurement tool in comparison to extensometers, tape measures, or laser range meters, but its application in underground coal has been limited. The practical use of photogrammetry was tested at the Safety Research Coal Mine, National Institute for Occupational Safety and Health (NIOSH). A commercially available, Digital Single-Lens Reflex (DSLR) camera was used to perform the photogrammetric surveys for the experiment. Several experiments were performed using different lighting conditions, distances to subject, camera settings, and photograph overlaps, with results summarized as follows: The lighting method was found to be insignificant if the scene was appropriately illuminated. It was found that the distance to the subject has a minimal impact on result accuracy, and that camera settings have a significant impact on the photogrammetric quality of images. An increasing photograph resolution was preferable when measuring plane orientations; otherwise a high point cloud density would likely be excessive. Focal Ratio (F-stop) changes affect the depth of field and image quality in situations where multiple angles are necessary to survey cleat orientations. Photograph overlap is very important to proper three-dimensional reconstruction, and at least 60% overlap between photograph pairs is ideal to avoid unnecessary post-processing. The suggestions and guidelines proposed are designed to increase the quality of photogrammetry inputs and outputs as well as minimize processing time, and serve as a starting point for an underground coal photogrammetry study.INTRODUCTIONThe stability of underground mine ribs has been a safety concern for underground coal mines for decades. Unfortunately, the average rib fatality rate has been about 1.3 per year between 1996 and 2013 (Jones et al., 2014). In an effort to better understand coal rib behavior, photogrammetry is being investigated in this study as a measurement tool for surveying ribs in an underground coal mine environment."

Jan 1, 2016

By John R. Poland, Benjamin Mirabile

"There are significant ground support hazards to both personnel and equipment when longwall equipment must mine through cross-panel entries. Backfilling support strategies are often cost prohibitive. Additionally, it is often very difficult to install backfill material in full contact with the mine roof in backfilled entries. This paper will demonstrate the use of fiber-reinforced concrete crib material as a method for standing support in longwall cut-through entries. Despite conceptions of poor performance in potentially high convergence environments, fiber-reinforced concrete crib material can be used in longwall support environments subject to high abutment loads and convergence. Central to the proper design of these supports is the use of yield material between crib layers and at the mine roof/crib interface. The placement location of cribs within the cut-through entry has a significant effect on the main roof behavior and associated ground conditions in the longwall abutment zones. It is particularly important to engineer the proper load displacement characteristics of the installed crib to support expected ground conditions. The cost of fiber-reinforced crib supports is less than 50% of backfilling methods.INTRODUCTIONThe design and execution of a longwall cut-through is perhaps one of the most difficult and risky endeavors in the field of ground control. The magnitude of abutment loads and potential for ground failure present a significant safety hazard to underground personnel. In addition, there is significant financial risk, with replacement costs of face equipment exceeding $200 million. Faced with these consequences, it is both advisable and common for an engineer to design ground support with a significant margin of safety. This paper outlines a robust support system that possesses a significant margin of safety along with significantly lower costs than most other support systems employed in similar conditions.SITE PARAMETERSThe mine site described in this study operates in the Herrin No. 6 seam in southern Illinois. The seam height is typically 76- 84 inches. Mining height in gateroads and mains is typically over 96 in, and typical mining height on the longwall face is 82 in. The overburden depth is 950-970 feet in the area of the longwall cutthrough."

Jan 1, 2016

By James Pile

The San Juan Coal Mine, located near Farmington, New Mexico, supplies the San Juan Generating Station with more than 6 million tons of coal annually. To replace dwindling surface mine production, San Juan installed a longwall in 2002. The roof rock in much of the underground reserve consists of interbedded coals, carbonaceous shales, and mudstones. Roof support consists of fully-grouted roof bolts, both tensioned and non-tensioned, supplemented by modified cable trusses. Short-encapsulation pull tests conducted by San Juan's geotechnical engineering department showed that some of the immediate roof layers provided variable bolt anchorage. To ensure that the roof bolts were obtaining the necessary anchorage, additional tests were conducted in a variety of locations. The results have been used to determine the optimum support design for different areas of the mine. Another series of tests evaluated the performance of several bolt and hole diameter combinations. The experience at San Juan Mine shows that short-encapsulation pull tests can provide the information necessary to improve ground control in variable roof conditions. It also illustrates how a pro¬active geotechnical engineering program can be an essential component of a state of the art underground coal mine.

Jan 1, 2003

By Kazem Oraee, Mehran Gholincjad, Navid Hosseini

"Chain coal pillars are pans of the structure of longwall mining system that play a significant role in the stability of the entries. With mechanization and developments in the various aspects of the method, higher efficiency in optimization of the design of chain coal pillars seems appropriate. In this paper the three main methods of chain pillar design, namely the empirical analytical and numerical methods arc compared. Real data from the Tabaslran coal mines have been used in order to make the comparison process reliable. It is concluded that the most apparent advantage of the empirical method is the reliability of the results while the use of numerical methods enjoys the advantage of flexibility. On the other hand the analytical methods are complex unless simplifying assumptions arc made that can substantially decrease the accuracy of result which is thought to be the main advantage of the design method. A new method is therefore introduced here that combines all of the three presently used methods and by doing so the new method has the advantages of the three while minimizing complexities and inaccuracies associated with the use of the individual methods.INTRODUCTIONLongwall mining is a high production method that can use mechanization to its full extent. Its initial development can be traced to 17th century European collieries but it was not until the second half of the 20th century with the development of self advancing support systems that the method gained popularity in the USA (Oraec. 2001). During the last decade, the production of longwall faces has increased significantly (Peng. 2006). The ability for mechanization along with good safety condition is the main reasons for such development. In the longwall mining method a good design for panel and entries on both sides, are two essential parameters. In this method, the thickness of overburden (depth of mine) nom1ally ranges from 60 to 20 m (197 to 2.7 9 ft) (Hartman, 2000) and with increasing mine depth designing for stabilizing the entries on both sides of the panel become more difficult. Thus, for safety and stability the size of chain pillar must increase. This causes the overall coal recovery to decrease and increase mining costs per ton. As such wide pillars hinder the air flow and hence ventilation costs increases too. Therefore with accurate identification of loading conditions and stress analysis. pillar that are a minimum size and sufficient safety factor are carefully designed."

Jan 1, 2010

By Nicholas P. Kripakov

The unpredictable massive collapse of roof in openings developed under apparently safe and stable roof conditions in coal mines of the United States has been of much concern for many years. One type of massive caving phenomenon is often attributed to cutter roof, a failure that initiates at one and/or both upper corners of an entry and propagates nearly vertically resulting in overall failure with little or no warning. This paper reviews current methods being used to control cutter roof and suggests new alternatives. The impact of basic parameters that include mine geometry, overburden geology, rock properties, and in situ stress conditions is discussed in the context of their relationship to this problem. The effects of various stress control measures are investigated with model analysis to gain insight into means of reducing the high level of stress known to exist at the entry corners of a West Virginia coal mine prone to cutter roof. The results are presented in the paper and the feasibility of their practical implementation is discussed.

Jan 1, 1982

By Jay Hilary Kelley

This paper proposes a modification of longwall roof support to meet new difficult mining conditions that are anticipated in the future. A gob canopy is a movable appendage attached on the rear of a longwall shield to counterbalance the troublesome forward downward force couple (FDFC). The gob canopy can be swung in both vertical and horizontal directions, powered by hydraulic cylinders. Several functions and applications are de- scribed

Jan 1, 1997