Search Documents

By Khaled Morsy

The studied mine extracts the Sewickley seam using room-and-pillar method. The overburden at study site ranges from 400 to 800 ft. Eight years earlier, the Pittsburgh seam was mined 80 ft underneath the Sewickley seam. Parts of the mains at the study site experienced problems of rib spalling associated with floor heave. Numerical modeling was used to explain the mechanism of ground control problems encountered at the mains of the upper seam. The modeling results show that the ground control problems encountered were caused by multiple seam interactions with the previously mined longwall panel of the lower seam. Based on the modeling results, a criterion to predict the probability of multiple seam interactions was proposed.

Jan 1, 2006

By David C. Oyler

The Bureau of Mines conducted research at the 9-Right Section of the Olga Mine to determine the cause of bumps and aid in the development of appropriate control techniques. The purpose of this paper is to identify the factors which affect the occurrence of bumps at the Olga Mine. These factors have been broken down into two categories, in situ and mining related. The in situ factors include those conditions which exist prior to mining, such as variations in lithology and overburden, presence of jointing, the composition and the physical properties of the rock, and the original stress field existing in the coalbed and adjacent strata. The mining factors include the mining sequence, changes in stress in the coalbed and adjacent strata during mining, rates of convergence, and the pattern of failure of the coal and adjacent strata. The factors which appeared to have the greatest effect on bumping were the overburden, the lithology of the roof and floor rock and the physical properties of the rock. The roof rock is generally a massive, stiff sandstone which does not break until coal pillar extraction is complete. The immediate floor is a strong shale which generally grades into siltstone and then into sandstone. The overburden at 9-Right ranged from 990 to 1,600 ft. Secondary factors appeared to be the in situ (pre-mining) stress and the mining sequence. When barrier pillars were split., pressures measured in hydraulic cells (Borehole platen flatjacks) located in those barriers showed large pressure increases, and the incidence of bumps increased, especially when the barriers were near old gob areas. The pillar extraction system used at Olga, where three rows of pillars are mined concurrently, appears to reduce pillar loads at the face areas, thereby reducing the exposure of men and equipment to the risks of bumps during mining operations. The horizontal components of in situ stresses at Olga were found to be nearly the same as those at 5 other mines in southern WV, where humps were not common, so it appears that horizontal in situ stress alone is not a major influence on bumping at the Olga Mine.

Jan 1, 1987

By H. Nan

Using the case of Qianqiu Mine, Yima Coal Mining Administration, theoretical analysis, laboratory physical simulation, and underground observation were performed to study the major parameters for fully mechanized sublevel caving mining method, including drawing spacing, drawing sequence, drawing numbers, and number of shields performing simultaneous drawing. The effects of those parameters on coal recovery and amount of waste rocks were also investigated. The optimal coal drawing technology for this case was obtained.

Jan 1, 2006

By Guo Junfeng

The strength of coal mass saturated with gas is an essential parameter in studying the mechanism of gas and coal outburst, and its prediction method. Up to now, there has not been a method for determining the strength of coal mass saturated with gas. This paper describes a new method whereby the strength of in-situ coal mass can be determined and stored continuously and automatically. The simulation results obtained in the laboratory indicate that the new method allows a fast, reliable, inexpensive and convenient determination of the strength of coal mass.

Jan 1, 1992

By Stephen J. Harven

Geologic conditions in eight northern operating sections of Jane Mine, Keystone Coal Mining Complex. Armstrong County, Pennsylvania are defined by utilizing drillhole data and underground geologic mapping. Three of the eight sections are experiencing difficult mining conditions in the Shelocta "0" coal seam (formerly the Lower Freeport). The five remaining productive sections will exhaust their reserves within one year. Coordinating mine planning with future production levels is aided by indicating areas that appear favorable and lack the geologic conditions that cause difficult mining. Roof rock 1 ithologies, lithologic variations in and below the floor, jointing, overburden thickness, coal splits, paleochannels. and clay veins are the principal geologic factors believed to influence mining conditions in Jane Mine. Careful definition of each cause allows for a reasonable assessment of future mining conditions.

Jan 1, 1987

By Michael Kelly

Inertial navigation technology has, for the first time, allowed the position of a longwall shearer to be mapped in three dimensions. Following the success of the technology in highwall mining and successful trials on a longwall face, the Australian Coal Association Research Program (ACARP) commissioned a three year "Landmark" project that aimed to advance longwall automation to the level of "on-face observation" by the end of 2004. This project has been completed with the following successful technical outcomes: Automatic face alignment was achieved, using an inertial navigation-based sensor on the shearer, to accurately measure face geometry and feedback signals used to move OEM (Original Equipment Manufacturer) roof supports. Operational on-line measurement of creep with creep information incorporated into face alignment corrections. Inertial Navigation System (INS)-based enhanced horizon control was bench-tested. Operational broadband communications system to shearer using wireless Ethernet on a commercial-product basis. Acquisition of located coal-face features for use in thermal infrared-based horizon control. Automated Longwall Information System (LIS) developed which integrates information from multiple systems and sensors and provides high quality visualisation and control interfaces. Automatic roadway and face convergence monitoring tools successfully tested. Condition monitoring tools developed and demonstrated for improved face reliability. This paper summarises the outcomes of the project and describes the work being undertaken for the 2 year Landmark Extension project approved in April 2005. Consistent with the conference theme, the paper focuses on the ground control aspects of the project.

Jan 1, 2005

By J. Nielen van der Merwe

This investigation was done to develop a method to predict the lie of coal pillars. It has long since been known that coal pillars deteriorate over time, but there was no method to quantify the deterioration. It was found that the rate of pillar deterioration was essentially a function of two parameters, namely mining height and time. The higher the mining height, the more rapidly the pillars deteriorated. The rate of deterioration is not constant, but decreases exponentially with time. The pillar life should be viewed in conjunction with the safety factor. While the relationship between safety factor and pillar life is ambiguous, the trend is nonetheless for higher safety factor pillars to have longer lives. The safety factor can be used to quantify a failure probability. The pillar life prediction indicates when the pillars which are predicted to fail, can be expected to do so.

Jan 1, 1998

By Srisharan Shreedharan, Gang Huang, Hongqing Song, Sijing Cai, Pinnaduwa H. S. W. Kulatilake

"Subsidence prediction due to ore extraction and backfilling during open stoping operations for an underground iron mine in China is reported in this paper. Geologic complexities including faults and interfaces between different lithologies, and the stoping and backfilling sequence adopted from the mine plans are incorporated in building a 3-D discontinuum numerical model. The stoping was simulated in two vertically stacked horizontal layers (Fig. 6), with a total of 16 stopes. Large displacements of up to 50 cm were predicted by the model along the roof of the stopes, and a maximum surface subsidence of 22.5 cm was predicted by the model . Backfilling was found to control subsequent deformation and subsidence. The extraction of the upper orebody led to relatively higher deformations in extracting the lower orebody. Finally, the predicted subsidences at all locations along a subsidence profile on the surface are shown. INTRODUCTIONThe Luohe iron (pyrite) mine, located in Hefei city, Anhui, is an underground mine in China, being mined through the open stoping and backfilling method. The orebody lies at a depth of about 400 m and has an average thickness of 250 m (Magang Steel Company, 2012a). Discovered in the 1960s, the location has a reserve estimate of 300 million tonnes, which have been mined since 2007. The orebody has been divided by the mining company into an east and a west section to facilitate planning for ore extraction.Figure 1 shows the surface above the underground mine, which is seen to contain many human settlements including villages, pastures and other infrastructure. These locations are sensitive in that they need to be protected from potential adversities due to the underground mining, such as surface subsidence. While it may be near impossible to completely eliminate the subsidence due to ore extraction, operations such as backfilling have been adopted by the mine in an effort to substantially reduce it. Hence, this paper focuses on describing the stability of stopes in the mine and estimates future subsidence in a part of the mining region through numerical modeling."

Jan 1, 2016

By Joe F. T. Agapito

High stresses and adverse geology in deep coal mines in the state of Utah, USA, have caused numerous bumps. The larger bumps have been associated with seismic events with Richter magnitudes of 3.6 and greater, and in some cases have filled openings for lengths of 150 m. A better understanding of the mechanisms and stress levels involved in bumping is needed to help develop improved stress control design and bump mitigation methods. The geology of the area is notoriously bump-prone. The coal has poorly developed cleating and occurs in multiple seams that are often bounded by very strong roof and floor sandstone/siltstone beds. The overburden is formed by thick, competent strata with numerous sandstone channels This geology and deep cover are the major source of high stresses, causing bumps. This paper evaluates live common stress factors responsible for bump problems: depth, sandstone channels, arching, faults, and coal thickness. It uses ease study data from longwall panels with two-entry/yield pillar systems typical of deeper Utah mines. Results illustrate the importance of analyzing stress factor experience to allow a better understanding of the problem.

Jan 1, 2000

By Christopher Mark

Colombia is 11th largest coal producing nation in the world, and the world?s fifth largest coal exporter. But while most of Colombia?s coal is mined at large modern surface mines located near the Caribbean coast, there are also underground mines that produce high-grade metallurgical coal. These mines employ traditional hand-loading techniques in a variety of geologic environments, and they have some of the highest accident rates of any Colombian industry. The National Institute for Occupational Safety and Health (NIOSH) has been collaborating with POSITIVA, the primary provider of worker?s compensation insurance to the Colombian underground coal industry, to reduce the economic and social cost of rock falls in these mines. The specific goals of the collaboration are to 1) document practices and conditions in Colombian underground coal mines, 2) identify relevant international best practices, and 3) provide recommendations for developing a national campaign to reduce fatalities and injuries associated with roof falls. NIOSH conducted a survey of seven underground coal mines in four separate coalfields. Five of the mines were characterized by steep dips and weak roof and floor rock. The coal was loaded by hand at all seven mines, though two employed partially mechanized longwall techniques. Wood posts were by far the most common ground support. Roof bolts were not observed in use at any of the mines, and they are unlikely to replace timbers any time soon. While long-term entries generally appeared to be adequately supported, the survey found that less attention was paid to the temporary support that is installed right after the coal is removed. This temporary support is critical for protecting the workers from rock falls, however, because with hand-loading mining methods most of the activity takes place between the permanent supports and face. The study concluded that improving the temporary support in the working faces would be the most effective way to reduce the number of rock fall injuries. The key principle should be that every worker is protected by planned roof support at all times. Ground Support Management Plans, consisting of specific rules about when, where, and what roof support is to be installed, should be the focus of the campaign. Each Plan should be tailored to a specific mine based on the geologic conditions and mining methods in use. The Plan provides miners with clear, simple rules that can be easily understood, while management can easily check to see if it is being followed. Ground Support Management Plans will also provide the campaign with a concrete focus for the necessary cultural change.

Jan 1, 2014

By Frank E. Chase

During the past quarter century, coal mine geologists have evolved from providing a qualitative description of drill core and coal reserves into quantitative geotechnical specialists who bridge the gap between geology and engineering. In the late 1970?s and early 1980?s, hazard prediction mapping was in its infancy. At best, hazard maps identified rudimentary structures and conditions such as stream valley locations, sandstone/shale transition zones, and lineaments. A ?technical disconnect? had existed between geologists and mining engineers as each profession operated largely independent of each other. Engineers did not readily integrate geology and geologic conditions, with the exception of coal thickness, into mine planning. Geologists were relied upon for reserve estimates and did not participate in mine planning or design. The employment and market slump of the 1980?s and 1990?s combined with mining more challenging reserves mandated that this gap be bridged and forced geologists to learn to speak more ?numerically? to engineers so they could be understood. The purpose of this paper is to describe the procedures and thought processes used by coal mine geologists when determining various mineability and reserve extraction feasibility issues. The paper will also address underground geologic hazard mapping and prediction techniques. To achieve these objectives, the opinions and experiences of leading coal mine geologists, geotechnical and strata control specialists across the United States were solicited.

Jan 1, 2006

By Collin Stewart

Bowie Resources, LLC (Bowie) has been using the Stability Mapping System (SMS) developed by Dr. Keith Heasley, West Virginia University, since 2005. Seven three-entry longwall gateroads, four longwall panels and a five-entry set of mains have been mined in two different seams in areas originally analyzed with the SMS. This paper compares predictions of mining conditions based on the SMS with actual mining conditions. Specific comparisons include longwall and continuous miner (CM) productivity, longwall tailgate response and support and CM roof bolting requirements. The paper also discusses current thoughts at Bowie on the use of different weighting factors for CM development, longwall face conditions and longwall tailgate support requirements.

Jan 1, 2007

By Frank E. Chase

The Harris No. 1 Mine, located in Boone County, WV, has been longwalling the Eagle Coalbed for over 30 years. Harris has experienced numerous interactions associated with the extensive room-and-pillar and longwall mining operations which have been conducted in the overlying No. 2 Gas Coalbed. The problems have included roof falls, excessive rib sloughage, and gateroad and bleeder entry closure. A detailed evaluation of the multiple seam experiences at Harris No. 1 Mine was conducted as part of the National Institute for Occupational Safety and Health (NIOSH) nation-wide multiple seam mining case history data base. One observation from the Harris gateroad case histories was that smaller, critically loaded, upper seam pillars seemed to cause more severe ground conditions than did wider pillars. The LaModel program was used to investigate this supposition, and the results confirmed that "critical" sized pillars do transmit the highest amounts of stress to adjacent seams. In addition, the data suggest that the probability of a major multiple seam mining interaction increases when the depth of cover is 1,000 ft or greater and when the Eagle seam pillars have a Analysis of Longwall Pillar stability factor less than 1.50.

Jan 1, 2005

By Vincent Scovazzo

This paper compares the two most common pillar design equations used worldwide by John T. Boyd Company; the Mark-Bieniawski Equation, an empirical approach, and the Wilson Equation, an analytical approach. The equations are compared in two ways; by their stress profiles and by the Mark-Bieniawski Equation stability factor. Contrasting the two equations based on the visual comparison of their stress profiles is straight forward but evaluating their resulting pillar designs is problematic. Complications arise due to the differences between the use and development of stability factors for empirical equations and safety factors for analytical equations. To work around these differences, comparisons are made between the two equations by first calculating pillar sizes using the Wilson Equation and then determining the Mark-Bieniawski Equation stability factor for these pillars. Pillars designed using the Wilson Equation were based on site-specific data from 23 mines located in the Americas and Australia. Comparing sizes of pillars designed by the Wilson Equation to the Mark-Bieniawski Equation; the Wilson Equation pillar sizes were smaller in 77% of the cases, similar in 3%, and larger in 20% of the cases.

Jan 1, 2008

By Zach Agioutantis, Christopher Mark

"Thirty years ago, the Analysis of Longwall Pillar Stability (ALPS) inaugurated a new era in coal pillar design. ALPS was the first empirical pillar design technique to consider the abutment loads that arise from full extraction, and the first to be calibrated using an extensive database of mining case histories. ALPS was followed by the Analysis of Retreat Mining Stability (ARMPS) and the Analysis of Multiple Seam Stability (AMSS). These methods incorporated other innovations, including the Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar strength formula, and the pressure arch loading model. They also built upon ever larger case history databases and employed more sophisticated statistical methods.Today, these empirical methods are used in nearly every underground coal mine in the US. However, the piecemeal manner in which these methods have evolved resulted in some weaknesses. For example, in certain situations, it may not be obvious which program is the best to use. Other times the results from the different programs are not entirely consistent with each other. The programs have also not been updated for several years, and some changes were necessary to keep pace with new developments in mining practice.The Analysis of Coal Pillar Stability (ACPS) now integrates all three of the older software packages into a single pillar design framework. ACPS also incorporates the latest research findings in the field of pillar design, including an expanded multiple seam case history data base and a new method to evaluate room and pillar panels containing multiple rows of pillars left in place during pillar recovery. ACPS also includes updated guidance and warnings for users and features upgraded help files and graphics.INTRODUCTIONPillar design is one of the fundamental elements of mining engineering. Pillars are necessary to control the great weight of the overburden during all phases of underground mining. Without stable pillars, ground control is impossible."

Jan 1, 2018

By Lixun Kang

Bedded structure is the characteristics of coal measures strata. Bedding planes, coal streaks and soft rock bands existing in roof strata destroyed its continuity in the direction perpendicular to the coal seams. The statistics from a large number of long wall faces in which serious roof fall accidents occurred in Datong coal mining area suggest that beddings planes, coal streaks, soft rock bands, especially the first layer thickness of immediate roof have a great influence on its stability. As the first layer thickness increases, the probability of serious roof fall accidents decreases. Based on the investigations finite element method is used to analyze stress and displacement in the first layer of immediate roof. The results indicate that the thicker the first layer is, the less the roof convergence in the unsupported area is. Stress and strain features in stratified immediate roof are quite different f7om those in non- bedded immediate roof. In stratified immediate roof, every stratum has each own tensile zone in the upper portion and compressive zone in the lower portion, while tensile zone in the first layer is less, the tensile stress is the greatest.

Jan 1, 2005

By Jin He

Based on the simple-beam theory, a stress analysis model was established for undermining in multiple seam strip-pillar mining when the strip pillars were not columnized; the effects of various mining factors (e.g., mining depth, inter-burden thickness, recovery ratio, etc.) on inter-burden stability were analyzed; the changes in inter-burden stress distribution were investigated; and the important role that the inter-burden spacing and the mining width of the lower seams on inter-burden stability was studied. Finally, the actual practice used in Feng Feng Mine area was used as an example to demonstrate the rational mining width for a fixed mining depth.

Jan 1, 2006

This paper is not available for inclusion in the Proceedings at the time of printing, but it will be included as an insert.

Jan 1, 1984

By Gennaro Marino

Documented case histories are studied where data were found on the initial collapse of the overburden above the longwall panels. Under this scenario, the most controlled conditions exist for assessing the span capacity of the overburden (i.e., before failure the roof spans to fin coal abutments on two to all four sides). In an attempt to correlate theory to field observations, data are used on the overburden lithology, and the depth, width, and face advance of the panel, as well as, the subsidence conditions noted on the surface. The subsidence measured on the surface is used to determine when complete failure in the over- burden rock has occurred.

Jan 1, 1987

By Michael Gauna, Christopher Mark

"For decades, pillar recovery accounted for a quarter of all roof fall fatalities in underground coal mines. Studies showed that a miner on a pillar recovery section was at least three times more likely to be killed by a roof fall than other coal miners. Since 2007, however, there has been just one fatal roof fall on a pillar line. This paper describes the process that resulted in this historic achievement. It covers both the key research findings and the ways in which those insights, beginning in the early 2000s, were implemented in mining practice.One key finding was that safe pillar recovery requires both global and local stability. Global stability is addressed primarily through proper pillar design, and became a major focus after the 2007 Crandall Canyon mine disaster. But the most significant improvements resulted from detailed studies that showed that local stability, defined as roof control in the immediate work area, could be achieved with three interventions:• Leaving an engineered final stump, rather than extracting the entire pillar;• Enhancing roof bolt support, particularly in intersections, and• Increasing the use of Mobile Roof Supports (MRS)A final component was an emphasis on better management of pillar recovery operations. This included a focus on worker positioning, as well as on the pillar and lift sequences, MRS operations, and hazard identification. As retreat mines have incorporated these elements into their Roof Control Plans, it has become clear that pillar recovery is not ""inherently unsafe.""The paper concludes with a discussion of the challenges that remain, including the problems of rib falls and coal bursts.INTRODUCTIONPillar recovery has always been an integral part of underground coal mining in the US. When room-and-pillar methods are employed, large blocks of coal in the form of pillars are initially left in place to support the weight of the overburden. Unless these pillars are subsequently recovered, the coal they contain will never be mined."

Jan 1, 2016