Search Documents

By D. T. Iseley, A. L. Atta-alla

INTRODUCTION The extension project of the East Line Subway of Atlanta's subway network includes the construction of two single track transit tunnels under Interstate Highway 285. The project will be in DeKalb County, Georgia. The length, width, and height of each tunnel are 54.25, 6.3, and 7.2 m (178, 21, and 23 ft) respectively. The ground cover above the tunnel crown ranges from 1.5 to 3.25 m (5 to 11 ft). A soil pillar about 5.5 m (18 ft) wide will remain between the tunnels. The construction of each tunnel includes (i) installation of 21 steel soil support pipes of 75 cm (30 in) diameter, (ii) jet grouting 15 soil cement shafts of 60 cm (24 in) diameter in the soil under the pipes, (iii) contact grouting behind the tunnel lining and between soil support pipes and pavement, (iv) excavation of soil inside the soil support arch, and (v) installation of steel pile foundation, steel sets, and permanent tunnel lining of cast-in-place concrete, all as shown on the cross section in Fig. 1. The soil profile can be described from top to bottom as cement/asphalt concrete pavement, a fill layer consisting mostly of stiff sandy silt/firm silty sand, a residual soil layer consisting mostly of silty sand/sandy silt, partially weathered rock, and solid rock.

Jan 1, 1991

By J. A. Farinelli

In the Appalachian region of the United States, approximately 40% of the underground coal reserve base exists in seams 0.7 - 1.1m thick. These seams are, in general, often of premium quality and are frequently accessible through above-drainage drift-type openings. Unfortunately, there are no apparent advantages to mining thin seams, if quality is disregarded. The thin-seam mine is faced with the same legal and economic pressures as any other underground coal mine. But in addition to these common problems, thin-seam operations must also deal with the unique problems associated with mining at such a restrictive height. Small-scale, short-lived operations appear to be the most feasible means of mining these reserves. The purpose of this paper is to evaluate the production and safety potential of various thin-seam mining systems. Recommendations will be made regarding present and future thin-seam operations.

Jan 1, 1987

By Haydn H. Murray

Kaolins and bentonites of economic importance in Australia and New Zealand are described. Clays that are used for structural clay products are not discussed. Residual, hydrothermal, and sedimentary kaolins are utilized including clays associated with coal measures. Bentonites are sedimentary and residual. Very little kaolin and no bentonite is exported presently, but this will change in the near future as transportation costs continue to escalate. Many areas of Australia, in particular, where kaolins are known to occur have not been investigated to determine the quality and quantity of the deposit.

Jan 1, 1982

This paper provides a summary on the use of the POL YCOM high pressure grinding roll (HPGR) for increasing extraction in copper leaching. The energy-efficiency and significant hydrometa1lurgical benefits of the HPGR result in better acid-curing, higher solution application rates, improved copper extraction from various copper minerals and better recovery from high acid consuming ores. The HPGR's metallurgical features such as micro-fracturing, better liberation of disseminated and veinlet copper, increased oxygen and lixiviant penetration lead to higher copper extractions than achieved by conventional crushing. Flowsheet options, operational characteristics and applications for various copper ores are outlined.

Jan 1, 1996

By John Todhunter

Longwall mining is certainly not new in the United States, having first been used in the late 1800's in Illinois, but the surging acceptance of the method is relatively new. The number of longwall installations in this country are nearly doubling annually as this method continues to prove itself as a coal producer's delight terms of operating cost, performance and safety. Since 1951, several longwall installations have been tried in Barnes and Tucker Company operations. Although all efforts actually proved that the system itself could be used in prevailing conditions, it was not until 1967 that a unit was put in use that proved competitive with regular mining equipment, both conventional and Continuous.

Jan 1, 1968

By D. Watson

The Henderson mine has more than 20 years experience and has placed a combined total of more than 400,000 m3 (520,000 cy) of shotcrete and concrete. Over the last 20 years the mine has used a variety of equipment for placing concrete, wet shotcrete and dry shotcrete and is constantly trying to cut costs and increase efficiencies. Henderson has recently received a state of the art wet shotcrete placer, automated its batch plant, fabricated a mobile concrete form jumbo and is soon to receive a new concrete transport truck.

Jan 1, 1992

By Jr. Neudecker

Rock melting technology can provide in-situ glass liners in nuclear waste package emplacement holes to reduce permeability and increase borehole stability. Reduction of permeability would reduce the time and probability of groundwater contacting the waste packages. In-creasing the stability of the storage boreholes would enhance the retrievability of the nuclear waste packages. The rock melting hole forming technology has already been tested in volcanic tuff similar to the geology at the proposed nuclear waste repository at Yucca Mountain, Nevada.

Jan 1, 1989

By Duk-Won Park

Since geologic anomalies are one of the governing factors of instability of underground openings, it is extremely important to know in advance the locations and extent of these anomalies such as faults and weak zones. At an underground coal mine in the Black Warrior Basin, core drilling was conducted to find a fault in an area where they were planning to locate longwall panels and possibly a shaft. Core logging did not provide sufficient information to delineate the exact location, strike, and dip of the fault. However, a high resolution reflection seismic study successfully solved this problem. This experience proved the seismic exploration technique could be used for premining coal exploration by reducing drilling costs and providing more accurate and detailed information about geologic anomalies.

Jan 1, 1988

By H. Evans

It is well known that iron-ore pellets are considered one of the best blast-furnace burden materials used today. The demand for pellets is demonstrated by the increase in pellet output from one million tons in 1955 to approximately 37 million tons in 1964. This growth continues as new plants are placed on-stream each year. The consumer generally specified (1) the acceptable content and range of chemical constituents, (2) a minimum strength determined by some standard testing procedure, (3) the size range of pellets, and (4) perhaps a measure of reducibility.

Jan 1, 1966

By T. J. van der Walt

This paper proposes a new methodology to model ill- defined processing operations using neural nets (NN's). A process with many variables (large dimensionality) cannot be modelled adequately if limited process data are available. This problem of multi-dimensionality is addressed and an approach suggested to reduce the dimensionality using NN's. The result of this modelling methodology is a combined model of phenomenological expressions and NN's. The model can successfully be incorporated in a dynamic simulator of the process. A new approach to conduct modelling on the basis of continuous data collected directly from an industrial processing unit, is also proposed. The modelling methodology is applied to a typical processing operation, the resin-in-pulp (RIP) process.

Jan 1, 1992

By Kostas Fytas, Sebastien Perreault

This paper presents EOLAVAL, an integrated mine ventilation design software. In its new expanded version it is a user friendly and fully interactive computer package. The features of the new version are a graphics interface fully compatible with Autocad files, an integrated database of fan characteristics and the optional use of the thermodynamic approach in carrying out network simulations. This software can be used in underground mine ventilation planning: mine ventilation network analysis and simulation, economic design of airways, auxiliary ventilation design, calculation of a mine air heating plant, and evaluation of the natural ventilation and pressure losses in a mine shaft. This paper presents a case study illustrating the use of the computer package in mine ventilation design.

Jan 1, 2002

By George A. Lawrence

A new super-large 100 m3 (3500 A3) pneumatic mechanical flotation cell is now available to meet future mineral processing challenges. Several innovative design concepts represent a marked departure from conventional flotation cell designs. The radial discharge from the pump action rotor and the overhung vane type stator is contained in a conical bottom cylindrical tank with no dead comers. Peripheral launders collect froth overflowing the entire circumference of the tank and these launders are of a hexagonal design permitting cells to be nested together in a honeycomb fashion. This new flotation cell is powered by a custom designed hydraulic motor package that provides infinite speed control in individual cells and a soft start under load

Jan 1, 1993

By G. M. Bernard

An overview presentation of the fast-track start up of Cerro Colorado, a new copper heap leach project in Chile's Atacama' desert. A brief explanation 'of location of the property, exploration history, geol-ogy, reserves and development are presented. The overview includes mining, crushing, agglomeration, and the solvent extraction-electrowinning recovery process. Challenges and requirements specific to heap leach systems will be addressed and analyzed. A detailed description will be given of the mobile heap leach conveying and stacking systems used in the building of heaps for on-and off-pad operations.

Jan 1, 1995

By R. B. Hoy, Stanley J. LeFond, Unni H. Rowell, K. Reckling, Derek G. Fullerton

In 1989 natural industrial diamonds counted for 55% of the world's natural diamond production. Australia is currently the leading producer (35%). Zaire is the second largest producer (19%). of what is primarily industrial grade rather than gem grade. Botswana (17%) is third, with the former USSR (15%) fourth, and the Republic of South Africa (8%) fifth. Diamonds are also mined in Angola, Namibia, the Ivory Coast, the Central African Republic, Ghana, Tanzania, Guinea, and other African countries. In the Western Hemisphere, Brazil is the principal producer, with some production from Venezuela and Guyana [(Fig. 1)]. A very small output of diamonds is mined today in India, which was the first source of commercial production. In the United States, efforts at commercial diamond mining have been confined to a small area near Murfreesboro, AR. The first diamond was found in a pipe there in 1906. Small scale trial mining has not, however, proved economical. Since diamonds were first discovered more than 2,000 years ago, only about 380 t have been mined. In order to obtain 1 g (5 metric carats) of diamonds, it is necessary to remove and process approximately 25 t of rock. Recovering this small percentage involves a combination of highly developed techniques in mining and extremely sophisticated processes in diamond recovery. END USES Diamonds are used for two unrelated end uses: gem diamonds are jewels of great beauty, while industrial diamonds are essential materials of modem industry. Although imitation stones are substituted for the gem diamond, none of these matches its properties sufficiently well to offer real competition. Synthetic industrial diamonds are now of a quality and size that permit them to be substituted for natural diamonds in numerous industrial applications. For example, synthetic diamonds are available today in sizes up to 100 stones per carat (1.2 to 1.4 mm). In addition, polycrystalline synthetic diamond inserts, such as De Beers Syndite", General Electric's Compaxa and Stratapax", and Megadiamond's Megapax" have replaced natural diamonds in turning tools, mining and oil drilling bits, and dressing tool applications. Industrial Diamonds The diamond is by far the most important industrial abrasive. As recently as 50 years ago, consumption of industrial diamonds was less than that of gem diamonds, but since that time, industrial use has grown to a position of great dominance. During the six-year period 1929 to 1934, the material produced for industrial use amounted to about 74% by weight of the world's total output of diamonds. In 1989 the percentage of natural industrial diamonds mined in the world was 55%. When synthetic industrial diamonds are added to the natural industrial diamond figures, this percentage becomes 87% of total world diamond production including gems, near gems, industrial, and synthetic stones. The many uses responsible for these significant increases are dependent on the properties of the diamond, including hardness, cleavage, and parting, optical characteristics, presence of sharp points and edges, and capacity for taking and maintaining a high polish. The utilitarian role of the diamond was confined primarily to lapidary products until the industrial revolution, which created the first demand for diamond as an industrial tool. In 1777, a British inventor and instrument maker, Jesse Ramsden, used a diamond to cut a precision screw for an engine that he had invented. The first authentic description of industrial diamonds being set in a saw was recorded in 1854 by a Frenchman, Durnain. Eight years later a Swiss watchmaker, Jean Leschot, developed the first diamond drill bit for use in a hand operated machine, which was employed to drill blastholes in rock. In 1864, diamond bits were put to their severest test up to that time in the construction of the Mont Cenis Tunnel in the Alps. A few years later a steam-powered diamond drill with a speed of 30 rpm was able to penetrate rock at the modest rate of 0.3 m/hr. As the industrial revolution gained momentum on both sides of the Atlantic, metal replaced wood and machines replaced people. Thus the foundation was laid for precision engineering and the recognition of diamonds as an indispensable tool of industry. The next major demand for industrial diamonds came after World War I with the development of cemented carbide cutting tools. Diamond was found to be the most effective medium for finishing and grinding the new ultrahard metal. This discovery rapidly increased the demand for industrial diamonds. The availability of inexpensive diamond material inspired tremendous research into applications. By 1935, the first successful phenol-resin grinding wheel containing diamond had been marketed. Soon afterward, the metal-bonded and vitrified diamond wheels were produced, and, as the matrices and bonds that held the diamond grit in place began to improve, the popularity of diamond grinding wheels grew. The outbreak of World War II, and the accompanying increase in use of hard-metal tools in the munitions industry, increased the demand for industrial diamonds. Since about 1950, the development of ultrahard ceramics, semi- conductor materials, plastics, and exotic metal alloys has further consolidated the diamond's position as an indispensable tool of industry. Only diamond is hard enough to cut these superhard materials with the precision, speed, and economy that industry demands today. Special machines equipped with industrial diamonds are used to remove bumps from concrete runways and highways and to modify highway surfaces in order to prevent skid accidents. Many skids are caused by hydroplaning, a phenomenon that occurs when the roadway is wet. Tires mount a film of water and virtually lose contact with the road surface. Diamond machines cut neat, narrow

Jan 1, 1994

By Charles N. Speltz

The cost of transportation of industrial minerals frequently is higher than the cost of the product. When a mine, industrial-mineral plant, or customer is served by a single railroad, because of the lack of competition, that railroad may in- crease rates and/or reduce service so that the economics of that mine, plant, or customer are affected adversely. Transloading of industrial minerals from rail-to-truck or truck-to-rail to improve economics and sales of product is not a new concept. However, transloading to create competition and reduce freight costs or to improve service is a relatively new concept brought on by the recent mergers of many of the main-line railroads, both in the eastern and western United States. For example, in 1998, with completion of the Burlington Northern/Santa Fe (BNSF) and the Union Pacific/Southern Pacific mergers (UPSP), the western United States has only two main-line railroads. The industrial-mineral producer, to reduce the cost of transportation or increase the level of service, must evaluate potential transloading opportunities in light of higher prices and reduced service brought on by reduced railroad competition. This paper discusses industrial-mineral transloading and examines the case history of the Tucker Hill perlite project in southern Oregon. The Tucker Hill project is a classic study of industrial-minerals transloading where the project would have failed without the transloading.

Jan 1, 1999

By Erik A. Munroe, Nelia W. Dunbar, Virginia T. McLemore

In New Mexico, there are at least 100,000 abandoned mine waste rock piles with widely ranging geochemical and mineralogical compositions. A geochemical and mineralogical study was implemented for five waste rock piles, some which contained sulfides, in the Hillsborn Mining District. Chemical and physical characteristics of mineral grains and their secondary mineral oxidation rinds were examined with the electron microprobe. Pyrite and chalcopyrite appear to be the most reactive to oxidizing conditions. Clays, iron oxide, iron hydroxide, iron sulfate, and primary texture rinds exist in the waste rock piles analyzed.

Jan 1, 2000

By Siegmund Babendererde

1. Introduction In Sayreville, New Jersey, the Middlesex County Utilities Authority put the construction of a 1041 m long sewer outlet to tender in June 1989. It had an internal diameter of 3,36 m and was part of a sewage treatment works project for county Middlesex. The contract was awarded to the Lodigiani Company, USA, who employed Hochtief Incorporated as subcontractor to drive the sewer outfall. 2. Ground Conditions According to the preliminary geological site investigation, carried out by the consultants Metcalf & Eddy, the tunnel passed through marine deposits.

Jan 1, 1991

By R. J. Snoby, P. Grotjohann

In processing heavy-mineral sands, the low feed concen¬tration and respective high value of the desired minerals require high-capacity production and sharp classification/ separation techniques to reduce the specific production costs. This paper describes the new allfux® separator, which can economically accomplish these criteria. The separator is a two-stage process that combines rising current and fluidized-bed technology. This allows for the treatment of ex¬tremely high mass flows in a single unit. This paper reports on test work performed on coal, iron ore and heavy minerals.

Jan 1, 2000

By M. Imazu, Ö. Aydan

"A new rock classification, Rock Mass Quality Rating (RMQR) proposed by the authors is briefly explained and its application for the design of tunnels and large underground openings support systems is described in this paper. RMQR is an index to evaluate the state of rock mass. The preliminary support design may be based on the concept to prevent structurally controlled failures of rock mass. RMQR can also evaluate the yielding characteristics of rock masses so that it is possible to design a support system to prevent or control the deformation of surrounding rock through the utilization of the proposed rock mass classification and some analytical and numerical techniques.INTRODUCTIONThe first three authors proposed a new rock classification system named Rock Mass Quality Rating (RMQR) (Aydan et al. 2014). RMQR quantifies the rock mass state, and using the classification system together with intrinsic geo-mechanical properties of intact rock, possible geo-mechanical properties of rock masses can be estimated. The instability modes of underground openings can be structurally controlled because of the orientation of discontinuities in rock mass and the in-situ stress induced (Aydan 1989; Aydan et al. 1993, 1996; Aydan and Genis, 2010). The authors (Aydan and Ulusay, 2013; Aydan, 2016) have also tried to apply this system to the design of a tunnel support system. The authors presented initial guidelines for the RMQR classification system earlier (Aydan and Ulusay, 2013).In this paper, the authors provide further guidelines and establish some criteria for support system design that considers loading conditions and types of underground structure according to RMQR. Guidelines are alsos proposed for selecting the proper size of rockbolts, rock anchors, shotcrete, steel ribs and concrete liner. These guidelines are based on past experiences with various underground structures, theoretical understanding and the anticipated behavior of rock mass under given in-situ stress conditions and excavation techniques. The authors also utilized some databases developed for large underground caverns and tunnels excavated in squeezing or rock-bursting ground conditions."

Jan 1, 2016

By L. MacHue

Sulfur containing collectors have been shown over the years to function as strong, selective and non-selective sulfide mineral collectors. Unfortunately, the majority of the widely known sulfur based collectors are of low molecular weight, volatile and subsequently, possess an objectionable odor. Higher molecular weight sulfur based collectors (C9 and higher) are significantly less odiferous due to lower volatility and lower vapor pressures. In this study, a specific proprietary higher carbon number collector, Orfom® MC 37, was blended and used successfully to recover 2-3% additional molybdenum in a laboratory flotation system, when compared to a standard collector blend. Copper recoveries were also positively affected. Further testing is required to give additional conditions favorable to increased copper and molybdenum recoveries, but indications at this time show the proprietary sulfur based collector blend to be a selective collector of molybdenum, while providing a significant increase in copper recoveries.

Jan 1, 2010