Search Documents

By George J. Dvorznak, Robert W. Waytulonis

The Bureau of Mines is conducting a research project in cooperation with the Mine Safety and Health Administration (MSHA). Mining companies, and equipment manufacturers are also participating through the Colorado Mining Association (CMA). The objectives of this cooperative research project are to determine the practicality of coupling a dry exhaust conditioning system (dry system) and diesel particulate filter (DPF) to make an integrated control system, and to determine the effectiveness and durability of the integrated system in an underground coal mine. Diesel-powered mining machines must be equipped with control devices to reduce surface and exhaust temperatures to safe levels and prevent flames and sparks from being emitted to the mine atmosphere. Diesel exhaust-gas water scrubbers have been successfully used for many years but they have several disadvantages; they are large, consume large quantities of water, and require frequent maintenance to remain functional. Additionally, diesel exhaust is a source of noxious gases and particulate matter. Particulate emissions are composed primarily of small carbon particles with absorbed hydrocarbons and they are almost entirely respirable in size. Even an engine in good mechanical condition can emit up to 400 mg/cu m of respirable particulate matter. A dry system for control of diesel fire and explosion hazards, coupled to a DPF, promises to be a complete control system for diesel engines. The dry system cools the exhaust and suppresses sparks and flame with a heat exchanger and flame and spark traps. The conditioner is smaller, consumes no water, and requires less maintenance than a comparable water scrubber. The DPF uses a ceramic substrate as a wall-flow filter and is very efficient at collecting exhaust particles. Average particulate mass collection efficiency is 90%. This report describes a cooperative research project to combine the dry system with the DPF, conduct performance tests on the integrated system at Bureau and MSHA 1aboratory facilities, and conduct field tests of the system on a production machine in an underground coal mine.

Jan 1, 1987

"INTRODUCTION The characterization of groundwater hydrogeology is a common component in feasibility studies, geotechnical investigations and regulatory permitting for mining operations. The lithology at a location of interest may include several discrete water-bearing units; and the means of isolating each for testing can be accomplished through the use of inflatable packers. Consideration for testing during drilling program planning and communication between all stakeholders is essential to ensure that the Mine, Drilling Contractor and Hydrogeological Testing Specialist (Specialist) are ready to perform packer testing when the call is made to mobilize. Often, the notice to mobilize can be delayed and then occur with little warning due to the issues that can occur during drilling of very deep boreholes, as well as other factors. Hydrogeological investigation reports and journal articles generally discuss testing methods and results, with limited information available describing the planning and coordination of the field testing program, as evidenced by the lack of references cited below. The source of inspiration for the subject matter of this paper is grounded in the author’s past shortsightedness; with the hope that others not share similar misfortunes but experience success through thorough preparation for their future hydrogeological testing programs. The sections below focus on the planning stages of a field investigation using inflatable packers, including considerations for site specific conditions, designation of stakeholder responsibilities, and communication of testing expectations. Following these sections is a presentation of two examples of successful field programs and lessons learned in addressing problems encountered along the way. PRELIMINARY PROGRAM PLANNING & CONSIDERATIONS From the onset of planning for drilling programs, the Specialist should be in communication with the Mine to review plans and identify fatal flaws which could impede collection of hydrogeological data. Preliminary scope decisions can significantly affect the budget and duration of hydrogeological field programs and may dictate the means by which the field data is collected. The issues that need to be considered include the following factors. Testing Objectives The setup of the packer tool is dependent on the testing objectives. Is the goal to estimate bulk aquifer hydraulic conductivity or to identify discrete discontinuity hydraulic characteristics? Are groundwater samples needed? The answers to these questions affect selection of test interval length and what instrumentation might need to piggyback on the packer tool. Identifying the testing goals initially will provide adequate time to prepare packer equipment for mobilization. Borehole Size While inflatable packers come in many shapes and sizes, some sizes are more readily available and easier to procure on short notice. Packers for NQ and HQ size boreholes have been historically easy to procure and are commonly used in exploration drilling. Packer equipment is available for smaller holes, but it becomes more difficult to fit instrumentation down-hole as the borehole size decreases. This is particularly a consideration if collection of groundwater samples is required. In addition, risks of losing the hole or equipment downhole are greater for smaller boreholes. Larger boreholes require larger packers and clearly require more effort and heavier capacity machinery to manually manipulate due to the increased size."

Jan 1, 2017

By Bok-youn Kim

Presently, mobile diesel equipments contributes a lot in improving the economical feasibility of underground mining and tunneling operations. Even in Korea, quite a large number of diesel equipments is being applied to the underground workings already. This paper introduced the production procedure, characteristics and evaluation technology on diesel particulate matter(DPM) that is known as a carcinogen For easy measurement of DPM using laser dust monitor, the conversion factor(K) to gravimetric concentration was acquired. The field measurement of DPM was conducted to make a comparison between locally manufactured on-road equipments and imported equipments specially designed for underground use. According to the Government regulation revised h 1996, it was learned that the critical pollutants among the diesel exhaust is DPM instead of NOx which have been considered as a critical pollutants.

Jan 1, 1997

By P. Berendsen

The tectonic and sedimentary environment of the Central North American Rift System (CNARS) provides all excellent setting for major mineral deposits. Major north-northeast-trending high-angle normal or reverse faults and northwest-trending transcurrent fault systems may exercise control over ore forming processes. Gabbro and basalt are the dominant igneous rock types. Carbonatite and kimberlite occur in Nebraska and Kansas. Concentrations of Cu. Ni, Co, Ti, Au. Ag and PG-minerals are known to occur in this setting. Arkosic sandstone, siltstone, shale, and minor carbonate units occur on top of the rift basalts and in flunking basins where they may reach thicknesses of 10 km (6 miles). The potential, for stratiform or unconformity-related metalliferous deposits must be considered. The rift as a whole remains, however, largely unexplored.

Jan 1, 1990

By J. P. A. Hortley

In conventional electrolytic copper production, looped copper starter sheets, on which the copper is deposited, are supported by hard-drawn copper bars. These bars have cross-sectional areas of between 1 and 1.4 in2. The suspension bars serve two purposes: firstly to support the cathode, which can weigh up to 150 kg, and secondly to introduce the electric current. IYI examined these two requirements in detail to see whether a better design could be achieved. Considering firstly the current carrying requirement, it wee noted that under normal refinery conditions, each cathode carries between 400 and soak. If one applies the generally accepted rule that 1 in of copper can carry 1000A4 a suspension bar need theoretically contain only 1/2 in2 of copper. This contention is supported by the fact that the 500A current passed through the cathode also appears to pass quite satisfactorily through the two support loops, which have a cross-sectional area of approximately 0.35 in 2. Turning now to the strength requirements, the cross-section of hard-drawn copper bar required to support a 150 kg cathode is relatively small, and easily met by the present designs. It is not, however, the static load applied by the 150 kg cathode immersed in the electrolyte which causes the damage to the hard-drawn copper, or even the increased static load of a 100 kg man standing on one foot in the centre of the bar; the damage is actually caused by the dynamic loads applied to the bare when they are dropped, thrown into containers, lowered too rapidly into the cell, or otherwise mistreated. The important requirement is therefore that the bar does not permanently bend. Its proof stress of limit of proportionality, rather than the amount that it deflects under static loading, should be the strength criterion. With the hard-drawn copper normally used for the manufacture of suspension bars, it has been observed that the copper becomes annealed during use, particularly at the end of the bar where the current is introduced. Thus, after a relatively short time, the cathodes are in effect being supported by annealed copper bars.

Jan 1, 1978

By D. W. Park

Longwall mining is popular in underground coal production in the United States due to higher production rates and safety concerns. Because of the extreme complexity, it is necessary to plan an adequate design to achieve a safe and efficient working place. The proper sizes of yield and abutment pillars and panels can be determined by simulation using numerical modeling techniques. By means of three-dimensional modeling, stresses to be imposed on the pillars, panels, gob, and powered supports can be analyzed. In this study, an initial three-dimensional finite element model was developed and then modified into four different models. Using these models, the numerical outputs of distributed stresses on three different sizes of yield pillars, three different sizes of panels, and two different sizes of abutment pillars were compared and analyzed to determine the most adequate pillar and panel sizes. Progressive failure theory based on the Hoek and Brown failure criterion was used to determine redistribution of stresses in the yielded and failed areas in the longwall mine.

Jan 1, 1992

By A. Konya

"INTRODUCTION Underground Mining and Construction projects face several challenges unique to the underground environment compared to the surface environment. The goals of an effective blasting program are the development of a blast pattern that minimizes cost, maximizes face advance, and provides the desired fragmentation and face profile. In addition to these , mines must consider the very real operational problems that occur such as drill deviation, ground vibration, and deadpressing or sympathetic detonation of explosives. These operation problems lead to increased costs and decreased production in the mine, hurting the bottom line. Combined with these problems, underground blasts can be difficult to monitor and evaluate due to tight spaces, dust during the blast obscuring video, and the need to evacuate the immediate area with no clear line of sight to observe performance. This creates an environment which most mines know that blasting can be improved in their underground operations, yet most are hesitant to change due to fears of the shot freezing, misfires occurring, and questions about how to achieve a proper design. The explosive companies and shot service providers also offer limited assistance or knowledge in the underground blasting realm, unlike with surface blasting, leaving many underground operations in the dark. It is for these reasons that most underground operations are operating decades behind the current technologies and incurring significant costs, both real and hidden, from there blasting operations. This paper discusses philosophical changes to designs that need to be made for effective design and modifications of underground blast patterns to prevent deadpressing and precompression of modern explosive products (Konya, Konya, & Worsey, Modern Blasting Method Selection, 2017). While numerous different methods of underground heading development exist, there are two types that are used in a majority of mines around the world, these are the burn cut and the V-cut. The burn cut is a parallel cut that has holes that go straight into the face and are primarily used in smaller opening (due to ability to pull deep rounds with smaller room widths) and metal mines (helps in ore dilution and greater fragmentation). The V-Cut is a cut that uses angled drilling towards the center of the face (in the traditional method) and is primarily used in underground aggregate operations due to its cheap cost but larger fragmentation sizes and greater throw of the muckpile. This paper will discuss these two forms of cuts specifically with the understanding that modifications to these can be applied to other parallel and angled underground heading techniques. BURN CUT The burn cut is one of the older forms of underground blasting, where a part of the blast (burn) of a shot is heavily loaded with additional empty (relief) holes with the goal of smashing (aka burn) and pushing/blowing all the material in the burn out to provide relief for subsequent blastholes. The relief holes in the burn cut provide a parallel relief for the holes that are firing to break too creating a second plane of relief, however these are extremely small and can cause many problems if a design is improper."

Jan 1, 2018

By M. F. Corcoran

Rapid advances have been made in the past few years in the application of automatic controls and instrumentation to iron ore pelletizing plants. Present practice in applying instrumentation and control to the Grate-Kiln system of iron ore pelletizing is described. Major control points and loops are tabulated. Future trends in the application of digital control including computer data logging systems are described.

Jan 1, 1965

By K. H. Al-Rawahy

Appreciation and awareness of the unique nature of mineral investment and ultimate development of a mine are crucial in promoting sustainable development. Special characteristics of mineral development include high capital intensive, long pre-production period, high risk, and the unavoidable ?economic? depletion. This paper examines ways to integrate these unique attributes of the mineral industry into the educational process, so that a properly advised and knowledgeable culture in terms of a sustainable mineral industry can be developed. Specific approaches are investigated in order to achieve this objective. These include a stochastic evaluation of a mineral investment proposal, adding a premium to the cost of capital that is used for valuation process, and internalizing incidental costs to the private cost function, thereby realizing the true (vs. apparent) marginal social cost of the proposed development. Undoubtedly, a total evaluation of any mineral project that accounts for both tangible and intangible parameters will contribute to sustainable development objectives. By incorporating the practical application of apparent theoretical topics such as risk, probability, and externality, and their relevance and impact on mineral lifecycle (prospecting, exploration, development, exploitation, use, and ultimate disposal) into the educational process, it is hoped that a generation of technocrats and decision makers that are familiar with and concerned about sustainable development will emerge.

Jan 1, 2007

By D. L. Passmore

The development of microcomputer software that provides an analysis of pit-specific accident and production data for the mining industry is seen as a vital component in a total loss-control system. The Mine Injury Reporting System (MIRS) allows users to access accident and production data prepared by the Health and Safety Technology Center of the Mine Safety and Health Administration of the United States Department of Labor for any particular state and to generate a simple, yet informative, report.

Jan 1, 1988

By Jane Morrison

Permanent magnets are used in most electromechanical and electronic devices to convert electrical to mechanical energy and vice versa. More than fifty are commonly found in the average American home and car. A new species of permanent magnet composed of iron, neodymium, and boron has recently been developed which combines superior magnetic properties with compact size. The reduced size of the magnets has enabled significant new developments in such areas as robotics and consumer electronic, among others. The objective of the present work is to efficiently and economically separate valuable rare earth materials from the relatively worthless iron constituent in NdFeB magnet scrap. Several magnet producers have expressed interest in the development of such a process and have provided information and scrap samples to aid in research. Scrap is generated in a variety of forms from different stages in the processing stream. Pieces of magnetic and non-magnetic metal as well as sludge and ribbon from jet casting must all be treated. Beneficiation techniques have been studied and size distributions developed for the different scrap types. Slag from the casting process is resistant to crushing and may need to be embrittled first, but all other types are amenable to crushing and ball mill grinding using stainless steel balls and water. Tabling was found to be useful in classification of magnet sludge. Two major techniques for separation of rare earths have been studied:

Jan 1, 1990

The Chinese city of Shanghai is one of the fastest growing in the world. To keep up with the growth, two tunnels, three-lanes each, are being built beneath the Yangtze River to connect Shanghai with the Changxing River Island. To complete such a large project, Herrenknecht Tunneling Systems was brought in to construct the largest tunnel boring machine (TBM) in the world. The first Herrenknecht S-317 Mixshield has a diameter of 15.43 m (50.62 ft). It was built to construct one of the two 7.2-km (4.5-mile) tunnels. The tunnels are part of the Changjiang Under River Tunnel Project and will be at depths of up to 65 m (213 ft) beneath the Yangtze River in Shanghai-Pudong. These two tunnels are to be opened to traffic in April 2010, in time for Shanghai to host the World Expo. More than 20 million people live in the Shanghai area. The area itself has been growing at an extremely rapid pace for more than a decade and is in need of more space. The search extended beyond the natural limits of the Yangtze River Delta. As part of its incredible growth, 500 new vehicles are registered every day. The new tunnels will connect the Changxing River Island, with a population of approximately 600,000 people to the road traffic network. A bridge construction will also provide a traffic link between Changxing Island and the large island of Chongming.

Jan 1, 2007

By G. A. Hufford

The cutoff grade applied to a disseminated orebody mined by open pit affects both the waste ratio, hence the cost of producing ore, and the ore grade, hence the quantity of metal recovered. As such it has a significant impact not only on the annual profit or loss, but also on the life of a mining property. Cutoff Grade Strategies Some commonly used objectives in calculating cutoff grades are as follows: Minimize Unit Cost of Product (1) This is found by adding all costs associated with each possible cutoff such as mining, processing, and marketing. This is divided by the quantity of marketable product obtained at each cutoff grade, then finding the minimum. Because the market value of the product does not enter the calculation it has no effect on this strategy: the same cutoff is selected in good times and bad.

Jan 1, 1986

By G. M. L. Robinson

Mineral Processing Wastes, as defined by the Environmental Protection Agency (EPA), has determined that most of the mine wastes will be regulated pursuant to subtitle D (Solid Waste Regulations) of the Solid Waste Disposal Act while specific mine waste categories will be regulated within the framework of the Toxic Substance Control Act. Though EPA's determination currently relieves the industry of the regulatory constraints mandated by the Resource Conservation and Recovery Act (Hazardous Waste Regulations) Subtitle C regulatory framework; the industry is not granted immunity from historical or current environmental regulations related to listed or characteristically hazardous or solid wastes. Because of the current regulatory trends and the need to implement cost effective remediation alternatives; advanced currently available on-site remediation technologies are available to minimize, reduce, contain or prevent environmental impacts related to mining and processing activities. In light of industry technical needs, an overview of the research and commercially available remediation technologies will be discussed and a brief discussion of the strengths and weakness of each technology will be presented. Technologies to be discussed includes stabilization, solidification, soil wash, soil flush, thermal distillation, pump and treat, metal extraction, centrifuges, filter presses, bioremediation, and incineration.

Jan 1, 1992

By D. A. Norrgran, J. A. Marin

Introduction The recent development of rare earth permanent magnets has revolutionized the field of magnetic separation. The advent of rare earth permanent magnets in the 1980s provided a magnetic product that was an order of magnitude stronger than that conventional ferrite magnets. This allowed for the design of high-intensity magnetic circuits that operated energy free and that surpassed electromagnets in the strength and effectiveness. New applications and design concepts that focused on the mineral and metal processing industries have evolved. This technology led to the development of various magnetic separators specifically designed for mineral processing applications. Applications that were not previously considered are now being used in primary mineral upgrading, recycling and secondary recovery. Historical perspective Lodestone was the first naturally occurring permanent magnetic material known. Lodstone was most likely used to upgrade iron ore by early civilizations. By the 1600s, the early magnet technology had advanced to quench-hardened iron-carbon alloys. The practical significance of magnetic separation was formally recognized in 1792 when an English patent was issued for separating iron ore by magnetic attraction. By today's standards, carbon steel is a very poor magnet material. It is easily demagnetized and has a very low energy product of much less than I MGOe (Million-Gauss-Oerstads). This was state-of-the-art technology for almost 300 years until chromium was added to magnet feedstock, which resulted in a three-fold increase in the energy product. The well documented addition of cobalt to permanent magnets in 1917 initiated the 30-year era of "Alnico" magnets that at the time provided a superior magnetic energy product. Since then, the science of magnetism has advanced rapidly and is now considered a highly developed branch of physics and material science. Permanent magnets have had an extremely long history. Figure 1 presents a chronology of permanent magnets that illustrates the increase in energy product. Amazing developments in material science have taken place in the last two decades. The gradual advancement of permanent magnet technology was shattered in 1967 with the initial development of samarium-cobalt (rare earth) magnets. Since that time, the advent of neodymium-boron-iron magnets provided such an increase in energy product that new design concepts were considered. New avenues of study were introduced by the complexities in the material science and physics involved in describing these new permanent magnets. Furthermore, applications for permanent magnets that were previously not considered were now viable. Rare earth elements Rare earth elements have claimed the attention of scientists for the past century. These elements were originally termed "rare" because they were thought to be quite scarce. Since then, however, geological studies have shown them to be relatively abundant. The discovery and identification of rare earth elements is complicated by the inherent difficulties in separating them from each other. The rare earth elements comprise the fifteen transition elements of Group IIIB, Period 6, of the periodic table. These elements extend from lanthanum to lutetium and are commonly called the lanthanide series. Samarium and neodymium are the two most common elements used in the commercial manufacture of rare earth permanent magnets. Commercial grade rare earth magnets There are only a few common types of rare earth magnets that are considered in the circuit design for magnetic separators. Early rare earth magnets of commercial significance (introduced in 1970) consisted of the first generation of sintered SmCo5. The energy product of these magnets ranged up to 23 MGOe, which provided the initial impetus to the field of high-energy permanent magnets. Although these magnets did not produce the extremely high magnetic field strengths of current rare earth magnets, they were relatively temperature stable. Containing 66% Co, they are the most expensive of the basic commercial rare earth permanent magnets. Their use is limited today because they are being replaced by second and third generation rare earth permanent magnets.

Jan 1, 1995

By R. D. Shackleton

Medusa Cement Company, a division of Medusa Corporation, is a medium-sized cement manufacturer serving the midwest, east, and southeast. Medusa's eight plants are located in Georgia, Pennsylvania, Ohio, Illinois, Michigan, Wisconsin, and Canada. Of these, six have active limestone, shale, clay, and sand quarries now in operation. This paper deals with the various individual state laws regulating mining and reclamation at the Georgia, Illinois, and Pennsylvania quarries. Several recommendations for future state mining laws are discussed also.

Jan 1, 1974

By H. E. Bonner

The recovery of fine coal has historically had limited success due to the intimate clay association on the surfaces of the coal particles. This clay presence has detrimentally affected conventional beneficiation techniques resulting in a recovered product containing unacceptably high concentrations of ash and moisture. An ultrasonically activated tray that operates in a continuous fashion has been developed that separates the clay film from each particle's surfaces. This separation is of sufficient duration to allow conventional beneficiation techniques to be utilized more efficiently.

Jan 1, 1989

By J. den Drijver, M. Opahle, R. Inderst

Safety reasons render necessary the advanced calculation of the amount of methane degassing from a longwall in the scope of the ventilation planning of mines. Today empirical methods, which are based on observations of operational procedures, are used for the calculation of the amount of methane. Despite of constant improvement those calculations are not always sufficient. In particular calculations which are based on operational facts but not proved by experience are not reliable. Most of all these calculation procedures lack physical-analytical descriptions of the procedure itself, presenting only the effects on important parameters such as the distance between seams in the roof or floor or gas pressure. Tschersich [Tschersich 961 developed an analytical model for an advanced calculation by analysing the degassing of seams in the roof and floor and the physical parameters of gasflow. This model might correct the lacks of existing procedures and improve the precision and reliability of additional calculations. The model simulates the emission record in seams of the roof and the floor. It takes into account not only a multitude of parameters such as the distance to adjacent seams and gas pressure but also the depth of seams, gas content, rank of carbonification, rock temperature, face advance rate, initial and succeeding mining and the face length. In order to comprehend and to verify those correlations we extended the model of Tschersich and programmed this enlarged model using the computer language C++. Aim of this research is to guarantee a much higher accuracy in calculating methane emission caused by mining. The improved planning is expected to result in more safety and better prevention of high methane con- tent in ventilation as well as in a better use of the capacity of the mining equipment. The application [Drijver, lnderst 961 of the ex- tended model will also be very useful in the course of research projects as it allows computer simulation, i.e. in-situ research can be extensively limited or even replaced.

Jan 1, 1997

The last twenty years of development in Process Mineralogy are reviewed. Since the milestone review by Henley in 1983, which projected the concept and suggested closer working relations between mineral processing and mineral science, the second generation (1983-2003) has made significant progress. Examples are to be found in improved sampling and high-confidence flotation testing, and in automated quantitative mineral measurement. The recent addition of end-member studies has provided a clearer view of the overall ore mixture milled from its constituent geological components. In all, better predictive abilities have resulted from these improvements to Process Mineralogy. These improvements have led to more significant business impacts in mineral resource characterization, and in optimization of existing concentrator operations.

Jan 1, 2004

By J. J. Daniels

Advances in borehole geophysical research for mineral assaying and remote detection of mineralization away from the borehole are cited. Nuclear activation measurement research has provided accurate in situ assays of economic metals with neutron-gamma activation, using a high resolution intrinsic-germanium detector. Although nuclear activation analysis is the present "best hope" for obtaining in situ assays for some elements, gamma-gamma and magnetic susceptibility measurements can provide accurate assays for lead-zinc and magnetite, respectively. Borehole optical spectroscopy and X-ray fluorescence are being investigated as possible in situ assaying techniques for some minerals. More laboratory and field calibration research is needed before non-linear complex resistivity (NLCR) can be routinely used as a quantitative assaying tool. Field tests have shown that variations in the local geologic environment can affect the quantitative accuracy of assay values from downhole NLCR measurements. Deeply penetrating borehole geophysical methods are increasingly being used for mineral exploration as drilling costs and exploration have increased. Borehole electrical measurements have been shown to be useful for detecting conductive ore bodies that are not intersected by a drill hole. Hole-to-surface resistivity and surface-to-hole time-domain electromagnetics are demonstrated to be particularly effective for defining mineralized zones in a massive sulfide environment. Borehole gravity meters and three-component magnetometers have been developed and should prove useful for defining geologic anomalies away from the drill hole.

Jan 1, 1987