Search Documents

By CAIJUN CHEN, MING ZHANG, ZHENWEI WU, FENG ZHOU, BOQUAN LI, XILIANG ZHANG, ZHOU PU

Traveling grate is a widely used process for iron ore pellet production, but the thermal state of pellets in the drying section is still unclear. In this study, the temperature distribution of the drying section was investigated using computational fluid dynamics (CFD). The results indicate there is a coupling effect in the drying section of a traveling grate. Gas with higher temperature in down-draught drying (DDD) transfers heat to the up-draught drying (UDD) through the gap of the insulation board, and the temperature gradient of the pellet bed changes before reaching the insulation board. The characteristics of pellet bed expected to appear in DDD are displayed in UDD in advance. To verify the model, a contrast experiment was conducted.

By R. V. Ramani

In 1970, of the 603 million tons of coal produced in the United States, 339 million tons, or 56%, were produced by under- ground mines. While the ratio of underground to surface production has been decreasing in the last few years, it is anticipated that a 60:40 ratio of underground to surface-mined coal will remain for some time. Underground coal operators are continuing to invest in new mines and are interested in increasing the efficiency of all their operations. One area for improvement is in mine planning and design, particularly in the area of selection of equipment for operation. Because of the availability of a wide variety of equipment, a fair degree of selectivity can be exercised in the choice of equipment for a particular job. However, such a choice must be made on the basis of technological facts and forecasts related to the mining operation. If the mining conditions can be reasonably predicted, along with a mining plan, it should be possible to insure the selection of the right equipment for the particular application. In order to increase the efficiency of underground coal operations, it is necessary to understand not only the operating system in detail, but the inter-relationships between system components and the operating environment. With such an understanding comes the application of simulation and other operations research techniques to plan and operate mining systems. Computer simulation studies have been successfully adapted to underground coal mining, and applications by Prelaz et al. (1965), and Manula and Sanford (1969) are some that are being used by the mining companies. However, a need still exists for better understanding of certain intra-system and system-environment interactions in order that computer simulation programs may be provided with better input data for more effective application. This paper deals with one aspect of the coal-winning system in need of better definition, namely, studying the performance of continuous miners.

Jan 1, 1973

By Kathleen Y. Knoebel

This paper describes a graphical mini computer system called MPASS 2 (Mine Performance Analysis/Simulation) which has been designed to conduct analysis of underground room-and-pillar mining operations using both conventional and continuous mining methods. Dynamic, graphic displays of mine face machine activities are presented on the CRT screen to provide extensive visibility into underground mining activities. MPASS 2 consists of: an interactive inputting system that graphically creates a room-and-pillar mine and describes the mine when production is initiated; a time-step simulator that produces statistical summaries of shift activities and uses CRT screen graphics for accelerated-time display of machine activities and delays; a statistical analysis subsystem for analyzing mine performance data; an industrial engineering system that permits users to enter actual machine activity statistics and replay mine operations on the CRT screen; and a data management system to store historical performance information on mine characteristics and operations. MPASS 2 operates on a Hewlett-Packard 9845B mini computer with 450 K bytes of extended memory, and is written in H-P BASIC. It has been installed at Freeman-United Coal Mining Company in West Frankfort, Illinois and at the U. S. Department of Energy Pittsburgh Mining Technology Center. Applications include production system simulation, industrial engineering analysis, production scheduling, new equipment evaluations, and training.

Jan 1, 1982

By I. G. Ediz, D. W. Dixon, W. M. Fidler

In this paper a new method for the arresting of tunnel explosions is presented. In the proposed technique, the on coming explosion is detected by a pressure sensitive device by a pre-determined rise in static pressure. The sensor then triggers a mechanism which causes the explosion door to be closed in a specially constructed concrete barrier zone. The doors are of a special construction and consist of perforated steel plates that allow part of the blast wave to be transmitted but do not allow the passage of the flame. A number of design parameters have been identified, including: the likely amplitudes of the transmitted/reflected pressure waves that would govern the explosion door pressure loading; thickness of the perforated steel packages; perforation dimensions; heat transfer across the door and other factors.

Jan 1, 1995

By H. Maleki, G. Tetreault

This study was initiated by the US Bureau of Land Management (BLM) to develop guidelines for determining the maximum economic recovery of resources in coal mines. The work was in response to a requirement in the Mineral Leasing Act of 1920 and Federal regulations. The intent was to address the economic rainability of small, irregular reserves in existing longwall mines. In particular, there was a need to determine if room- and-pillar mining using a continuous miner (CM) was economically sound or whether unconventional (short or odd-shaped) longwalls could be used to recover small coal reserves economically. Small reserves, called "widgets " are left in longwall mines on one side of the mains near outcrops and adverse geological conditions or near any other location where reserve geometry does not lend itself to mining with a rectangular longwall panel. The work included the analysis of the geologic, geotechnical and economic factors that influence the recovery of small coal reserves; the analysis of historic changes in supply, demand and coal prices; the development of typical cost models for room-and-pillar and longwall mines; and the development of a practical methodology for determining maximum economic recovery. The methodology included an evaluation of the ratio of coal mined during longwall mining to that mined for development (LDR), as well as costs of maintaining coal quality depending on market conditions. The LDR is a good indicator of mine efficiency and overall coal recovery in modern longwall mines and, thus, is used to evaluate the increased costs associated with adding new development sections for extraction of small reserves. The study examines the economic feasibility of using unconventional longwalls for the recovery of medium-sized reserves, depending on site-specific geologic and geometric conditions.

Jan 1, 2002

By Roy M. Fleming

During the decade of the 1970's, a new emphasis was placed on assuring a safe and healthful workplace for all American workers. Much of the basis for this national effort was federal legislation: the Occupational Safety and Health Act of 1970 and the Federal Mine Safety and Health Act of 1977 (amended from the 1969 Coal Mine Act). One of the agencies involved in this protection effort is the National Institute for Occupational Safety and Health (NIOSH) of the Centers for Disease Control (CDC) in the Department of Health and Human Services (DHHS). In fulfilling its mandates under the 1970 and 1977 Acts, NIOSH conducts research, experiments, and demonstrations to support and stimulate advancements in health and safety practices. Priorities for NIOSH research are established primarily through congressional mandates, requests from the Department of Labor, needs as defined by NIOSH researchers, and surveillance information. Emphasis is placed on research in the areas of toxicology, industrial hygiene, physical and chemical sciences, physiology, ergonomics, engineering, psychology (behavior and motivation), and epidemiology (industry-wide studies). The framework of the current Institute program to identify, evaluate, and control occupational hazards includes activities in surveillance, research, evaluation, and training. These activities are planned and evaluated through a system that coordinates the efforts of eight research and scientific divisions. Each division develops projects to address program areas that have been identified by NIOSH management as having highest priority. In surveillance programs, the objectives are to identify substances and agents found in a representative sample of workplaces and to collect and evaluate information on rates of disease and injury in occupational groups. Information is also collected on occupational safety and health programs implemented by industry. Estimates of worker exposures and the potential for adverse health effects are considered in setting priorities for further investigations. A related activity, which also serves to provide technical assistance to industry, is NIOSH's Health Hazard Evaluation program. On-site investigations of workplaces are made in response to worker, employer, or government agency requests. Both industrial hygiene and medical examinations are conducted, and the results contribute to identifying new problems and evaluating their significance which may have public health implications beyond the particular worksites that are investigated. Field and laboratory research projects are performed to meet several objectives: - Characterize the working environment by evaluating current and past exposure levels for workers who are included in epidemiological or medical investigations. - Develop epidemiological information to define the association between the substance or agent under investigation and the acute and chronic health effects on workers. - Determine through animal studies the parameters of an association between exposure and effect. - Investigate the etiology of disease. - Develop sampling and analytical instruments and techniques and demonstrate their application for measuring toxic materials in the workplace. - Formulate sampling strategies that will accurately and precisely indicate exposure levels. - Develop medical procedures to prevent disease and to detect the presence of disease and early indicators of disease. - Assess the technology for control of exposures, including engineering and administrative techniques, personal protective equipment, and work practices. Presently, the research program is focused on reproductive effects, neurotoxic effects, injury/trauma, lung disorders, cutaneous disorders, cardiovascular disorders, cancer, stress-related disorders, effects of physical agents, digestive disorders, and renal and other organic disorders. In studying these issues, priorities are determined by the seriousness of possible adverse health effects resulting from occupational exposures, the feasibility of studying existing records or obtaining new data, and the size of the population which is potentially affected. Where there is low level of suspicion concerning adverse health effects or where an occupational disease occurs in a variety of industrial environments, investigations are limited to gross analyses of health effects such as review of mortality patterns. In such studies, the industrial populations selected are those for which existing data resources can be utilized. Such data consists of records of occupational exposures or health status which have been maintained by the employer, the union, or Government agencies. Where a review of the available information suggests that serious health hazards exist and the existing data resources are inadequate for quantifying the relationship between the specific biological response and type and degree of exposure, prospective studies are initiated. Information derived from such research is essential for the development of sound criteria for control of industrial exposures to noxious agents. Other input to the criteria documentation process comes from searching and evaluating the literature. Criteria documents contain the recommendation of an environmental limit where information is available to support it, as well as the recommendation of work practice controls, medical evaluation, information for workers to recognize and avoid the hazard, and identification of specific research gaps. In some cases, during the criteria document preparation, gaps in knowledge are found which necessitate further research before an occupational standard can be recommended.

Jan 1, 1981

By S. Mertikas

The purpose of this paper is to set the stage for (1) the determination of the specifications and actions required for a successful development of a system for the management of waste deposits and contaminants resulting from activities in the mineral industries and landfills and (2) the appropriate infrastructure to be developed at the industrial level. The design of this system would be such that its application could be extended to other industries as well. Waste deposits and contaminants from activities in the mineral industries and landfills commonly cause damage to the environment. In addition to precautionary measures aiming to protect against environmental impact, early warning and immediate response to mining hazards and contaminants is a requirement for sustainable development. Hazard detection and control requires continuous and real-time detection techniques, as well as methods for tracing and predicting the motion of contaminants and waste products. The efficient accomplishment of these goals in the minerals industry requires developing an integrated system for environmental monitoring using remote sensing technologies, in combination with advanced image analysis and geostatistical techniques.

Jan 1, 2003

By Jozef Descour, Kazunori Nishioka, David M. Neil

Designers, engineers, and contractors are using three-dimensional seismic tomography for geotechnical site investigations and during tunnel excavation for hard rock and soft ground applications. Utilizing multiple types of seismic signals produced by a TBM, drill, or impact breaker, the reflection of different velocity features are processed into a holographic image of the actual structure to be encountered. The Mill Creek Phase 3 alignment in Cleveland, Ohio, was imaged to define existing conditions along a 1,200-ft section of a proposed 6.1-m (20-ft) diameter CSO tunnel and, specifically, a zone of expected anomalous conditions where drilling was inconclusive. In Japan, Kajima Corporation used TRT™ to image a number of tunnels including the Fujikawa and Kanaya tunnels in a combination of methods to map structural features along the alignment.

Jan 1, 2001

By Richard Seal

Nabarlek is situated in the Arnhem Land Aboriginal Reserve about 270 km due east of Darwin in the Northern Territory of Australia. During the dry season (May to November) Nabarlek is accessible from Darwin over the Arnhem Highway-- a distance of 330 km. Throughout the wet season (December to April), except for a few days, access is provided by aircraft from Darwin to the Nabarlek airstrip. Because of the limited access during the wet season, reagents and supplies have to be stock- piled for six months on the site to maintain operations. With the mine and plant being remotely located on private Arnhem land with very limited access outside the site fence, operating personnel are flown to Darwin every six days for their days off.

Jan 1, 1980

By M. Argiantopoulou

In today?s mining environment, improving production, performance, productivity and profitability is crucial. Production, ancillary, plant and shipping equipment need to be monitored and controlled by online systems delivering production statistics and real-time information to everyone involved, including equipment operators. Traditional systems currently in use today, operate in an iterative mode constantly switching between scheduling and execution. However, the real world tends to change in ways that invalidate such advance schedules. Agent based computing has been hailed as the most significant breakthrough in software development and the new revolution in software. Agent systems are being used in an increasingly wide variety of applications, including complex mission critical systems such as Air Traffic Control. This paper presents the possible ways that multi-agent systems can be applied to mine production and rehabilitation scheduling problems with focus on real time fleet management, plant and equipment performance monitoring, downtime and delay reporting, stockpile management, personnel and equipment tracking and product distribution and transportation.

Jan 1, 2006

By Jim Gebhardt

Douglas W. Fuerstenau (DWF) grew up on a farm and in several small communities in rural South Dakota during the depression years, where he learned the value of hard work. Working hard can produce results but being clever and hardworking will give you a bright future. In his later school years, Fuerstenau’s family moved to Rapid City where his intellectual curiosity and capacity helped him graduate with a B.S. in Metallurgical Engineering from the South Dakota School of Mines and Technology in 1949. His technical interests led to graduate studies and completion of a master’s degree from the Montana School of Mines in 1950 and Sc.D. degree from the Massachusetts Institute of Technology (MIT) in 1953.

By H. Janas

In a gas/coal outburst the gas plays an active, driving part. The proneness of coal to outbursts can be determined by means of its gas emission properties, since coal that is liable to outbursts differs from coal with normal gas emission properties in that it liberates its gas from the sorptive bond more quickly. There is a risk of outburst when the flow of metha¬ne originally desorbed by the coal is sufficient to move the loosened coal which has been broken suddenly. The violence of a gas/coal outburst can be evaluated from the distance of projection of the mass of coal. It depends on the gas pressure and on the liability to outburst of the coal at the original centre of the outburst. Both factors are complementary in their effects so that the same work is done in a gas/coal outburst when there is a high gas pressure and low proneness to outburst as when there is a low gas pressure and a higher proneness to outburst. The gas pressure in the coal increases with its gas content. Consequently it is possible to deduce the gas pressure of a coal seam from its gas content. In the Federal Republic of Germany the risk of a gas/coal outburst is thought to exist when the desorbable gas content of the coal reaches or exceeds the value of 9 m3/ton and if the specific limit value of the proneness to outburst is exeeded. The Mine Ventilation Testing Station of the Westfalische Berggewerkschaftskasse has developed a new method for determining the risk of gas outbursts immediately after taking the samples at the coal face (1), (2).

Jan 1, 1980

By H. Boyd

Fluid energy grinding, or jet pulverization, refers to the process of entraining solid particles in high velocity gaseous or vaporous streams and reducing their size by impact and attrition against other particles or some sort of target. Since all desired size reduction is not achieved in one pass through the zone where energy is applied, some form of classification is necessary to return oversize particles to the grinding zone for further size reduction. Applications Fluid energy mills have normally been used to produce products where the particle size is basically finer than 325 mesh. Products having particle size distributions with a maximum size of 4 or 5 µm, and with a high percentage finer than I µm, can be produced using fluid energy mills. More recently, some fluid energy grinding units have been applied economically to produce ground products with 1 or 2% coarser than 200 mesh. It is also possible to consider usage of a jet-pulverizing zone, without the usual integrated air classi¬fier, operated either in open circuit or in conjunction with a screen. Feed sizes to be delivered to the fluid energy mill depend on the material involved, the type of jet pulverizer used, the finished product size requirement, and the upstream process. In some units feed sizes up to l in. or larger can be accepted, but practical economics usually require the starting material to be -4 mesh or smaller and some pulverizers are typically fed at 20 mesh top size. It is not unusual to find feed materials at essentially -325 mesh when extremely fine products are needed, since capacities are improved with finer feeds. Conventionally the fluid energy grinding process has been used for relatively soft and nonabrasive materials. This includes very low¬melting-point and temperature-sensitive materials or coatings, since there is no measurable temperature rise during fluid energy milling. More recently, however, jet pulverizers are being used on highly abra¬sive materials such as silica, feldspar, glass, zircon, calcined alumina, coke, boron carbide, and similar materials. Since the primary energy application is by impact of particles against themselves, there is a low rate of wear resulting in a small amount of product contamination and in low maintenance costs. Usually the fluid energy pulverizer produces a more narrow particle size distribution than other mills provide, and this is useful where such a requirement exists. It is possible, within limits, to adjust classifi¬cation and other functions of the overall fluid energy system to vary the particle size distribution curve and thereby approach the broader distribution obtained from other grinding methods. By controlling the temperature, composition, and humidity of the fluid used, it is possible to incorporate other functions with the size-reduction process. These include drying or adding moisture, coating, mixing and blend¬ing, and even oxidation or reduction and other chemical reactions or their inhibition. The finished product is discharged in the fluid stream and is conveyed pneumatically to the desired point, where a suitable dust collector must be provided. Operation and Mechanical Features One of the earliest fluid energy mills is the Micronizer now manu¬factured by the Sturtevant Mill Co. Similar units are also manufac¬tured by Jet Pulverizer Co. and others. As shown in Fig. 81, the micronizer consists of a shallow circular grinding chamber with noz¬zles arranged at the outer periphery to discharge tangentially inward. Fluid (usually compressed air or superheated steam) is provided to the nozzles from a manifold at pressures normally in the range of 100-150 psig and at temperatures up to 800°F or higher, depending on the raw material, required results, and economic factors. The com¬pressible fluid expands to high velocity through the nozzles and gener¬ates a spiral flow pattern in the grinding chamber, and discharges

Jan 1, 1985

By J. W. Powell

Several years prior to 1962, it became obvious that in order to develop ore reserves below the Storke Level, it would be necessary to devise a method to facilitate the ore being lifted three hundred feet to the surface or six hundred feet to the mill. The final plans called for an underground crusher complex with two stages of crushing and a conveyor belt gallery for transport of the ore six hundred feet above, to the third crushing stage. Access into the area was gained in 1962, by sinking Five Shaft approximately one quarter mile southwest of the proposed complex site, and drifting into the area. Collar elevation of Five Shaft is three hundred feet above the 600 Level Crusher Complex. All muck was loaded into ten-ton granby cars, hoisted to the surface and dumped. (See Figure 1 for the relationship between Five Shaft and the Crusher Area) Drifting into the Crusher Area contunued until 1965 at which time the Crusher Room Cutout was started. The Crusher Access Drift (CAD on Figure 2) war driven and mining pm- ceeded according to the description on drawings marked Figure 3a and 3b. After the arch portion of the Cutout was excavated and concreted, removal of the center "pillar" commenced. This muck was removed with an Eimco 123C crawler-mounted front-end loader. (See Figure 4) A total of 576,000 cubic feet of rock was removed from the Crusher Cutout. All sup- port was afforded by grouted roofbolts on a specified pattern, as shown in Figure 3c. Crane support columns were put into place and held by braces welded to roofbolt heads. Sidewalls and endwalls were formed and concreted. (See Figure 5 for the finished product)

Jan 1, 1970

By ERIK CHARRIER, ADITYA JUGANDA, Jürgen Brune, Gregory Bogin, Patrick Maier

Confined explosions are a major risk in underground coal mine operations. Depending on confinement, ignition location and obstacles in the flame path, methane explosions can transition to detonations. This research focuses on explosion experiments in a reactor with diameter of 71 cm and length of 30.5 m, along with developing the corresponding computational fluid dynamics (CFD) model that captures the observed flame behavior. The results show that the 2D and 3D CFD models are able predict the experimental flame front propagation velocity, but the 3D model shows more explicit conformity than the 2D model.

May 1, 2024

By G. A. Rosario, G. Peach

Twin 8.5 m diameter, 10 km long headrace tunnels under overburdens of up to 1870 m were excavated for the neelum jhelum hydroelectric project in north-eastern pakistan using two main beam gripper tunnel boring machines (tbms). Rock bursts were encountered and presented a significant danger to personnel and equipment. Micro seismic monitoring was installed to analyze rock burst characteristics and to create a database for future reference. Correlation of rock burst characteristics improved the ability to predict the likelihood, location, severity, and number of rock burst events. This paper presents the analysis of the micro seismic data

Dec 1, 2022

By John Frostiak, Don Welch, David Landriault

The use of paste technology for underground cemented backfill is widely accepted in the mining industry today as a potentially cost effective alternative to cemented rock and hydraulic slurry fill. While paste backfill is not the appropriate backfilling method for all mines, there are presently 23 operating tailings paste backfill plants throughout the world. This new technology has gained increasing acceptance as a backfill method over the last decade and its use is now expanding into the surface disposal of tailings using the stacked, thickened tailings disposal concept. Over the next 18 months there will be ten new paste plants commissioned in the world. Five of these ten plants will be used exclusively for surface tailings disposal or a combination of surface disposal and underground backfill production. The thickened tailings disposal concept, developed by Dr. Eli Robinsky in the early 1970's, has been in use for decades at several mine sites throughout the world (Kidd Creek Mine site in Northern Ontario), but always utilizing non segregating high density tailings slurry central discharge, stacked tailings placement. With the use of a higher solids content paste, the typical 2-degree beach angle can be increased to ten degrees or more with no runoff water and minimal shrinkage crack development through desiccation. This paper presents the design of the first mine to implement true surface paste disposal, Barrick Gold Corp's Bulyanhulu Mine in Tanzania. The paste system will be commissioned in the first quarter of 2001 allowing performance data to be collected to define the full potential of paste technology for surface tailings disposal.

Jan 1, 2001

By A. V. Glembotsky, N. A. Greshnova, V. P. Seregin, V. A. Glinkin

Based on a new alternative depressant of zinc sulphide - dimethyldithiocarbamate- modern technology has been developed for the treatment of complex polymetallic ores. In addition to its general function (depression of sphalerite and iron sulphides to some extent), this double-acting reagent is a promoter for galena and silver minerals. Laboratory and plant tests, as well as industrial experience have all shown consistently higher silver recovery to the lead concentrate as compared with sodium cyanide, resulting in less pollution and a safer environment

Jan 1, 1995

By H. A. DeMirjian

Oil production rate and ultimate primary recovery from a heavy or viscous oil reservoir is usually limited to a very small fraction of the original oil in place. Typically, normal production rate is in the range of up to 10 barrels per day and expected ultimate cumulative production is up to 10% of in place values. Heavy oil reserves are not all alike. The physical properties of the rock, the liquid hydrocarbons, and depths of the deposits are so different that each reservoir poses a unique enhanced oil recovery problem. In some reservoirs thermal recovery by internal heat generation or external heat injection has been successfully exploited. In other reservoirs, mining the oil bearing formation for oil recovery by surface processing has been practiced. This paper will present an overview of the heavy oil recovery state of the art and discuss the critical factors leading to the decision for selection of a conventional hydrocarbon recovery or mining and extraction processes.

Jan 1, 1978

By Arnolfo A. Valdivia

Prior to 1971, there were several clinical trials to evaluate programs for early detection of lung cancer. Among these, the Philadelphia Pulmonary Neoplasm Research Project,(3) the Veterans Administration Study published by Lilienfeld,(7) and the controlled trial of the Kaiser Foundation Health Plan showed an overall five year survival rate of 8% for newly detected cases (the same as the national statistic for unscreened patients). In 1971, the National Cancer Institute initiated three randomized, controlled mortality studies using lung cancer screening of persons at high risk (male smokers over 45 years old). The studies are being conducted at the Johns Hopkins University Hospital, the Mayo Clinic, and the Memorial Sloan-Kettering Cancer Center. The studies have slightly different designs in the combination of sputum cytology and chest x-rays. At the Mayo Clinic the study group is offered screening with sputum cytology and chest x-rays every four months, whereas the control group is advised to have an x-ray and cytology every year. No reminders are sent, and it is believed that only about 20% of the control group is screened. At Johns Hopkins and Memorial, both experimental and control groups are offered annual chest x-rays. The experimental group is additionally offered sputum cytology every four months.(5) At present all of the programs show that screening can detect cancers that are undetectible by other means. However, at this time mortality rates in the control and experimental groups are not significantly different in any of the three studies. OUR PROGRAM Our clinic is located in Grants, New Mexico and we provide most of the pre-employment physical examinations for the mines operating in the Grants area (Kerr McGee Nuclear, Homestake Mining, United Nuclear, Western Nuclear, and Ranchers). In the examinations, we obtain the previous mining history of the worker, a chest x-ray, a sample of sputum for cytological examination, and a blood sample. We also provide routine annual physical examinations of the workers, with special interest in the detection of bronchogenic carcinoma. In the early seventies, we did not have a definite surveillance program. We did not know whether we should have a program like the one started at Memorial or like the one started at the Mayo Clinic. After long consideration, we decided to have a program that does not demand a sputum cytology and chest x-ray every four months, but that allows as many chest x-rays and sputum cytologies as needed to diagnose lung cancer as early as possible. We believe that, if a screening method for cancer is to be optimally effective, it must detect the process at stages early enough for curative therapy. We order a test depending on the age of the miner, the race, the mining history, the smoking history, the radiation exposure levels, and the results of the previous chest x-ray and sputum cytology. With the help of the computer, we have a list of all the miners who should be watched closely because of age, race, mining history, smoking history, radiation exposure, etc. Examination of the miners is performed at our clinic, where all the records are kept. The sputum is collected there but examined in Grand Junction, Colorado, by Dr. Geno Saccomanno. There are two ways to collect sputum. The best way is to collect three consecutive morning samples. For this, we need the cooperation of the miners. They have to follow these instructions and mail the bottle containing the sample to Grand Junction. "Instructions for obtaining a good cough specimen" The enclosed plastic bottle contains a preservative solution, so do not empty out the liquid in it. When you go to bed, place the plastic bottle at your bedside where it will be handy in the morning. When you first get up in the morning (before breakfast) try to cough up some "phlegm" from deep in your chest, and spit it into the liquid in the bottle. Try coughing several times. If you have difficulty coughing, try inhaling deeply the steam from a teakettle (or home-type inhalator). Keep the amount of saliva (ordinary spit) that you put into the bottle along with the cough specimen as small as possible. Do not collect the "phlegm" or mucous that comes from the back of your nose. Put the cap back on the bottle, and shake it vigorously for two minutes. If the amount of material you have coughed up is quite small, then keep the bottle at your bedside for three or four days, and each morning try to add another cough specimen. After obtaining your cough specimen, repack the bottle in the mailing container, and attach the enclosed mailing label. It does not require any postage stamps. Unfortunately, some miners "forget" to mail the sample and end up with an incomplete physical examination. To avoid this some companies, like Homestake, request that we obtain the sample in our clinic by forcing cough and expectorant with a nebulizer machine. This method does not give as good a sputum sample as the previous one, but we do get a sputum sample for every miner. The policies of different companies, in regard to annual physical examinations are different. All

Jan 1, 1981