Search Documents

By H. B. Charmbury

In the United States and in Pennsylvania in particular the coal mine drainage problem is of continuing and growing interest to the coal mining industry, the state government, the federal government and the public at large. The 1965 amendments to Pennsylvania's Clean Streams Law prohibit the discharge of acid mine drainage into the streams of the Commonwealth after January 1, 1967. Because of this new legislation, the coal mining industry and state government are extremely aware of the necessity for new techniques for treatment and prevention of the flow of acid mine drainage from the active mines of the Commonwealth in order to keep the coal mining industry in business in Pennsylvania. Approximately one-third of the total volume of mine drainage presently polluting the streams of the Commonwealth originates from "active" coal operations and two-thirds comes from "abandoned" mine discharges. As early as 1963 it became evident that the Commonwealth of Pennsylvania and the coal industry in Pennsylvania would have to take active steps to abate the mine drainage pollution of Pennsylvania's streams and rivers. This became quite clear during the deliberations in Harrisburg which climaxed a twenty year struggle for effective strip mining legislation. The bituminous strip mining law enacted that year made it unlawful to have any acid discharge from active stripping operations.

Jan 1, 1968

By Louis A. Panek

INTRODUCTION Block caving is distinguished from other types of mining in its requirements that the mineral body to be extracted must cave after a relatively large tabular open¬ing is created underneath it, and that the caving must be predictable and controllable for both operating and safety reasons. A mineral body that caves readily may present special problems with respect to ground support in the mining access openings, where stability, rather than failure, is the desired objective. The complete ex¬traction of a caving block, which may measure 50 to 100 m on a side and 100 to 300 m in height, tends to create a large void, resulting in significant changes in the ground stress system and a migration of rock from all directions toward the void; these events begin very early in the life of the mine and lead to additional spe¬cial problems with respect to control of ground move¬ments in the mine working areas, in the rock adjacent to the caving stope, and on the subsiding surface above the mine. Thus, the mechanics of an undercut-cave operation involve a broad range of geotechnical subject matter, including the determination of the lithostatic earth stresses, the structural properties of a large jointed rock mass, the flow properties of the fragments after caving, the stability of tunnel-like openings, and the stability and displacements of the rock structure (1 to 2 km in size) that surrounds the ore body. The objectives are achieved by in-place measurement of rock properties, laboratory tests, theoretical structural analyses of the related prob¬lems, measurements of structural behavior in and above the mine, and comparison of theoretical predictions with actual performance in order to interpret and refine the predictive capability. Undercut-cave mining (Julin, et al., 1973) differs from most other methods in that the caving is an essen¬tial and inherent part of the excavation process and in¬volves the movements of millions of cubic meters of rock over distances of hundreds of meters, as compared to the gradual 2-m settling of the overburden typical of full¬caving longwall coal mining. Undercut-cave mining may involve a rock mass on the scale of a 1-km diam open¬pit mine, but mining is several times deeper than that in the open-pit mine; furthermore, a large portion of the rock mass is in a failed, rather than a stable, state. Ground-control problems are inevitable in a situa¬tion where ground movements are occurring on such a large scale, and where the rock mass is expected con¬veniently to cave at one location but to be stable at an¬other. To devise effective responses to these ground¬control problems, one needs to know first of all what is happening, not merely at the point where the symptoms are observed, but more broadly with respect to the be¬havior of the entire mine rock-mass structure over the total area of extraction, including the effects on the sur¬face as well as those underground. Monitoring structural behavior on this scale would require a sizable group of people, if they attempted to measure all the significant mining-induced changes of ground displacement and pressure, even on a 100-m grid of points. The practical approach is to conduct the mea¬surements activity by a judicious sampling, making in¬termittent, concentrated efforts in selected areas of lim¬ited extent to study problems of immediate importance; simultaneously a minimum level of surveillance is main¬tained over the total structure to delineate long-term be¬havior trends in the major structure, which provide the baseline reference data that are so essential for interpre¬tive purposes. Mine-structure behavior depends not only on the mine extraction configuration and sequence, but on the rock structural properties and how they change from one location to another in the mine. Increasing attention is being given to determinations of rock strength and de¬formation by performing mechanical properties tests in place and in the laboratory, and by drawing inferences from the mapping of geologic structure in mine openings as they are driven and from the logging of cores ob¬tained from exploration drilling that may be performed primarily for delineating ore reserves. Monitoring of mine-structure behavior and inter¬preting it in terms of the growing excavations and the structural properties of the rocks have significant im¬pacts on designing the major undercut-cave operations of undercutting and drawing the ore, supporting the ac¬cess openings, and controlling surface subsidence. The purpose of this chapter is to call attention to the com¬mon ground-control problems encountered in undercut¬cave mining, to relate them to the mining process, and to explain the geomechanical approaches to analyzing these problems with emphasis on methods that are most readily available to the mine staff. UNDERCUTTING, CAVING, AND DRAWING A distinguishing characteristic of an undercut-caving method of extraction is the objective that the rock mass fails of its own weight in a predictable and controllable manner, after it is undercut by excavating a tabular¬shaped void, horizontal or inclined. Induced or forced caving refers to procedures that may be resorted to when the ore will not self-cave over the desired span. Block caving, panel caving, and mass caving are terms used to denote the particular sequence of undercutting and ex¬tracting the total area of the ore body on a single min¬ing level. The discussion herein is not specialized to any of these variations; the word block as used does not imply anything as to sequence. CREATING THE UNDERCUT A common undercutting method is to drive a series of drifts and blast the intervening pillars. Theoretical structural analysis and practical experience show that ground-support problems in the undercutting drifts and in underlying access openings as well (the same princi¬ple applies even if undercutting is done by belling out drawpoints from the slusher drifts) are minimized by retreat-mining across the undercut slot according to a sequence such that the growing undercut area retains a

Jan 1, 1982

By D. R. McGregor, B. V. Clingan

A practical application of recent design concepts makes it possible to design a column cell to fit a specific set of conditions. The design and operating parameters of a column cell installation that replaced a conventional two-stage copper flotation cleaning circuit at Magma Copper Co., San Manuel, AZ, using these design concepts is described. A survey of other mineral processors using column cell technology was conducted. The results of this survey are also discussed.

Jan 1, 1988

By Jan K. Wolski

Detection of the air recirculation branches within a large ventilation network may be difficult, therefore a PC computer routine has been developed to perform this task in an efficient and reliable manner. This paper describes the method illustrated using a network with complex multi-recirculation circuits. The fact that only the air flow directions and not the flow rates are used in calculations is of some interest. The air recirculation during a real mine fire is demonstrated using the PCVENT program, whose version 4.0 includes current information about any recirculation branches during network calculations or during a fire simulation. This paper also discusses some transient problems related to air recirculation, and gives examples.

Jan 1, 1993

By Jay F. Colinet

Coal workers’ pneumoconiosis (CWP), commonly known as black lung, is caused by the inhalation of respirable coal mine dust and is a disabling and potentially fatal lung disease with no cure. Historically, CWP has taken a tremendous human and financial toll on the U.S. coal mining industry. Recent health surveillance data indicate that CWP continues to occur at elevated levels. Respirable coal dust exposure must be controlled to prevent the development of CWP. The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) conducts laboratory and mine-site research to identify control technologies that can be used to successfully reduce respirable dust levels. Various technologies, using multiple methods of control, can be applied to reduce dust levels. An overview of CWP’s impact and a general methodology for controlling respirable dust in underground coal mines are discussed in this paper.

By John A. Lombardi

The solutions used in the heap biooxidative treatment of sulfidic refractory Au ores and concentrates generally load free mineral acid and metals and, in time, become bacteria activity inhibiting due to increased acid and/or metals concentrations. The metals­acid loaded, bacteria action inhibiting, solution must then be: (a) processed, prior to re-use, to reduce its metals and/or free acid mineral acid components to bacteria activity compatible levels; or (b) neutralized prior to discharge. The most common solution processing method to adjust acid-metals contents is liming to effect the precipitation of dissolved metals and neutralization of acid sufficient for solution discharge or re-use. The lime treated solution is high in suspended, colloidal precipitates and requires clarification before reuse. Most often the "bleedstream" of biooxidation solution that is lime treated is discharged and req­uisite volumes of fresh water added to the process inventory. Depending on the level of bacterial action in a heap and the acid consumption characteristics of the ore/concentrate being biooxi­dized, the bleedstream taken from the circulating, irrigation on­off, solution, can be large (e.g., 10%-20% and sometimes as much as 50% of the daily solution flow requires treatment-dis­charge). The lime charge for bleedstream treatment is commen­surately large and represents a major operating cost of the bioox­idation process. The patented HW Process Technologies (HWPT) Engineered Membrane Separation (EMS™) method is an alternative biooxi­dation bleedstream treatment method. EMS™ processing removes the multivalent base metals ions in an acid solution to a small volume EMS™ "concentrate" (typically 25% of the feed­stream volume). The EMS™ method coincidentally makes a "clean acid" EMS™ "permeate" (typically 75% of the feed­stream volume). In general, EMSTM processing enables 75% of the bleedstream volume to be recycled; allows up to 2/3 of the bleedstream acid to be recovered as a 10% solution; and delivers dissolved metals in a highly concentrated stream suited to a. metals recovery or b. reduced cost lime neutralization for a given metals precip­itation relative to full bleedstream neutralization (typically a 30% lime use savings). Implicit in the recovery of process water for re-use and reduced reagent addition requirement for metals precipitation is a significant reduction in wastewater-sludge dis­posal facility size.

Jan 1, 1998

By Frank F. Aplan, Robert S. Thomson

A placer ore jig, typically used to recover fine gold, tin and diamonds from alluvial ores, has been modified to remove fine pyrite from minus 6.4 mm (-114 inch) coal. In parallel tests, it proved to be far superior to two conventional coal jigs, the Baum and the Baum-feldspar, in removing fine pyrite from coal. The Pan-Am placer jig was found to remove essentially all of the +28 mesh pyrite and from 99% to 90%, decreasingly, in the 28 to 200 mesh range. This jig also showed a superior performance to the Baum-Type jigs in removing fine coal from its associated refuse. The superiority of the Pan-Am placer jig is related to the strong emphasis given on the suction stroke and, hence, on consolidation trickling, whereas the Baum jigs principally emphasize the pulsion stroke during jigging.

Jan 1, 1995

By C. A. Wheeler

This paper presents the initial findings of a research program to reduce the annual equivalent costs of belt conveying systems. The work utilizes models to predict the motion resistance of belt conveyors that take into consideration the influence of key conveyor variables, such as idler roll diameter, spacing, troughing configuration and belt width. Given a specified conveyor configuration, the capital and ongoing costs of the system can then be approximated based on the required belt, idler rolls, structure, drives, etc. The research provides a computational means to rapidly analyze a large number of potential conveyor configurations and to compare each on an annual equivalent cost basis.

Jan 1, 2008

By Roland Heersink, Charles H. Wells

This paper discusses how a mill uses off-site data hosting approach to effectively utilize an entire suite of advanced applications to optimize daily operations, without incurring the overhead of on-site systems, staff and support. Details of the solution are provided, together with a live view of actual plant operations. Security and authentication mechanisms are also outlined so that users may gain an appreciation of the actual security of the remotely hosted data. A number of Web-hosted software applications provide direct connectivity to the database offering rapid and deterministic response times to clients. A 24x7 help-desk is available to authorized users from any Internet connected device. The paper shows how mill management advantageously use wireless PDA's to view what is going on at anytime and from anywhere. It concludes with a summary of how the approach is being used to speed decision-making and capture spot market opportunities.

Jan 1, 2002

By Hamed Khodadadi, Hamid Ghadiri

The ball mill grinding circuit has widespread application in mining, metallurgy, chemistry, pharmacy and research. It faces some challenges because a grinding circuit is a multivariable system in which high interaction between loops, variation of system parameters with time, and time delays are problems. In this study, a fuzzy logic self-tuning proportional–integral–derivative (FLST-PID) controller based on an improved disturbance observer is designed for control of ball mill grinding circuits. It is combined with an improved disturbance observer (IDOB) to eliminate system interaction, attenuate internal and external disturbances and compensate the effect of system uncertainty on the performance of the ball mill grinding circuit.

By L. Yuan, J. H. Rowland, R. A. Thomas

Hydrogen (H2 ) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system. In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, H2 concentrations in the airflow are constant, while in the full-scale experiments, increasing H2 concentrations generated as a byproduct of charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to safeguard underground miners.

Surface characterization techniques, i.e. contact angle measurement, atomic force microscopy (AFM) surface force and surface imaging measurement, were applied to investigate the molybdenite surface in aqueous solution. It was shown that the cleaved basal surface of molybdenite was very hydrophobic with a 92 degree water contact angle. The non-polar component of the solid surface free energy is 50.52 mJ/m2 while the polar components are almost zero. The solid surface was not reactive and was only weakly charged at the pH 6. When the aqueous media changes from water to 1×10-4 M KEX solution, the measured contact angle, adhesion force and surface roughness all increase slightly. However, ethanol rinsing made the surface change back to the bare substrate. It was suggested that the hydrophobic chemical, i.e. dixanthogen, which was shown in the morphology of patches by the AFM image, physically adsorbed on the hydrophobic molybdenite surface through the hydrophobic interaction.

Jan 1, 2009

By William T. Griswold

Few metals or industrial minerals can boast a better growth record over the past fifteen years than the borates. This period of growth occurred before the influence of any large-scale use in plastics or high-energy fuels. These new developments not only provide expanding markets, but the programs related to their development are generating research information that will lead to many other new uses. The most dynamic growth areas for refined products of boron or borates are in the acid, the oxide and the reduced forms, such as the metal and the hydrides. Expanding requirements for these products will modify the emphasis on the use of naturally occurring sodium borates. Any borate from which boron can be economically extracted will become a potentially important ore. This is particularly true of the calcium borate, colemanite. Only one large deposit in the Western World has ever been developed where the principal economic minerals are sodium borates, This factor alone would discourage any exploration program directed solely toward the discovery of these ores; on the other hand, ample exploration opportunities for calcium borates exist in the desert regions of California and Nevada. It is therefore reasonable to restrict a program to this region, in spite of geologically favorable areas in foreign countries such as Turkey, Argentina and Chile.

Jan 1, 1959

By B. M. Davis

The problem of assessing uncertainty in grade estimates has been a topic of research and debate since kriging was first introduced. Use of the kriging variance was originally touted as all that was necessary in order to produce confidence limits for grade estimates. Since then the prudence of using the kriging variance for confidence interval estimation has been questioned, and techniques such as the jackknife and conditional simulation have been proposed to develop "true" interval estimates. This paper compares the differences between interval estimates produced by the three methods and makes conclusions about the performance of confidence intervals produced by the different methods.

Jan 1, 1997

By Milan Yekich, Emanuele Cauda, Justin Patts, Cody Wolfe

This study presents the application of low-cost dust monitors (LCDMs) for real-time monitoring of respirable dust in a mining environment. LCDMs significantly enhance data collection by providing continuous, granular and cost-effective dust concentration readings. This case study demonstrates that by deploying LCDMs, mining operators can respond quickly to changes in dust levels, improving occupational safety and air quality management. The results show how such monitoring technologies can be integrated into routine operations to reduce dust exposure and prevent health hazards such as silicosis, especially when coupled with appropriate mitigation strategies.

Nov 1, 2024

By Lok W. Home

INTRODUCTION Today, raise drilling (boring) has become the stan¬dard method of raising throughout the Western world. It is estimated that the majority of raise footage com¬pleted in 1977 was accomplished by the raise drilling method. Extensive replacement of the drill and shoot system by mechanized raise drilling has occurred be¬cause users have recognized one or more of the follow¬ing advantages. In a direct cost per meter comparison, mechanized raise drilling is economically more attractive than drilling and shooting. Mechanized raise drilling offers improved personnel safety over the drilling and shooting method. Mechanized raise drilling is a faster and more predictable method for excavation than is drilling and shooting. The raise cost per unit of length becomes less as the raise length increases, offering greater flexibility in the overall design of mines. Mechanized raise drilling provides a substantial reduction in labor requirements. 6) Mechanized raise drilling improves the working environment. 7) Mechanized raise drilling improves the rock in¬tegrity of round, unblasted raises. Increasing acceptance of the raise drilling technique is enhanced by continuing equipment development. Today, a wide range of machines and capabilities is available, machine drive systems have been improved, reliability has been increased, and cutter technology is being improved quite rapidly. Table 1 lists the four major manufacturers of raise drilling machines, cutters, and reamers, together with the approximate number of machines that each company had in operation at the end of 1977. Although Reed and Smith are major suppliers of reamers and cutters, they do not manufacture the drilling machines. Four or five other relatively minor suppliers have built machines, reamers, and cutters for raise drilling, but they did not have a substantial num¬ber of machines in the field at the end of 1977. MACHINES FOR MECHANIZED RAISE DRILLING There are three principal arrangements for making machine-bored raises. They include the use of standard raise drills, reversible raise drills, and blind-hole or box¬hole raise drills. Standard Raise Drills The standard raise drilling machine is set up on one mine level or on the surface, and a pilot hole is drilled from that level or surface to a level below. When the pilot hole has been drilled, the raise then is reamed back from the lower level to the upper level or the surface. This arrangement is illustrated in Fig. 1. Reversible Raise Drills The reversible raise drilling machine is set up on a lower level of the mine, and a pilot hole is drilled up¬ward to a higher level. The raise then is reamed back from the upper level to the lower level. This arrange¬ment is illustrated in Fig. 2. The machines used for this type of raise drilling normally are capable of being used as standard raise drills. Blind-Hole or Boxhole Raise Drills The blind-hole or boxhole raise drilling machine is set up on a lower level of the mine, and a full diameter raise is bored to a higher level without the use of a pilot hole. This type of machine is illustrated in Fig. 3. Drill Recommendations If access to upper and lower mine levels is equal, the standard raise drill should be used. The complexity of the equipment and associated handling procedures for boxhole drilling far outweigh any mechanical advantage or reduction in the number of operations, provided that access to an upper level is available. If there is good access to a lower level but only limited access to an upper level, the use of a reversible raise drill should be considered. If there is no access to an upper level, a blind-hole or boxhole raise drill is the only practical mechanized system. MACHINE SELECTION There are six major considerations in selecting a machine for raise drilling. These include operating range, cutter loading, machine structure and main¬tenance, drill string configuration, drive system, and automated controls. Operating Range As shown in Table 2 and Figs. 4 through 6, raise drilling machines are available for a wide range of hole sizes. Standard raise drill ratings range from raises of 0.9 m (3 ft) diam and 120 m (400 ft) length up to raises of 3.5 m (12 ft) diam and 900 m (3000 ft) length. Boxhole raise drilling machines are available for raises ranging from 0.9 m (3 ft) to 2 m (6 ft) diam with lengths up to 90 m (300 ft). Table 2 lists, among other criteria, the torque and thrust of typical machines; torque and thrust are the main criteria for analyzing the capacity of a machine. The raise sizes shown in Table 2 assume a condition of medium hard to hard rock formations and optimum cutter loading. The recommended raise size for a given machine can be exceeded when raising softer rock formations or when the operator is willing to accept a lower level of performance; the performance is related directly to the 1093

Jan 1, 1982

By H. Lyn Bourne

This is the 12th year for this column and the 11th in which the royalty data have been tabulated. This year adds 20 to 30 new entries. There are, however, some deficiencies that the readership hopefully will fill. The most common mineral commodity is construction aggregates - either sand and gravel or crushed stone. There are several states where no royalty information was available for either commodity. Readers can help share information about these missing states, so next year there will be fewer states without information. Severn Brown again sent helpful information from the Prospectors and Developers Association of Canada (PDAC). The summer 1992 issue of PDAC Digest recommended"... the most useful technical paper ever published for economic geologists...." "Net smelter return models and their use in the exploration, evaluation and exploitation of polymetallic deposits" was written by R. Goldie and P. Tredger (Geoscience Canada, Vol. 18, No. 4, pp. 159-171). Last year's column described leasing practices in Russia. Some new information has been gathered since then. Kirill Kavun is the managing director of the International Geoeconomic Center in Moscow. He sent two publications from 1992-"Regulation on the procedure of licensing the use of the subsurface," and "Law of the Russian federation on the subsurface." Both are supplements to the magazine Mineral Re¬sources of Russia, Economics and Management.

Jan 1, 1993

By John W. Carson, David S. Dick

The last few years have produced new methods of characterizing flow properties of bulk solids. Abrasive wear and particle attrition can now be accurately measured in a laboratory and scaled up to field condi¬tions. In addition, the effect of large par¬ticles on a material's flow properties (cohe¬sive strength, bulk density, wall friction) can be determined as well as the effects of var¬ious additives such as freeze conditioning agents. New developments have occurred with devices to improve the reliability of solids flow. Much attention has been paid to find¬ing ways, by using inserts, to provide a mass flow pattern with relatively shallow hopper walls. Such devices can also provide reli¬able in-bin gravity blending of bulk solids or completely nonsegregated discharge. Other developments have occurred in the area of belt-to-belt transfer chutes and sealing screws. The technology and hardware for running bench scale flow tests on bulk solids samples and transforming the results into reliable designs has been in existence for nearly 30 years (Jenike, 1964; Marinelli and Carson, 1986). It has been shown repeatedly that reliable materials handling systems can be designed to avoid the problems of no-flow due to arching or rat-holing, erratic flow, segregation, loss of capacity, or spontaneous combustion. Running flow properties tests and carefully designing a bulk handling system are not expensive, particularly when compared to downtime costs and continual flow problems. New developments in characterizing flow properties of bulk solids include: • a shear tester for measuring the properties of run-of-mine ores containing large par¬ticles; • attrition testers to simulate a wide range of flow conditions; • a tester to measure the wear rate of liners in bins, feeder parts, etc.; • a dustiness tester to measure the potential for dust and the effect of dust control meas¬ures; and • techniques for measuring the strength of frozen ores and the effect of freeze condi¬tioning agents. In the area of improving the flow of bulk solids, there are new techniques for ensuring reliable flow without using up excessive headroom. These include: • belt-to-belt transfer chutes to handle po¬tentially sticky, abrasive, and dusty ores; • designs for the interface between a bin/ hopper and apron or belt feeders to avoid hangups and minimize feeder loads; methods to feed solids reliably into a pres¬surized process; and designs for handling systems that will mini¬ mize attrition, avoid segregation, or auto¬matically blend materials together. Characterizing flow properties Large shear cell It has long been known that the cohesive strength of a bulk solid is due mainly to its fine fraction. However, the effect of the larger particles (that were assumed to re¬duce the strength) could not be measured. The development of larger scale (205 mm¬diam and 0.6 x 0.9 m or 8 in.-diam and 2 x 3 ft) shear testers has made it possible to measure the properties of a wider range of materials. Now cohesive strength measurements can be made with up to 100 mm (4 in.) particles. The results obtained from the large shear testers, together with the results of the nor¬mal shear tests on the fine fraction, are used in the design of reliable stockpile reclaim systems and crusher feed systems. A high percentage of large particles can reduce the measured shear strength of a bulk solid. However, segregation may alter the size distribution and should therefore be considered (Carson, Royal, and Goodwill, 1986). In addition, larger particles will

Jan 1, 1989

By Adam Bedell, Jack Raymer, Brad Crenshaw

Tunnel contracts often include provisions for pre-excavation probing and grouting for areas ahead of the tunnel heading. If grouting triggers are met, tunneling stops, and grouting is performed. There is substantial variation within the underground industry on what criteria are applied to the grout verification hole that is drilled post-grouting and before excavation resumes. The criteria for determination of the effectiveness should be dependent on the geology and local hydrogeologic conditions. The purpose of this paper is to present specific criteria that can be used by a practitioner to determine whether tunneling can resume or if additional grouting is required.

Dec 1, 2022

By Elmer R. Drevdahl

During the last few years there has been a rapid increase in the development of the community or junior college throughout the United States, Some factors behind this development include the need for more college facilities to service the growing number of high school graduates, the desire of the public to provide some post high school education at reasonable costs, and the need to provide post high school educational opportunities not now provided by most of the universities and colleges. Many of the new community colleges provide at least three educational services including local opportunity to provide the first two years of a four year college program, two year technical-vocational programs of a terminal nature, and adult educational opportunities. The community college has the advantage of not being saddled with years of academic tradition which prevent it from changing to suit the educational needs of the community It serves. The flexibility of the community college in developing new programs, particularly in the technical areas, is going to provide industry with many of the badly needed technicians it is now unable to secure.

Jan 1, 1965