Search Documents

By D. Hulse

Mineral resource classification is described in both the SME and CIM Standards for Mineral Resource Reporting. The CIM Standard states “… sampling … is sufficient to assume geological and grade or quality continuity between points of observation”, thus is a function of continuity and sample spacing. Continuity can be measured by use of a variogram model, but average sample spacing in three dimensions is more difficult to measure. The declustering algorithms provided with Geostatistics software, are commonly used to weight data for statistical analysis due to the sometimes-irregular spacing between drill holes during exploration. The weights are lower when data is closer, reflecting shared influence between samples, and higher for isolated samples reflecting independence. This paper will discuss the potential to use estimates of the declustering weight as an inverse relative measure for average sample spacing to gauge the confidence of the estimate independent of the single nearest sample. PROBLEM The classification of mineral resources and reserves has long been a combination of science, past experience of the estimator, judgment, and feeling. All of the definitions as presented in the standards of the various countries that participate in CRIRSCO are similar and deal with “sample points sufficiently closely spaced to support confidence in the continuity of …” This has been interpreted as the distance between the block estimated and the nearest sample (or samples). Geostatistics gave us the calculation of the estimation variance of the block, an implicit part of the calculation of weights in Kriging, to account for the confidence in the estimate. More recently, “Kriging Efficiency” has been used, however it is still dependent on the estimation error and responds in a similar fashion to the distance to the closest sample. It is also sensitive to the variogram nugget. Many of these methods result in very low distance/high confidence measures for blocks adjacent to a sample point with confidence decreasing (sometimes rapidly) as the distance to one nearest sample increases. This results in the “spotted dog” phenomenon where individual samples are surrounded by a higher classification near each sample decaying into pattern of decreasing confidence halos. In addition to the visual image of the spots, this raises the more practical problem of mine design when the classification changes between measured, indicated and inferred. This has led to ad hoc methods to classify material within the mining block so all of the stope receives that classification. These manual methods re both labor intensive and subjective. A popular technique is a multiple search method, where the estimator defines a minimum of number of samples from a minimum number of holes within a nested set of search distance that are used to classify estimates. These specified set of increasing distances are usually proportional to the variogram range. While this is generally a good technique and overcomes the spottiness of the closest sample or kriging error, it has certain issues including:

Jan 1, 2019

By Y. Wang, E. Forssberg, R. J. Pugh

The coagulation of dispersed ultrafine weakly-magnetic oxide mineral particles (e.g., natural hematite and chromite) in an external magnetic field can be described by interparticle forces. Essentially, coagulation occurs when the short-range London-van der Waals interactions and the long-range magnetic forces outweigh the stabilizing electrical double-layer repulsion. Using the classical colloid chemistry theory, the various components of the potential energy for different-sized particles at a series of ionic strengths and magnetic field intensities were calculated. The results of this theoretical analysis were then related to the results obtained from experimental studies in which the magnetic field-induced coagulation of the ultrafines of natural hematite and chromite in aqueous suspensions were investigated using a laboratory-scale electromagnetic solenoid. The experimental results relate the coagulation process (as determined by magneto-sedimentation analysis) to the particle size, the slurry pH and the external magnetic field. In the magnetic fields, the maximum coagulation occurred near the pH of zero-point-of-charge (pHzpc) of the minerals (where the electrostatic double layer repulsion was reduced to a minimum) enabling the particles to enter the "primary minimum" energy sink. On the other hand, in cases where the electrostatic repulsion was not suppressed, the long-range magnetic forces enabled coagulation to occur in the "secondary minimum." This caused the formation of chains that appeared to be relatively stable during sedimentation.

Jan 1, 1995

By Isobel Clark

The problem of the estimation of ore reserves is essentially a simple one to describe. Given a set of sample data, at specified locations within a deposit, how can we estimate the value (or quantity) of ore in unsampled areas. The question may be posed of a whole deposit (global) or it may be more desirable to estimate smaller volumes within the planned mine area, e.g. stopes or blocks (local). Many methods have been evolved to tackle this problem, from hand-contouring of values by the mine geologist to extremely sophisticated geomathematical analysis. The main difficulty with any estimation method in this context is that it is almost impossible to check whether the "predicted" value bears a close relationship with the "actual" value. The only reliable way to decide if an estimation method has "worked" is to test the eventual value of ore against the predicted value. This is, more often than not, impossible - even allowing for the time factor involved. To know the "actual" value of a mined block it has to be sampled intensely, and these values with their positions recorded accurately. Alternatively, blocks may be passed through the concentration process individually and these results recorded. In most producing mines neither of these alternatives are practicable or seen to be-important. Another problem with comparing in-situ (so-called) mineable reserves with production figures is the introduction of many variables into the concentration process -- dilution, wastage, possible stockpiling, mill recoveries and so on.

Jan 1, 1979

By Kirsten Corin, Belinda McFadzean, Cyril O’Connor, Jenny Wiese

As orebodies being mined globally are of ever-decreasing grades, the focus on the concentration process has moved increasingly to the challenges faced in management of the gangue minerals. This is especially so in the flotation of platinum group minerals (PGMs), where head grades are typically in the region of 4–7 g/t. Hence, in PGM operations, a typical recovery of about 80 percent requires depressing about 85 percent of the gangue minerals. In a flotation cell the main control parameters are reagent type and dosage, froth depth and air addition rate. This paper reviews research projects carried out over an extended period aimed at optimizing the depression of gangue minerals: both those that are naturally floatable and those, such as chromite, that are entrained.  This has involved comparing the two major depressants used in the industry — guar and carboxymethylcellulose (CMC) — in the depression of the relevant gangue minerals, as well as investigating their consequent effect on the behavior of the froth phase. Because most PGM flotation plants treat the ore as if all the PGMs are associated with sulfides, copper sulfate is widely used as an activator, but this can also lead to inadvertent activation of gangue minerals. Finally, chromite levels must be kept below 3–5 percent to avoid any negative effects on smelter performance, and thus it is important to reduce chromite recovery which mainly occurs due to entrainment through, for example, froth depth control.   

By W. R. Boehme

The test work was done in two parts. In Part I, five 6 x 16 mesh activated coconut shell carbon samples made by four different manufacturers were evaluated as to their gold loading rate and total gold loading. The five carbon samples tested are not identified by manufacturer and are simply designated as Types A through E. Then from the carbons tested, a suitable highly active carbon was selected for subsequent studies on impurity effects upon loading, Part II. Test Procedures The procedures and tests descriptions are given for the ultimate gold carbon loading tests and the dynamic gold carbon loading tests.

Jan 1, 1983

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

Manufacturers have improved various stirred mill types to be well adapted to fine and ultrafine grinding applications. These stirred mills, which are operated in wet or dry conditions, may be classified as horizontal — such as AHM-horizontal agitated media mill, IsaMill and Drais mill — or vertical — such as tower mill, Vertimill, Maxmill, Stirred Media Detritor and ATR vertical agitated media mill. The main difference between vertical and horizontal structures is in their operational variations. Additionally, the scaling-up of mills is also an important parameter for selecting the suitable orientation [1]. The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch-type stirred mill. The experimental results were evaluated using stress intensity analysis. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1 × 10−3 to 5 × 10−3 Nm at 750 and 1,500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value.

By Edmond O’Donovan

Mooranbah North is a new greenfield project in Australia's Bowen Basin that is projected to produce 4 mtpa of hard coking coal from a single longwall. Located in Central Queensland in Australia's northeast, this is one of Australia's main coal producing regions. From the outset, Mooranbah North's approach to equipment selection has differed markedly from that usually taken in the mining industry, and the conveyor industry in particular. Until recently, no performance requirements have been placed on conveyor equipment suppliers. This arose from a practice of purchasing components in an ad-hoc manner from a variety of sources, and the mine then configuring the system. More recently, single source supply has been adopted as a means of obtaining some performance guarantee, usually expressed in terms of system availability. Unfortunately, the term "availability" has a multitude of definitions, particularly in the underground coal sector. A conveyor availability of 98% is a common goal but this rarely means the conveyor must operate 165 hours/week, 52 weeks/year. There are mines that have one maintenance shift for each production shift and claim availability of 100%. What is meant is that no down time is logged to the conveyor during the hours that it is wanted. This "generous" definition of availability would not be tolerated in many industries and nor should it. Unfortunately, a true definition of availability, such as is applied to steam turbines in the power generation industry, is not particularly helpful. Five day/ week operations would immediately face a 28% penalty against 7 day rosters, and there would be no sensible manner in which weekend maintenance could be incorporated into the availability formula. The approach adopted by Mooranbah North was to specify a period of "Failure Free Operation," which would be followed by a maintenance period. This

Jan 1, 1998

By G. R. S. Smith

In any filtration, it is primarily the filter medium (cloth) and cake filtering properties that control the type of filtration equipment used and filtration conditions. The advent of new types of filter cloths, such as the membrane cloth discussed in this paper, can result in significant changes in filtration techniques and areas of application for filtration. For many suspensions, for instance, conventional filtration is uneconomic compared to gravity separation or not filtering at all (as with product recovery from dilute streams) because the solids are very fine, are hard to retain and build up filter pressure rapidly, and once retained are hard to remove. As a result of the developments discussed here, this is no longer the case. This technique and the use of the membrane filter cloth is well established. This filtration is currently being used for white liquor filtration in twenty-four mills worldwide in the chemical recovery step of the kraft process for producing paper pulp where it is replacing gravity thickeners in new plants. Filters up to 1000 sq. ft. (100 sq. meters) are filtering large volumes of solids from hot caustic solutions. The filtration materials and techniques discussed in this paper open the way to new methods and applications for filtration in the mining industry. It is not the intention of this paper to give a vigorous analysis of the different separations, but to outline some of the ways in which this filtration technique might be used in the mining industry.

Jan 1, 1989

By YUSONG MIAO, DI WU, XIANRONG YAN, YIPING ZHANG, JIE LIN, KEBIN LI

Rock fragmentation has been a concern in hard-rock mining for the mining industry. Rock fragmentation distribution is an important index to measure the blasting effect. It not only affects the cost of drilling and blasting, but also affects the efficiency of subsequent operations, such as loading, transportation and secondary crushing.

By LUIS ALBERTO TORRES-CRUZ

The Plewes method is relatively well known among geotechnical engineers interested in assessing the liquefaction potential of soil deposits. Furthermore, it was one of the four methods considered in the post-failure investigation report of the Feijao Dam I, also known as the Brumadinho Dam, in Brazil. The inclusion of the method in that report is likely to increase its visibility among geotechnical practitioners tasked with assessing the liquefaction potential of tailings. While the authors of the method duly presented it as a screening method, more recent technical literature contains conflicting views on its reliability. Considering the popularity of the method and that the safety record of tailings dams is a cause of great concern, this study assessed the uncertainty of results from the Plewes method. The study concludes that, even under optimistic assumptions, the results of the method are too uncertain for detailed characterization of tailings deposits.

By Jae-Chun Lee, Sadia Ilyas

"The present study was carried out to develop an economically feasible and environmentally friendly technique to extract metals such as Al, Fe, Cu, Zn and Ni from electronic scrap by employing Penicillium chrysogenum strain KBS3. Studies were carried out in various leaching modes, including one-step leaching with combined growth and leaching phases (Mode 1), two-step leaching with alternative growth and leaching phases (Mode 2), spent medium leaching with separated growth and leaching phases (Mode 3), leaching with fresh growth medium without fungal culture (Mode 4), leaching with deionized water (Mode 5) and leaching with commercial organic acids (Mode 6). The main lixiviants produced in leaching Mode 1 were citric, tartaric, oxalic and gluconic acids in concentrations of 12, 2.5, 1.8 and 152 mM, whereas in leaching Mode 2, the concentrations were 15, 0.5, 1.0 and 1,162 mM, respectively. In leaching Mode 3, 63 mM citric acid, 23 mM tartaric acid and 29 mM oxalic acid was observed. At 5% pulp density, both leaching Modes 1 and 2 showed similar metal extraction yields from the electronic scrap at 35º C. Approximately 96% Al, 98% Zn, 48% Cu, 25% Fe, 66% Pb and 73% Ni were extracted in leaching Mode 1 in 14 days. In leaching Mode 3, 85% Al, 81% Zn, 97% Cu, 22% Fe, 50% Pb and 63% Ni were extracted in 14 days. The extraction yield of Cu was much lower in leaching Modes 1 and 2 (48- 50%) than in leaching Mode 3 (97%), as well as in leaching Mode 6 (98%) with organic acids, including citric, tartaric, oxalic and gluconic acids.IntroductionTechnical innovations in electrical and electronic equipment with new functionalities and designs stimulate consumer purchasing and lead a rapid increase in the production of waste materials. Terazono et al. (2006) have reviewed the data on electronic waste generation in different parts of the world. Studies by Bertram et al. (2002) have also affirmed that waste electrical and electronic components are the fastest growing waste category, which emphasizes the need for efficient recycling strategies. The recycling of electronic waste is an important subject, not only from the perspective of waste treatment, but also from the perspective of the recovery of valuable materials. However, the recycling of electronic scrap is still limited, due to the heterogeneity of the materials present in the products (Veit et al., 2005).Bioleaching-based processes offer a number of advantages over conventional pyro or hydrometallurgical methods (Lee et al. 2007; Lee and Pandey, 2012). These advantages include simple, inexpensive (in some cases) and ecofriendly approaches and the generation of less active leach residue relative to other metallurgical processes. Although biohydrometallurgical processes have been successfully applied to the leaching of metals from ores (Olson et al., 2003; Rawlings, 2002), data pertaining to the application of these processes for the extraction of electronic scrap are still scarce. Recently, a few studies have been undertaken for the extraction of metals from electronic scrap/ printed circuit boards (Brandl et al., 2001; Faramarzi et al., 2004; Ilyas et al., 2007; Ilyas et al., 2010). These studies were conducted with mesophilic chemolithotrophic bacteria (Acidithiobacillus ferooxidans and Acidithiobacillus thiooxidans), cyanogenic bacteria (Chromobacterium violaceum) or moderate thermophilic bacteria (Sulfobacillus thermosulfidooxidans). However, compared to bacterial leaching, fungal leaching has several advantages, including (i) the ability to grow at a higher pH, thus making it more suitable for the bioleaching of alkaline solid waste; (ii) a generally faster leaching process with a shorter lag phase and (iii) the chelation of excreted metabolites (e.g., organic acids) with metal ions, thus reducing toxicity to the biomass (Burgstaller and Schinner, 1993; Aung and Ting, 2005)."

Jan 1, 2015

By Tevfik Güyagüler

Airborne dust is one of the important environmental problems in mines. Besides conventional dust control methods, recently, extensive studies have been carried out on the elimination of dust before it has actually been formed. Determining to what extend rock characteristics influence the amount of dust produced during different mining activities are considered as a guide for this purpose. The factors analyzed in this study were main mechanical, physical properties and petrographical constituents, namely free and combined silica. In the study regression analysis techniques were applied to investigate the effectiveness of aforementioned factors. INTRODUCTION Nearly every aspect of mining activity contributes to the air pollution caused by dust. Therefore the harmfull effect of airborne dust has been investigated many years and limit dust concentration levels were determined for various types of mine dust. To keep the dust level below limit value different dust control techniques have been applied in mines. So far, the well known techniques regarding dust control focuses on reducing the amount of airborne dust. However, recently various studies have been carried out to avoid the dust before it has actually been formed (Bhaskar and Gong, 1991). In this respect, influence of rock characteristics on dust formation is regarded as a guide for this purpose. The present contribution describes such a study in which the drilling operation is considered as the source of the dust. In this study drilling and dust sampling process were undertaken in a model gallery that simulates an underground working. The mechanical and physical properties of the rock samples were measured in rock mechanics and ore dressing laboratories. Quartz and combined silica contents of the rock samples, on the other hand, were determined in the laboratories of geological engineenring department. Rock samples used in the research were different types of coal measure rocks, namely, sandstone, shale and conglomerate. The rock characteristics studied in this work are brittleness, toughness, rock strength, hardness and hardgrove index as inherent properties; free silica, and total silica contents of rock samples as petrographical constituents. Although there have been various studies to determine the effect of rock characteristics on the dust formation, still the type and extend of effectiveness have not been understood clearly. LITERATURE REVIEW Most of the studies investigating the effect of rock properties on dust formation concluded that they are effective. In such an investigation, it has been found that inherent rock properties influence dust formation (Das, 1973). In the another study, dustiness of the air was considered as a function of the composition, hardness and moisture content (Panov, 1967). It was also accepted that in a drilling operation more fine dust is produced if the rock to be drilled is hard (Skochinsky and Kamarov, 1969). In some other investigations dust production were considered as a function of hardgrove index (Moore and Bise, 1984) or formulated in terms of brittleness, toughness and hardness (Güyagüler, 1991). The effect of the petrographical properties of coal or rock on dust formation characteristics have also been studied (Baafi, 1979) (Panov, 1967). Because of its importance, various researches were conducted the study to find out the effect of free and combined silica content of dust on dust formation. In one of the study, the relationship between quartz in the coal seam and quartz in the airborne coal dust was investigated (Ramani et al, 1988).

Jan 1, 1993

By G. E. Maryniak

To date, human space exploration has been almost completely dependent on the use of resources carried with astronauts and cosmonauts from the surface of the Earth. The only exception to this has been the harvesting of solar energy to power space stations like Skylab, Salyut and Mir for long-duration missions. This dependence on materials which must be transported into orbit at costs in excess of $5000 per pound is the fundamental limiting factor in space exploration and operations. It is likely that launch costs can eventually be greatly reduced by means of such innovations as true single stage to orbit vehicles, aerospace planes, or serial electromagnetic or laser launch systems. However, the Earth will always remain an expensive source of materials for space construction and for basic commodities such as propellant and life support liquids and gasses. Fortunately, abundant sources of materials exist which are already in space, outside of the Earth's deep gravity well.

Jan 1, 1992

By A. Marabini, J. Cases, M. Barbaro

Outlined is a review of the application of new selective chelating reagents as flotation collectors; calculation methods for the selection of chelating structures, limitation of the function of commercial chelating agents as collectors, and the synthesis of two new classes of chelating collectors with mixed aliphatic-aromatic structure for oxidized lead-zinc ores. Given are: examples of substituted mercaptobenzothiazole and aminothiophenol structures, flotation and adsorption study of an alcoxyl-mercaptobenzothiazole on cerussite, comparison of adsorption of conventional and chelating collectors, study of the influence of the aliphatic structure1 component on the collecting power of chelating type reagent and the design of chelating collectors with optimal structure.

Jan 1, 1989

By J. M. Richardson, A. L. Mular

Metallurgical balances are fundamental to the successful design and operation of concentration and dewatering circuits. With computerized balance techniques gaining prominence in recent years, it is essential that engineers understand the basic principles that underlie the new methods, as well as the various applications for design of new plants and analysis of existing operations. This chapter discusses two important types of metallurgical balance: (1) steady-state design (2) operating data adjustment Application of computerized steady- state design balancing is demonstrated through the example of a typical copper concentrator flowsheet. Operating data adjustment to achieve a consistent balance is demonstrated for a typical concentrator operation.

Jan 1, 1986

By Jozef F. Zurawski

The paper discusses design and construction of a 1.8 meter (6 ft.) diameter tunnel installed under complex geology of Staten Island, New York. Contract T-13 is a section of the Oakwood Beach Water Pollution Control Project constructed for New York City Department of Environmental Protection. A knowledge of the subsurface conditions and difficulties experienced on the adjacent contracts called for an innovative approach to handle tunneling under 12 to 17 meters (40-55 ft.) of water in the variable subsurface conditions. This paper describes tunnel design and construction utilizing continuous grouting during advancement of tunnel boring machine and installation of liner plates.

Jan 1, 1993

By André Vervoort

At the 2017 ICGCM-conference in Morgantown, WV, a case study was presented with measurements of the upward surface movements or uplift after the closure of two neighboring coal mines (Winterslag and Zwartberg, Belgium). One was closed in the sixties, and the other closed in 1988. The study was based on satellite data (Radar-interferometry or InSAR). The analyses showed both a significant variation of uplift values above the mined area and the surrounding zones, and a variation of the uplift rate as a function of time. In other words, the phenomenon of uplift is complex. At that time, it also was clear that more research was needed to better understand this phenomenon, e.g., an identification of the various mechanisms that are relevant for the process of uplift and the quantification of the various impacts. A systematic analysis of all relevant parameters resulted in a framework that forms the basis for the analytical calculations of uplift values. These calculations show that the main impact is due to changes in the hydrostatic pressure. However, the expansion of the softest parts, i.e., the collapsed or goaf material, is not only important, but the expansion of the (stiffer) non-collapsed strata layers due to a change in pore pressure also must be integrated into the model. For the case study, the partial flooding of the underground after closure of the mine that was abandoned in the sixties is integrated into the model. Larger stiffness values also are applied for this mine, in comparison to the values of the more recently closed mine. Overall, a very good correlation is observed between the InSAR-measurements and the calculated values along a north-south transect.

By Herbert S. Richey

Two hundred years ago next April, our forebears embarked upon the difficult path to national independence. They succeeded, and shook off the yoke of foreign domination. In the ensuing two centuries, the country was mobilized several times to protect that political and economic independence from foreign domination. These efforts were also successful. Thus, as we stand here on the threshold of our third century of political independence, we can thank previous generations and congratulate ourselves for establishing and maintaining the world's oldest republic. Now -- once again -- the United States faces the challenge of foreign intervention into our economy. This time the battleground is resource avail- ability. America has been blessed with enormous resources. Whether we speak of minerals or timber or water or "amber waves of grain," this nation has benefitted from a resource base that is the envy of the world. This asset, coupled with a political system that permitted us to develop it, has been the physical backbone of our independence. Without the economic independence that this resource base has given us, the political independence we fought for would have been tenuous, at best.

Jan 1, 1975

By G. L. Alston

Rigid urethane foam can be used effectively for improving mine air conditioning systems by reducing heat and moisture transfer from mine rock to ventilating air and from mine rock to ventilation ducts, for erecting mine ventilation stoppings and overcasts, for sealings around door frames and bulkheads to prevent air leakage, for preventing spalling and sloughing of roof and rib and for erecting fire-resistant powder magazines and transformer or compression stations. Rigid urethane foam is a tough, cellular material, made by nixing diisocyanate and polyether polyol resin in accurate proportions through an applicator system, then the two chemicals react, the mixture expands thirty times its original volume with 85 to 95 percent closed cells. Within seconds, the mixture solidifies and takes a preset which will adhere to overhead or vertical surfaces. It will adhere to brattice cloth, steel, wood, concrete and rock, Excessive wetness will reduce the adherence, but in such cases adherence can be improved by preliminary application of an absorbent dust such as cement.

Jan 1, 1963

By G. R. O?Neil

The justification for a "ligand- selective' approach to fine mineral beneficiation via flocculation is established initially. Special emphasis is placed upon the need to identify non-selective, interfering and complicating adsorption effects. Specific strategies directed towards the design and synthesis of complementary selective flocculants are detailed using a number of different polymers and chelating agents as examples. In this regard, the affinity of polymer-bound ligands for metallic cations, ligand concentration, possible modes of attachment, the application of spaced-out ligands and other considerations in the preparation of selective flocculants are highlighted.

Jan 1, 1983