Search Documents

By Allan H. Caverson

Over the past nine years a means for measuring the distance between the mine roof and floor has been developed at the White Pine Mine which yields relevant information utilized in the mining operation. The technique known as "convergence!' is an efficient, low cost way for obtaining large quantities of data for predicting roof falls, caving activity, and overall mine stability. From a limited introduction in 1964 related to monitoring an experimental longwall project, the activity of convergence measurements has been expanded to become a production tool now found in all sections of the mine. Presently, the program involves four main types of activity: 1. Monthly measurements in areas known to be active, and in sample blocks scattered throughout the mine for a long-term stability study. 2. Semi-monthly measurements along vital travel roads, belt drifts and compressor sites. 3. Weekly measurements in areas where men are working. 4. Daily measurements in pillar-recovery and caving operations. Today, one field engineer and six technicians are involved full time in convergence work. Rock Mechanics technicians have installed approximately five thousand stations since the start of the program and of this number, over twenty-five hundred active stations still comprise the mine-wide network spread over the more than five square mile extent of the White Pine Mine workings.

Jan 1, 1973

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"During the last ten years great strides have been made, on the Mesabi Range, in the practice of beneficiating low grade iron ore material. By .beneficiation is meant all methods of removing impurities, and raising the iron content to a point where it can be sold in open market, the principal impurities being silica and moisture. The • general processes to which low grade iron ores are amenable are as follows:1. Thermal(a) Drying ; removes hydroscopic or atmospheric moisture. .(b) Calcining; removes carbon dioxide from iron carbonate, molecular water from hydrated hematites, and atmospheric moisture.Roasting; removes sulphur, carbon dioxide, molecular water and atmospheric moisture.Agglomeration; primarily for the purpose of preparing finely divided material for blast furnace; briquetting and sintering.2. MechanicalScreen sizing; removes rock and sand.Classification; removes sand by means of currents of water of varying velocities.Log washing; removes fine sand.Jigging; removes larger particles of impurities than is possible by log washing. Certain types of jigs remove fine sand.Reciprocating tables; recover fine iron particles from sand discarded by above processes.Magnetic separation; applicable to the commercial separation of the magnetic oxide of iron from gangue material. From a scientific standpoint it is possible to separate certain hematites and limonites from their gangue:(g) Miscellaneous processes; comprise dry concentration, electro-static separation and other processes."

Jan 1, 1920

By Rudolf Fahn

Bentonites are best suited for the preparation of acid activated clays with efficient adsorption properties. They are weathering products of acid volcanic ashes and their natural deposits are world-wide spread. The main constituent of bentonite is the aluminium hydrosilicate nontmorillonite with a high ability to swell. Süd-Chemie owns bentonite deposits in Germany and subsidiaries in Italy, Mexico and Arizona.

Jan 1, 1979

By T. Resende, J. Sismour

"Signs in underground mines are subject to variable airflow, which carries dust and moisture. Dust buildup reduces their visibility, hampering production efficiency and safety. Underground workers commonly must stop to clean signs in order to gauge their location, or find critical supplies or services. There are currently a variety of coating products, including dust and water repellants, available on the market that have the potential to reduce dust accumulation on sign surfaces. This paper describes a preliminary study to determine their effectiveness. The study involved a practical testing protocol using a trickle rock duster and samples cut from a clean, used road sign. Product effectiveness, under both dry and wet conditions, was evaluated based on photographic evidence by comparing changes in sign luminosity after a period of rock dust application. By analyzing the frequency of different pixel luminosities on the dust-covered samples, both uniformity of dust coverage and the total amount of accumulation was assessed. Results indicate that at least one product may reduce the amount of dust buildup on sign surfaces and increase visibility. INTRODUCTION In all underground mines, visibility of signage is critical. Signs inform miners of their location, direction toward escape routes, and location of supplies. Over time, sign surfaces can collect dust and can eventually become unreadable. The rate of dust accumulation on surfaces is often particularly high in coal mines, where both mining (e.g., cutting and drilling) and rock dusting activities can contribute significant amounts of dust to the airways. Several factors may contribute to dust buildup on sign surfaces. First, basic principles of fluid and particle flow are at play. When a fluid travels past a stationary surface, the velocity of the fluid at the surface boundary is zero. If a very small dust particle moving with air collides with a surface, it does not immediately fall off since the air velocity is zero at the sign surface. (This is the same reason that dust can collect on a rotating ceiling fan.) Further, once the collision occurs, other mechanisms may help keep the particle there – including friction that resists particle falling due to gravity, and adhesive forces due to humidity and/or static charges the particle and others already on the surface. Currently, the most common way to deal with reduced sign visibility due to dust buildup is for mine personnel (e.g., a compliance foreman, supply worker) to periodically clean sign surfaces – usually just by wiping them with a cloth. As a regular activity, this solution is inefficient; in cases of emergencies, it can also pose unnecessary risks. Application of an off-the-shelf coating to sign surfaces may represent a simple yet effective way to reduce the rate of dust accumulation. There are currently a variety of products on the market that may be suitable for this purpose, including dust and water repellants."

Jan 1, 2017

By F. E. Kottlowski

Widespread high-calcium limestones in New Mexico region are low -in magnesium, but some units include shale interbeds deleterious for sulfur removal usage. Thick limestones in Mississippian Escabrosa, Lake Valley, and Leadville, Pennsylvanian Madera and Hermosa, Pennsylvanian-Permian Horquilla, Permian Hueco and Capitan, Cretaceous U-Bar, and some Cenozoic travertines are high-calcium units. Significant outcrops are in mountains of southwestern, south-central, central, southeastern and north-central New Mexico, southeastern Arizona, southwestern Colorado, and northwestern Chihuahua. Coal-fired powerplants are mainly in northwestern New Mexico and eastern Arizona, thus transport is mainly by railroad.

Jan 1, 1994

By B. G. Long

Coastal States Energy Company (Coastal), a wholly-owned subsidiary of The Coastal Corporation of Houston, Texas, owns coal mining operations in Utah and Kentucky. One of the Utah operations, Southern Utah Fuel Company (SUFCo), located 30 miles west of Salina, Utah, has been operated by Coastal since 1974. This operation is a single-seam, six-section mine operated from one portal area. It produces 2.2 million tons of coal per year and has a payroll of approximately 300 employees, Coal is mined by continuous miners, hauled by diesel-powered haulers and transported by belt conveyor to outside crushing and screening facilities. Sized coal is hauled by contract truckers 80 miles to a unit-train facility located at Levan, Utah.

Jan 1, 1983

By B. A. Rose

Coal is being thermally dried in ever increasing tonnages today. Because of fire and explosion hazards, it is important that drying equipment be designed for maximum safety in operation. It is well then that we review dryer design and operation to bring out those features and operating practices which will provide maximum safety to equipment and personnel. This paper presents the author's views regarding the fundamental requirements for safety and explains the Heyl and Patterson approach to the meeting of those requirements in the design and operation of their dryer.

Jan 1, 1962

By Dennis Z. Mraz

Subsidence profiles over Saskatchewan potash mines exhibit forms which cannot be explained by existing subsidence models. The subsidence is affected by bridging of competent rocks. A modification of the theory can explain the observed displacement of subsidence profiles due to bridging. An unusual shallow secondary subsidence trough has been observed extending two to three kilometers outside the primary subsidence. The secondary subsidence is explained as an elastic compression inresponse to a drop in pore water pressure in the vicinity of the caving zone. The concept of pore water pressure may lead to a safe extraction limit for Saskatchewan mines.

Jan 1, 1986

By Allan Breitenbach

Leaching has been used since the 1600s on unlined ore dumps and since the late 1970s on lined leach pads for the recovery of metals from mined ore, the latter typically called ?heap? leaching and the former ?dump? leaching. Modern day run-of-mine (ROM) or crushed ore heaps are stacked in controlled lifts on lined leach pads and irrigated with a solvent solution (dilute alkaline cyanide for precious meals, dilute sulfuric acid for base metals and uranium). Conventional lined leach pads store process solutions and any storm water, snow melt and cumulative wet season surplus water by gravity flow to external ponds. Impounding valley leach pads (also known as valley fill heaps) differ from conventional leach pads by storing various combinations of process liquid solution and surplus water within internal ponds by using the interstitial pore volume of the ore. While impounding liquids within the heap is simple in concept, impounding leach pads are more complicated for construction and containment compared to conventional leach pads with external ponds.

Jan 1, 2012

By D. L. Madge

The text of this chapter was not received in time for printing.

Jan 1, 1979

By George W. Toth

In a recently completed research project for the U.S. Bureau of Mines - Twin Cities Research Center, a computerized costing procedure for uranium in situ leach mining was developed by the NUS Corporation. This costing procedure, termed a cost model, employs a process engineering approach for estimating total project costs as well as equipment and manpower requirements for uranium in situ leaching operations in either Texas or Wyoming. 80th capital and operating costs are generated by the model along with the overall production cost/pound U3O8 subject to a known rate of return. Conversely, rate of return on equity can be solved for, subject to a given price of yellowcake. During the course of the research effort, this cost model was applied 50 typical site conditions in Texas and Wyoming. Sensitivity rests were conducted for numerous key parameters to determine the cost influence attributable to incremental changes In parameter values. The results of these sensitivity tests along with a description of the in situ leaching cost model have been documented as Bureau of Mines, Mineral Research Contract Report No. J019912, "Cost and Sensitivities Analysis for Uranium In Situ Leach Mining," dated March 1981.

Jan 1, 1981

By T. R. von Ow

The method of powering mills such as AG, SAG and Ball has a long and technically interesting history. It can be said that almost every decade in the last half century had its own trend. The trends were dominated by the market demand, the advanced process development and requirement of the mechanical and the electrical technology but mostly by the price of the applied technology. The increasing size of the ring geared mills in the last years requires more awareness on the drive train solution. Special attention must be paid to the mechanics and the requirements of the power grid. Operational challenges such as soft starting and controlled operation as well as the protection of the equipment have gained importance. Frequency converter drive solutions dedicated to single or dual pinion ring-geared mills offer significant advantages over conventional drives due to their application specific features and controls. Solutions with low speed motors as well as high speed motors cover all possible configurations available for ring geared mills.

Jan 1, 2010

By J. Bigu

Ventilation conditions in working environments are usually studied by anemometry or, in complex cases, b using special tracer gases such as SF6 and 85Kr. in conjunction with chromatographic and radioactivity techniques, respectively. In some working environments, such as underground uranium mines, however, use can be made of the natural radioactivity environment (e.g.. 222rn. 220rn, and their progeny) to investigate mine ventilation conditions of practical interest. Theoretical studies and experimental data in several underground uranium mines and mine locations show that certain thoron progeny to radon progeny concentration ratios are very good indicators of ventilation conditions. Furthermore, the growth and decay of radon progeny and thoron progeny provide valuable information on mine air residence and clearance times. Some specific examples have been analyzed, such as bacterially-assisted uranium leaching operations in a partially enclosed stope, and the effect on the underground environment of turning ventilation fans on and off for a period of time. Air residence times and other variables of interest, determined from the mine radioactivity environment, were compared with more traditional techniques, such as anemometry and tracer gas chromatography. These studies were also extended to a wet non-uranium mine which exhibited relatively high concentrations of radon and its progeny.

Jan 1, 1989

Changes have been made in the Bulletin, Section I., for this month ; Personal and Employment columns have been added, and a Forum, in which will be included letters and discussions of general interest to members of the Institute ; live news and new matter have been inserted near the front; lists of officers and committees are placed next to the technical section, while standing matter and other information which is interesting chiefly when sought for, has been segregated as much as possible. Members are urged to co-operate with the Editor by sending in news items of themselves and others, and by giving some of their spare time to this department each month.

Jan 4, 1913

By Anitava Ghosh

A computer program has been written to simulate ground vibrations induced by multiple- hole surface blasts. The program is an inexpensive and relatively easy to use tool for predicting the principal blast vibration characteristics that determine damage and annoyance potential: peak particle velocity, frequency content and pulse duration. The program generates a complete ground motion history by superposing, at any surface position, the vibrations induced by each individual explosive charge. It requires specification of (hence allows accounting for) the blast geometry, initiation sequence (including random delays), position with respect to blast, pulse characteristics induced by each charge, and propagation laws. A methodology is outlined to determine the necessary variables either on the basis of site investigations (e.g.,velocity, attenuation, single-hole input pulse), or by back-calculation from measured blast vibration records. The latter procedure has been applied to blasts from two coal strip mines. Main difficulties encountered are backcalculating individual input pulses, propagation (especially dispersion) parameters and delays. A normal distribution of delays, based on published results, has been shorn to influence the results and the response of a single degree of freedom structure significantly. Broadening of the wave types included, improved input pulse determination and propagation laws, and more detailed verifications with field results are required in order to make the program more directly applicable to practical situations.

Jan 1, 1986

By E. A. Devuyst, G. Robbins

A unique process for removing cyanide and base metal complexes from industrial waste streams was patented by G.J. Borberly et al. (1984). The process uses SO2 (liquid or gas, or solutions of sulfite salts, or from burning elemental sulfur), plus air that is dispersed in the effluent using a well agitated vessel. Acid produced in the oxidation reactions is neutralized with lime at a controlled pH generally in the range 7 to 10. The reaction requires the presence of soluble copper as a catalyst which can be supplemented by copper sulfate if necessary. The process can be applied to the detoxification of gold and silver mining waste streams, such as carbon-in-pulp (CIP) tailing pulps, barren solution bleeds, pond waters and heap leach rinse solutions and also to plating shops wastewaters. The SO.jAir process has substantial advantages over two of the main alternative methods of cyanide destruction, namely alkaline chlorination and hydrogen peroxide. Alkaline chlorination is highly penalized in terms of reagent consumption. Chlorine is a strong oxidant reacting with species other than cyanide present in the effluent such as thiocyanate and sulfides. Furthermore alkaline chlorination is an incomplete detoxification process. Iron cyanide is not removed and the potential for harmful by-products species exist. Consequently final effluents may be subject to additional treatment in order to comply with regulatory demands.

Jan 1, 1991

By A. K. Sinha

Ever since electricity was introduced, electrical injuries and electrocutions have continued to occur regularly in coal mines. An analysis of the two hundred cases of electrocutions which occurred during 1956 to 1970 indicated that over 50 percent of the incidents were caused by the ineffectiveness or lack of electrical grounding. Research shows that various types of arbitrarily designed ground beds are in use and that the ground resistance and current are often very high and subject to wide seasonal variations. The results of a recent research are discussed in this paper.

Jan 1, 1980

By Steve Kral

Competition in the gold mining industry throughout the world has become fierce in recent years. The challenge facing operations personnel is to produce more gold for less money. Likewise, the explorationist's charge is to find more gold in a more cost-efficient manner. That means using new technology to find new gold deposits and expand present ones. More accurate mapping instruments are available to geologists in the search for new deposits. Advanced geophysical and geochemical methods enable explo¬ration teams to review previously mined districts in their search for minable reserves. Four technical sessions on the geology, exploration, and development of gold deposits were part of the program at `world Gold '89,' a Gold Forum on Technology and Practices," held by SME and The Australasian Institute of Mining and Metallurgy in Reno, NV, Nov. 5-8, 1989.

Jan 1, 1990

By G. Labonte

The behavior of four different redox sensing electrodes (gold spiral, black platinum, chalcopyrite, and galena) during roughing and cleaning flotation is examined and related to the flotation response. Although it is difficult to provide unequivocal interpretations of the different potentials measured, the results indicate that the solution potential (as sensed by the black platinum electrode) is different from that of the pulp potential (gold spiral) and is only weakly related to the flotation response. On the other hand, the potentials exhibited by the gold spiral and the two mineral electrodes are related to the floatation response. The gold and mineral electrodes exhibit different transcient responses during the addition of flotation modifiers (e.g. NaCN, SO2). These responses appear to be related to the reactivity of the minerals and could indicate the conditioning time required to achieve flotation or depression of selected minerals.

Jan 1, 1989

By Alim Elibol, Rosbel Jimenez, Mustafa Can Suner, Deniz Tuncay, Zach Agioutantis

LaModel is a displacement-discontinuity variation of the boundary element method, which is utilized to analyze the displacement and stress in flat-lying, tabular orebodies. In coal mining, the accuracy and reliability of LaModel are proven with the utilization of the Mark- Bieniawski coal pillar strength and the stress gradient formula with proposed methodologies. However, the application of LaModel is limited to coal mines due to the default coal pillar strength properties. Recently, the stress gradient functions have been established and used to derive concentric rings of zones to simulate stone mine pillar yielding in LaModel. Also, to gain a robust understanding of the brittle failure mechanism and its effect on pillar strength, an S-Shaped failure envelope, where rock mass' cohesive and frictional strength components mobilize as a function of confinement (e.g., minimum principal stress), has been implemented into FLAC3D software. Therefore, by employing brittle failure criteria, the pillar strength stages at various width-to-height ratios and different pillar dimensions are estimated for four benching stages. The estimated pillar strengths and stress gradients for benching conditions are then used to calibrate LaModel in-seam material properties and compare stresses computed by LaModel and FLAC3D. Consequently, this study aims to increase the safety measures in the stone mining industry by implementing the practical use of LaModel for underground stone mines' initial development to various stages of bench mining.

Jun 25, 2024