Search Documents

By M. J. McPherson, P. Mousset-Jones, G. Danko, F. Calizaya, K. You

The friction factor is one of the more difficult parameters to determine in ventilation planning. In practice, this can be estimated from published factors such as those of McElroy. The problem with this approach is that the selection requires some judgement, and the estimated values offer no more than guideline accuracy. This study, examines the effects of four factors on the coefficient of friction for a simulated mine airway. The factors are: airway cross-section, asperity height, flow direction, and cross-cut spacing. The study includes the modeling of a mine airway and the evaluation of the results from 13 experiments on flows of air over rough surfaces. The model, physically represented by a wind tunnel, includes a rough surface section which can be modified to simulate mine airways of various shape and asperity height. Most of the experiments were performed under controlled flow conditions during which the Reynolds number was varied between 50,000 and 300,0000. Based on this study, the friction factor for a mine opening was found to depend not only on the size and shape of the surface asperities but is also affected by the orientation of them in relation to the flow direction.

Jan 1, 1991

By B. K. Mishra, R. K. Rajamani

Discrete element is a numerical technique for describing the collision dynamics and motion of an assembly of particles. In particular, calculations are done on full three-dimensional space with a force-contact law for collisions and Newton’s law for subsequent motion. It may be said that there is no empiricism in this approach. The paper describes the full scale simulation of large diameter semiautogenous grinding mill of size 40X24 ft. It is shown that the simulation predicts the power draft of plant size mill extremely accurately. Also these simulations have been adapted uniquely to assess the motion of pebbles and slurry in pulp lifters. The passage of slurry from pulp lifters into trunnion is extremely important since flow-back and carryover must be avoided at all cost. The dynamics of slurry flow through pulp lifters is also described in this paper.

Jan 1, 2003

By James C. Cobb

Middle Pennsylvanian (Desmoinesian) coals of certain areas of the Illinois and Forest City Basins contain epigenetic sphalerite and associated minerals in veins, clastic dikes, cleat, and other small-scale structural features. The presence of sphalerite in these coals records information about the geology of coals and coal basins, and represents a potential source for zinc as a byproduct of coal production. Origin of Sphalerite in Coal The origin of sphalerite in coal suggested by Cobb (1) involves sphalerite precipitation from zinc-bearing ?Na-Ca-Cl brines upon contact with sources of sulfur in the coal bed, e.g., pyrite, H2S, and organic sulfur. These brines were essentially at the temperature of the host coals as determined by fluid-inclusion thermometry and vitrinite-reflectance studies. The migration of these brines into coal beds may have been caused by compaction of sediments due to continued sediment loading of the coal basins. Zones of high permeability such as sandstones and the coals themselves presumably acted as conduits for the movement of the brines. The open spaces where sphalerite was deposited resulted from minor deformation associated with differential compaction and cleat formation enhanced by volume shrinkage during coalification.

Jan 1, 1982

By Victor F. Hollister

Porphyry copper deposits can be categorized into three models for purposes of prospect evaluation: Breccia-pipe, modified Lowell and Guilbert, and diorite models. The modified Lowell and Guilbert model is normally associated with a quartz-bearing intrusive and a potassic, phyllic, argillic, and propylitic alteration sequence. Variations can occur in the alteration zones of this model that range from orthoclase-rich (Kalamazoo, Silver Bell, and Mineral Park) to ortho- clase-deficient (Petaquilla and Bougainville) potassic zones. The unifying features of the model are the presence of a phyllic zone and a quartz-bearing intrusion. The breccia-pipe model (Toquepala) is characterized by structure and alteration related to or controlled by breccia. Where tourmaline occurs in the breccia, the identity of the model is usually clear. However, if tourmaline is not commonly developed in the breccia (La Caridad), the deposit can be misidentified as to model. Porphyry copper deposits associated with quartz-deficient intrusives, whether these are calc-alkalic diorites or alkalic plutons, are characterized by alteration suites distinct from those of the modified Lowell and Guilbert model. These have been generalized as diorite model porphyry deposits. Because alteration and mineralogical development in diorite model deposits is distinct from that of the modified Lowell and Guilbert, ore guides and exploration tactics differ for the two models. The reprint that follows describing the three prospecting models summarizes their features. It is to be emphasized that these are models used in exploration for specific deposit types and are not genetic, tectonic, or geographic models. Porphyry copper deposits can be metamorphosed. Gibralter is an example of a Lowell and Guilbert model deposit that has undergone regional metamorphism.

Jan 1, 1991

By E. Koufetzis

Rock mass classification systems are core elements of tunneling and empirical mine design worldwide. The Bauxite division of S&B Industrial Minerals S.A. decided to implement a rock mass classification system in order to provide mining engineers and supervisors of the underground mines, with guidelines of stability performance and with a complementary tool for the selection of the appropriate tunnel support. The back analysis system employed is based on visual observation of especially selected underground mine sites, representative of all rock types. This fact combined with the failure or success of the already existing support system, constitute the fundamental part of the work undertaken. The paper is divided into three main parts. In the first part the classification methods of Q, RMR89 and GSI are presented and the advantages and disadvantages of each method in connection with underground mining are indicated. RMR89 and GSI are conclusively selected for use, the main criteria for the selection being, the simplicity in use and the competency of the support system suggested for each rock mass category. The second part points out the methodology for measurements, the practical difficulties encountered during this process and the guiding principles followed, in order to avoid these problems. In the third part, the final conclusion of this project is demonstrated and the different rock mass categories are presented with their relative support recommendations, as they were applied and tested in all phases of the bauxite mines? exploitation. The generated methodology is being implemented by the site mining engineers, for validation and potential improvement.

Jan 1, 2008

By James H. Nulty, Joseph S. Roti

INTRODUCTION During a recent panel discussion on the topic of millwater antiscalants, the question was posed: "What would you like to see in the future?" Answer: 'We need an antiscalant that: can be fed without a pump (no maintenance), functions on residual basis (no fault), can be tested for colorimetrically in sub-part-per- mi 11 ion concentrations (no guessing) and will recycle back to the mill from tailings (no cost).” Impossible? Based upon today's level of technology, such a product does not exist. However, a few of the qualifications listed above are certainly food for future thought. Meanwhile, progress is being made in upgrading three essential elements in this critical area of ore processing. They are: 1. Antiscalant reagent research and development. 2. On-line monitoring programs. 3. Reagent storage and feed systems. The objective of this paper is to out- line the current direction being taken in each of these areas and to present case histories as examples of how theory has been applied in field situations to better improve operations. LABORATORY SCREENING TESTS Recent technical papers have explained the various generic chemical raw materials which are available in the marketplace. While the merits of each chemical component are open to debate, the processes used by most major reagent suppliers to evaluate products in the laboratory are fairly standard. Common techniques incorporate both static and dynamic conditions in the search for the most cost effective product. Static Test Perhaps the most common test procedure used is based upon NACE Standard Test Method 03-74, which is "a laboratory screening test to determine the ability of scale inhibitors to prevent precipitation of calcium sulfate and calcium carbonate from solution." The objective of this test is to measure the change in calcium ion concentration in a container of saturated stock solution prepared from calcium chloride and sodium carbonate which is heated in a water bath. After 12 hours at constant temperature (160°), the mother liquor is pipetted into a beaker and a titrated for gm/l of unprecipitated calcium ion. A simultaneous test is performed on stock solution with antiscalant added. The results are then charted to determine the most effective antiscalant (with respect to preventing precipitation of calcite). It should be noted that this procedure examines only the ability of a chemical additive to retain calcite in a saturated solution where thermal stress is applied. This is commonly referred to as sequestration or stabilization. It has been documented that products which act in this manner (i.e., inorganic and organic phosphates) are good scale inhibitors. However, low molecular weight anionic polymers function in a much different manner by distorting calcite crystal size, shape and charge density, thus preventing scale formation. Because of this different mode of operation, static tests may not prove conclusive where polymers and sequestrants are being compared. The simplicity of this test makes it easily adaptable for field use, although modifications are often made.

Jan 1, 1986

By Janusz S. Laskowski

Studies carried out over the last 10 years reveal that precipitating particles which may appear in alkaline solutions of long-chain amines and in acidic solutions of fatty acids exhibit clear isoelectric points around pH 10.6-1 1 for dodecylamine and around pH 2.5-3 for fatty acids. These colloidal species can accumulate at solid/liquid and liquid/gas interfaces and affect flotation. While the precipitate in solutions of fatty acids apparently can chemically interact with the mineral surfaces and is flotation-active if sufficiently long conditioning time is available, the cationic flotation of quartz in alkaline solutions is depressed by the colloidal precipitate. The experimental data available in literature on the adsorption, electrokinetic, contact angle and surface forces measurements in the solutions of the weak electrolyte collectors are analyzed and the role played by the precipitate is discussed. It is shown that these concepts allow for an explanation of the selective flotation of sylvite from halite with long-chain amines in potash ore flotation.

Jan 1, 1999

By David A. Holmes

Zeolites are crystalline, hydrated aluminosilicates of the alkali and alkaline-earth metals. Their crystalline framework is based on a three dimensional network of SiO4 tetrahedra with all four oxygens shared by adjacent tetrahedra. The alkali and alkaline-earth cations are loosely bound within this framework structure and may be exchanged, to varying degrees, with other cations or molecular water. Most zeolites can be reversibly dehydrated. At present, close to 40 natural zeolite minerals have been identified and over 100 zeolites have been synthesized. Zeolites are a family of hydrous aluminosilicate minerals whose physical properties provide unique features for a wide variety of practical applications. Zeolites have been known for more than 200 years, but it was not until the middle of this century that their economic potential and widespread occurrence in sedimentary rocks were known. Since 1950, literally thousands of articles and patents have appeared in technical literature, and commercial pro¬duction of natural zeolites may now exceed 1 Mt worldwide an¬nually. In the past 40 years, the zeolite mineral group has changed from that of a museum curiosity to one of an established industrial mineral commodity. According to Breck (1974), zeolites are characterized by the following properties: 1) High degree of hydration, 2) Low density and large void volume when dehydrated, 3) Stability of the crystal structure of many zeolites when dehydrated, 4) Cation exchange properties, 5) Uniform molecular-sized channels in the dehydrated crys¬tals, 6) Ability to adsorb gases and vapors, 7) Catalytic properties. All zeolites are molecular sieves, but not all molecular sieves are zeolites. Activated carbon, activated clays, alumina powder, and silica gels are also molecular sieves. Molecular sieves are materials that can selectively adsorb molecules on the basis of their size, shape, or electrical charge (Clifton, 1987). Commercial application of zeolites is based on the following physical properties: molecular sieving, ion exchange, adsorption, and catalysis. Potential commercial utilization includes hundreds of possible applications. The principal uses at this time, however, are as fol¬lows: -Ammonium-ion removal in waste stream treatment, sewage treat¬ment, pet litter, and aquaculture, -Odor control, -Heavy metal ion removal from nuclear, mine and industrial wastes, -Agricultural use, such as soil conditioner and animal feed supplement. An estimated 800 kt to 1 Mt of natural zeolites were produced and consumed worldwide in 1991. Eight small operators reported collective production and consumption of an estimated 18 kt of natural zeolites in the United States during 1991, mostly for feed additives and for odor control, aquacultural, agricultural, catalytic, and ion exchange applications (Eyde, 1992).

Jan 1, 1994

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

The STG integrated method of grouting can be divided into the several phases as outlined in preceding chapters. For convenience in describing technical procedures, they can be grouped as: 1. Investigations in non-geotechnical, exploration bore¬holes. 2. Drilling the holes necessary for geotechnical investiga¬tions and for grouting. 3. Conducting appropriate hydrogeologic tests in those holes and consequent calculations. 4. The preparation of a clay mortar. 5. The preparation of a clay-cement grout with additives. 6. The injection of the grout. 7. Checking the quality of the grout curtain. Items 2, 4, 5 and 6 are discussed below. These activities contain the procedural aspects of grouting. 7.1 DRILLING GROUT HOLES Grout holes belong to a very select class of drillholes. The necessary drilling equipment must enable the operator to drill the holes in inclined, twisting directions. In addi¬tion, the equipment must permit drilling under structurally and hydrogeologically complex conditions. The equipment must permit the operator to conduct specific testing activi¬ties in the drillholes. These activities include hydrodynamic analyses, flowmetric analysis, and the installation and re¬moval of deflectors, packers, grouting plugs, casings, lin¬ers, pumping facilities and other work. As explained in Chapters 5 and 6, the grouting of sat¬urated rock is conducted both through holes drilled from the surface and through holes drilled from the face of a shaft, drift, or tunnel. The drilling of grout holes from the surface can be carried out by an aggregate of equipment that can be the same equipment used for drilling exploration boreholes. Depending on the projected depth of the holes, the STG ZIF- 1200MR and ZIF-650 drilling rigs (or modifications of them) are used. The SKB-4, SKB-5 and SKB-7 high-output drilling rigs (workover rigs) have been used in recent years. The STG BMP-24 drilling rigs are used for carrying out the descent-lifting operations for drilling holes from the sur¬face. In a number of cases, the UKB-500C, URB-3AM and URB-2A power-fed drilling equipment is used for drilling holes from the surface. It should be noted that the drilling of grout holes usually requires an electric drive assembly. Drilling with diesel drive assemblies would be used only to preclude the possi¬bility of losing electric power during drilling operations. Turbine drilling would be used only for appropriate techni¬cal-economic reasons. The selection of the grout hole design is determined by the hydrogeological and structural geological conditions at the site as interpreted in Chapters 2 and 3. The design of grout holes must be as simple as possible in order to min¬imize costs. Hole design guidelines can be adopted as a basis for this purpose, unless site-specific conditions require otherwise. The mouth of the drillhole must be outfitted with a guide-pipe having a length of at least 2 m and an outside diameter from 219 to 234 mm. The upper part of the hole must be attached by a jig consisting of borehole casing that has a diameter ranging from 108 to 146 mm. The length of the jig h is determined by the equation [ ] where k = 1.1 to 1.2 is the load factor; P,, is the injection pressure of the grout into the mouth of the drillhole; D is the external diameter of the jig pipe; m = 0.6 to 0.7 is the work condition factor; T[ ].1 MPa is the bonding value of the rock cemented to the jig. The grout hole is drilled from the jig shoe to the de¬signed depth using a rock-crushing bit with a diameter of 93 mm or more. However in complex hydrogeological condi¬tions when the shaft intersects unstable rock, other hole designs can be used. The diameter of grout holes must permit an aggregate of investigations to be conducted in them using down-hole borehole geophysical and flowmetric logging instruments. It is necessary to cement the casing strings reliably in the grout holes, thereby permitting the injection of the grout under high pressure through the pres¬sure tight mouth of the borehole. Technological details for drilling grout holes such as the rotational rate of the drill bit, the axial load on the rock¬crushing bit, and the drilling fluid flow rate are optimized for the specific rock-hydrogeological conditions largely by experience. The hole diameter and type of rock crushing bit are important variables in these details of drilling. It is advisable to drill holes using water as the drilling fluid. However in those cases where the hole walls are unstable or under very high ground water pressure, the use of a well¬ engineered drilling mud should not be precluded. Unfortu¬nately, drilling mud can influence test results. When steeply dipping fractures with inclination angles of more than 60 to 70° are encountered, it is necessary to drill guided, inclined grout holes. This procedure permits the maximum number of fractures in each hole to be stu-

Jan 1, 1993

By Rudolf E. Greuer, Xintan Chang

Mine fires have always been of great concern to mining engineers and their behavior has been studied for a long time. Although an abundance of observations exist, no satisfactory mathematical model for their interpretation and extrapolation has become known. The paper presented here tries to close this gap, making use of the laws of chemical kinetics, energy and momentum conservation. To overcome the mathematical difficulties, the fire zone is axially divided into segments and radially into sections, each one with an extension of only a few inches. Conditions in segments and sections are updated in time intervals of one second or less. To solve the large number of resulting equations, a numerical solution is performed. The model has so far been tried on timber fires. It confirms experimental observations on the ignition phases and equilibria of these fires.

Jan 1, 1987

By W. G. Pariseau, S. C. Schmelter

The destabilizing effect of water pressure on rock-mass stability is examined quantitatively by the finite element method. A coupled code that accounts for the simultaneous effects of rock-mass deformation and transient fluid flow is used for this purpose. The traditional soil-mechanics assumption of an incompressible fluid is shown to be untenable for the analysis of porous, fractured rock slopes. A Mandel-Cryer effect, whish is a transitory but elevated and potentially destabilizing water pressure following a cut, was not observed.

Jan 1, 1999

By S. R. S. Sastri, G. V. Rao

Because the nickel contained in lateritic nickel ores does not occur in an identifiable mineral, it is generally accepted that these ores are not amenable to beneficiation. For this reason, such ores are either directly smelted or leached to extract the nickel. In this paper, a process for enriching the nickel content of the lateritic nickel-bearing chromite overburden, normally a waste material generated during chromite mining, is described. In this flotation process, a nickel preconcentrate containing >1.1% Ni was obtained from material containing as little as 0.36% nickel. An empirical relationship was developed to predict the grade of nickel that can be obtained.

Jan 1, 1997

By Richard L. Bullock, Bruce Kennedy

Vince Lombardi once said, "Practice doesn't make perfect, perfect practice makes perfect." When it comes to building a mine that will operate at the optimum level for the set of geologic conditions from which it was developed, Lombardi's remark might be paraphrased to describe the problem: planning won't guarantee the best possible mine operation unless it is the best possible mine planning. Any sacrifice in the best possible mine planning introduces the risk that the end results may not reach the optimum mine operation desired. This section addresses many of the factors to be considered in the initial phase of mine planning. These factors have the determining influence on the mining method, the size of the operation, the size of the mine openings, the mine productivity, the mine cost, and, eventually, the economic parameters used to determine whether or not the mineral reserve even should be developed. A little-known fact, even within the metal-mining community, is that room-and-pillar mining accounts for most of the underground mining in the united States. According to a 1973 study on noncoal mining (Anon., 1974), more than 76% of the producing mines [of over 1089 t/d (1200 stpd) capacity] produced approximately 70 000 000 t (77,000,000 st) or 60% of the nation's underground tonnage of material by room-and-pillar mining. That same year, 96.8% of the nation's under- ground coal mines produced 262 950 000 t (289,911,000 st) of coal extracted from room-and-pillar mines (Anon., 1976). Thus, nearly 333 000 000 t (367,000,000 st) of the United States' raw material is produced from mines using some form of the room-and-pillar mining system. Because approximately 90% of all mining in the United States is done by some variation of room-and- pillar mining, it is appropriate to give special emphasis to the effects of the various elements of mine planning on room-and-pillar mining. The relationship of these elements to other mining methods will become apparent as the elements are described in later sections herein. TECHNICAL INFORMATION NEEDED FOR PRELIMINARY MINE PLANNING Assuming that the reserve to be mined has been delineated with diamond-drill holes, the items listed in the following paragraphs need to be established with respect to mine planning for the mineralized material. Geologic and Mineralogic Information The geologic and mineralogic information needed includes the following: 1) The size (length, width, and thickness) of the areas to be mined within the overall area to be considered, including multiple areas, zones, or seams. 2) The dip or plunge of each mineralized zone, area, or seam, noting the maximum depth to be mined. 3) The continuity or discontinuity within each of the mineralized zones. 4) Any swelling or narrowing of each mineralized zone. 5) The sharpness between the grades of mineralized zones within the material considered economically minable. 6) The sharpness between the ore and waste cutoff, including whether this cutoff can be determined by observation or must be determined by assay or some special tool; whether this cutoff also serves as a natural parting resulting in little or no dilution, or whether the break between ore and waste must be induced entirely by the mining method; and whether or not the mineralized zone beyond (above or below) the existing cutoff represents submarginal economic value that may be- come economical at a later time. *7) The distribution of various valuable minerals making up each of the minable areas. 8) The distribution of the various deleterious minerals that may be harmful in processing the valuable mineral. 9) Whether or not the identified valuable minerals are interlocked with other fine-grained mineral or waste material. 10) The presence of alteration zones in both the mineralized and the waste zones. Structural Information (Physical and Chemical) The needed structural information includes the following: * 1 ) The depth of cover. 2) A detailed description of the cover including: the type of cover; * the structural features in relation to the mineralized zone; * the structural features in relation to the proposed mine development; and * the presence of and information about water, gas, or oil that may be encountered. 3) The structure of the host rock (back, floor, hanging wall, footwall, etc.), including: * the type of rock; * the approximate strength or range of strengths; * any noted weakening structures; * any noted zones of inherent high stress; noted zones of alteration; the porosity and permeability; * the presence of any swelling- clay or shale interbedding; the rock quality designation (RQD) throughout the various zones in and around all of the mineralized area to be mined out; the temperature of the zones proposed for mining; and the acid generating nature of the host rock. 4) The structure of the mineralized material, including all of the factors in item 3 plus: * the tendency of the mineral to change character after being broken, i.e., oxidizing, degenerating to all fines, recompacting into a solid mass, becoming fluid, etc.; * the siliceous content of the ore; the fibrous content of the ore; and the acid generating nature of the ore. Economic Information The needed economic information includes: *1) The tons of the mineral reserve at various

Jan 1, 1982

By G. A. Hazen, S. M. Sargand

This study monitored longwall mining subsidence profiles over three panels that were mined beneath state highways in southeastern Ohio. The average maximum subsidence was 1.07 m (3.5 ft). The average maximum compressive strain recorded was 0.008 mm/mm. Three predictive methods for the determination of displacements and strains were compared: the National Coal Board (NCB) graphical method, the profile method with empirical constants determined for southeastern Ohio, and a finite element excavation program. Excellent subsidence agreement was found with the profile method, and reasonable strain agreement was determined with the finite element program.

Jan 1, 1987

By Anthony G. Fonseca

The acid leach-solvent extraction processing of oxide copper ores can be improved when selected cation additives are utilized. Bench scale testing showed improvements in both sulfuric acid leaching and solvent extraction processing. Treatment with the method to be described shows improvement in copper recovery in the acid leaching section as well as reduced acid consumption and reduced iron and aluminum dissolution. Processing the copper bearing leach solution with LIX-64N shows increased loading of the LIX reagent which relates to reduced aqueous and organic flow rates, reduced organic loss and inventory as well as a reduction in the size of mixer-settlers. The use of selected monovalent cations controls fluctuations within the pro- cessing system to accomplish the above named improvements. Additionally, these cations are totally compatible throughout the processing system and are quite inexpensive. Bench scale recycle data will be presented both for the leaching section and the continuous solvent extraction processing section up to (but not including) processing the loaded electrolyte. Material balances as well as major solution component monitoring will also be presented.

Jan 1, 1975

By Henry N. McCarl, Gary Waters, William A. Vogely

INTRODUCTION In the past three decades, world trade has grown from less than $100 billion per year in the years following World War 11 to slightly more than $300 billion in 1970 and over $2,000 billion in the early 1980s. Adjusted for inflation, the real growth of world trade in 1972 dollars increased from less than $175 billion per year in the early 1950s to slightly more than $342 billion in 1970 and almost $700 billion per year by the early 1980s. Thus trade as a whole has increased a little more than twofold in real terms in the past decade." Mineral commodities constituted approximately 20% of the value of total world trade in 1970, and significantly more than that proportion in terms of physical volume. By 1980, de- spite rapidly rising petroleum prices, mineral commodities accounted for roughly 18% of the total value of world trade. Crude oil alone ac- counted for about 16%, making it the single most important commodity in international trade. The worldwide recession of 198 1- 1983 brought a dramatic decline in both volume and price of crude oil, shrinking the impact of mineral commodities to roughly 10% of the value of total exports, worldwide, in 1982- 1983. The decline of mineral commodities as a pro- portion of the value of world trade in the decade 1970- 1980 is due largely to the increasing importance of manufactured goods and consumer products such as automobiles and electronic items. During this period, mineral commodity trade expanded roughly sixfold in terms of current dollars to an estimated $350 to 360 billion in 1980. This was equivalent to doubling the real value of mineral commodities in international trade in the 1970- 1980 period in constant dollars. The U.S. Bureau of Mines has expanded the traditional definition of mineral commodities to include semifinished products such as iron and steel (in addition to iron ore), refined metals such as copper, lead, zinc, aluminum, and tin, concentrates, scrap, and petroleum products. Since large quantities of essentially mineral derivatives travel in this form, it is reasonable to use these expanded definitions in stating the role of minerals in world trade. Thus minerals in world trade comprise 30 to 33% of total export trade in all commodities during the period 1976- 1980 (see Table 1.3.1). In addition, the U.S. Bureau of Mines estimates the value of all mineral commodities consumed in the world (at the national level) and compares this value to total worldwide commodity consumption. By this system, mineral commodities range from 30 to 40% of all commodities consumed each year in all countries during the period 1976- 1980 (see Table 1.3.2). The growth in export trade in mineral commodities by commodity group is shown for the period 1976-1980 in Table 1.3.3. These data parallel the swings in worldwide economic activity during the same time period. By any of the above measures, minerals, especially the fossil fuels, constitute a significant proportion of both total economic activity and

Jan 1, 1985

By Edward I. Erlich

1984 saw the 30th anniversary of a momentous event in Soviet geology-the discovery of kimberlites in Siberia, an event that vaulted the Soviet Union to second rank among the world's producers of both gem and industrial diamonds. There are many legends associated with this story, legends about those who predicted the discovery and those who achieved it in the field. The story told here unfolded during the field campaigns of the 1940s through 1960s, as witnessed by the authors and their companies of an earlier generation. This story illustrates science, chance, and human emotions at work, resulting in a blend of conviction, courage, bureaucratic sniping, and competition for glory. At the same time, it is an illustration of the workings of the Soviet exploration system. In a broader sense, it is the realization of the Russian image-boundless natural wealth, indomitable ingenuity, and the rigid political economic system that permeates the Russian landscape as well as the people. Most accounts of the Siberian diamond saga begin with statements such as, "This discovery confirmed the predictions of...", or "It was a result of predictions of one of the greatest Soviet geologists, Academician V.S. Sobelov...". These are only part of the truth. It had become apparent even in the 1930s that the Siberian Platform contained one of the Earth's greatest Basaltic provinces, described in a monograph by Sobolev...; and at the end of the thirties, G.G. Moor of the Institute of Arctic Geology found alnoites, similar in many ways to kimberlites. At the same time, the famous polar geologist, N.N. Urvantsev found other kimberlite like rocks in the southern Taymir Peninsula, adjacent to the Siberian Platform. In publications describing these rocks, Moor and Urvantsev mentioned for the first time the possibility of finding diamondiferous kimberlites similar to those in South Africa. Unfortunately, Urvantsev spent little time in the field between terms in concentration camps. Moor was considered by his superiors to be no more than a good descriptive petrographer; they suggested to him that his conclusions should be backed up by more highly regarded specialists. Thereupon, Moor asked Sobolev to coauthor a paper with him and this became the widely quoted prediction about diamonds in Siberia. Another early paper should also be mentioned, an unpublished paper found by M.I. Rabkin in the geological archives of the Norilsk Metallurgical Plant, written by Yu. M. Sheinmann when he worked in the concentration camp there in the late forties. This report placed the probable location of yet-to-be-discovered kimberlites within less than 100 km of their correct location.

Jan 1, 1990

By J. A. Brierley, R. Y. Wan

Newmont Gold has advantageously used the capabilities of mineral oxidizing bacteria to develop a process for the pretreatment of low-grade sulfidic and carbonaceous-sulfidic refractory gold ores. The biooxidation process results in the oxidation of the sulfidic minerals with increased exposure of gold for subsequent gold recovery. The biooxidized carbonaceous-sulfidic ores cannot be heap leached with cyanide because of the preg-robbing characteristics of the carbonaceous matter in the ores. Therefore, an alternative heapleach process using ammonium thiosulfate was developed to extract gold from these preg-robbing biooxidized ores. The ammonium thiosulfate leach process was successfully applied in both laboratory and pilot plant tests. Satisfactory test results were achieved, encouraging the continuation of process development.

Jan 1, 1998

By Pierre Mousset-Jones, Felipe Calizaya, Malcolm J. McPherson

The objective of this study is to provide potential users of booster fans in coal mines with the necessary information on monitoring and control of fans and environmental factors. The guide-lines listed in this paper were formulated based on the current practice of mine monitoring, the U.S. Code of Federal Regulations on environmental monitoring, and the United Kingdom's National Coal Board recommendations on the use of booster fans. The principles involved in the design of booster fans as well as the provisions needed to guarantee a safe operation of these units, are illustrated by means of an example problem. The example includes a summary of costs for two ventilation systems: a conventional surface fan system and a fully automated booster fan alternative. A comparison of these costs showed that significant gains may be attained by selecting a combined surface-booster fan strategy over a conventional surface fan alternative.

Jan 1, 1989

By R. Fedors, T. Ghezzehei, D. Or

The phenomena of dripping into cavities (e.g., tunnels and drifts) within an unsaturated fractured porous medium under ventilated conditions was studied to improve estimates of dripping rates, drop sizes and the chemical composition of droplets that could affect the integrity of high-level nuclear waste packages placed in drifts. The sensitivity of dripping rates and water chemistry to ventilation was analyzed at various flow rates using analytical expressions linking flow on fracture surfaces to drop formation and evaporation. The model was tested using laboratory experiments involving machined aluminum slabs designed to represent a simplified morphology of a fracture face intersecting a cavity and using natural fracture surfaces from a welded tuff Comparison with ten years of data on dripping in natural caves showed good agreement with model predictions. In particular, for low dripping rates, evaporation due to ventilation leads to larger drop sizes and alters drop chemistry by increasing the concentration of solutes in the drop relative to that in the water flowing on the fracture face.

Jan 1, 2002