Search Documents

By E. D. Hummer

During the planning phase of the fine coal cleaning addition at the Gary Coal Preparation Plant, careful consideration was directed toward the problem of minus 48 mesh refuse disposal. The plant flow sheet included wet screening the raw coal at 1/4 inch, pumping the minus 1/4 inch raw coal to bowl desiltors for desliming, and then cleaning the disliked raw coal on tables. The material to be removed from the circuit as minus 48 mesh refuse consisted of the minus 100 mesh desiltor overflow thickened in two 120 foot diameter thickeners and minus 1 mm screened from the table refuse. Later a flotation plant was added to recover coal from the desiltor overflow, and a classifier replaced the screens to make a sharper size separation of the table refuse at 48 mesh Today the minus 48 mesh refuse at Gary consists of thickened flotation tailings and thickened spiral classifier overflow. The transportation of large quantities of fine wet refuse filter cake mixed with jig and table refuse over existing conveying equipment would have been neither dependable nor economical. Filtration was therefore impractical, and disposal of the fine materials was a problem. The decision was to pump the material to storage ponds

Jan 1, 1965

By Leonard B. Rothfeld

For many years, pulverized coal (PC) boilers in utility power plants have been the dominant market for domestic coal. Today, two new coal utilization technologies challenge the PC boiler's dominance. Atmospheric fluidized bed combustion (AFBC) and "coal gasification/combined cycle" (GCC) stand on the verge of commercial demonstration in the utility environment at a scale of 100 MW. Developed over the past decade, these technologies respond to the demands for cleaner ways to burn coal and for more flexibility in fuel supply. In the near term, these are the "clean coal" technologies most likely to have a significant impact, because they are ready for commercial application. As for environmental acceptability, consider that just a few years ago one of the environmental slogans was "no coal in California." Indeed, the only large quantities of coal above ground in California at that time were in transit on the way to Asia. Today, thanks to new technology, we can point to two operational coal-burning plants in California and one in the works: * Cool Water GCC demonstration plant (100 MW) * California Portland Cement AFBC commercial cogeneration, near Riverside (190 000 lb/hr steam) * Energy Factors AFBC commercial cogeneration at Stockton, to be operational 1988 (44 MW)

Jan 1, 1987

By Michael F. Werneke

While the use of synthetic polymers for solid/liquid separation is not raw technology (1)(its history goes back to the mid 1950's), its importance has increased dramatically over the past decade. This can be attributed to two major factors. The first of these was a change to mechanized mining (strip mining and continuous underground miners) which resulted in a lower quality (higher reject) preparation plant feed, as well as a higher percentage of smaller size particles in the feed. The second factor has been the greater restrictions imposed by governmental agencies on effluent discharge and solids impoundment, requiring pre-treatment of recirculating water before reuse and treatment of refuse before disposal. Today, synthetic polymers find utility in almost all applications requiring separation of solids from aqueous suspension, including "in-process" as well as waste treatment applications. In spite of the fact that there are over several hundred commercially different flocculants available in the marketplace (2), there are a limited number of chemically different materials available which are useful from a cost/performance standpoint. The potential reasons for using flocculants in a coal preparation plant are summarized in TABLE 1.

Jan 1, 1979

By George K. Martin

This paper deals primarily with roof bolting in Kentucky coal mines from January 1, 1949, through December 31, 1954, a six year period. The Consolidation Coal Co? (Ky.), a division of the Pittsburgh Consolidation Coal Co., began systemmatic roof bolting in November 1948 in Mine #204, Elkhorn #3 Seam, at Jenkins, Kentucky, After the efficiency of roof bolting had been proven by the Consolidation Coal Co., this procedure was adopted by other companies throughout the state. In December 1954, approximately 46.4 percent of Kentucky's total production of coal from underground mines was obtained from roof-bolted areas. Statistics in this report will show the progress made in roof bolting during the six years, in addition to the roof bolting being done as of December 31, 1955. Significant progress has been made in the coal mines of Kentucky in reducing the roof-fall fatality, rates, during the past several years by adopting systemmatic roof bolting. The ground work by the Consolidation Coal Co, (Ky.) in cooperation with the Federal Bureau of Mines was based upon the previous experience of the St. Joseph Lead. Cc, in its Southeastern Missouri Mines and The Tennessee Coal and Iron Division of the United States Steel Corporation. The author gratefully acknowledges the cooperation and assistance given by officials of the various mining firms using roof bolts, the Kentucky Department of Mines and Minerals, and the Federal Bureau of Mines in furnishing photographs and information.

Jan 1, 1958

By T. P. Harrington

Research efforts are just beginning to identify the acoustic signatures of very short pulses of sound associated with the fracture of single particles in an autogenous mill. This presentation will discuss the anticipated correlation between these data and the fundamental mechanisms of rock fracture It is hoped that further tests will help identify what design and operating parameters influence the acoustic spectra, determine whether different minerals have different spectra and correlate product particle size distribution with acoustic spectra.

Jan 1, 1980

By Roger K. McLimans

Sphalerite in the ores is multi-banded. Based on color and textures, bands in samples separated by a few kilometers may be correlated. Darkness of color is directly related to iron content. Isotopic and fluid inclusion data indicate that temperatures of ore deposition were 225°C-50°C. The agreement between these two sets of data suggests that chemical and isotopic equilibrium were established. The salt content and hydrogen and oxygen isotopic compositions are similar to present-day values of oil field brines suggesting a similar mode of origin. Ore transport and deposition are not adequately explained by either chloride or bisulfide complexing. Necessarily, other mechanisms were involved.

Jan 1, 1979

By Sean Dessureault

The mining industry has used fleet management systems (FMSs) for decades. These systems were developed long ago in large truck-and-shovel mines, where hardware sales were the core business driver for vendors. These traditional models can be overhauled in the era of the Internet of Things (IoT), Big Data, gamification and low-cost tablet technology. Relatively low-cost tablets are ubiquitous in modern life, and they are packed with communication radios and sensors like Global Positioning System (GPS) and inertial measurement units used widely for games, fitness measures and navigation. These powerful computer devices provide the same, if not more, sensing capability than traditional fleet management hardware, all at a fraction of the cost and without complicated cables or challenging supply lines. 

By R. Bhima Rao

Performing a magnetizing roast in a furnace or kiln is a well-established technology. However, the use of microwave heat for the magnetization of hematite in the beneficiation of ferruginous bauxite is a new approach. This paper reports on an investigation of this procedure, which is followed by comminution and magnetic separation. The results of this investigation indicate that a nonmagnetic product containing 80% A1203 and 2.5% Fe203 with a recovery of 80% can be made from a crude bauxite ore containing 55.9% A1203 and 5.6% Fe203. This product is suitable for refractory use. The mechanism is explained by the ability of the microwave radiation to heat specific points within the bauxite. These heat-specific points are at the location of iron minerals. In a reduced atmosphere, the microwaves promote faster conversion of the iron minerals to a magnetic phase, which improves the magnetic-separation process.

Jan 1, 1997

By S. O. Yuan, R. L. Grayson

As a followup to a USBM-sponsored research project, the authors utilized the knowledge-base structure and system concepts from a Sun Sparcstation-based worker-scheduling system of the mine-management support system to develop a PC-based application. The new software adopts the nested-window concept to facilitate data collection and modification on personnel, including their availability and work priorities during a shift. The system can optimally allocate manpower on a work shift and can delineate supervisory training responsibilities. The various components of the software, including enhancements made to the original system, are described in detail.

Jan 1, 1998

By Richard A. Brown

The direct precipitation of uranium with hydrogen peroxide has been known since 1877. Commercial use of the process began in the 1960's. During 1967 the Bureau of Mines assisted the Climax Uranium Co., Grand Junction, Colorado in the development of a uranyl peroxide precipitation process to control a molybdenum impurity problem (1). Atlas Minerals, Moab, Utah has used hydrogen peroxide to control vanadium and sodium levels in their uranium concentrates since 1969 (2). Recently, the use of hydrogen peroxide by the uranium industry has grown, particularly since the increased demand for uranium has led to the processing of low grade ores. Impurities present in low grade ores can be concentrated with the uranium during milling and will substantially complicate the refining of uranium yellowcake concentrates. Consequently, commercial nuclear fuel processors have imposed stringent specifications and penalties to control these impurities. The ability to produce a pure uranium yellowcake can eliminate penalty or reprocessing costs. Hydrogen peroxide precipitation of uranium is specific and quantitative, producing a very high purity product.

Jan 1, 1980

By Bill Kendall

"In coal mines, handheld air, electric and hydraulic powered drills are used along belt conveyors, in single entry development, in entries where there are obstructions, and in longwall recovering bolting. In hard rock mines, pneumatically powered jackleg drills are typically used in narrow vein mining. Drilling and bolting in narrow confines has traditionally been performed with pneumatically or hydraulically powered hand-held drills or newer electrically powered hand- held hammer drills due to their low cost, simplicity of operation, and extreme flexibility due to their small size. Mechanized equipment has typically been too large, too expensive, inefficient due to the confined space, and too restrictive due to lack of flexibility for use in narrow confines.Although the handheld equipment is effective, it requires operator exposure to certain inherent hazardous conditions in use. These include falling rock from the roof, rib and face; tripping hazards; bending twisting lifting hazards; high noise levels and chemical fumes from the pneumatic exhaust. The operation of the hand held equipment can adversely affect the long-term health of the operator - continual jackleg operation frequently results in longterm damage to hearing, shoulders, arms and wrist joints and back injuries. This results in a reduction in life style for the operator and higher personnel turnover rates for the mining company.Hand-held drills also typically have limited thrust and torque capability that limits their ability to push long resin bolts, inadequate torque to properly install resin bolts or to properly torque mechanical or tensioned rebar bolts. Hand-held drills do not offer any type of protection for the operator from roof or rib falls. They do not offer any means for handling roof or rib mesh. Since the operator stands on the ground the maximum safe drilling height without use of a ladder or "riding the drill" is limited to 2.44 m (8 ft)."

Jan 1, 2014

By William Gleason

"The mining industry tends to focus on very large numbers, whether it’s talking in terms of size of deposits, tons of material mined, the equipment used or the dollars spent. The numbers associated with mining projects are often in the hundreds of millions, but sometimes it’s the little things that can have the biggest impact.Take, for example, the Rosemont Copper Project in Arizona. Owned by HudBay Minerals, the Rosemont Copper project, when in production, is expected to be one of the largest copper mines in the United States, accounting for about 10 percent of total copper production with annual production expected to be 110 Mt/a (243 million lbs/year). However, the project is currently mired in a years-long permitting process. At the 2017 SME Arizona Conference in Tucson, AZ, Kathy Arnold, director of environmental and regulatory affairs for Hudbay Minerals, spoke about the project and the efforts to get it into production.She opened her presentation with the unfortunate news that her 2017 presentation would not be that much different than the 2016, 2015 or 2014 presentations she gave to the same conference. That’s because, as of Dec. 4, 2017, the project had been in the permitting process for 3,797 days, more than 10 years. The process began when Rosemont submitted its initial mine plan in 2006 and a revised one in 2017. The official start to Rosemont Copper’s National Environmental Policy Act (NEPA) started in 2008.In June 2017, the project received its Final Record of Decision from the U.S. Forest Service, moving it a step closer to production. Yet it still faces stiff opposition from opponents while it works to secure the Clean Water Act Permit from the U.S. Army Corps of Engineers and to complete its final mine plan of operations.In her presentation, Arnold said the long process taught her many lessons, including approaching things with a different mindset. More than 130 pages worth of public comments have been collected over the years. The concerns expressed range from lighting issues to pavement to preserving land for a jaguar that was spotted on the property and named El Jefe.“A lot of things that people worry about seem to be small things, but we had to have a different mindset and be open-minded to the concerns,” Arnold said. “That is the commitment we made.”"

Jan 1, 2018

By J. M. Christian

Silver has been a much maligned metal in recent years. In the last three and a half years the price has fallen from around US$7.00 -$7.80 to as low as $3.50 this spring. It has consistently under-performed most other precious metals in the past few years, and has fallen to its lowest levels since the late 1940s in inflation-adjusted terms. Perhaps this is beginning to change. Since April, silver prices have outperformed gold and platinum. While this may continue in the years ahead, key questions remain regarding the pace and timing of any future silver price advances. I want to talk about the supply and demand factors that have led silver to its recent position. Also, I will outline a possible path for silver supply, demand, and prices for the next several years. Before I dive into my discussion of the silver market, allow me to explain who I am. One of the points we always make to clients early in a relationship is that, when you are listening to someone's opinions, you always must remember who it is you are listening to, and why he might be saying whatever it is he wants you to hear. So often, people take opinions from brokers, traders, or investment advisors as gospel truth, never stopping to ask themselves two key questions: Is there any reason to believe that this person knows what he is talking about, and, second, is he trying to sell me something, in telling me this.

Jan 1, 1992

By J. W. T. Ropkins, D. Allenby

The paper describes a technique by which large concrete boxes are unobtrusively inserted beneath existing highway and railway infrastructure to form new subways, culverts and under-bridges, thus avoiding the inconvenience and costs of disruption to traffic associated with traditional cut and cover techniques. A series of project examples, undertaken in the United Kingdom and United States, are used to illustrate the design and construction of the box structures, together with the technology required to control ground disturbance in the tunnel face and around the box, and the jacking systems necessary for box installation.

Jan 1, 2003

By W. F. Visser

The growing availability of information and data analysis capabilities provides new opportunities for improving the performance of operations. By using real-time measurements and artificial intelligence, it is possible to respond faster to changing conditions, while accurate and timely information permits the rapid evaluation of changes and fast business improvement decisions. This paper presents a blueprint for system alignment, organizational design and management practices to leverage these developments in performance-driven operations management in mining and mineral processing.

By K. Soucek

Extraction of hard coal reserves, but also of mineral resources in general in the underground coal mines includes in itself many anthropogenic interventions in the earth crust. These interventions are closely associated with the solution of stability problems in the mine and with occupational safety. One of potential applications of such geo-technical interventions in rock mass is the chemical grouting technology. The chemical grouts are very suitable to affect the physical and chemical properties of rock mass. With the present development of chemical grouts, primarily based on polymers, there come into existence new composite materials during the grouting process (the so called geo-composites), which properties significantly differ from the original rock. An important factor, which affects a choice of chemical grouts and at the same time the effectiveness of grouting technology is the resulting properties of geo-composites. The properties of a coal geo-composite differ from the ones of the unmodified coal seam. On the basis of the laboratory geo-mechanical tests, the differences of properties of both material types were found. While the pure coal samples were destroyed very brittle and explosive, the geo-composite samples were making higher level of tenacity and load bearing ability after overstep of material strength. The presented paper discusses the different behaviour of these original and modified coal samples. The X-ray CT scans were used for observation and demonstration of failure evolution in these samples of pure coal and coal geo-composites after compressive loading.

Jan 1, 2006

By Donald C. Rotherham

The Endako, British Columbia, deposit was initially discovered in 1927 by two local men, Charles H. Foote and Alf Lagdon, who were at that time on a hunting expedition. Four mineral claims were located to cover an area of quartz-molybdenite float that was centered on two small ridges. They subsequently uncovered a 0.5-m (1.6-ft) wide vein on which an inclined shaft was sunk to a depth of 8.3 m (27.2 ft) in 1934. Additionally, a short adit was driven to intersect another vein. Numerous trenches and small pits were also dug. Small test shipments of vein material from this early work were sent to G.S. Eldridge and Co. in Vancouver for metallurgical testing. A concentrate assaying 89.2% MoS, was produced with a recovery reported as 93.3%. The concentrate was essentially free of copper, arsenic, and phosphate. The property was examined by many geologists and engineers during 1934 to 1952, but the only work done was undertaken by the owners in order to maintain their claims in good standing. In 1952, Kennco Explorations (Canada) Ltd. carried out a limited program of bulldozer trenching, sampling, and geological mapping before relin- quishing their option. In 1956, American Standard Mines Ltd. acquired an option on the property, but no assessment work was apparently recorded and the property was allowed to lapse. The key claims were restaked in 1959 by C. Riley and H.T. James of Vancouver. The property was optioned from the new owners by Andrew Robertson in July 1961, and a small amount of trenching was conducted. Robertson, on behalf of his own company, R & P Metals Corp., reoptioned the property in January 1962. The initial results of this work were favorable and justified further exploration. The additional finances required to continue the program resulted in the formation of Endako Mines Ltd. (N.P.L.) on June 21, 1962. Field work by R & P Metals and the first Endako Mines exploration was directed by Bob Couts.

Jan 1, 1991

By Ralph E. Weeks

Utilization of true in situ technologies for mining copper in Arizona will involve a complex environmental permitting process. This process is a key factor in determining the feasibility, costs, and implementing time frames required for development of this innovative mining method. The regulatory structure in Arizona is presently changing due to enactment of the Environmental Quality Act (EQA) of 1986 and development of new aquifer protection rules and regulations. The Bureau of Mines has reviewed the comprehensive hydrogeologic characterization, ground water monitoring, mechanical integrity testing, well construction, contingency planning, and other regulatory elements that will serve as mechanisms to assure protection of ground water resources. The purpose of this paper is to inform the domestic copper industry of the significance of the new Arizona regulatory structure and its implications for prospective in situ operators.

Jan 1, 1988

By Ralph Musick, Brian Briggs

The U1h Shaft Project is a design/build subcontract to construct one 6.1 meter(m) (20 feet [ft.]) finished diameter shaft to a depth of 321.6 meters (m) (1055 ft.) at the Nevada Test Site (NTS). Atkinson Construction was subcontracted by Bechtel Nevada(BN) to construct the U1h Shaft for the Department of Energy (DOE). The project consists of furnishing and installing the sinking plant, construction of the 321.6 m(1055 ft.) of concrete lined shaft, development of a shaft station at a depth of 297.5 m(976 ft.), and construction of a loading pocket at the station. The outfitting of the shaft and installation of a new hoist may be incorporated into the project at a later date. This paper will describe the design phase, the excavation and lining operation, shaft station construction and the contractual challenges encountered on this project.

Jan 1, 2001

By L. A. Puchkov

Problems of how to use artificial intelligence (AI) methods and expert systems (ES) to control complex industrial projects have lately become significant in practical terms. Mining ventilation systems undoubtedly belong to complex multi dimensional objects of control with stochastic nonstationary and nonlinear processes. Formal models based on automated ventilation control, do require awkward algorithmic solutions, moreover, a number of tasks become the operator's headache, and the quality of their solution depends on his experience and intuition. These tasks include: - identifying pre-accidental situations and determining their causes; - making well-grounded decisions with regard to changing ventilation regimes, forecast of mining operations taken account of; - controlling ventilation systems in emergency situations, e.g. when in accident, etc. It is in this context that we have for a number of years been investigating how to practically use AI methods for operative control in dynamic aero-and-gas mining processes, one of our research directions being devoted to working out a consulting programme for the ventilation system operator. Our researching and modeling problem was identification of aero-and-gas situation in different parts of ventilation network and its interpretation in order to determine possible causes for gas regime changing and unexpected consequences. We would single out the following stages in this task: I. Operative information procession coming to the data base from the sensors and analysis of hypothetical versions (using the associative rules base) with regard to factors which have caused significant parameter fluctuations (e.g. C%(t), H(t), Q(t) etc.)., 2. Selection of hypotheses in the knowledge base and forming conclusions in accordance with reliability scale. 3. Clarifying the obtained conclusions in dialogue with the operator. 4. Correcting the associative rules base.

Jan 1, 1992