Search Documents

By D. Randall Crooke, Ron R. Jorgenson

Many coal combustion products (CCPs) have historically been unsuitable for placement as mine backfill because of their physical and geochemical properties and/or regulatory status. However, innovations in paste production and transport of CCPs utilizing the high, fine particle contents of these fine-grained waste materials and their water retention colloidal properties produce a non-segregating, self-cementing material that may be environmentally suitable for placement as mine backfill. Both industry and the regulatory agencies are enthused by the possible cost reductions, both in design and construction of disposal sites, and the reduced environmental impacts of CCP realized by implementation of this new use/disposal technology.

Jan 1, 2001

By A. Almeida, D. Castro, K. Ingmarsson, D. Ferreira, R. Tamir

Mine-to-mill improvements can be initiated at any stage, but it is our assertion that drilling accuracy is a practical anchor in any operating mine or quarry for a structured continuous improvement process. This paper will: 1. Define deviations from plan and provide some best practices for maintaining drilling accuracy. 2. Introduce tools and methods to monitor and calculate consequences of accurate versus inaccurate drilling. 3. Demonstrate the use of these tools and methods and their impact on one cost item, the mitigation of oversized material by a hydraulic hammer. 4. Provide recommendations for implementing improvements.

Feb 1, 2023

By Rudrajit Mitra, Erik Hulthen, AARTI SORENSEN, TOBIAS HARTMANN, ELISABETH CLAUSEN

There has been an ongoing debate on how to transform engineering education to better prepare students for today’s professional world that is characterized by increasingly complex problems and challenges that engineers are tasked with upon entering the industry. While numerous publications have addressed possibilities of how experiential, problem-based, project-based and active learning can be integrated into the engineering curriculum, there has been little attention on mining engineering with respect to adopting this approach. This paper addresses the possibilities of integrating entrepreneurship education into mining engineering programs in order to foster discussion among academics from mining engineering on how to infuse value-creation experiences across the curriculum on a course, program and departmental level.

Sep 1, 2022

By Duane L. Whiting

The National Environmental Policy Act of 1969 (NAPA) provides guidance for federal agencies in making informed decisions. The Act has been used to determine the potential environmental impacts from mining and other natural resource operations, primarily in the Western USA. To accomplish the purpose of the Act, a process for developing environmental documents was established. The documents (EA/EISs) evaluate environmental impacts and are produced by federal agencies through public participation and cooperating agency review. Effective interactions and up front coordination between agencies and industry is required. An abbreviated history of environmental protection in the USA leading to NEPA, the driving regulation, objectives, provisions and limitations of the Act, and select mining related NEPA projects III the Western U.S. are discussed in this paper.

Jan 1, 1998

By R. Bhaskar

The results of an experimental study on the dispersion and deposition characteristics of fine coal dust in mine airways are presented. Experiments were conducted at various flow velocities using bituminous and semi-anthracite-coal dust which had a large proportion of dust in the respirable size range. Cross sectional variations in the concentration of dust at various points in the airway were also measured. Instruments used in the experiments included gravimetric samplers and impactors. Concentration measurements were made both for the respirable and total airborne dust. The experimental design, sampling procedures and results are discussed. The study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground mine airways.

Jan 1, 1986

By T. W. Beck, J. A. Organiscak

The U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling dust and gas. Redirecting all the air toward the face equally up both sides of the machine increased the dust and gas concentrations around the machine. When all of the air was redirected toward the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face, at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all of the scrubber exhaust was redirected toward the face either up the off-tubing side or equally up both sides of the mining machine.

Jan 1, 2013

By Saurav Kumar, Akshay Kumar, Vinayaka R. Kiragi, M. K. Banerjee, Amar Patnaik, Vinod Kumar

Today’s industrial technology offers to optimize and reutilize the resources available in terms of scum that remains after hot rolling in steel rerolling mills in Rajasthan, India. Vast reserves of low-grade coal exist and tons of mill scale are produced everyday after hot rolling in steel rerolling mills in Rajasthan, India. The present research work aimed to optimize the various parameters of solid-state reduction of mill scale using low-grade coal from Rajasthan, India. This study investigates the effect of reduction temperature (850–950 °C in steps of 50 °C), reduction time (60 to 180 min, in step of 60 min), mill scale size (800– 300 μm), and mill scale to coal ratio (1:1, 1:2 and 1:3) on achievable metallic iron percentage and its metallization. A higher percentage of iron content is obtained at a lower particle size of 300 μm. The structural analysis is carried out on 300 μm mill scales using XRD analysis, which shows the percentage of iron is approximately 63%, and metallization above 80% can be obtained under the reduction temperature at 900 °C for 180 min, for 1:3 ratio (mill scale to coal ratio). The chemical composition of the mill scale is obtained using X-ray fluorescence (XRF), and particle sizes as well as distribution of mill scale are determined by scanning electron microscopy (SEM). The elements present in the mill scale are also verified using EDS, which indicates the presence of a major portion of Fe, followed by Fe2O3, Si, and C, respectively.

Aug 14, 2020

By R. N. Edwards

The Magnetometsic Resistivity (MMR) method is based on the measurement of the low-level, low-frequency magnetic fields associated with non-inductive current flow in the earth. The traditional resistivity method maps the electrical properties of the earth by measuring the electric field caused by galvanic current flow between a pair of current electrodes. The MMR method differs from it in that the potential electrodes are replaced by a sensitive coil or magnetometer and a component of the magnetic field due to the current flow is recorded. The presence of an inhomogeneity redistributes the current flow which results in a perturbation of the electric field and, usually, of the magnetic field. The electric field immediately above a relatively conductive inhomogeneity must, by Ohm's Law, be smaller than that expected for a uniform earth. The current density in this region is also reduced but the current density within the inhomogeneity itself is enhanced so that the horizontal component of the magnetic field measured above the inhomogeneity is usually larger than that expected for a uniform earth. A method of interpretation using the magnetic anomaly was patented by Jakoskyl in 1933 but it met with little success at that time. Part of the problem was undoubtedly with the instrumentation, and only recently have robust instruments of sufficient sensitivity been developed2 and field data of good quality obtained. There are many common configurations of the potential and current electrodes in the resistivity method. Similarly, in the MMR method one or both current electrodes may be moved with the magnetometer, either horizontally or vertically ( in a bore-hole), or the current electrodes may be maintained in fixed positions and the magnetometer alone moved. The MMR anomaly is defined as the difference between the

Jan 1, 1975

By Amy McBrayer, Andrea Brickey

The paper discusses the mine planning methods used in the Powder River Basin (PRB), highlighting the differences from open-pit metal mines. It emphasizes the need for agile mine operations due to changing commodity markets and the challenges faced by the coal industry, such as volatile prices and reduced engineering manpower. The study includes a survey of mine engineers to document current practices and identify potential improvements.

Sep 1, 2023

By C. W. Schultz

Earlier publications from The University of Alabama have indicated that column flotation performance is improved when operating at low pulp levels and when the feed is directed into the froth phase. To validate these early observations a series of tests were performed in which the position of the feed entry to the column and the pulp-froth interface were systematically varied. The optimum grade-recovery relationship was achieved with high feed entry (WA) of column height) and very low pulp levels (<10% of column height). The position of the pulp-froth interface appears to be the more critical variable. When operating in this mode (1. e. at low pulp levels) column flotation becomes. in reality. a froth separation process.

Jan 1, 1991

By A. G. Provost

On April 3, 1981, Harrison Western Corporation was awarded a contract by Amax Alloy - A Division of Amax Inc., to sink the Henderson #5 ventilation shaft. The project was located on the Henderson Mine site 88 kilometers west of Denver near the town of Empire, Colorado (Figure I). The Henderson No. 5 Shaft, located in an Alpine environment at an elevation of 3145 meters, was a 9.8 meter diameter concrete lined shaft with a total depth of 793 meters. Work started and continued with Harrison Western employees until January 15, 1982. At that time, Amax made the decision to continue the shaft-sinking with their own labor, and with Harrison Western providing supervision under a management service contract. Shaft sinking continued under this arrangement to October 1, 1982, at which time Amax put the Henderson No. 5 project on standby status until further notice.

Jan 1, 1986

By J. L. Workman

The stability of spoil and highwall slopes are important to successful strip mining. This paper discusses soil parameters of importance in stability analysis. The common mechanisms of spoil failure are discussed. Modes of highwall failure are also outlined. The importance of water to stability is presented. Dragline mining methods most suited to creating spoil and highwall profiles that address stability needs are provided. It is concluded that groundwater and surface runoff must be well controlled, and that it will often be necessary to modify spoil and highwall configurations to achieve a stable overall slope angle.

Jan 1, 1996

By Joseph G. Selmeczi

Lime and limestone-based SO2 scrubbing processes have demonstrated reasonably good success in removing low concentrations of SO2 from flue gases. While most of the operating problems experienced in the early days of scrubbing have been worked out, problems usually increase and removal efficiency drops with increased amounts of SO2 present in the gas stream. In order to overcome these difficulties, yet still taking advantage of lime and limestone as the lowest cost neutralizing agents, a host of so-called double- alkali systems were developed. These processes take advantage of cations such as Na+ and NH4+ capable of forming highly water soluble bases or basic salts, such as hydroxide, carbonate or sulfite, which having been neutralized or acidified by the absorbed SO2 can be regenerated with a lower cost base such as lime.

Jan 1, 1974

By A. Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5M tons. Trona is an evaporite mineral that is processed into several products, mostly soda ash. The underground mine has two active development panels and one longwall (LW) panel. The mining horizon is about 500m below surface and the surrounding strata liberates methane. Three surface-based, blowing fans provide ventilation air as a positive pressure system. The mine operates a 225m long LW face, built by Joy Mining Machinery. Headgate and Tailgate developments are driven with four entries. The recovery room, at the end of each panel, is 8m wide with three access chutes. Additional recovery room support comes for concrete blocks used with a center to center spacing of 1.5m. As the LW enters this pre-driven recovery room there are notable responses and shifting ground stresses. This study was undertaken to measure the ground response using seven vibrating wire displacement transducers. These devices were used to monitor the convergence as the LW approached the recovery room. The methane concentration in the air ventilating the recovery room was also monitored. The correlation between convergence and gas liberation was then studied. The results show that the convergence varies from 0.1m to 0.25m along the length of the recovery room. Ventilating the recovery room becomes critical as methane is liberated from oil shale as the more plastic floor material is disrupted. Appropriate methods are employed to ventilate the recovery room.

Feb 23, 2014

By G. J. C. Young

The paper describes the replacement of a conventional filtration, clarification and zinc precipitation plant by a carbon in pulp (CIP) electrowinning plant, with the objective of improving the recovery of gold from cyanide leached, acid plant calcines. The discussion covers the early laboratory studies to the design and erection of the full scale plant. Particular emphasis is placed on the problems encountered with commissioning and the strategies which were employed to solve them.

Jan 1, 1982

By M. A. Anderson

After mope than fifty years Of Continuous operation, the Nevada Mines Division found itself faced with declining ore headings and metallurgical efficiencies, and rising operating costs. Although intensive process improvement programs had been initiated at various times in its history, insufficient return on investment served to defeat plans for any major changes in circuitry. The advent of practical large-volume flotation machinery, along with the success of long-range exploration drilling programs, complimented the results of an intensive program of research and development. The result of laboratory testing, pilot plant testing, and full scale plant tests was the proven indication of metallurgical improvement given increased flotation residence time and the effect of mechanical agitation in flotation.

Jan 1, 1975

By J. Villeneuve, G. Fourniguet

Simulation of Mineral Processes is now commonly used by the Engineers in charge of plant design or optimization but a good knowledge of the simulation tool is still needed to conduct a project. A new level of algorithm has been defined above the simulator to answer directly to the user&apos;s questions. This level has been called the supervisor of simulation, which is using the automation concepts of sensors and actuators. At any place of the flowsheet (i.e., a stream or an equipment), the user may indicate which value could change by graphically implementing an actuator. Then, he can evaluate the effect of the variation of this value at any other place of the flowsheet by inserting a sensor. Thus, by example, it becomes possible to look at the evolution of the recoveries and/or the circulating loads when scanning an interval of the possible teed flowrates. This approach conducts to an increased facility in using a simulator and in analyzing the predictions. It is also a very valuable tool for permitting to characterize the sensibility of the simulation results to the variation of some settings (e.g., load of grinding media, rotation speed, water addition, etc.) or feed characteristics (e.g., flowrate, sizes, grades, grindability, etc.). Thus, the most important variables can be identified for design and pre-control optimization of plants. This new level of simulation will be implemented in a further version of the USIM PAC simulator and selected examples are presented.

Jan 1, 1995

By Reece Kurre, Gabriel Walton

"Roof bolting has long been used in underground mines across the world to provide ground support. Modern roof bolts are cheap and easy to install with the use of specialized machines as a part of the production cycle. Lhoist North America’s Crab Orchard Mine is an underground room and pillar limestone mine that uses mechanically anchored roof bolts for ground support. The mine currently employs two different roof bolting patterns: a standard 5 × 5 foot pattern, and a 2.5 × 2.5 foot pattern for use in areas with particularly hazardous roof conditions. The purpose of this study is to evaluate the relative effectiveness of each bolting pattern.A series of numerical models were created using RocScience’s RS2. The models were based on a symmetrical section of the mine at its deepest point, and were modeled using Generalized Hoek-Brown failure criterion along with a discrete fracture network. A series of sensitivity analyses were performed on the models by varying parameters such as joint friction angle, crack persistence, joint randomization, and tensile strength of the limestone. Based on the results of the original models and sensitivity analyses, it appears that the standard bolting pattern provides sufficient roof support capacity under almost all the expected conditions at the mine, since factors of safety below the design value of 1.5 were only found for individual bolts in a few of the worst test cases considered. These results can help improve the Mine’s productivity and reduce operating costs without compromising safety.INTRODUCTION AND CASE STUDY DESCRIPTIONLhoist North America’s Crab Orchard Mine is an underground limestone mine located in Crab Orchard, Tennessee. The mine is located under an 800-foot-high mountain, and outcrops on three sides. The mine is accessed through three separate portals and has two main levels, along with a partially developed third level. Extraction is accomplished by the room and pillar method using 50 × 50 feet pillars and 50 × 50 feet rooms. The mining height is limited to 50 feet to keep the pillar width to height ratio around 1.0. Each heading is excavated in a two-stage process that consists of a 30-foot-tall top heading and a 20-foot-tall bench. A distance of at least 30 feet is maintained between the two levels at all times (Crab Orchard Mine Technical Staff, 2017)."

Jan 1, 2019

By M. J. Raffaldi, L. A. Sandbak, K. K. Dehn, S. N. Warren, J. B. Seymour

"Confidence in the design and stability of an undercut cemented rockfill (CRF) span requires a thorough understanding of its emplaced material properties. The unconfined compressive strength (UCS) of cast 6×12-inch QA/QC cylinders is typically used as an index test to track the performance of a backfill plant. However, these strengths need to be adjusted for oversize aggregate removal and sample size effects if used to estimate the emplaced UCS. UCS testing of 6×12, 12×24, and 18×36-inch cast CRF cylinders was used to quantify the relationship between readily available 6×12-inch QA/QC strength data and the emplaced UCS. Test results indicate that the UCS of 18×36-inch cylinders is roughly 40% of the 6×12-inch UCS for similarly compacted samples. Mine QA/QC data indicate that the UCS of CRF is highly dependent on the degree of compaction as measured by bulk density. Based on these results, knowledge of the emplaced CRF density compared to 6×12-inch QA/QC density is also necessary to estimate the emplaced UCS. The scale effect reported in this study is more pronounced, compared to current understanding of backfill properties discussed in the literature, and underscores the need for further site-specific testing. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH) Spokane Mining Research Division (SRMD), in cooperation with Barrick Gold Corporation, is conducting research with the goal of determining a relationship between 6-inch QA/QC cylinder strengths and the in-place strength of cemented rockfill (CRF). CRF cylinders with dimensions (diameter × length) of 6×12, 12×24, and 18×36 inches were cast onsite at the Turquoise Ridge Joint Venture (TRJV) and Cortez Hills Underground (CHUG) mines using CRF mixed at the mines’ respective batch plants. UCS tests were performed after 28 days of curing to estimate the size correction factor for each mine’s CRF. This paper presents an overview of the mix designs, sample collections, testing methods, test results, and an estimate of the UCS size correction factor for CRF at these mines. BACKGROUND Underhand cut and fill mining methods utilizing cemented backfill are common in underground metal mines in the United States. These methods are advantageous for controlling weak or highly stressed rock mass conditions by creating an engineered material that can be placed in openings, forming a beam that provides a safe, stable back for the next undercut. Increased use of underhand methods in the last 30 years has greatly improved safety in many cut-and-fill mines. However, with the continual push for more efficient and cost effective mining, there is a need to thoroughly understand the geotechnical properties of cemented backfill to assist in designing safe, stable openings while optimizing costs and production schedules."

Jan 1, 2018

By S. S. Peng

High horizontal stress has been well recognized as a significant factor in roof control. It can adversely affect roof stability if the panel is designed improperly. Mining experience has shown that it can cause a cutter roof. The effects of high horizontal stress on roof stability depend on many factors such as magnitude and direction of the maximum principal horizontal stress, ratio of the maximum to minimum principal horizontal stress, structure and mechanical properties of the immediate roof and mining sequence. However, little is known about the intrinsic mechanism of high horizontal stress effect on roof stability except some conceptual explanations. In order to design a stable entry, the redistribution and concentration of high horizontal stress around the openings must be fully understood. Using the 3-D finite element analysis technique, this paper presents the redistribution and concentration of high horizontal stress field for a three-entry system with different orientations of horizontal stress. Based on the horizontal stress redistribution, possible roof failure for different orientations of horizontal stress is analyzed.

Jan 1, 1996