Search Documents

By Shawn P. Coughlin, Michael A. Schimmenti, Juan Leonardo Tello del Pino

"PROJECT OVERVIEWThe Sistema de Potabilización Área Norte project (Northern Area Purification System) was a major expansion of the potable water system in Buenos Aires Province, Argentina. The aim of the project was to transport and purify raw water from the Paraná River to provide potable water for five communities in the northern part of the province, benefitting up to two million inhabitants. The project was constructed by a joint venture of four South American contractors (“the JV”), and consisted of the following key components:• Treatment Plant: A 16 hectare area was cleared for the construction of a treatment plant to purify 900,000 m3/day of raw water from the Paraná River and distribute it to the surrounding communities.• Bored Tunnel: Nearly 15 km of 3.6 m inner diameter tunnel, ranging from 18 to 22 m below grade, was bored with two EPB tunnel boring machines to draw the raw water from the river. The TBMs started from a central launch shaft and proceeded in opposite directions: Cristina advanced northbound to the Paraná River Intake System, and Liliana advanced southbound to the new treatment plant.• Access & Ventilation Shafts: Five access shafts and eight ventilation shafts were installed along the length of the tunnel. The access shafts were designed to provide entry points for inspection and maintenance of the final tunnel. The five shafts consisted of: one central launch shaft in the middle of the tunnel alignment, one retrieval shaft at each end of the tunnel (Intake and Treatment Plant, respectively), and two intermediate shafts. The intermediate shafts were installed before the TBM passed, with a final liner to be installed afterwards. Access Shaft 3, the intermediate shaft located between the launch shaft and the treatment plant, experienced persistent leaks during initial excavation attempts."

Jan 1, 2016

The evaluation of Abandoned Mined Lands can involve the investigation of very large areas of land. Often, the locations of critical areas or impending problems are unknown, and are not easily identified from the surface. Microseismic monitoring has been demonstrated to be effective in identifying potential instabilities and active movement in mines from distances of several kilometers. By placing sensors in proximity to, or in contact with, a high acoustic conductance layer close to the mined zone, large areas can be monitored for potential problems with a minimum of sensors and drillholes. As part of a U.S. Bureau of Mines contract, a prototype system was developed to identify and locate potential instability problems over wide areas of land. Once a problem area has been located, the system can be used to analyze the type of the problem, its size, relative degree of instability, and potential for damage. Continued monitoring after application of remedial measures can effectively determine the efficacy of those measures.

Jan 1, 1993

By G. Hoffmeyer, I. Ream

"Several copper projects exclusively utilizing in-situ recovery methods are currently under development in Arizona. Favorable conditions for In-Situ Copper Recovery (ISCR) include a saturated orebody, fracture hosted mineralization, hydraulic conductivity sufficient to effectively inject and recover solutions using wells, and a relatively flat background hydraulic gradient. Safe operation of an ISCR project requires that the operator have the ability to induce and maintain localized hydraulic gradients, thereby controlling the movement of injected and recovered solutions. Benefits of ISCR include reduced initial capital, and a greatly reduced environmental footprint. THE ISCR METHOD EXPLAINED The method chosen to extract a mineral from a deposit is driven by characteristics such as its size, grade and depth of burial. Large lower grade deposits that require significant excavation to access using surface methods are potential candidates for in-situ recovery. ISCR may also be ideal for smaller deposits due to the lower initial capital. However, regardless of the size of the deposit, certain hydrogeologic conditions must be present for ISCR to be successful. In-situ recovery methods do not require excavations of rock from the surface or underground, resulting in a dramatic reduction in surface disturbance when compared to conventional mining. With the ISCR method, what is visible above ground is the processing plant, well heads, piping, process solution impoundments and evaporation ponds. There are no waste rock piles, tailings impoundments, leach pads, or impacts associated with blasting and hauling. Other benefits include reduced initial capital, reduced dust and noise, and lower water use. Early testing of the in-situ copper recovery method by Occidental on the Van Dyke deposit east of Phoenix and by Kennecott at Safford Arizona in the 1970s produced encouraging results, but the permitting regime for a large-scale operation was not yet in place. Additional testing and commercial application of in-situ copper recovery techniques have expanded since the 1980s, most commonly in conjunction with open pit or underground mining operations. For example, several operations in Arizona (San Manuel, Miami East and Tohono) have used in-situ techniques to extract additional copper following conventional mining from parts of the deposits adjacent to open pits or underground workings. Where the rock has been broken up by conventional methods, the method is called “in-place” leaching. The US government has also been involved in assessing in-situ techniques. For example, joint research was conducted by the US Bureau of Mines and industry on the Santa Cruz deposit in Arizona; and both federal and state agencies have been involved to establish the comprehensive permitting regime that exists today. Currently there are several projects in Arizona being evaluated as stand-alone ISCR operations."

Jan 1, 2016

By R. R. Cellan

There have not been many opportunities to date for comparison between laboratory and commercial neutralization rinse data. Homestake Mining Company's Santa Fe project is one such comparison. This paper discusses laboratory procedures and results from a 100' leach pad height simulation column neutralization rinse test and compares principal data with that achieved in actual commercial leach pad neutralization rinsing procedures. Principal comparisons include the rate of WAD cyanide neutralization, decrease in effluent pH, stabilization of dissolved silver and copper, and the quantity of dissolved gold recovered during rinsing.

Jan 1, 1996

By R. D. Hansen

This paper discusses the influence of frother type and dosage on recovery/selectivity in coal/sulfide mineral flotation as a function of particle size. It is shown that different frother structures do exhibit quite different but consistent performance characteristics depending on the underlying particle size ranges involved as well as the dosage levels of both the frother and collector. The data presented on existing commercial frothers end some new special purpose experimental frothers is used to illustrate some general operator guidelines on proper frother selection and use.

Jan 1, 1985

By W. Robert Power

Dimension stone includes a wide variety of natural materials that are put to an equally wide variety of uses. It is possible to classify dimension stone according to the end use to which the stone is put or according to the lithology of the stone. Both schemes are used by the United States Bureau of Mines in the annual Minerals Yearbook. The 1969 Yearbook lists 15 specific uses and has additional miscellaneous catagories. The same Yearbook lists five specific rock types or lithologies, and also includes a miscellaneous category. In a short presentation it would hardly be possible to list and define all these categories, much less discuss the evaluation of deposits with regard to all possible combinations. Besides, I am only slightly familiar with some of the uses and their requirements. I have therefore chosen to limit my remarks to some special problems in evaluating dimension stone that is to be cut and finished to specific sizes, tolerances, and finishes for use in buildings and some monuments. This use class is called cut stone in the Minerals Yearbook. In terms of dollar value it is the largest single use category. In 1969 the dollar value of cut stone was $29,122,000 which is more than twice the value of the next largest category. For those of you who are interested in other use applications of dimension stone I suggest that you start with recent articles by Bowles (1960), Currier (1960), and Barton (1968).

Jan 1, 1972

By William G. Pariseau

The purpose of this paper is to present a discussion of the various approaches that can be utilized in the study of mine subsidence phenomena. Attention is focused upon the rational selection and use of laboratory models. Broadly interpreted, mine subsidence is the deformation of the rock mass enclosing the mine. Depending upon a number of factors, the movement of the subsiding rock mass may be such as to disrupt gas and water lines or other buried utilities, to damage surface structures such as buildings and bridges, to dislocate streams, roads, and rail lines, to aggravate acid mine drainage and fire problems, and to generally mar the landscape. It is clearly a problem that no mine manager can safely ignore. It is also a problem that will grow with the general population increase. In the following, a summary review of past and present approaches to subsidence studies is given. The possibilities of duplicating subsidence phenomena in laboratory models are examined, and an analysis of a particular type of model is presented. Some preliminary results obtained from a model of the particular type analyzed are then discussed.

Jan 1, 1968

By E. Kenneth Siroky

The concept of ultrasonic measurement was originally applied to marine operations. Sonar . . . standing for Sounding, Navigation and Ranging, was developed for military uses. Today Sonar has become very important to the fishing fleets and marine construction industries where its applications cover a wide range of uses our company, in addition to the inair ultrasonic equipment as discussed in this paper, is also deeply involved in marine sonar and works primarily with oceanographic research and fishing industries. Ultrasonics, by simple definition, are sound waves beyond the audible range of the human ear and are generally accepted to be waves over 20,000 cycles per second. When applied to level measurement, the principles of ultrasonics are basically quite simple. A sound pulse is initiated at a point in time and the time interval for the echo from that pulse to return can be interpolated into distance. The speed of sound in air under standard conditions is approximately 1,100 feet per second, or if converted into more meaningful information as related to distance measurement, the time required for sound to travel one foot round trip is 1.78 milliseconds. An early application for ultrasonic level monitoring equipment was in large grain elevators. Prior to ultrasonics, the common practice of inventory measurement was to have an employee walk around the top of these large grain elevators, which are often over 100 feet above ground level, and drop a weighted rope or chain down into the silo to determine the level of the grain. Needless to say, this was a slow process and could be extremely unsafe, especially during windy and snowy weather conditions. An alternate

Jan 1, 1971

By D. A. King

Monitoring devices have been installed at several mine sites to assess the potential for the development of acid rock drainage (ARD) in waste rock, spent ore, and tailings material. In addition, instrumentation has been designed for monitoring changes in water quality in pit lakes. These devices monitor temperature, oxygen, water movement, and water chemistry in the waste rock pile. This information can be used to evaluate the current and future ARD risk, the effectiveness of caps and covers, and provide information to aid in the design of other reclamation strategies that limit ARD development. The instrumentation includes nested thermistors and oxygen sensing ports, neutron access tubes, heat dissipation units (HDUs), and lysimeters. Many of the monitoring devices can be linked to a datalogger and telemetry systems, enabling monitoring data to be downloaded from the office.

Jan 1, 1997

By S. S. Peng

To prevent mine floor heave, the mechanisms of floor heave must be fully understood. Based on the field study, the mechanisms of two types of floor heaves are analyzed in this paper. The mechanical models for the two types of floor heaves are developed. The floor heave can be predicted by the developed mechanical models and the control measures are recommended.

Jan 1, 1995

By Ali Ekrem Aritan

Exposure to hand-arm vibration (HAV) among the labor force in the mining industry can result in permanent vibration diseases such as behavioral disorders, visual impairment, osteoporosis, pain (mostly in the hands, wrists, and shoulders), circulatory system disorders, and malnutrition. In this study, the vibration exposure of excavator operators working regularly in 25 different natural stone quarries was measured. In addition, the relationship between vibration exposure and rock properties was investigated. Gloved and ungloved vibration measurements were performed and revealed that antivibration gloves reduce excavator operators’ vibration exposure by 7.10–25.95%. Samples from each quarry were characterized with rock mechanics tests. The correlations between the hand-arm vibration measurements and the natural stone physical–mechanical properties (uniaxial compressive strength, Shore hardness, Knoop hardness, apparent density and total porosity) were determined to be over 70%. One finding of the study was that the health risk in excavators cannot be reduced sufficiently by the sole use of antivibration gloves. Furthermore, the excavation of any rock with a Knoop hardness above 121 is associated with an 81% risk of HAV. To increase awareness of the danger of vibration exposure for natural stone miners, training programs should be provided, and technical and operational changes should be implemented.

By Peter Zhang, Daniel Su, Mark Van Dyke, Heather Dougherty

The integrity of shale gas wells in longwall chain pillars under the influence of longwall mining is a safety concern for both coal and gas operators. Previous modeling studies of gas wells in longwall pillars have shown that a FLAC3D model can predict longwall-induced stresses and deformations in gas well casings with reasonable accuracy. The predicted casing deformations can be verified by multi-finger caliper survey. This study concerns the influence of longwall mining on eight shale gas wells in a shale gas well pad located in the chain pillars between two adjacent longwall panels under 1,030 feet of cover. FLAC3D modeling was performed to predict longwall-induced deformations in gas well casings based on site-specific mining and geological conditions. Small deformations less than 0.5 in were predicted in the intermediate casing above 600 ft depth, and very small casing deformations less than 0.15 in were predicted below 600 ft due to high abutment pressure and high frictional resistance along the weak bedding interfaces. After the first panel was mined, a 56-arm caliper survey was performed on one of the wells to measure the longwall-induced casing deformations in the intermediate casing. The predicted casing deformations were then compared with the measured deformations, which indicated that the prediction was generally in good agreement with the measurement in terms of deformation locations and magnitudes. Findings from this study provide valuable information not only for stability assessment of shale gas wells in longwall chain pillars but also for developing engineering guidelines to preserve casing integrity through adequate pillar and casing design.

By Frank J. Klima

Explosives are probably the most widely used and most mysterious large scale' mining tools of modern times. The post black powder explosives were primarily nitroglycerin-based straight dynamites, ammonia dynamites, blasting gelatin, gelatin dynamites, ammonia gelatin dynamites, etc. Of these, the strongest and highest velocity explosive used in industrial operations is blasting gelatin, which is nitroglycerin colloided with a nitrocellulose of medium nitrogen content in proportions which give the product a plastic character, or about 93 to 7. Many variations of the basic groups above were developed by substituting ammonium nitrate and/or sodium nitrate for some of the nitroglycerin. The nitrates being insensitive to caps required a certain percentage of nitroglycerin to sustain detonation in smaller quantities or diameters. Paralleling the development of industrial dynamites was the development of more expensive, highly sophisticated explosives which were developed for specific military purposes. Such explosives as Amatol, RDX, Composition A, Composition B, Composition C, Lead Azide, PETN (Pentaerythritol Tetranitrate), Tetryl, Pentolite, TNT, etc., were primarily military explosives. Amatol, which is a cast mixture of ammonium nitrate and TNT (Trinitrotoluene), and identified by percentage of AN versus TNT as 50-50 Amatol, 80-20 Amatol, etc., was a favorite World War I explosive. RDX, or Cyclonite, was widely used in World War II. Also used during WW II were compositions A. B, and C, which were mixtures of RDX (Cyclotrimethylene trinitramine), TNT, and other nitrotoluenes. These high explosives, along with nitroglycerine, are exact chemical compositions or mixtures of exact chemical compositions which are individually explosive, or in other words, individually capable of explosive chemical decomposition when properly initiated. These chemical decompositions result in the formation of simpler compounds and/or large quantities of common combustion gases, and large amounts of energy in the form of heat. Of these, the most powerful is RDX which, based on the ballistic mortor test, is 1.5 times as powerful as TNT. Chemically, the decomposition of TNT releases about as much energy as the reaction of ammonium nitrate and fuel oil.

Jan 1, 1967

By K. Zhang

Real option value (ROV) method is considered to be more practical and advanced compared to net present value (NPV) method in evaluating a mining project, in particularly when there is substantial uncertainty in the commodity market as well as possible operational flexibility embedded in the project. Usually, it may take months or even years for the commodity product to be available in the market after the mining activation decision is made. The impacts of postponing the delivery of commodity product on the mine?s ROV and NPV are assessed based on the proposed real option method. Postponing the delivery of the products leads to declined NPV and ROV compared to the non-postponing scenario and extended postpone results in higher lost values in NPV and ROV. For a mine with lower mining cost, by postponing the delivery, the exercising threshold of commodity price is lower because the mine owner anticipates that commodity price may rise during the time of postponing. A mine with higher mining cost requires a higher exercising price threshold to ?lock up? the profit when there is ambiguity of market situation due to the postponing of the delivery.

Feb 23, 2014

By Arland R. Krueger

You have asked me today to tell you how quarried stone is meeting the challenges of contemporary architecture. The new position of stone, the oldest building material, in contemporary architecture, was described to me very concisely the other day by a very distinguished avant garde architect. He said rather wryly, "Do you know, if quarried stone had only just been discovered, we would all be calling it the most miraculous of all the modern miracle building materials." His prognosis was, I believe, much more than a witty quote. It echoes the surprise and. enthusiasm with which a considerable segment of the architectural profession is rediscovering stone as a most modern building material that offers unsurpassed values in beauty and practicality - well deserving of the term "miracle".

Jan 1, 1960

By M. Dayne Aldridge

A description is given of an experimental ventilation control system designed, built, and tested by WVU under United States Bureau of Mines sponsorship. A description is given of the control, system used and the mine-wide microcomputer-based ventilation monitoring system used with it. Test results of experiments conducted with this system at Eastern Associated Coal Corporation's Federal No. 2 underground coal mine are presented. In addition, a brief description is given of a new microprocessor based system presently being tested.

Jan 1, 1980

By A. P. Mehta

The role of microorganisms in the leaching of metal sulfides is well established (Torma, 1977; Murr, 1980). However, this established knowledge applies mostly to chemolithotropic microorganisms such as Thiobacillus ferrooxidans which function optimally in leaching catalysis between 25-35° C, and in a pH range of 2-2.5. Although leaching with thermophilic microorganisms capable of extending the range of catalytic viability beyond 35° C is also documented, there are few if any attempts to optimize or extend sulfide concentrate leaching with thermophilic microorganisms. When mixed metal sulfides or other materials having different rest potentials (referenced to the standard hydrogen electrode, SHE, in the electromotive series) make contact in a conducting, aqueous medium, the contacting members will act as an electrochemical cell, with the member having the higher rest potential assuming the role of an electrical cathode. In leaching reactions involving such galvanic couples, the cathode becomes passivated, while the anodic member reacts vigorously due to the electro- chemical reaction which occurs (Hiskey and Wads- worth, 1975). Serry, eta1 (1978) observed that when chalcopyrite and pyrite were in intimate contact in natural ores, the chalcopyrite reacted vigorously by galvanic conversion as a result of the higher rest potential (~ 0.63 V) as compared to the chalcopyrite (~ 0.53 V). In addition, it was postulated that because of the elemental sulfur which can form on the anodic chalcopyrite in this galvanic conversion process, reactions in acid-bacterial medium would be expected to have accelerated copper extraction because of the conversion of any sulfur product layer on the chalcopyrite anode to sulfuric acid according to the following general reactions: [MS?M2+ + S° + 2e- (1) and 2S° + 302 + 2H20 bacteria?-2H2SO 4 (2)] where M in reaction (1) designates the metal (or metals in the specific case of chalcopyrite) to be released to solution by galvanic conversion.

Jan 1, 1982

By S. Alpay

Underground mining method selection (UMMS) is one of the most important decisions that mining engineers have to make. Choosing a suitable underground mining method to extract a mineral deposit is very important in terms of economics, safety and productivity of mining operations. In real life, UMMS is one of the Multiple Attribute Decision Making (MADM) problems and decision makers have always some difficulties in making the right decision in the multiple criteria environment. Analytic Hierarchy Process (AHP) and Fuzzy MADM (FMADM) are the MADM tools and can be used for the selection of the best underground mining method by considering the problem criteria. UMMSMADM is a computer program which is based on AHP and FMADM and it can analyze the UMMS problems and produce the best underground mining method considering different deposit shapes and ore bodies.

Jan 1, 2010

By J. P. Ducarme, J. L. Carr, C. C. Jobes

"An average of 1.2 fatalities occur per year in underground coal mines in the United States when a miner is struck or pinned by a remote-controlled continuous mining machine. Proximity detection technology provides a means to prevent these types of accidents by disabling all machine motion when a miner is in close proximity. Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed the intelligent Proximity Detection (iPD) system, which continuously tracks the position of miners near the machine and disables only those machine motions that could cause a pinning accident. This system, previously demonstrated using non-permissible proximity detection hardware, has now been shown to be effective when implemented using an MSHA-approved system as a platform. Performance tests have shown accuracy, repeatability, and stop zone identification to be comparable to or better than the system demonstrated with non-permissible hardware. INTRODUCTION Underground coal mining room-and-pillar operations typically use Continuous Mining Machines (CMMs), such as the one shown in Figure 1. When CMMs first became available, they were operated from an on-board operator’s compartment that protected operators from roof falls and other hazards but severely restricted visibility and subjected them to machine vibration and high levels of dust and noise. To solve these problems, remote controls were developed to operate CMMs. Now CMM operators are free to position themselves for best visibility of each mining task and are no longer subjected to the rough motion of the CMM during mining operations or the dust and noise generated by the machine. However, this technological advance removed operators from the protection afforded by the operator’s compartment and exposed them to the hazard of being struck or pinned by the CMM or other large moving machines."

Jan 1, 2015

By William W. Edgerton

Establishing geotechnical baselines on soft ground projects that require the use of closed-face tunnel boring machines (TBMs) is difficult. It is hard to see the face when mining and the excavated material is combined and mixed, all of which makes baseline quantifications challenging. In an attempt to meet underlying objectives of minimizing bidder contingencies, allocating or sharing risks and paying for conditions only if they occur, nongeotechnical baselines (i.e., functional baselines) have been developed. These have been used on the District of Columbia Water and Sewer Authority?s Clean Rivers (DCCR) Blue Plains Tunnel (BPT) project. This article examines the development of such functional baselines and how they were implemented on the BPT project.

Jan 1, 2012