Search Documents

By M. Raffaldi, J. Johnson, M. Stepan, D. Benton

"The Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD), is continuing its High-Energy High-Displacement (HEHD) testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement, and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link fence, welded-wire mesh, and combinations of these products. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can be used by the practicing engineer to evaluate installed support based on visual observation of cracking and deformation. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to quantify the stability of installed shotcrete support. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD) is continuing research on the behavior of shotcrete when used as the surface support component in mining ground support systems. Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often used to accomplish this (Figure 1). Maintaining support pressure during ground deformation is key to the performance of these systems, and to ensuring miner safety. However, the toughness of a ground support system–the ability to maintain strength over large deformations–is difficult to quantify. Researchers at SMRD have responded to this deficiency by designing a full-scale test device, described previously by Martin et al. [2015a], and beginning a testing program to assess the behavior of shotcrete surface support reinforced with a variety of products including: fibers, chain-link mesh, welded-wire mesh, spray-on polyurea liners, and combinations of these products. This paper presents the findings of these tests."

Jan 1, 2016

By M. Raffaldi, J. Johnson, M. Stepan, D. Benton

"The Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD), is continuing its High-Energy High-Displacement (HEHD) testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement, and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link fence, welded-wire mesh, and combinations of these products. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can be used by the practicing engineer to evaluate installed support based on visual observation of cracking and deformation. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to quantify the stability of installed shotcrete support. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD) is continuing research on the behavior of shotcrete when used as the surface support component in mining ground support systems. Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often used to accomplish this (see Figure 1). Maintaining support pressure during ground deformation is key to the performance of these systems, and to ensuring miner safety. However, the toughness of a ground support system–the ability to maintain strength over large deformations–is difficult to quantify. Researchers at SMRD have responded to this deficiency by designing a full-scale test device, described previously by Martin et al. [2015a], and beginning a testing program to assess the behavior of shotcrete surface support reinforced with a variety of products including: fibers, chain-link mesh, welded-wire mesh, spray-on polyurea liners, and combinations of these products. This paper presents the findings of these tests."

Jan 1, 2016

By Judson H. Whitman

To evaluate intelligently and to market a source of rare earth raw material, it is necessary that the producer understand the requirements of the processor and the manner in which these requirements effect the value and salability of his product. This paper will be an attempt to aid in such an understanding. The majority of rare earth processors are primarily chemical companies, not mining or metallurgical companies, as the complexities of the processing procedures are' much more chemical in nature than metallurgical. The rare earths and the rare earth industry are normally divided into two groups - the ?light? or cerium group and the ?heavy? or yttrium group. They are so named because cerium and yttrium are the most common elements in 'heir respective groups and are so divided on the basis of mineralogical and chemical characteristics. The dividing line of the two groups is not rigidly fixed but usually is considered as being between samarium (atomic number 62) and europium (atomic number 63). Although the two groups are quite similar, processing procedures differ significantly, hence most processors tend to specialize in one group or the other. There is, however, a growing tendency toward participation in both groups.

Jan 1, 1960

By R. Bishop, J. Baggett, J. Monsalve, J. Hole, N. Ripepi, A. Abassi

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karsts are complex and challenging ground control risks. Traditional methods of predicting karst locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features. Ground penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in material properties between limestone and open karsts causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries, however there is a lack of published research on underground mining GPR applications. The purpose of this work is to prove the viability of GPR in underground stone mines for karst detection, and to discuss the importance of karst detection ahead of mining. INTRODUCTION The Mine Safety and Health Administration (MSHA) currently lists 116 active underground stone mines in the United States, the vast majority of which extract limestone for crushed stone products. These limestone mines have the potential to encounter karst voids at some point in their operation, as most karstic regions of the United States develop in limestone rock masses (Kuniansky, Weary, & Kaufmann, 2016). Karsts, the cavities formed by the dissolution of carbonate rock, have long plagued the mining and tunneling industries, as well as been a hindrance on the Earth’s surface, producing sinkholes and ruining otherwise valuable land for construction and public use. The impact of karsts on the Gavarres tunnel in Spain is well documented by Alija et al; constant instability conditions, material spills into the tunnel, and unexpected cavities seriously delayed the project deadlines and “were not foreseen in the design” (Alija, Torrijo, & Qunita-Ferreira, 2013). At the water supply project in Sohngua River, China, Bin et al detail the presence of both water and sediment filled karsts which are sources of disastrous conditions at this tunnel (Bin, et al., 2017). A hydrological tunnel in Lebanon encountered numerous massive karsts in the tunneling path which required remediation via friction anchors, rockbolts, welded wire fabric, channel steel arch segments, invert steel beams, and shotcrete (Leech, Jaoude, & Ghanem, 2008). From a design standpoint, rock mass classification schemes, such as the RMR from Bieniawski and the Q-system from Barton, are not able to represent the true nature of a karstified carbonate rock mass, and therefore complex case-by-case analyses of underground conditions are necessary (Andriani & Parise, 2017).

Jan 1, 2019

By Brandon Barnes, Michael Haggerty

"Around Minneapolis and Saint Paul, Minnesota, the local geology includes the St. Peter Sandstone, which is easily minable and has facilitated construction of interceptor tunnels for storm water and sanitary tunnels since the 1800s. The elevation of the geologic units allowed gravity-driven flows from the downtown areas all the way to the Mississippi River. Through many years of service, some of these tunnels have experienced degradation and require maintenance. Additionally, increased stormwater surface runoff can result in internal pressurization of the tunnels, accelerating degradation. Because structural failure or collapse of any of these interceptor tunnels would create a significant repair challenge, the city of Minneapolis has been inspecting and designating tunnels in its system for periodic review and repair. One of these, the St. Mary’s/Hiawatha tunnel, was rehabilitated using a grouting program. A hydrologic model was also used to improve understanding of pressurization events during some storms, leading to construction of a near-surface pressure dissipation chamber to provide increased hydraulic capacity. BACKGROUND The St. Mary’s/Hiawatha tunnel in Minneapolis has three segments; the first two were constructed in 1942 and the third was added in 1987 (Figure 1). Segment 1 is approximately 4,700 feet in length and outlets to the Mississippi River. Segment 2 intersects Segment 1 approximately 3,500 feet upstream of the river outlet and continues for approximately 2,500 feet in a southeasterly direction. The third and newest segment is approximately 500 feet long. There are four different cross sections of tunnel along the entire system.Originally, tunnel construction often consisted of mining the St. Peter sandstone with a pressurized water lance and constructing wood lagging support (Payne, 1967). An underdrain was generally installed below the invert during construction; this resulted in localized dewatering and provided groundwater control during construction. Non-reinforced concrete liner sections were cast in place. Often void space existed between the tunnel liner and the native sandstone bedrock. These voids, particularly in the crown, prevent direct contact between the liner and the bedrock."

Jan 1, 2016

Underground instrumentation and observations at longwall panels have demonstrated that the growth of main roof causes an extremely high roof weighting on the shields. It can sometimes result in catastrophic effects on the support when the roof weighting intensity far exceeds the support capacity. In this paper, a comprehensive study was conducted on characteristics of main roof breakage and its effects on shields at different locations, based on the monitored shield data, theoretical analysis, and finite element analysis. With the help of theoretical analysis and numerical modeling, stress distribution and redistribution in the main roof were analyzed in detail to define main roof failure modes and understand the maximum roof weighting intensity imposed on the shields. From this study, it was found that the effects of main roof breakage on shields are chiefly related to the shield initial setting condition and the final failure mode of the main roof.

Jan 1, 1994

By Mustafa Kumral, Yuksel Asli Sari

Economic evaluations of underground mining operations are made based on the estimated or simulated grades of the block model as the actual values are not known. Depending on how the planning decisions are made, the risk of the operation can be managed and decreased. This research introduces a mixed-integer linear programming (MILP) model for stope sequencing optimization that considers the uncertainty associated with net present value (NPV) using chance-constrained programming (CCP). The introduced method permits achieving a balance between maximizing NPV and reducing the associated operational risk through transforming the problem into a multiobjective problem, where the objectives are maximizing the NPV and minimizing the risk. This risk is expressed in terms of the standard deviation of project outcomes, taking into account multiple possible scenarios. In a case study, the efficiency of the method was demonstrated as a decision-making tool capable of translating a specified risk or reliability level into a stope sequencing plan.

Jan 1, 2024

By John W. Crawford

The title of the paper which I have been asked to present is somewhat misleading it infers in fact that there is a definite coalbed height below which raps or canopies cannot be applied to electric face equipment. Although this may be so with regard to certain pieces of existing equipment under certain conditions, to date we do not have enough experience to determine this magic number. Therefore MESA is continuing to hold the line on the time frames stipulated in Section 75.1710-1 of the Mandatory Safety Standards - Underground Coal Mines, which at this point in time requires these protective structures in mining heights of 60 inches or more. In order to give you an idea why we are taking such a firm stand on this matter, I believe it is necessary to describe some of the background work that was done prior to promulgation of the regulations and to give a resume of our experience since the requirements have become effective. Initially MESA made field investigations of all underground mines to determine what the state of the art was in the use of cabs and canopies for protecting equip¬ment operators from falls of roof. These studies revealed that the application was basically in its infancy and what progress had been made was due to the impetus of the mine operators themselves. Manufacturers of electric face equip¬ment provided these structures only on the direct order from the mining company and built them to their specifications. In talking to the operators and the miners in mines where cabs or canopies were in use, it was the consensus that these structures did improve safety and that although originally there was some reluctance on the part; of the miners to work in the confines of a cab or canopy, mast would not work without them once they had been adapted to the equipment.

Jan 1, 1975

By E. L. Piper

Natural graphite has been known for many centuries, having first been reported as a distinct mineral form by Gessner in 1565. At that time, graphite was used extensively as pencil "lead" because of the ease with which it marks paper. It is a black, unctuous material found as flakes, lumps, or needles in scattered locations throughout the world. The less crystalline, or "amorphous", natural graphites are thought to have been formed from coal under conditions of high temperature and pressure. The more crystalline varieties, such as those mined in Ceylon, probably were precipitated from molten solutions or were pyrolyzed from gaseous carbon compounds. Recognition of the good thermal and electrical conductivity of graphite, together with its highly refractory nature, led to an increasing number of appli¬cations for this material. Clay and pitch bonded natural graphite has been used in crucibles, refractories, foundry facings, and other high-temperature appli¬cations. These forms constitute the most important current uses for natural graphite in the United States. Other products containing natural graphite include batteries, lubricants, pencils, brake linings, etc.

Jan 1, 1973

By Tony Dunn

FMC Corp. achieved a significant cost reduction at its Green River, WY soda ash operations using a new proprietary solution-mining and processing technology. In phase one of the program, trona ore is dissolved, recovered and processed with the new technology. It is then fed into an existing refining plant, replacing dry mined and calcined trona ore. Phase two produces a final high-purity product. It also increases capacity by 635 kt/a (700,000 stpy). Both phases were completed under budget and ahead of schedule. This $120-million expansion project uses a new process and a new team to derive soda ash in a more cost-effective and environmentally friendly manner. The team successfully introduced solution-mining technology - with a liquid solution injected into previously mined sections of the mine. This shift in techniques signified a new era for soda ash production. The project is an example of teamwork at its best. For it to be successful, FMC had to work within several different areas inside and outside of the company. Engineers, contractors, mechanical operators and technical people were needed who could blend in with FMC's existing in-house team.

Jan 1, 1999

By Robert J. Henning

The term olivine was first used in 1790 by J. Werner, and the corresponding mineral was so named because of its olive-green color (Hunter, 1941). Olivine is the principal component of the rock known as dunite. While by classic definition dunite is composed of 90% or more olivine, commercial use of these terms has resulted in more specific definitions. Commercially, the term olivine is used to designate a material that consists of 85% or more forsterite and contains 45 to 50% MgO, 39 to 42% SiO2, 5 to 8% Fe2O3, and has an ignition loss (LOI) of 1 to 2%. The term dunite designates a rock that contains 36 to 45% MgO, 36 to 39% SiO2, and has an ignition loss of as much as 10% (Teague, 1983). GEOLOGY Olivine is found in basic igneous and basic metamorphic rocks whose age varies from pre-Ordovician to Tertiary. Economic deposits are of magmatic origin and are restricted to the dunite variety of the peridotite group of ultrabasic igneous rocks. Olivine also occurs in basic igneous rocks such as gabbro, basalt, and diabase and more rarely as an accessory mineral in granite and metamorphosed crystalline limestones. Mineralogy The term olivine refers to a group of orthosilicate minerals in isomorphous series with magnesium-rich forsterite (Mg2Si04) as one end member and iron-rich fayalite (Fe,SiO,) as the other. In most olivines the ratio of magnesium to iron varies from 16: 1 to 2: 1. Commercial olivine deposits contain a mixture of forsterite and fayalite with the fayalite content restricted to less than 15% (Reed, 1959; Teague, 1983). Accessory constituents may include primary minerals such as ilmenite, magnetite, diopside, chromite, and garnet and secondary minerals such as chlorite, serpentine, talc, and vermiculite as alteration products. Chemical and Physical Properties The chemical composition of olivine can be expressed as either (Mg, Fe), SiO, or 2(Mg, Fe)O.SiO,. Table 1 presents chemical analyses for some commercial olivines. The physical properties of olivine are shown in Table 2. Distribution of Major Deposits Commercial olivine and dunite deposits are found in Norway, Japan, Spain, India, Italy, the United States, Sweden, Austria, Pakistan, and Mexico. Noncommercial deposits have been reported in New Zealand, Zimbabwe, South Africa, New Caledonia, Greece, Brazil, and Canada (Teague, 1983). The present markets for olivine are characterized by low unit value, high volume, and high sensitivity to freight costs, so few deposits are commercially viable. Literature from the USSR indicates that considerable research on olivine refractories is being done. (Afansa'ev, 1988), lending credibility to the conjecture that commercial deposits are being mined there. In eastern Canada synthetic olivine is being produced by calcining chrysotile asbestos mine tailings. In the United States numerous lenses of olivine extend in a belt from northeast Georgia northeastward across western North Carolina. Total reserves in North Carolina and Georgia are estimated at between 125 and 200 Mt. The largest US deposit is Twin Sisters Mountain, located in Whatcom and Skagit Counties in the state of Washington. This deposit, which has an outcrop area of 93 km2 and a relief of about 1 525 m. is estimated to contain 1 800 Mt of fresh, unaltered olivine (Teague, 1983). In addition, the US Bureau of Mines reports reserves of 50 Mt on Cypress Island in the state of Washington, and the literature reports eight complexes in southeastern Alaska, some containing cores of olivine as large as 1.6 km in diameter (Taylor, Jr., 1967). The world's largest deposit of olivine occurs in the Aaheim area of Norway, where reserves are estimated at a 2 000 Mt. Several other Norwegian deposits contain as much as 5 Mt each. In Japan the production of ultrabasic rocks is currently about 6 Mtpy, but the bulk of this output is serpentinite. Olivineldunite accounts for only 17% of this production. The major olivine deposit in Japan is located at Horoman Hill on the northern island of Hokkaido. Reserves at this deposit are estimated at 100 Mt (Anon., 1990). Spain is one of the largest producers of dunite. Reserves in the La Coruna District in northwestern Spain are estimated at 100 Mt. India, also a major dunite producer, has a large deposit at Salem in Tamil Nadu. In Italy olivine/dunite is mined from a deposit near Turin. In Sweden the largest deposit is at Arutats and is reported to be comparable in size to the Twin Sisters deposit in the United States. At present the only production in Sweden is from a deposit 30 km south of the town of Gallivare. Reserves at this deposit are reported to be between 1 and 2 Mt. Other significant deposits are: 1) in Austria at St. Stefan near Leoben, 2) in the Swat District of the North West Frontier Province in Pakistan, and 3) in Mexico at Cuidad Victoria in Tamaulipas (Anon., 1990).

Jan 1, 1994

By M. S. Celik

Beneficiation of boron minerals by flotation with well defined systems has been very little investigated in the literature. The difficulty arises from the fact that boron minerals cover a spectrum of solubilities. Colemanite, a calcium containing relatively insoluble boron mineral, and borax, a highly soluble boron mineral have been used to exemplify the flotation of boron minerals. The floatability of both minerals using sodium dodecylsulfonate and dodecylamine hydrochloride exhibits considerable differences in their response to flotation. This has been ascribed to variations in the solubilities 0f boron minerals and the presence of the cations in the lattice structure. Flotation tests along with zeta potential measurements are used to elucidate the mechanisms involved in the flotation of boron minerals.

Jan 1, 1992

By A. Vien

A major thrust in Industrial automation over the past few years has been the exploration and incorporation of higher level (supervisory and optimizing) control strategies aimed at more fully exploiting the existing control system infrastructure. There is little doubt that this is worthwhile pursuit, however, one must not lose sight of the maintenance and development requirements of the basic control system. Statistics on loop performance indicate that this too is an area of considerable potential. In this paper the authors look at some of the less elegant, but arguably equally important issues in mineral processing plant control. The focus is on controller structures, loop tuning, sampling, filtering, and some of the other principal components of the regulatory control foundations. In many cases significant improvements In control performance can be achieved by getting back to the basics.

Jan 1, 1998

By Ihsan Berk Tulu, Ted Klemetti, Deniz Tuncay

Accurately estimating load distributions and ground responses around underground openings plays a significant role in the safety of the operations in underground mines. Adequately designing pillars and other support measures relies highly on the accurate assessment of the mining-induced loads, as well as the load-bearing capacities of the supports. There are various methods that can be used to approximate mining-induced loads in stratified rock masses, both empirical and numerical. In this study, the numerical modeling approach recently developed at West Virginia University, which is based on the modeling approach developed by the National Institute for Occupational Safety and Health (NIOSH), is investigated using the finite difference software FLAC3D. The model includes the longwall panels, the adjacent chain pillar systems, and the different stratigraphic layers of the overburden. Using the 3D model, changes in loading conditions and deformations on the areas of interest, induced by an approaching longwall face, can be examined. This paper details the 3D modeling of a longwall panel utilizing this approach, and the verification of the results against field observations. The studied panel was 360 m wide with a 3-entry chain pillar system and about a 160-m average overburden depth around the studied area. The overburden strata consist of alternating layers of shale, sandstone, and limestone. The FLAC3D results were compared against field measurements from the mine site. The stress change values measured in the chain pillars were comparable with the modeling results. The model also replicated the surface subsidence profile obtained from field measurements fairly well. Overall, the 3D modeling approach was found to be successful for the case study longwall panel.

Sep 23, 2020

By M. J. Virnig, Marc Le Vier, Rong Yu Wan, Jan D. Miller

Although most gold production from primary resources is achieved by cyanidation, many research activities have focused on alternative processes using noncyanide lixiviants. Such research has been prompted by environmental concerns and problems associated with the processing of refractory gold ores. Numerous research projects have been conducted to search for a noncyanide hydrometallurgical process for gold extraction. In this paper, a technical review of gold recovery from noncyanide solutions is presented, and new results are reported. Gold recovery techniques that are considered include activated carbon adsorption, cementation, solvent extraction, ion exchange, and reduction-precipitation.

Jan 1, 1993

By Norman F. Schulz

The Davis magnetic tube concentrator is a laboratory machine designed to separate a small sample of pulverized magnetic iron ore into magnetic and non-magnetic fractions. It was developed in 1921 by mechanization of a test previously performed manually. (1)(2)(3)(1) No significant changes have been made in the design of the apparatus since that time. The Davis magnetic tube test continues to serve as a practical basis for judging the amenability of an ore to magnetic separation and for controlling magnetic separation plant operations. The apparatus consists of an inclined cylindrical glass tube supported adjacent to closely spaced pointed poles of a powerful C-magnet. (Figure 1). To conduct a tube test, a sample of a suitably prepared ore is poured into the water-filled tube. With wash water flowing through, the tube is oscillated to gradually reject the weakly magnetic ore particles until the desired degree of separation is attained. Both the magnetic concentrate and the tailings may be recovered for examination.

Jan 1, 1963

By Erica McGlynn, Brian Negrea, Lance Jackson

There was no need for the people of Cleveland to ask “Where does the raw sewage go? We want to know!” because it was clear. The raw sewage was being discharged into Lake Erie during heavy rainfall events due to the outdated design of the combined sewer system. In efforts to resolve this ongoing issue for the City of Cleveland, the Northeast Ohio Regional Sewer District developed Project Clean Lake in collaboration with the US EPA. Project Clean Lake is a 25-year, $3 billion program consisting of seven large-diameter CSO storage tunnels to be constructed beneath the city’s existing infrastructure. The first four tunnels have been completed using traditional hard rock TBM excavation methods. The fifth tunnel, the Shoreline Storage Tunnel Project, presents unique challenges and complexities as it will be the first large-diameter EPB TBM to dig under the City of Cleveland. The project itself consists of one tunnel drive 14,100' (2.7 miles) in length, two pipe jacking tunnels, three large slurry wall shafts, two diversion structures, and three regulator reconstructions. Upon completion of the project, 12 permitted CSO locations along Lake Erie will be taken offline, reducing overflow volumes by approximately 350 million gallons per year. This paper will discuss the current status of construction and the chosen means and methods, including the myriad of nuanced differences between hard rock and EPB TBM tunneling methods. Particular attention will be given to the site preparation, setup, and organization; TBM assembly; and TBM launching practices.

Jun 13, 2023

By Cancelli Paolo, Bragonzi Gianluca, Pelizza Sebastiano

"In May 2015 the New Monte Bianco aerial cableway, operating on the Italian side, have been completed. It connects the lower station in Pontal d’Entreves (1300 metres above sea level (m a.s.l.)) with the intermediate station at Pavillon de Mont Frety (2160 m a.s.l.) and with the top station at Helbronner Peak (3460 m a.s.l.). A new underground link between Helbronner Peak and New Torino Refuge has also been built. The link is divided into two different sections: the first one, a 70 meters deep vertical pit created using the “Raise Boring”, descends underground from Helbronner Peak station; the second section, a 160 meters long sub horizontal tunnel, emerges at Torino Refuge. After a first introduction focused on the general layout of the project, the paper will present the geomechanical survey aimed to evaluate the effect of permafrost on the stability of intensely fractured granitic mass. Finally, it will describe the relevant issues related to the highest construction yard in Europe (3400 m a.s.l.): difficult conditions such as extremely cold and windy weather and restricted spaces. INTRODUCTION The new cable way connects the lower station in Pontal d’Entreves (1300 m a.s.l.), close to Courmayeur, with the top station at Helbronner Peak (3462 m a.s.l.) and its territory, as well as links with France and, through the French territory, with the town of Chamonix (1000 m a.s.l.). The overall layout is divided into two sections (as shown in Figure 1): the first section, “Pontal d’Entreves – Mont Frety”, has a length of 1700m, elevation differential of 886m, a capacity of 800 persons/hour and cable cars for 80 passengers; the second one, “Mont Frety – Punta Helbronner”, has a length of 2630m, elevation differential of 1276m, a capacity of 600 persons/hour, and cable cars for 75 passengers. The new system is designed for fully rotating cable cars moving at a constant rate of 9.0 m/s. The track requires constructing special cables supports, three for the first section and two for the second one."

Jan 1, 2016

By Lee R. Martin, Michael R. Taber

Bird Balls™, the latest development in the ongoing battle at mine sites across North America, help to eliminate accidental avian mortality caused by birds ingesting cyanide leachate. Bird Balls™ are a 4-inch sphere made of high-density polyeth­ ylene (HDPE). They weigh 40 grams and are black in color to provide optimum life in UV intense environments. A floating blanket of bird balls totally excludes birds from a liquid surface. Federal agencies that enforce the Migratory Bird Treaty Act do not specify how to keep migratory birds out of leachate basins. Some state agencies, however, specify that a physical barrier must be in place to exclude migratory birds if cyanide levels are high enough to cause mortality. Industry standards for protecting waterfowl now include Bird Balls™ as well as net­ting, detoxification, and heap leach systems designed in such a manner that no exposed solution ponds or channels exist. Hazing is no longer an option. A bold statement to make? Perhaps, but W. R. Jeffress (1990) covers the subject well when he stated that, "Hazing techniques as a whole have not been effective in excluding waterfowl or other species of wildlife from toxic heap leach solution ponds or tailings impoundments. Research and devel­opment of the new 'Star Wars' hazing techniques, such as laser netting and radar systems, are interesting concepts and will pos­sibly offer an alternative to total physical exclusion or neutral­ization in the future. All of these methods are going to have to be thoroughly tested." For those who may want further docu­mentation, we have included a special reference section cover­ing hazing. R. J. Hallock (1990) stated that, "The Fish and Wildlife Service is particularly interested in migratory birds. In fact, a large portion of our effort, nationwide, is focused on migratory birds. Bird habitats are managed directly through the National Wildlife Refuge System and indirectly through other agency programs. We also have a responsibility to protect birds under the Migratory Bird Treaty Act. Most birds attracted to mine ponds are covered under this Act. The only migratory birds not protected under the Migratory Bird Treaty Act are English Sparrows, Starlings, and Pigeons. Since this is a treaty with five nations, the concept of acceptable losses does not apply. It is not a negotiable situation. There are a few exceptions noted in the Act, including prescribed hunting of selected waterfowl, scien­tific collection, and game bird farming. There is no exception for the loss of migratory birds exposed to solutions of cyanide."

Jan 1, 1996

By P. Geoffrey Feiss

The Piedmont province of the southern Appalachians is becoming the focus of interest for many exploration geologists. In the past, only those deposits with significant surface exposure have been exploited. Thus, few deposits have been found and relatively little exploration has been conducted in recent years. Modern geochemical and geophysical techniques can alleviate this problem of concentrating on exposed ore bodies by allowing us to "look through" the soil and saprolite to detect the presence of significant mineralization at depth. This paper will attempt to evaluate the feasibility and effectiveness of several geo¬chemical exploration techniques in the Piedmont, of Cabarrus and Stanly Counties, North Carolina. The area chosen for the study is shown in Figure 1, lying almost wholly within the Mt. Pleasant quadrangle, North Carolina. The area is on the eastern boundary between the Charlotte belt, a zone of plutonic and intermediate grade metamorphic rocks, and the Carolina Slate belt, a series of complexly interbedded volcanic and sedimentary rocks of predominantly low grade metamorphism. The area is now considered to be a 500 million year old active, continental margin.1 As is typical of most of the piedmont, outcrop is sparse. Figure 2 is a sketch map of the general geology of the area under study, showing the Charlotte belt rocks in the northwestern quadrant and slate belt rocks, to the east. Within the area are a number of old mines and prospects, the most famous of which are the Furniss and the Phoenix mines in Cabarrus County. All are reported to have contained Au and Cu. Ag and Pb were reported from some. A summary of the deposits is given in Table 1. Data used in this study are from three Master's theses conducted at the University of North Carolina at Chapel Hill. 3,3,6 In separate studies, well waters5, B-zone soils3, and vein and float quartz6 from the area described were sampled and analyzed. Each study concluded separately that geochemical anomalies in the vicinity of the ores justify use of that specific sample type in a geo-chemical exploration program. However, no comparative study of the methods has

Jan 1, 1977