Search Documents

By H. Walqui

The Empire concentrator currently processes magnetite ore from the Empire pit which is approaching the end of its mine life. Over the past two years plant wide tests have been run to access the plant capability of processing ore from the neighboring sister Magnetite pit. The neighboring pit presents challenges to the Empire plant due to its higher feed grade, finer liberation size and higher percent silica which require additional secondary grinding and concentrating capacity to achieve concentrate grade. The following paper summarizes the results from the second full scale test, run during 2009 under a challenging market environment

Jan 1, 2010

By M. J. Hart

There are no formulas that guarantee success when it comes to obtaining zoning approval for mineral aggregate mining. Local land use decisions often times represent the most controversial issues faced by community. Public awareness, concern, willingness to get involved, sensitivity to the environment and probably most importantly fear of change only begin to describe the atmosphere in which local land use decisions are made. Add to this the public hearing process which is quasi judicial, adversarial, and unfortunately not designed for resolution of disputes and it is not difficult to see the need for an alternative to present methods. Hopefully, some day we will have a process that will do away with or at least minimize unnecessary, unproductive and unmanageable community conflicts.

Jan 1, 1984

By John Hanna

Over the years the coal industry in Alabama has generated about 150 million tons of fine waste coal, increasing at a rate of 2 million tons/year, during mining and cleaning operations. Reclamation of the fine-size wastes containing 20-60% by weight clean coal provides, free of charge, mined and crushed feedstocks for coal recovery and eliminates a major source of acid water pollution. Tests were made on the impounded wastes and current plant discharges to recover the coal fraction by sizing, gravity and flotation techniques. Gravity separation of the plus 100 mesh material produced commercial grade coal averaging 8.2% ash, 0.8% sulfur and 13,350 Btu/lb. However, the coal recovery was relatively low at 50-65%. Froth flotation using mechanical and froth column methods gave similar coal products at much higher coal recovery of 87-93%. The coal produced analyzed 10% ash and 1.1% sulfur.

Jan 1, 1991

By A. G. Journel

The indicator random function formalism allows a common coding of hard numerical data, constraint intervals, and soft qualitative information as prior probability distributions. The soft kriging algorithm allows interpolating these priors into posterior probability distributions of the unknown. The curse of ?negative kriged grades? is solved. The consideration of additional soft information, whenever deemed necessary, becomes possible within the framework of well-proven kriging techniques.

Jan 1, 1986

By Dae Young Kim, Sim Bo Kyung, Ebrahim Farrokh, Ki Chang Hyun

"TBM cutter life evaluation in abrasive granitic rocks is a very important issue, especially in pressurized face tunneling with mixshield TBM for which the planning of costly interventions becomes crucial. This paper presents an overview of methodologies for cutter life evaluation in rock. A comparative study is performed to indicate the predictability of cutter life evaluation methods based on detail data from the NS3 tunnel project in Singapore. A new model is developed based upon the cutter wear information of eight TBM tunnels from around the world. New methods are proposed to evaluate the optimum intervention interval length and the number of worn-out disc cutters for a tunnel project. Finally, two new laboratory tests in the evaluation of disc cutter abrasion, including a full-scale and a small-scale test, are introduced, and their test results are discussed. INTRODUCTION The issue of wear evaluation for hard rocks has been extensively studied in drilling and pavement industry. In this regard, several tests and evaluation methods have been proposed to estimate or evaluate the state of tool life (e.g. bit life for drilling). In the case of TBM tunneling, tool wear may depend on several factors such as mineral composition, strength, or type of cutting, but as the abrasion is usually the major mechanism for the tool wear in hard rock, the developed methods for cutter wear or cutter life evaluation are mostly based on the abrasion indices such as Cerchar Abrasivity Index (CAI). This paper attempts to review the major methodologies for disc cutter wear and life evaluation and to propose new methods to evaluate cutter life and intervention interval evaluation based on detail information of a mixshield tunnel project in Singapore as well as general information of some other projects from Iran, Italy, South Africa, and France. As the laboratory tests are crucial in the process of evaluation, two new lab tests are developed and used to inspect suitability of the new proposed model for disc cutter wear evaluation."

Jan 1, 2016

A case study of a systematic approach to grinding circuit steady-state optimization is presented. After overall review of the flowsheet, two circuits were prepared for detailed testing. Functional performance analysis was chosen as the primary modelling system, and on this basis a quality assurance program for data gathering was implemented. A number of circuit design and operating variables were experimented with statistical analysis of plant test results revealed relationships previously unquantifiable by any other modelling technique. Improvements in classification system and mill grinding efficiencies were demonstrated and significant energy cost savings thus realized.

Jan 1, 1998

By J. A. Meech

An analysis of screen design options on the operating efficiency of secondary crushing plants has been conducted using a dynamic computer model. The model allows for the simulation of a wide variety of crushing circuits and can be run on either a microcomputer (IBM PC/XT) or a large time-sharing mainframe computer. Size reduction and separation characteristics of crushers and screens are based on standard manufacturer design and performance data. Input/output routines are available in tabular, alarm or strip chart recorder modes to facilitate operation of the program. A number of alternate circuit designs are compared to show the influence of surge capacity, screen size and area, screen deck location, and closed side crusher settings on the operation of a 10,000 ton per day plant. The program is currently in use at Queen's University to teach plant operations and control. It has potential to be a valuable tool for operator training.

Jan 1, 1985

By Kanaan Hanna, Mir Heydari, Dipack Sengupta, Gordon B. French

This article concludes a two-part series on the safety, technology, and economic impact of eliminating safety fuse from metal and nonmetal mines. Discussed are the consequences of fuse abolishment, the technical feasibility of changing to an alternative system, and an economic analysis of initiation systems. Last month, part one (ME, pages 31-35) described current use of initiation systems, incidence of accidents, and consumption values for safety fuse and other initiation systems. Consequences of Fuse Abolishment Cap and Fuse Manufacturers Two major safety fuse manufacturers, Ensign Bickford and Apache Powder Co., share the US fuse market. Marketing of Ensign Bickford safety fuse is done by Dupont. Dupont manufactures electric caps as a main product and recently introduced a new nonelectric initiation system (Detaline). Therefore, Dupont would be only slightly affected by the elimination of safety fuse from metal and nonmetal mining. Ensign Bickford, though a larger manufacturer of fuse, does not appear to emphasize the safety fuse market. In fact, safety fuse sales represent only about 10% of Ensign Bickford's total sales volume. Ensign Bickford is strongly pushing its Nonel product. It appears, therefore, that the elimination of safety fuse would have a limited effect on Ensign Bickford, and could ultimately be to the company's advantage. Apache Powder Co., however, would be seriously affected if safety fuse was eliminated. Safety fuse, although not its only product, constitutes a major source of revenue for the company. It currently does not manufacture a substitute product. Apache Powder Co.'s manager agrees that prohibiting the use of safety fuse would result in a greater market share of initiators for Ensign Bickford. Hercules could also benefit from the prohibition of safety fuse. Metal and Nonmetal Mining Industry According to an explosive company contact, elimination of safety fuse by a mandatory regulation would force some of the small, marginal mines out of business. Another powder company representative believes that eliminating safety fuse will result in uneasy situations for small operators not familiar with other techniques. These operators try to minimize the costs and traditionally like safety fuse. He believes that insufficient proof exists to substantiate the overall safety increase if the fuse is eliminated. Fuse manufacturers and distributors disagree, then, about the impact of safety fuse elimination. However, they tend to agree on some important points: • Safety fuse can be a safe method if applied properly. • Electric blasting can be dangerous due to stray currents, and may have higher misfire rates than safety fuse. • It is very difficult to compare the rate of misfires and partial round failures for different systems. This is due simply to the nonavailability of such data. In many cases, the misfires are not even reported to the shift boss, as required by regulations. • Safety fuse has high acceptance in certain applications, such as a face where Nonel or detonating cord are used, or in open-pit blasting. • The safety fuse industry appears to be phasing out on its own. It is expected that the fate of the safety fuse market will be similar to that of black powder. An investigation by Nitro Noble of Sweden "clearly states that the diminishing use of safety fuse has considerably reduced the accidents in Swedish mines." Mine Data Acquisition and Analysis As a part of the study effort, visits were arranged to 24 metal and nonmetal mines. In most cases, underground visits were accomplished. At least one drilling and loading operation was witnessed. The mines were grouped into four mining areas: Wyoming, Montana, Idaho; western Colorado and eastern Utah; Missouri; and southern Arizona. Of all mines visted, the safety fuse system was used in 11 mines, electrical system in seven, Nonel in five, and the Hercudet system in one surface mine. At each mine, the manager, foreman, and blasting crew were interviewed for information and opinions. Besides informal discussions with mine officials, a questionnaire was also filled out for each mine. Due to the extensive length of the information gathered, these data are not presented here.

Jan 2, 1984

By Paul Soros

A major share of the increase in the energy demands of Ontario province in the next decade will be supplied by bituminous coal mined in the U,S, To be competitive with alternative sources of energy, it is essential that the delivered cost of coal, inclusive of all transportation charges, be kept at a minimum. The Bessemer aid Lake Erie Railroad Company and the Pittsburgh and Conneaut Dock Company are currently building a shiploading terminal at Conneaut, Ohio, to service this tonnage, together with expected increases in coal consumption in the Eastern Lake Erie - Lake Ontario area, (see Fig, 1).

Jan 1, 1965

By G. Bylapudi, A. Spearing, J. Weber, K. Mondal

U.S. National Institute for Occupational Safety and Health (NIOSH) reports state that about 100 million rock anchors are installed annually in U.S. coal mines (Tadolini et al., 2006), and rock-related safety remains an issue. The majority of these coal mines have conditions that make corrosion probable in the longer term. Despite this, very little research has been performed to analyze corrosion and its effects on rock anchors in coal mines. To further evaluate the effects of corrosive conditions in coal mines on rock anchors, three different experiments were conducted during an initial Illinois Clean Coal Institute (ICCI)-funded project from 2008-2009. The results of these experiments were further studied, with additional tests, in the extended ICCI-funded project during 2011-2012. The experiments were destructive testing, electrochemical testing (potentiodynamic polarization tests) and open circuit potential (OCP) testing, conducted in order to study corrosion in environments similar to those found in Illinois coal mines with a focus on major rock anchor types typically installed underground. Destructive test results showed highest reduction in peak strength at higher pH and temperature. From the destructive test results, epoxy-coated and galvanized anchors were observed to be better when compared to uncoated. Electrochemical testing was performed to find the corrosion potential and corrosion rates of ASTM A615 steel grades 40, 60 and 75 in four different solutions of varying sulfur content at ambient temperature. The effect of temperature and pH levels on corrosion potential and corrosion rates of steel grades were also evaluated with additional electrochemical testing, where an increase in temperature with all other constant conditions caused a significant increase in the corrosion penetration rate. OCP data indicated higher corrosion potential values (-mV) for rock anchors in wet areas, when compared to those from the dry areas. OCP test results of the rock anchors from the laboratory corrosion chambers were similar to those measured in the sampled coal mines.

Jan 1, 2013

By S. S. Klima, H. Jiang, T. W. Beck, Y. Zheng

Researchers at the National Institute for Occupational Safety and Health (NIOSH) performed a series of lab tests to evaluate the respirable dust removal capacity of an industrial air-cleaning fan. Limestone and coal dust were tested separately in NIOSH’s full-scale drill table simulator at the Pittsburgh Mining Research Division (PMRD). Gravimetric samplers with Dorr-Oliver Cyclones and 37-mm filters were used at two upstream and four downstream locations inside and outside of the drill shroud chamber. There were six tests performed for both the limestone and coal dust experiments. In the limestone tests, an average respirable dust concentration of 98.86 mg/m3 was achieved upstream of the air-cleaning fan. The filter results show that the averaged respirable limestone dust reductions were 7.84%, 8.81%, 10.94%, and 18.02% at the four sampling locations downstream of the fan. In the coal tests, upstream samplers achieved an average of 129.03 mg/m3 of respirable coal dust. The averaged dust reductions were 9.54%, 9.83%, 18.54%, and 19.21% at the four downstream sampling points. The results indicate limited cost benefits of using this technology because of the relatively low dust reductions determined from this laboratory study.

Feb 1, 2023

By A. Juganda, F. WILSON, G.E. BOGIN, H. PINHEIRO, N. SANDOVAL, J.F. BRUNE

To evaluate methane explosion hazards in underground longwall coal mines, researchers at the Colorado School of Mines developed a computational fluid dynamics (CFD) model along with a 1/40th-scale, optically accessible, physical model of a longwall mining section. In this project, CFD models assisted in the design of the physical model to ensure specifications were met to accurately represent the scaling physics as well as to assist in narrowing the experimental matrix and identifying key locations for sensor placement to measure velocity, pressure and gas concentrations. This research will help develop strategies for methane monitoring to prevent methane ignitions and explosions in longwall coal operations.

Dec 1, 2022

By Jessica M. Wempen, Dallan J. Coons, Bailey S. Simmons, Michael K. McCarter

Gate-road yield pillars are subject to increases in stress as the longwall face advances toward the pillars. Increases in pillar stress can be inferred by measuring roof/floor convergence surrounding the pillar. This paper presents a case study of convergence measurements surrounding a two-entry gate-road yield pillar in the head gate of a coal mine. Convergence was measured over a six-month period, as the longwall face approached and passed the pillar. Measurements were collected at eight locations surrounding the pillar: four locations in the travelway and four locations in the beltway. In addition to convergence stations, the pillar was instrumented with an array of seismometers. In future analysis, convergence measurements will be compared to seismic interpretations. This study reports on the geology and geometry of the longwall panel, the roof and rib support, the change in convergence over time, and the physical properties of coal and parting. Additionally, the convergence measurements are compared to pillar safety factor distributions derived from a finite element model. The convergence measurements contribute to the knowledge of when yield pillar abutment loading, caused by the encroaching longwall, is first detected. Knowing when abutment loading begins to yield the pillars can help define when standing secondary roof supports are required for head gate entry support.

By R. R. Klimpel

The efficiencies of plant scale comminution processes are often evaluated by various indices that are calculated and/or measured somewhat independent of the performance of any associated downstream froth flotation processes. In order to compare some specific comminution factors such as energy utilization, media consumption, equipment utilization time, etc. comparisons of comminution efficiency independent of flotation behavior are appropriate. However, as more and more detailed plant level information is gathered on the joint and highly interactive nature of comminution and froth flotation, it is becoming increasingly obvious that knowing and using simple efficiency indices are not enough. What is needed are more performance related measures of the efficiencies of the combined size reduction -froth flotation system for effective plant level economic optimization to occur. The purpose of this paper is to present some examples of important interactions that influence the joint efficiencies of size reduction and froth flotation processes.

Jan 1, 1998

By K. Nielsen

The Norwegian tunnelling industry has made remarkable improvements both with regard to productivity and cost efficiency over the last 30-40 years. This development has been made possible by continuous improvement driven by innovation. Based on a generic description of the innovation process and the innovation system, the paper has used the development of modern tunnel drilling in the Norwegian tunnelling industry to discuss the characteristics of its innovation system with a focus on human capital issues and knowledge management.

Jan 1, 2006

By K. A. Smith, X. Cheng

Introduction The separation of minerals from complex sulfide ores by flotation requires careful control of the surface chemical behaviors of the minerals constituting the ores. When the minerals in the ore are finely disseminated, extremely fine grinding is needed to liberate the minerals. Fine grinding is not only an energy-intensive operation, but also influences the flotation behaviors of liberated minerals. Steel balls are commonly used for grinding. Galvanic interactions occur not only between sulfide minerals and grinding media but also among the different sulfide minerals themselves. The electrochemical characteristics of chalcopyrite and pyrrhotite when they are independently coupled with steel grinding media and the relevance of these characteristics to the flotation behavior of these minerals have been exten¬sively studied (Cheng and Iwasaki, 1992: Li and Iwasaki, 1992). These studies dealt with reactions in two electrode combinations, simulating mineral-grinding medium and mineral-mineral interactions. In practice, however, it is more common to involve more than one sulfide mineral. In a study of a pyrite-pyrrhotite-mild steel system, Pozzo et al. (1989) provided evidence that a mineral having an intermediate potential could behave differently, depending on the condi¬tion of galvanic contact. This investigation was undertaken to study a chalcopyrite-pyrrhotite-mild steel system to gain better in¬sight into the mechanism of multiple galvanic interactions. A three-electrode system was chosen to simulate a typical copper sulfide ore. The sulfide minerals were represented by chalcopyrite and pyrrhotite. The grinding medium was rep¬resented by mild steel. The nature of galvanic interactions involving these minerals and grinding medium in an oxygen atmosphere was investigated in a three-electrode combina¬tion, and an attempt was made to relate the laboratory flotation results of pyrrhotite-chalcopyrite ores. Possible implications to the differential flotation of complex sulfide ores are discussed. Key words: Electrochemistry, Flotation, Sulfide ores Experimental The pyrrhotite (57.74% Fe, 0.09% Cu, 4.84% Ni and 36.54% S) sample was obtained from Falconbridge Ltd.'s Strathcona mine, Ontario, Canada, and the chalcopyrite (26.00% Cu, 28.57% Fe, 0.05% Ni and 31.52% S) sample came from Transvaal, South Africa. Mild steel (AISI 1020, 0.2% C) was chosen to represent grinding media. A conventional three-electrode cell was used in the elec¬trochemical measurements. The working, counter and refer¬ence electrodes were, respectively, sulfide minerals or mild steel, graphite rod and saturated calomel electrode (SCE, 0.245 V vs. standard hydrogen electrode). The exposed areas of the sulfide minerals and grinding medium electrodes were approximately the same (0.17 to 0.19 cm2). The preparation methods of working electrodes, the reagents used, the experi¬mental procedures and the instrumentation were the same as those described previously (Cheng and Iwasaki, 1992). Rest potentials of pyrrhotite, chalcopyrite and mild steel were measured individually in 0.05-M sodium sulfate solu¬tions. Combination potentials and galvanic currents of the sulfide minerals and grinding medium were measured in short-circuited two- and three-electrode systems. All poten¬tials in this study are quoted in volts with respect to the standard hydrogen electrode (SHE). To simulate the constantly abrading conditions in a ball mill, rest potentials, combination potentials and galvanic currents were also measured by rotating a porcelain ball against chalcopyrite, pyrrhotite and mild steel electrodes in

Jan 1, 2000

By Herschel H. Potter

Back injuries arising from such activities as lifting and handling objects have been and continue to be constant and undiminishing hazards of the occupational environment. Back pain in one form or another is experienced by almost a1 1 individuals. During the past 30 years, a great deal of accident prevention education has been directed toward the reduction of back injuries. However, it has not produced any great change in the incidence of the injury. The human spine remains the most vulnerable area of the muscul o-skeleta1 system. Back injuries account for about 400,000, or 18 percent, of all disabling work related injuries each year according to the National Safety Council estimates. These serious back injuries are estimated to have cost more than 1.9 billion dollars in 1976 in medical and lost time pay. 1

Jan 1, 1981

By William J. Cavanaugh

In 1967, Lone Star Industries, Incorporated, established a program to carry out the necessary Research and Development work to bring the Snyder Process to commercial application. The purpose of this paper, is to present the detailed metallurgical results gathered in comparing the Snyder Process of Comminution to conventional grinding techniques for the milling and beneficiation of certain ores and other materials. The ore primarily dealt with in this paper is a fine-grained magnetite ore, containing approximately 23% acid-soluble iron, from the Lake St. Joseph ore body of Steep Rock Iron Mines, Ltd., (Canada). This particular example was selected for presentation in this paper because extensive comparative results with conventional methods of grinding were available. Also briefly described in the paper are the comminution of other ores and materials such as porphyry copper ore and alumina.

Jan 1, 1973

By G. B. McClurg

China was nota factor in the supply of fluorspar to the United States until the early 1980's when it shipped in its first package of Metallurgical lump, that not only was higher grade than the Mexican Metallurgical spar but was also about $30.00 a ton cheaper landed at Burnside. Representatives of the Mexican Fluorspar Institute and several producers made trips to see the Chinese operations supplying their once reserved market place. China, an enigma to most Westerners suddenly became the new contender, with prices that were disgustingly low or so thought the other exporters. Of course China has been mining, producing, consuming and exporting from 400,000 to 500,000 tons per year of various grades of fluorspar but until the first partloads came to the U.S., very little attention was paid to their exports by American-continent producers or consumers.

Jan 1, 1986

By Yi Luo

Subsidence events occurred over inactive room and pillar (R&P) mines, including abandoned mines or sealed portions of active mines, are classified as unplanned subsidence because of their timing and distribution are unpredictable. When investigating such subsidence cases, many uncertainties exist and disputes often focused on whether the observed structural damages are caused by mine subsidence or other natural or artificial causes. However, solid evidences to identify the causes are often lacking. In order to conduct a thorough and impartial investigation, good knowledge in subsidence theories a

Jan 1, 2009