Search Documents

By W. M. Aubrey

The use of solid fuel in shaft furnaces to indurate iron ore pellets was originally considered a necessary evil, which the industry worked long and hard to eliminate. Since then changes have taken place in furnace design and operating practices that have led us to our suggestion that solid fuel additions could again be used. In essence, what has happened is that the developments which made it possible to operate without solid fuel have also created new operating conditions favorable to the effective use of solid fuel. Because these new conditions* were brought about in part by the desire to eliminate solid fuel and because the development was a gradual one, the industry failed to reassess its position and for years neglected the possibility of returning to solid fuel.

Jan 1, 1967

By Todd S. Webster, Matthew J. Pierce, Brad D. Krumel

With the Working Shafts and Starter Tunnel under way, it became apparent this 4.7-mile, 19-foot diameter wet weather tunnel was going to live up to its name. The shaft’s pre-excavation grouting was completed, and ground water inflows were slowing project progress. As the tunnel drive was approaching 50% complete a cooperative effort was underway between the owner, engineer, and contractor to raise the base of the Retrieval Shaft by 65 feet to avoid ground water infiltration construction challenges. The tunnel alignment needed to be raised in kind. The project was behind schedule and rethinking the cast-in-place adit work was next on the agenda due to the very wet environment in the tunnel. The race was on to finish the project within the owner’s time constraints while completing multiple redesign aspects of the tunnel alignment and associated adit construction. This paper will evaluate original design criteria and actual in-route design modifications and change management to meet the owner’s just-in-time schedule needs.

Dec 1, 2022

By L. Alan Weakly

The Powder River Basin is the largest strippable reserve of compliant coal in the United States. It is the mother lode, for this Basin is currently supplying 25 percent of the coal produced in the US annually. This paper updates what has happened in the Basin since 1993 in terms of increased production, higher productivity, changes in mine ownership, safety statistics, new equipment, latest coal technologies, and electrical deregulation ramifications.

Jan 1, 1998

By ERIK CHARRIER, ADITYA JUGANDA, Jürgen Brune, Patrick Maier, Gregory E. Bogin Jr

Confined explosions are a major risk in underground coal mine operations. Depending on confinement, ignition location and obstacles in the flame path, methane explosions can transition to detonations. As a result, the severity of mine explosions ranges from minor damage to loss of lives and permanent mine closure. Experimental results have shown that the inclusion of obstacles can significantly increase the flame propagation velocity by inducing turbulence. This research focuses on explosion experiments in a 71 cm diameter, 30.5 m long reactor that includes rock piles as obstacles along with developing the corresponding CFD model that captures the observed flame behavior and interaction with the obstacles. The rock rubble increases the flame front propagation velocity by 500% compared to the maximum velocity observed in the empty reactor experiments. The 2D and 3D CFD models predict the experimental flame front propagation velocity, whereas the 3D model shows a more explicit conformity than the 2D model. Although the computational time to complete the simulation is much less for the 2D model than for the 3D model, the 2D model is not sufficient to simulate cases with rock rubble since it cannot capture the propagation of the flame through the small voids between the rocks with the same effective blockage ratio as the 3D model. The validated CFD model can be scaled up to simulate methane explosions in full scale mine and industrial settings.

Nov 20, 2023

By S. G. Dixit

Alunite (KAl3(SO4)2(OH)6] is one of the important nonbauxitic resources for aluminum in U.S.A. The major gangue material associated with a unite ore body is quartz. Experimental results indicate that oleic acid flotation of alunite is quite effective in upgrading the ore. The flotation chemistry of the alunite/oleate system has been investigated using various techniques such as: hallimond tube flotation response, measurement of adsorption density using I4C labeled oleated, electrokinetic measurements, infrared spectral studies, contact angle measurements and thermochemical measurements using an isothermal microcalorimeter. Alunite has been found to float readily with oleate in the pH range 4-10.5 and its flotation response is enhanced at higher temperatures. The PZC of alunite has been determined to be at pH 7.2 ± 0.15 which agrees with what would be predicted from solution chemistry and from the flotation response with physically adsorbed collectors. Infrared spectra show a specific peak in the range 1585-1600 cm-1 which has been attributed to the formation of an aluminum oleate surface species. Both adsorption density measurements and infrared spectra indicate that during adsorption multilayers are formed. The heat of adsorption of oleate on alunite has been found to be endothermic and of the order of 4-6 KJ/ mole.

Jan 1, 1980

By J. P. Ulery

As a result of several recent methane/dust ignitions in surface auger and highwall mines, the U.S. Bureau of Mines investigated the occurrence of methane gas at these operations. Three mine sites were visited in western Kentucky and one in western Pennsylvania to collect run-of-mine coal samples for gas content determination using the modified-direct-method (MOM). Results indicate the samples emitted small quantities of methane, carbon dioxide, and nitrogen. Either methane or nitrogen was the predominant gas released. The same gases were released after crushing the samples for residual gas content; however, nitrogen was the primary component of this fraction. Total ~as contents ranged from less than 0.01 cm /g to 0.54 cm3/g. The hydrocarbon gases probably originated during coalification. Other gases may have originated partially as a byproduct of coalification and partially as a result of other, near-surface processes. The data suggest that although methane quantities are small, desorption could occur at near surface conditions prior to mining. The desorbed methane could accumulate as a free gas in fractures in the coal bed or roof rock. When these fractures are penetrated by the auger, methane could rapidly enter the whole atmosphere possibly creating explosive conditions.

Jan 1, 1994

By J. Frostiak

The Campbell gold operation of Placer Dome Inc. produces an arsenopyrite-sulphide concentrate which must be treated either by roasting, biooxidation or by pressure oxidation to obtain high gold recoveries. Pressure oxidation is a proven process and has the inherent advantage of meeting the stringent environmental regulations in the province of Ontario. A comparison of biooxidation and pressure oxidation was completed early in 1990 and the latter was selected by Placer Dome as the preferred process for replacement of the roasters. The commercial plant design was based on technology supplied by Sherritt Gordon and in July of 1991, the existing roaster operation was shut down and a new pressure oxidation plant was commissioned. The following summary describes the start up of the new facility and presents typical operating data.

Jan 1, 1992

By D. C. Seidel

The role of surface charge in soluble salt flotation, which was developed in Part 1, is extended to relate the theory to the specific phenomena of KCI- NaCl separations. Temperature-collector solubility relationships, metal ion activation, and particle size effects are discussed.

Jan 1, 1967

By J. L. Coburn

The Huari-Huari ore body is located in Southern Bolivia, at an elevation of approximately 3,800 meters above sea level. The ore is a complex massive sulfide, slightly marmatitic sphalerite, in a fault fissure filled hypo- thermal vein in Paleozoic shales and quartzite-altered sandstone. The sphalerite has common associations with pyrite and quartz and is frequently intricately intergrown with stannite, chalcopyrite, and pyrrhotite. The sphalerite also contains numerous inclusions of pyrite, marcasite, galena, boulangerite, jamesonite, quartz, arsenopyrite, and cassiterite. A research program was undertaken to develop a flowsheet for the recovery of separate silver, zinc, and tin concentrates by selective flotation. Based on this experimental work and subsequent flowsheet development, engineering and construction of a 500 metric ton per day concentrator was undertaken. This paper describes the process that was developed for the Huari-Huari ore and the unique aspects of the Huari-Huari concentrator.

Jan 1, 1977

By G. Bulut, Ü. Yenial

"The use of recycled water in flotation has significant effects on flotation and selectivity because the recycled water contains many dissolved compounds and ions that alter the chemistry of the system. In this study, the effects of calcium, magnesium and sulfate, which are abundant components in recycled water, were investigated on galena, sphalerite and pyrite flotation using pure minerals and a complex sulfide ore by conducting bench-scale flotation, microflotation and zeta potential measurements. The bench-scale flotation tests indicated that higher recoveries of galena and sphalerite are obtained when water is recycled, due to higher concentrations of ions in recycled water. However, there was a critical ion concentration for galena recovery. The microflotation tests showed that galena recoveries at different pHs in recycled water are lower than in tap and distilled water. Pure sphalerite recoveries improved in recycled water in the bench-scale test with ore. Pure pyrite was depressed with recycled water as well. Zeta potentials became less negative with increased calcium and magnesium ion concentrations due to their adsorptions, and the presence of sulfate ions was seen to increase the negative charges of sphalerite and pyrite, conversely for galena. IntroductionWater is among the most important elements for mining and mineral processing. The distance to water sources is one of the major factors for mine site selection. The mining and mineral processing sector needs and consumes large quantities of water. In Chile in 2014, the copper mining sector alone consumed 12.7 m3/s fresh water for 1.189 tons of ore processing, and recycled 74 percent of the consumed water (Chilean Copper Commission, 2015). A plant that does not reuse or recycle any water will require 1.9 to 3.0 m3 of water per ton of ore processed (Gunson et al., 2012). Many stages of mineral processing, such as grinding, gravity concentration, dense medium separation, wet magnetic separation, flotation and hydrometallurgical operations, use large volumes of water (Schumann, Levay and Ametov, 2009).In mineral processing plants, the process water is recycled from the tailings dams, thickener overflows, and dewatering and filtration units. Wet concentration processes can require large quantities of water. Flotation, the most common process, typically takes place at 25 to 35 percent solids by mass. Most flotation plants practice at least some water reuse and recycled. Modern mines and mineral processing operations generally aim for zero water release (Levay, Smart and Skinner, 2001). In most cases, water quality has been found to affect flotation performance, and this interaction remains under investigation."

Jan 1, 2016

By M. Westerstrand

The processes involved in the concentration of magnetite ore with process water as the aqueous medium can have a strong influence on the surface properties of the magnetite particles. In this study, different leaching methods, as well as zeta potential measurements, were used to examine the major easily accessible ions on the particle surfaces and their effect on the surface charge. The results show that the enrichment of elements on the surface of the particles appears early in the refinement process. Ca was enriched up to 15 times and Si up to 50 times compared to what pore water alone would have given. The leaching experiments also showed that the addition of water glass increased the surface enrichment of Si and that the collector might hinder desorption of Ca. An alkali leaching method was evaluated, which showed that Si was much more enriched than S and Cl. Zeta potential measurements on synthetic magnetite particles showed that process water resulted in zeta potentials different from the potentials measured for these particles in aqueous calcium and silicate solutions. Therefore, it is important to consider the complexity of the process water when making predictions about the properties of the particle surfaces in the final magnetite concentrate, which most studies do not. Zeta potential measurements were also used to rule out a strong influence from organic matter in the process water on the magnetite zeta potential.

The height of permanent slopes at the Panguna mine of Bougainville Copper Limited will vary from 350 to 950 metres. A few degrees difference in slope angle has a large effect on the ore/waste stripping ratio. Optimum slopes can be achieved if longer batter slopes (exceeding 45m height) are excavated using bulldozers to trim parallel to controlling fracture surfaces. Unnecessary slope flattening by incorporating benches can cost millions of dollars in lost ore. Faults and other major weaknesses, which can result in wedge failure or erodible zones have been treated successfully with shotcrete, rockbolts and cable dowels. To minimize support effort and interference with mine production, early identification and treatment of unstable areas is important.

Jan 1, 1987

In this paper, the logic and the capabilities of a long term production planning method for open pit mining are presented. The method is the first attempt in obtaining simultaneous solutions to the four interrelated parameters of open pit mining; 1) the mine life, 2) the specific blocks to be mined each year, 3) the amount of ore and waste to be mined each year, and 4) the ultimate pit limits. An efficient cutoff grade can also be obtained through a sensitivity analysis. None of the existing methods can bring such a comprehensive solution to the problem. A production plan for a real life gold deposit is given to illustrate the logic and the capabilities of the method.

Jan 1, 1993

By F. M. Benavides

The mining complex being analyzed consists of four mines and two processing plants located in an area where there are several existing modes of transportation. Figure 1 shows a map of the general layout of the four proposed mines and the two existing processing plants. The mines are identified by the numerals "I" through "IV" and the plants by the letters "A" and "B". A proposed overland conveyor would collect the product from all four mines and convey it to Processing Plant A. Alternate transportation systems are as follows: Railroad transport from Mines I and II to Plant B; Highway trucking from Mines I and II to Plant A; Off-the-road truck haulage from Mine III to Plant B and from Mine IV to Plant A. River transportation from the mines to the processing plants was not considered in this study under the assumption that the high capital investments for the loading and unloading facilities, in addition to difficult traffic problems, would make this mode of transportation unattractive.

Jan 1, 1980

By Onuralp Yücel, Kağan Benzeşik, Ömür Can Odabaş, Selçuk Kan

Extraction and processing constitute an important area in the metallurgy of molybdenum. Molybdenum trioxide (MoO3) production is one of the most important stages in molybdenum production. In this study, the effects of different furnace types on MoO3 production were investigated by using molybdenum concentrate as a raw material obtained during the enrichment of copper ores. Preliminary experiments have been made using a chamber type furnace, and a transition to a pilot-scale has been carried out with rotary kiln experiments. The effects of a different time and atmospheric conditions on MoO3 roasting kinetics were investigated by experimental studies conducted in the temperature range of 500–650°C. It was determined that the optimum temperature and time for sulfur (S) removal was 625°C and 180 min in the studies carried out in the rotary kiln, and it was determined that 0.61%S content was reached with an average removal efficiency of 98%. The activation energy in these sets was calculated as 89.519 kJ/mol.

May 3, 2021

By Brian Young, Ben Pantony

Interferometric Synthetic Aperture Radar (InSAR) has played an integral role in many large scale tunneling projects globally. Until recently, it has been regarded as a complementary monitoring tool. On the Los Angeles Metro Purple Line Phase 1, InSAR was proposed as a primary means to replace weekly and bi-weekly surface monitoring requirements on surrounding critical infrastructure. This paper will summarize the statistical analysis approach engaged in order to compare and contrast a year of historical InSAR data to known geodetic survey data, in order to utilize InSAR as an operational monitoring tool on this project.

Jun 13, 2021

By D. J. MacKinnon

Smooth, compact, dendrite-free, 24-h zinc deposits have been electrowon from zinc chloride electrolyte using a diaphragm cell. The cell consisted of sealed anode compartment con- taining DSA anodes which were separated from an open cathode compartment by Dynel cloth membranes. Fresh electrolyte was fed to the cathode compartment where zinc deposition onto an aluminum cathode was aided by air-sparging. The catholyte passed through the diaphragm into the anode compartment from which chlorine gas and spent anolyte were withdram.

Jan 1, 1980

By M. Deutsch, E. González, M. Williams

"Uncertainty exists in ultimate-pit limits due to geologic variation and unpredictable economic landscapes. In this work, we show how this uncertainty affects the ultimate pit and how it can be analyzed to improve the mine planning process. A stochastic framework using geostatistical simulation and parametric analysis was used to model the effects of geologic and economic variations on ultimate-pit limits and overall project economics. This analysis was made possible by a new pit optimization implementation that can be automated and set up to calculate ultimate pits for hundreds of different scenarios in a matter of hours. Quantifying ultimate-pit uncertainty early in the mine planning process allows mining engineers to make informed decisions regarding infrastructure placement and to mitigate the possibility of incurring substantial costs to relocate critical mine facilities. Resumen ¦ Existen dudas sobre los límites del pit final por causa de la variación geológica y lo impredecible de los paisajes económicos. En este trabajo les mostramos como esta incertidumbre afecta el pit final y como puede ser analizada para mejorar el proceso de planificación de la mina. Se usó un marco estocástico con simulación geoestadística de análisis paramétrico con el fin de poder hace la modelación de los efectos de las variaciones geológicas y económicas en los límites de pit finales y proyectos económicos en general. Este análisis fue posible gracias a una nueva implementación de optimización de pits que puede ser automatizada y configurada para calcular pits finales para cientos de escenarios diferentes en cuestión de horas. La cuantificación temprana de la falta de certeza en pits finales durante el proceso de planificación permite a los ingenieros de minas tomar decisiones informadas en lo que respecta a la ubicación de infraestructura y en la mitigación de posibles costos sustanciales por causa de la reubicación de instalaciones clave de la mina."

Jan 1, 2015

By J. Brune, P. J. Coleman, L. Martini

Research in the field of mining safety and health in the United States plays an important part in protecting the lives of miners. The National Institute for Occupational Safety and Health (NIOSH) Mining Program conducts surveillance, studies and developmental work aimed at improving the safety and health of miners. With recent reviews of the Mining Program by the National Academy of Sciences and the Mining Program response (NIOSH, 2008), the importance of setting goals, conducting high quality engineering and scientific research and evaluating the outputs, outcomes, relevance and impacts of these projects has been reemphasized. Surveillance of reported injuries is a first step in deciding on research directions and in designing specific projects. Groups of injuries often share features and attributes that suggest common causes and may respond to similar preventive efforts. Identifying groups of injuries also serves to prioritize intervention efforts. The Mine Safety and Health Administration (MSHA) Accident and Injury database (MSHA, 2008) provides individual case reports of mining injuries, illnesses and certain no-injury accidents (events such as roof falls that stop mine production or miners’ activities for more than one hour). This database is an indispensable resource for researchers and stakeholders needing information on the statistics of these events. From an epidemiological perspective, research projects target groups of miners at risk due to specific patterns of work, equipment, mine settings and the management of safety and health in their mines. Incidence rates are provided by the MSHA data for selected variables, such as surface/underground location, standard industrial classification and state. While incidence rates are the preferred measure for all variables, denominators are not typically available; for example, to more clearly understand the data about injury by occupational type, it would be necessary to conduct demographic surveys. A current survey of the demographics of the mining industry should be complete by 2010, which will allow incidence rates to be developed for a number of variables such as age, occupation and experience. This survey will provide the first update of its kind since the first survey was conducted in 1985. This report describes an alternative method of analyzing and presenting MSHA data for the purpose of identifying high-cost, high-severity injuries and illnesses. Researchers at the NIOSH Spokane Research Laboratory (SRL) developed programs to find the top five most frequent accident classes, natures of injury, types of accidents and other selected variables from the MSHA database. Studying these variables gives a cross-sectional snapshot of the most frequent groups of injuries within a commodity, regional group or time period, and allows researchers to quickly understand developing patterns for new research projects. The primary benefit of this approach is to

Jan 1, 2009

By Zhiyuan Ma, ZUI WANG, Xincheng Hu, Jianwei Cheng, Junhong Si, Yi Qin, Gao Ke

The harmfulness and destructiveness of mine gas explosion is quite serious, which is the first of all kinds of coal mine disasters. Once the gas explosion occurs, it could instantly generate explosion shock waves, high temperature airflows, and disaster gases, which cause the destruction of underground ventilation structures, disruption of airflow direction in a mine ventilation network, and miners’ deaths by asphyxiation. As an important barrier to prevent the spread of accidents caused by the gas explosion, the safety and reliability of the mine seal affects the mine’s production and the health of workers. Due to the demands of coal mine production and transportation, a large number of longitudinal and horizontal roadway networks have been developed underground. There are not only many flat and straight roadways in the complex roadway network structure, but also a large number of different types of bifurcations and bends. Once a gas explosion occurs, the impact of the blast waves on the mine seal after passing through the complex path is difficult to determine. Therefore, this paper establishes a numerical model of bifurcated and cornered roadways and studies how the impact of gas explosion shock waves on the structure of sandwich mine seal after passing through different types of bifurcated and cornered roadways. The damage state of sandwich mine seal is analyzed. The researching finding could prevent and manage the spread of gas explosion disaster, and improve the disaster mitigation of mine explosion accident.

Jul 11, 2023