Search Documents

By R. O. Burt

The paper examines the role of gravity concentration in both an historical contest and within the modern mineral processing industry. It discusses the principles of the process on both a theoretical and practical level. The importance of ore mineralogy and its effect on the choice of the wide range of equipment available is discussed. The paper concludes with a discussion on the relative merits of gravity concentration to other forms of processing and seeks to answer the classical question - "Quo Vadis?"

Jan 1, 1982

By James L. Hendrix

This paper is intended to give the reader an update on the work being done at the Mackay School of Mines about the fate of cyanide on precious metals mill tailings waste. During the last two years several tailings impoundments have been sampled and analyzed for total and free cyanides. From our sampling program we are beginning to learn valuable information concerning the fate of cyanides in precious metals mill wastes. Included in this paper is a detailed description of our sampling and analytical techniques. Also, some of the data obtained from five sites are given.

Jan 1, 1986

By R. Mensah-Biney

The aqueous biphase separation process (ABS) has been used to separate ultrafine industrial minerals. The partition behavior of TiO2, Al2O3, Fe2O3 and kaolin was not pH dependent. The partition behavior of SiO2 was, however, pH dependent. The partition coefficient of kaolin in PEG 3400/ Na2CO3 biphase system was = 150 and that of the silica in the same system was = 0.02, resulting in a separation factor of = 8500 between kaolin and silica. The aqueous biphase separation system was used to separate free silica from kaolin in a raw clay sample from Mexico. The partition behavior of mica, feldspar and clay from North Carolina was also evaluated.

Jan 1, 1999

By R. Casagrande, L. R. Moore, J. Sessoms, P. Macy

"A South American nickel mine has been producing a nickel concentrate that also contains copper and iron (15 percent nickel, 5 percent copper, 28 percent iron) for the end use of stainless steel production. A critical specification for the quality of the steel is the iron to magnesium oxide ratio (Fe:MgO), with a ratio of below 3.5:1 having a substantial impact on the nickel value. This nickel concentrate producer historically mined the sulfur-rich mineral pyroxenite but had been forced to move to a magnesium oxide/silicate (MgO/SiO4)-rich mineral harzburgite, resulting in nickel recovery being reduced to around 50 percent to maintain the required Fe:MgO ratio. In this study, ore mineralogy, water chemistry and the chemistries associated with the flotation process were evaluated in an effort to increase nickel recovery while maintaining the Fe:MgO ratio according to specification. New chemistry was introduced with the specific goal of complexing with the MgO and retarding its interaction with the bubble flow in the flotation process.IntroductionGlobal nickel production in 2011 totalled to 1,770,000 tons, according to the Raw Materials Group (2013). From 1950 to 2005 there was an aggregate 4.4 percent increase in nickel production, with a market-value high of $1,000/ton nickel reached in 1998 (Mudd, 2010). Approximately 65 percent of nickel production is consumed by the stainless steel industry, with 12 percent of the remainder used in super alloys or nonferrous alloys. Nickel imparts corrosion resistance, temperature resistance and other benefits to its alloys (Table 1) (Oberg, 1996; Cáceres, 2003). The dominant types of nickel-bearing ores are classified as either laterites (limonite: nickel-iron oxide; and garnierite: nickel hydrosilicate) or magmatic sulfide deposits (pentlandite: iron-nickel sulfide) (U.S. Geological Survey, 2013a, 2013b). In 2012, about 40 percent of the nickel ore mined was sulfidic-type ores and about 60 percent was laterite. The processing of laterite ore is expected to continue to increase as the availability of sulfidic ores continues to decline."

Jan 1, 2015

By Wang Xuewen, Bao Qingbao, Xie Jiacheng, Yan Zewen

This study puts forward a virtual memory cutting method based on the prediction of AFC shape. The integrated key technologies include the generation of virtual teaching cutting curve, the height adjustment strategy of front and rear drum, cutting height adjustment strategy, the reciprocating cycle of cutting technology and so on. Through the two algorithms, SVM and ELM, the form of the next working cycle can be obtained by rolling prediction using the form information of AFC in the first several circulations. Based on the obtained dynamic fluctuation of the form in the vertical and horizontal working faces, the position and cutting information of the shearer during its operation can be controlled and predicted in advance, the memory cutting template can be adjusted and modified in time. Employing this method, the more stable, accurate and timely memory cutting of the shearer under the uneven coal seam could be realized.

Aug 16, 2021

By D. E. Severson

The coal solution refining process under investigation is basically a modi¬fication of the German Pott-Broche Process, on which patents date back to 1927, (5, 6). This process was used in Germany during World War II for the partial dissolution of coal in hydrocarbon solvent and removal of the ash by filtration to produce a raw material for carbon electrodes for aluminum plants. At the end of World War II the German synthetic fuel program, of which this process was a small part, was abandoned as not economical. In recent times the whole field of coal liquifaction has been given a new impetus; present technology indi¬cates that the economic processing and refining of coal may be possible in the United States. A number of approaches to coal liquifaction have been investigated, and several of these are currently being funded by the U. S. Office of Coal Research. One approach is direct thermal treatment of the coal as in the FMC Project COED, in which coal is thermally cracked to produce gas, liquid products and char. Another approach is the Hydrocarbon Research Institute's H-coal process in which coal is catalytically hydrogenated. Two other federally funded projects involve the extraction of coal by solvents. The Consolidation Coal Company's Project Gasoline, now in the pilot plant stage in Cresap, West Virginia, is an attempt to produce gasoline plus a residual char by partial solution of the coal substance. The coal de-ashing process being developed by the Pittsburgh and Midway Coal Company is a modification of the Pott-Broche process. Coal derived solvent is used with hydrogen to dissolve the entire coal substance, subsequent filtration removes the ash and the solvent is recovered for recycling.

Jan 1, 1968

By E. H. Smith

St. Joe Minerals Corp., a subsidiary of Fluor Corp., treats high-grade gold, silver, and copper ore at its El Indio plant at an altitude of 4 km in the Chilean Andes. The ore is complex, being a mixture of massive pyrite-enargite and quartz, both containing very fine gold and silver. Treatment produces a copper flotation concentrate containing high levels of gold, silver, and arsenic, and also dore bullion. Part of the flotation concentrate is roasted to remove the arsenic content, and arsenic trioxide is collected as a by-product.

Jan 1, 1987

By Eugie Kabwe

The effective employment of a pretensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut preload. In this paper, a load indicator washer (LIW) able to withstand an assigned static loading as well as provide an appropriate pretension is presented. The different LIW breadths are numerically analyzed with ABAQUS finite-element code to estimate deformation when a designated 60 kN preload is applied. The numerical simulation employs the bilinear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nut-LIW-rock bolt connection. Therefore, long-term relaxation effect on bolt pretension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW predetermined deformation is the bolt pretension. It is drawn from the simulation results that LIWs with thicknesses of 1.5, 2.0, 3.0, 3.5 and 4.0 mm are completely flattened when subjected to 28, 42.5, 65, 76 and 88 kN preloads, respectively.

By Moussa Wone, Jeff Peterson, Filippo Azzarà, Daniele Nebbia

The DC Water and Sewer Authority's Long Term Control Plan includes tunnels, sewer separation, pumping station rehabilitation and green infrastructure to reduce combined sewer overflow (CSO) discharges to the District waterways. The Northeast Boundary Tunnel is a deep, large sewer tunnel that will reduce CSO discharges; signifi- cantly mitigate known chronic flooding in the Northeast Boundary drainage area and improve the water quality of the Anacostia River. This paper presents the unique combination of Owner and Contractor perspectives of the entire Project from conception through procurement, execution, and contract management, providing lesson learned, chal- lenges encountered, and solutions implemented to deliver the Project successfully.

Jun 23, 2024

By Amanda Powers, Brian Glynn, Robert Sauceda, Daniel Huffines, Mike Garbeth

This paper will review the evaluation performed for the Cottonwood & Hackberry Creek Wastewater Interceptor Improvements Project to replace two separate aging and undersized interceptor sewers by either open cut construction or trenchless construction methods. A case study will be discussed for the utilization of microtunneling to avoid a deep open cut excavation within a landscaped roadway median to construct nearly a mile of new 60-inch interceptor sewer in an urban area adjacent to an environmentally sensitive riverine area, while minimizing the permitting and environmental impacts of construction, and minimizing the impacts to residents and vehicular trafc and restoration reuirements.

Jun 23, 2024

By D. J. Englund, R. A. Davis

"A three-dimensional CFD model of a straight grate furnace for indurating iron-oxide pellets was developed for exploring conditions of furnace operation for fluid flow, heat transfer and reactions. The model includes reactions for natural gas combustion in the gas phase and calcination and magnetite oxidation as well as drying in the pellet bed. The performance of the model was investigated with a series of pellet production rates that included adjustments to the fuel rates to achieve proper induration temperatures in the pellet bed. The model may be used to discover opportunities for process improvement.IntroductionIron oxide pellets are a feedstock to blast furnaces for iron making. Pellets require physical strength characteristics needed to maintain their integrity during storage, handling, transportation and smelting. Pellets are produced from iron ore in a series of mineral processing operations that form wet green balls from slurries of iron-ore concentrate with binders, such as bentonite, and possibly fluxing-agents such as limestone and dolomite. The green balls are dried, fired at high temperature, and then cooled in an induration furnace to achieve the strength and chemical composition required for efficient reduction and slag separation in blast furnaces. Induration furnaces are generally straight grates or grate-kilncooler configurations. These furnaces operate with pellet beds passing through a series of temperature zones to control drying and chemical reactions in the bed.Process air passes through the zones in an overall counter flow direction to the pellets for efficient heat transfer and energy recovery from the cooling stage. Consequently, the zone conditions and the overall furnace performance are highly coupled. Thus, it becomes challenging to predict how changes to any single zone may affect the rest of the furnace. To gain a better understanding of machine performance and coupling, a three-dimensional, steady-state model of a complete straight grate induration furnace was created using computational fluid dynamics (CFD)."

Jan 1, 2015

By R. F. Yap

Although laboratory studies of tin flotation have been reported as far back as the 1920`s(1), the commercial application has only been realized within the past few years(2,3). The principal technical difficulty in the application of the process to tin ores has not been in the flotation of cassiterite itself, this mineral being readily recoverable with the common collectors, including xanthates with heavy metal ion activation(2). The difficulty has been with the depression of the gangue minerals commonly associated with tin ores, and to a lesser extent with the problems of collector consuming semi-colloidal minerals which are in some cases present. The application of sulfosuccinamate collectors to flotation of cassiterite from the Catavi, Bolivia, slime tailings has recently been described(3). The investigation which led to this successful process development included studies of other samples of gravity plant tailings as well as of lode tin ores. A common flowsheet with few significant variations was applied to most of these ore samples with acceptable results. In the following the process is described and the results of its application to samples from Bolivia and elsewhere given. Among the factors considered are: gangue depression, particle size and slime effects, and reagent and pulp density levels.

Jan 1, 1971

By H. Simpson

Middelburg mine is an opencast export mine operating in the Eastern Transvaal Coalfields of the Republic of South Africa (Figure 1). The mine was commissioned in 1983, to its original design capacity of 4.25 million sales tonnes which was subsequently raised to 5.5 million sales tonnes in 1989. This increase in export tonnage was brought about through an increase in the mines export allocation and the revision of management strategies. The maintenance of this increased tonnage with minimal additional capital has been achieved through improved operational efficiencies and the upgrading of planning operations through the purchase of an Enhanced Mine Scheduling Software Package (EMSSP/MINESTAR). Simultaneously with this requirement were additional factors that contributed to the implementation of the EMSSP. The mine was owned by a joint venture of two partners and is operated by Middelburg Mine services (Rand Mines Pty. Ltd) (Figure 2). This structure of ownership required the evaluation of numerous planning options to be under-taken concurrently and hence the need for an efficient streamlined scheduling pack-age that could fulfill this requirement. Compounding the EMSSP needs further, were the problems experienced in the export market, these being the external pressure from current and new suppliers in the market place which obliged management to provide solutions to rapidly changing market conditions. These fluctuating market conditions have had a direct effect upon the mine's planning strategies because of the large percentage of the mine?s sales sold on the international spot market. The sanction factor for all South African exporters has had a negative effect upon price and this was compounded further through internal competition in 1987 via suppliers attempting to maintain the market position.

Jan 1, 1991

By Robert R. French

Commercial grade gypsum beds up to 16 feet thick is present in southwestern Indiana. The major deposits are found at a depth of 350 feet to more than 500 feet below the surface. The ore body averages about 75 to 95 percent gypsum. Two companies are currently exploiting a deposit which underlies an area of several square miles near Shoals, in Martin County. Another deposit has been located in southwestern Owen County but has not been developed. The Indiana Geological Survey is currently drilling in Greene County and is considering further exploratory work in Perry end Dubois Counties.

Jan 1, 1965

By E. Viet Howard

During the recent expansion of precipitate copper production at the Chino Mines Division of Kennecott Copper Corporation, Santa Rita, New Mexico, local studies of the dump leaching process were intensified. As these studies progressed it became apparent that a reliable method for locating leach solutions within the dump was required, since the contact between leach solutions and the copper-bearing material would determine, in great part, the recovery of values. In the past, the problem of determining leach solution contact has been attacked by various methods, including destructive testing (dump dissection), indirect observation (such as chloride or dye tracers), and mathematical or laboratory model studies. These methods have not proved completely satisfactory for the studies now being developed. Investigation of methods for in situ observation of leach solutions led to consideration of radiation logging in drill holes, which are petro¬leum exploration and development techniques for locating fluids and measuring porosity in the subsurface. Standard oil field logging equipment was leased, modified, and tested. After successful testing, the equipment was purchased for additional studies. Applications and results of the methods are described in this paper.

Jan 1, 1968

By M. Govinda Raj, S. Sridhar, M. Aruna

Hand-transmitted vibration (HTV) exposure is associated with various health risks for operators of mobile mining equipment (MME). The case–control research was conducted to determine the musculoskeletal disorder (MSD) risks associated with exposure to HTVs in the exposed (case) and non-exposed (control) groups. HTV readings were measured at the interface between the hand and the steering device using the SV 105B triaxial hand accelerometer connected to the SV106 human vibration analyzer involving 40 MME operators in accordance with ISO 5349:2001 guidelines. A questionnaire survey was also carried out among both the study groups using Cornell Musculoskeletal Discomfort Questionnaire. The European Union's 2002/44/E.C. was used to assess the health risks posed to the MME operators. Twenty-eight out of the 40 MMEs were generating HTVs exceeding the stipulated daily limits of vibration, putting 70% of the operators at increased risk for developing MSDs. The case group was found to have an elevated risk of exposure with odds ratio (OR) 7.56 (95% confidence interval (CI), 1.159, 49.39) and OR 12.80 (95% CI, 2.436, 67.285) times more likely than the control group to suffer discomfort in the left shoulder and left wrist, respectively, indicating increased risk of exposure to HTV. Additionally, cases had elevated risk associated with exposure to tobacco, OR 9.35(95% CI, 1.856, 47.129) compared to those who did not use tobacco. MSDs were more prevalent in the case group compared to the control group. This observation was validated by the field investigations and the responses of MME operators to the questionnaires.

Aug 2, 2022

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Morgana Rosset, Bárbara da Rocha Pereira

High-purity alumina finds application in various electronic industry sectors, with approximately 100 million tons of this compound being produced worldwide. Alumina is acquired through the mining process of bauxite, a rock composed of a mixture of minerals such as gibbsite, kaolinite, hematite, and either anatase or rutile. In 2020, both bauxite and alumina were included in the list of critical raw materials. Due to the demand for high-purity alumina production, the development of a methodology to remove impurities present in the leach liquor from bauxite processing by solvent extraction (SX) followed by precipitation has been widely studied. This work aims to obtain high-purity alumina from bauxite by a solvent extraction process followed by a precipitation step from the sulfur leach liquor obtained by the thorough dissolution of Al and Fe from bauxite. Different parameters were evaluated in the SX step, such as extractant type, pH, temperature, and volume-to-volume ratio. The results indicated that using Alamine 336 as an extractant at pH 0 and room temperature led to an extraction of 90% of Fe and 15% of Al. Aluminum sulfate was completely precipitated as aluminum hydroxide and 55% of Fe using NH4OH. After the calcination procedure, obtaining a 99.9% pure alumina was possible without generating a red mud-similar residue.

Dec 28, 2023

By Tyler Lahti, Peter Borgacci, Mary Jane Ferraro, Prakash Nadesparan

Toronto Tunnel Partners (TTP), under contract to Metrolinx/IO, is constructing new twin rail tunnels under the Highway 401 & 409 interchange to accommodate additional tracks to support the GO Expansion program for future two-way, all-day service. The new tunnels are being constructed using the Sequential Excavation Method (SEM) and utilize a tunnel pre-support system consisting of a series of 800 mm diameter steel pipes to form a pipe canopy. The pre-support pipes were installed with an Auger Boring Machine (ABM) in four separate headings; one heading from each of the tunnel end portals, and two from a shaft in the middle of the highway. To facilitate the auger boring operation, a custom steel reaction frame was required to counteract the thrust from the ABM at the portals, and a temporary shaft structure was installed in a narrow median space of the highway. The installation of the pipe canopy had to overcome challenges including removal of obstructions, alignment issues, and controlling settlements to the highway surface. This paper discusses the purpose of the pipe canopy, design and installation of the temporary shaft and structures to support the auger boring operation, the experience of the contractor during the installation of the pipes, and brief overview of the experience tunneling below the pipes.

Jun 13, 2021

By Anil K. Ray

Roof falls are one of the greatest hazards in underground coal mines worldwide. Due to stringent safety measures and extensive support system development, roof falls have been reduced significantly but they still persist in many underground coal mines. Some of the roof falls initiate with cutter roof or guttering. In the past, many factors have been identified as being responsible for the development of cutters and roof fall. These responsible factors can be broadly classified as stress related or non-stress related. In this paper the finer details of mining technique have been taken into consideration for better understanding of cutter roof and roof fall problems. Three dimensional finite difference modeling has been used to explain the mechanism of cutter development. Strain softening material behavior has been used to realistically simulate the cutter formation, and common cutting sequences as implemented in the field have been simulated. This was done with an objective to determine whether the cutting sequence has really any significant control over cutter formation or not. In addition to cutting sequences, the effect of cut length is also studied. The effect of step cutting and turning of crosscut into and away from major and minor horizontal stresses is also examined to see its influence on cutter development.

Jan 1, 2009

By C. N. Savage

An industrial minerals review involves an attempt to assemble field and statistical data which are obscure, elusive and incomplete. Often, when me statistical data are available, combining or lumping of commodity values conceals the value of specific items. Personal knowledge of the minerals known to occur in the area of concern, combined with whatever available published data may be compiled, together with careful use of several extrapolation methods, may yield an acceptable summary review of the industry. However, it is particularly hazardous to speculate on future trends and economic aspects because of the many unpredictable variables which may affect the industrial minerals business. Among these variables are the effects of diverse geological conditions, the impact of technological changes (including new uses for minerals not formerly considered industrial types), changing socio-economic factors (including growing environmental controversy), use of substitutes and even recycling of some of the industrial minerals (for example, building materials, lime, etc.). My main objectives are to reveal, as accurately as I can, the state of the in¬dustrial minerals situation, and the effects of possible future developments on this industry in Idaho. Where the words...industrial-tyke minerals, .are used in this discussion, reference is made to selected metallic and nonmetallic minerals and related materials, as well as rock (Table I). Industrial minerals known to be present in Idaho may be listed under general use categories as in Table 1. Some of these commodities are being marketed, have been marketed in the past, or occur in potentially marketable quantities. Mineral fuels are neither mentioned, nor are they considered important in Idaho. Based upon our present knowledge and lack of known, economically valuable occurrences of these commodities, they are considered insignificant (Idaho Bur. Mines and Geology, 1964). Information used for this study is from several sources. Most of the statisti¬cal information should be credited to the U.S. Bureau of Mines Minerals Yearbooks,

Jan 1, 1971