Search Documents

Invensys’ recently introduced Field Device Manager for Foxboro I/A Series distributed control systems provides the industry’s first solution that takes advantage of both the latest Enhanced Electronic Device Description Language (Enhanced EDDL) and FDT technologies. This combination provides comprehensive lifecycle support to configure, calibrate, commission, diagnose and optimize the performance of any vendors’ foundation fieldbus device. The I/A Series Field Device Manager enables users to take advantage of any EDDL, Enhanced EDDL and/or FDT host deliverables supplied by the device vendor.

Jan 1, 2007

By Jacob Carr, Chenming Zhou, Nicholas Damiano, James Noll, Jingcheng Li

Machine-related injuries are one of the major safety concerns in underground coal mines. Severe injuries and fatalities occur when a miner is struck, crushed, or pinned by mining equipment such as a continuous mining machine (CMM), shuttle car, or a scoop. Proximity detection systems (PDSs) have been applied in mining to reduce these types of injuries and fatalities. All of the PDSs that are currently approved by the Mine Safety and Health Administration (MSHA) for use in underground coal mines are magnetic-field based and could be affected by metallic objects such as trailing cables. Researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated the influence of trailing cables on the performance of PDSs. In particular, the magnetic field coupled from proximity system generators to a de-energized trailing cable was characterized. The results show that significant energy can be coupled from the proximity system generators to a trailing cable when there is a closed loop in the cable. The effect on PDS performance from the magnetic field radiated around an energized trailing cable was also quantified for different current amplitudes in the cable. It is shown that the magnetic field caused by the electric current in the trailing cable mainly consists of a 60-Hz signal and its harmonics which causes little interference to the PDS. The results presented in this paper can help PDS manufacturers to design better systems that are more immune to these effects.

By Enrique Fernandez

M-30, Madrid’s inner ring, covers 42 sq km of the city centre where one million people reside. It was constructed in several phases during the sixties and the eighties. The design criteria applied to those phases were different and were not always homogeneous with urban roads with lighting regulation as well as speedways. These areas had a heavy concentration of access and exits and there had been made many changes on the number of traffic lanes which has caused heavy traffic congestions and high accident rates. The environmental impact and noise pollution in residential areas are also consequences of M-30. The Madrid Major took a decision at the beginning of the present legislation, based on socio economic and environmental evaluation; rebuild the M-30 with the following sustainable mobility principles: Underground transfer of a considerable portion of the main ring and some of its links replacing some parts of the surface with new green areas in order to reduce the environmental impact. Increase the traffic capacity, improving the traffic continuity and fluidity and eliminating the lighting regulation areas, which is one of the main congestion problems currently. Increase the traffic safety with clear signalling information panels and avoiding difficult maneuvering. Redesign the links with the high capacity radial highways and other connecting lanes of the city. The project is worth 3.7 billion Euros. In 2007, when the construction is completed, it is expected will save 14 million of journey hours that represent 4.5 million Euros saved in fuel consumption per annum, There will be a very significant reduction of 35,000 tons of CO2 in terms of pollution and 400 less car accidents. Those values will increase even more in the following years. The areas beside Manzanares River, running parallel to the M-30 on the western side of Madrid, will be highly enhanced. Better water quality and the recovering of the green areas existing in old times will also return for the citizen’s enjoyment. TUNNEL CROSS SECTION OF CALLE 30 SOUTH BY PASS One of the major challenges of the new Calle 30 is actually not only the related to the main road but also to the link with the A-3, with highway to Valencia. This link is currently the most congested area and has one of the highest traffic densities of Spanish roads, with more than 250,000 vehicles/day. The remodelling of this area is the principle objective of the South by-pass. The tunnel is the only answer for this by-pass as the road alignment will go among buildings. A twin tube design, one for each direction, with three lanes allowing the circulation of both, light cars and heavy trucks, is the solution that has been

Jan 1, 2007

Gary R. Steele is vice president, corporate marketing with Energy Fuels Resources. As such, he knows the global uranium market. The following are some of his thoughts on uranium?s place in the global energy picture. ME: What are Energy Fuels Resources? thoughts on the global nuclear power industry? Steele: The global nuclear power industry is a major contributor to the electrical needs of the world. Though generation by nuclear reactors has primarily attracted attention through the reactor accidents at Three Mile Island and Chernobyl, nuclear power continues to quietly and safely provide power to a growing and power-hungry world population. As of March 2008, 30 countries were operating 439 nuclear power reactors. Nuclear power plants provided about 15 percent of the world?s electricity production in 2007. France leads the world in nuclear utilization, with 77 percent of its power coming from nuclear plants. And Lithuania, Slovakia and Belgium each derive more than 50 percent of their power needs from nuclear plants. For much of the developed world, nuclear generation has already been contributing significantly to the supply of electricity. Additionally, 34 new nuclear plants are under construction in 14 countries. Leading the rush to build new nuclear generating plants are China, Russia and India. Each of these countries is building six new nuclear power plants. These 18 plants, totaling almost 12,000 MW of generation capacity, will require about 7.25 kt (16 million lbs) of U3O8 for their initial fuel load and will consume about 2.45 kt/a (5.4 million lbs/year) for the rest of their operating lives. The rest of the world, outside of the United States, has used nuclear power as a viable and economic generation alternative since the commercialization of utility nuclear reactors. And current activity supports the strong future of the nuclear alternative internationally.

Jan 1, 2008

By Mark P. Juzli

During the 1980s, a revolution has been taking place in industrial minerals marketing. Transportation deregulation and a handful of creative marketing and distribution managers have completely changed the rules for marketing many industrial minerals. Minerals are being transported much farther than in prior decades and at much less cost. Bulk and package terminals are becoming increasingly common as a means to take advantage of freight rate savings and to provide enhanced service to faraway customers. Water and rail transportation are being used increasingly to penetrate markets considered unreachable just a few years ago. No longer do the textbook rules of thumb for industrial minerals marketing apply. This author recalls three of those rules he was taught in mineral economics graduate school in the 1970s. As recorded in class notes: • construction aggregates are seldom shipped more than 32 km (20 miles) from the quarry; • cement is sold within 240 km (150 miles) of the mill; and • industrial sand is sold regionally - it is freight constrained to a market radius of no more than 320 to 400 km (200 to 250 miles) from the plant. And yet, the author looks up in 1989 and observes overland movements of aggregates of many hundred miles, overland movements of cement and industrial sand of 1600 km (1000 miles) or more, and water movements of both aggregates and cement into the United States from sources halfway around the world. Truly, industrial minerals are in the midst of a marketing revolution. The companies that have led this revolution have enjoyed considerable financial success in the 1980s. They have enhanced their profitability by increasing market share, capacity utilization, and average selling prices by taking product to remote markets where premium prices are available. They have consistently outperformed their competition, many of whom remain unaware that the marketing revolution going on around them is actually a transportation/distribution revolution. The successful industrial minerals company of the next 10 to 15 years must participate in the transportation revolution as it continues to evolve. Additional human and capital resources must be committed to maximize the effectiveness of a company's transportation and

Jan 1, 1989

By D. Potter

In 1990, Freeport Exploration began regional reconnaissance exploration programs in Irian Jaya, the easternmost province of the republic of Indonesia (Fig. 1). Irian Jaya occupies the western half of the island of New Guinea. Freeport was awarded an initial contract of work that totaled 2.6 million hm2 (6.4 million acres). The company was subsequently awarded additional concessions that added 1 million hm2 (2.5 million acres). The concessions require work commitments and periodic relinquishments. Due to these relinquishments, Freeport’s current land position totals 1.9 million hm2 (4.7 million acres). Freeport began the exploration program to locate additional Grasberg deposits, the largest deposit in the Ertsberg district. But the company recognized that other types of deposits could be present in the largely unexplored area of Irian Jaya.

Jan 1, 1999

By A. Noble, R. Q. Honaker, J. Werner

Recovery of rare earth elements (REE) from coal-related resources has recently received significant interest due to supply concerns and their key roles in critical industries and defense-related technologies. An integrated flowsheet consisting of sorting, crushing/grinding, physical separation, acid leaching, solvent extraction, and selective precipitation was designed to achieve continuous production of rare earth products from various coal-related resources such as coarse refuse and acid mine drainage. A pilot plant was constructed that enabled continuous testing of the circuitry on a range of different coal-based feedstocks. Despite achieving significant success in producing high-grade rare earth oxide products, low REE recovery values and high operational costs necessitated a re-evaluation of the process flowsheet. This article describes the circuitry improvements that were based on both laboratory and pilot plant test results. Roasting as a pre-leach treatment was found to significantly improve the leaching rate and overall REE recovery values. After roasting West Kentucky No. 13 and Fire Clay coal refuse materials at 600 °C, REE recovery increased by 60 and 40 absolute percentage points, respectively. Rare earth concentration in the pregnant leachate solution (PLS) was increased to around 700 ppm prior to solvent extraction using a staged precipitation method. REEs in the precipitate were re-dissolved, purified, and extracted from the PLS using solvent extraction and selective precipitation to values of around 80%. As a result of the improvements, chemical consumption in the acid leaching and solvent extraction processes was significantly reduced. A techno-economical assessment of the improved flowsheet indicated significant commercialization potential.

By A. Noble, R. Q. Honaker, J. Werner

Recovery of rare earth elements (REE) from coal-related resources has recently received significant interest due to supply concerns and their key roles in critical industries and defense-related technologies. An integrated flowsheet consisting of sorting, crushing/grinding, physical separation, acid leaching, solvent extraction, and selective precipitation was designed to achieve continuous production of rare earth products from various coal-related resources such as coarse refuse and acid mine drainage. A pilot plant was constructed that enabled continuous testing of the circuitry on a range of different coal-based feedstocks. Despite achieving significant success in producing high-grade rare earth oxide products, low REE recovery values and high operational costs necessitated a re-evaluation of the process flowsheet. This article describes the circuitry improvements that were based on both laboratory and pilot plant test results. Roasting as a pre-leach treatment was found to significantly improve the leaching rate and overall REE recovery values. After roasting West Kentucky No. 13 and Fire Clay coal refuse materials at 600 °C, REE recovery increased by 60 and 40 absolute percentage points, respectively. Rare earth concentration in the pregnant leachate solution (PLS) was increased to around 700 ppm prior to solvent extraction using a staged precipitation method. REEs in the precipitate were re-dissolved, purified, and extracted from the PLS using solvent extraction and selective precipitation to values of around 80%. As a result of the improvements, chemical consumption in the acid leaching and solvent extraction processes was significantly reduced. A techno-economical assessment of the improved flowsheet indicated significant commercialization potential.

By Keith Bowers, Frank Mimnagh, Eddie Woods

The CTRL London Tunnels The Channel Tunnel Rail Link (CTRL) London Tunnels comprise 36km of internal diameter bores that were driven by Earth Pressure Balance (EPB) Tunnel Boring Machines (TBMs). The tunnels were constructed between the autumn of 2002 and the spring of 2004. The permanent works also included the 1.1 km long station box at Stratford, five ventilation shafts of depths between 30 and 54 m, 29 cross passages and various large diameter sprayed concrete lined connecting tunnels. The tunnels were driven under densely populated areas of north and east London, as depicted in Figures 1 to 4. Under the parliamentary CTRL Act the project had obligations to make

Jan 1, 2005

By D. Craig Camp

conditions. The soils included 65 m of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2, 130 meters of soft clay, silt, and sand not exceeding 30standard penetration test SPT blows per 300 mm, and 220 m of rock ranging between an UCS of 400-600 kgf/cm2. The river crossing, utilizing 1778 mm OD x 19 mm wall x600 mm steel casing pipe without intermediate jacking stations, was part of a seven kilometer liquefied natural gas (LNG) transmission line in South Korea. This 440-m, 1,442-ft, river crossing was microtunneled through three different ground conditions and completed in just over three months. The crossing was achieved with an average of 25 m of ground cover and 15 m of water cover. The Kwang Yang River Crossing was part of a 7 km liquefied natural gas pipeline project for POSCO, a Korean steel producer. The microtunneling machine was custom built for this project. The microtunneling machine selected for this project was tooled with 7 button bits and 2 roller bits. None of the cutter bits were replaced during the drive. Inside the machine, before the spoils laden slurry was pump back to the surface, it would pass through an independent cone crusher. The crusher is placed in the slurry flow to make sure that none of the spoils are so large as to stop the return flow of the slurry. An additional requirement was for the inclusion of a compressed air lock. The air lock was required in the event that the cutter tools required replacement. The cutters were back loaded so that the workers would have access to change the cutters in the event of cutter failure or wear out. No intermediate jacking stations were installed for the drive. The soils included 65 meters of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2 with production averaging between 7 and 20 mm/minute. The second zone contained 130 meters of soft clay, silt, and sand not exceeding 30 standard penetration test (SPT) blows per 300 mm with production averaging between 80 and 180 mm/minute. The third zone contained 220 m of rock ranging between an UCS of 400-600 kgf/cm2 with production averaging between 7 and20 mm/minute. The steel casing pipe was 1778 mm OD x 19 mm wall x 6000 mm long. The project profile, see Figure 1, shows the soil conditions. The hand written numbers locate just above the pipeline are the production dates. The circled numbers are the 10 pipe joint increments. The project required 74 pieces of pipe to span the440 m drive. Figure 2 and Figure 3 are the jacking information. Figure 3 is a continuation of the information from Figure 2. The top section of the graph is the jacking force. The jacking

Jan 1, 2001

By Kerry Gee, Gary Colgan, James Fricke

Introduction Elevated zinc concentrations are observed in groundwater within alluvium adjacent to Silver Creek east of Park City, Utah. The study area is located in a small valley one and one-half miles northeast of Park City, Utah in Summit County, Utah (Figure 1). Although surface water concentrations in Silver Creek are typically less than 1 mg/l, groundwater concentrations have been measured as high as 85 mg/l in a near neutral pH environment. The elevated zinc concentrations in groundwater result from several factors including: (1) dissolution of zinc from tailings exposed at the surface and within the alluvium, (2) oxidizing conditions created by surface/ground-water exchange, and (3) ideal geochemical conditions for the dissolution of zinc-containing minerals. These ideal conditions include readily soluble minerals, available anions for complexation, and lack of available surface adsorption sites.

Jan 1, 2005

By A. Fuerst

The recent seismic events have shown that earthquakes have an immense destructive power. Chile was hit in February 2010 with a seismic intensity of 8.8 on the Richter scale, and had loss of about 700 killed persons, while Haiti was hit in January 2010 with 7.0 killing about 220?000 people. The event in Haiti showed that the seismic events can lead to a disaster if no preventive measures are taken. On the other side, the seismic event in Chile has hit a well-prepared country with moderate consequences. The earthquake with 6.6 Richter in Japan in March 2011, have further shown how severe the consequences can be if critical equipment is involved. Fortunately, the equipment in a mine has not the potential hazard as a nuclear power plant. Anyway, we are diligent and it is obvious that the seismic risk may lead to a real disaster even if the probability is small. The GMD is an important component in the grinding circuit of a mine. This paper maps out earthquake-prone areas including expected earthquake magnitude calculated according to relevant standards, focusing mainly on the building code IBC 2009. An overview is provided on how this standard is applied to mining equipment to minimize damage and aid large mills in operation to successfully withstand seismic effects. The differences in stresses and forces on the GMD and foundation are shown based on a turning and stopped mill simulation during an earthquake. The results demonstrate the need to maintain active and operating earthquake detection systems. Aside from detecting an earthquake?s magnitude, the sensor information can also be used to reduce the harmful effects that an earthquake has on mining equipment. As follows the earthquake requirements are defined. The last part of this paper explains how to fullfill these requirements.

Jan 1, 2012

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at tem¬peratures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Forma¬tion changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite.

Jan 1, 2007

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at temperatures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Formation changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite. © 2007 Elsevier Inc. All rights reserved. Keywords: Biwabik Iron Formation; Duluth Complex; Mineralogy

Jan 1, 2007

For the past four years, the Department of Mining Engineering at the University of Kentucky has conducted a validation study of the CFD Fluent code, by comparing its results against mining-related benchmark experimental data provided by NIOSH?s Pittsburgh Research Laboratory. This particular study is dedicated to the effect of machine-mounted dust scrubbers on the performance of face ventilation systems using extended-cut mining with a blowing curtain.

Jan 1, 2009

By R. L. Wiegel

Several mineral process modeling and simulation packages are currently available for use in evaluating the performance of alternative process flowschemes. A critical link that has been missing from these packages is the ability to quantitatively model the effect of size reduction on the liberation of the valuable and waste minerals in the ore being processed. Although there have been several approaches taken to this problem over the past 25 years, none has led to a satisfactory conclusion. A technique has been developed for measuring the effective liberation characteristics of magnetic taconite ores, and a program has been constructed which makes use of these liberation characteristics in simultaneously simulating both size reduction and mineral liberation as it occurs in tumbling mills. This is an especially important step in the modeling of magnetic taconite processes, where magnetic rejection of low grade wastes between grinding stages mandates that a predictive capability be available. The current application is specific to magnetic taconite, but it is possible that a similar approach could be used for other types of mineral systems.

Jan 1, 2002

By John Addison

Experimental animal studies comparing asbestos and non-asbestos varieties of tremolite indicate tremolite asbestos is markedly more carcinogenic. By direct analogy, the differences in carcinogenicity between tremolite asbestos and non-asbestos prismatic tremolite should be the same for the other types of amphibole that also crystallize in the asbestos and non-asbestos habits. The earliest of the experiment animal studies, done more than 25 years ago, have design limitations by modern standards including the use of injection or surgical implantation as the route of administration rather than the more relevant route of inhalation. However, the differences in the carcinogenicity of amphibole asbestos and non-asbestos amphiboles are sufficiently large to be clearly discernable even with the study limitations. Together with later studies on these and related minerals, there is strong evidence of a much lower hazard associated with the shorter, thicker fibers of the non-asbestos amphiboles, than is found for the asbestos analogues of the same mineral. It is possible that the non-asbestos amphiboles are no more hazardous than other silicate minerals widely considered nuisance dusts. © 2007 Elsevier Inc. All rights reserved. Keywords: Amphibole; Asbestos; Tremolite; Carcinogenic

Jan 1, 2007

By G. Danko

MULTIFLUX, a new thermal, hydrologic, and airflow model and software is being developed to solve the flow of heat, moisture, and air in and around an underground opening. MULTIFLUX couples two distinct domains that are solved separately first and re-coupled as an iterative task: (1) the rockmass, and (2) the airway. The airway is solved with a lumped-parameter Computational Fluid Dynamic (CFD) module which is an embedded part of the MULTIFLUX code. The CFD model includes convection, conduction, and radiation for heat, as well as convection and diffusion for moisture transport in an air-filled opening. The CFD model also solves for the airflow field. The surrounding rockmass model may be from any analytical solution, or from a complex thermal-hydrologic numerical model such as NUFT or TOUGH2. The rockmass model is interfaced to MULTIFLUX using a novel technique called Numerical Transport Code Functionalization (NTCF). The method provides fast convergence on a personal computer platform. The paper reports the results of MULTIFLUX simulations for a mine drift, comparing calculations with a known mine climate software, CLIMSIM, and with measured data. Through this validation example, the performance of MULTIFLUX is demonstrated. The results show excellent agreement due to the use of realistic modeling assumptions and boundary conditions.

Jan 1, 2009

By Werner Burger

Earth Pressure tunnel boring machines are tackling difficult ground conditions that five years previous were not considered feasible. The technology has evolved that allows EPB TBMs to cross into areas that with the latest in conditioning and special design considerations are now possible to mine. This paper will review the various recent developments and those projects where these new techniques have been applied.

Jan 1, 2008

By Mitchell L. Fong

The Bay Area Rapid Transit (BART) District will be extending BART service south along an 8.7-km (5.4-mile) -long corridor in the city of Fremont, California as part of the Warm Springs Extension (WSX). The WSX project will link the existing BART system to the future BART to San Jose extension. A segment of WSX is located in Fremont Central Park (referred to as the Fremont Central Park Subway Project). The Fremont Central Park Subway is considered the most complicated and geotechnically challenging portion of the project with an underground subway box being constructed near the active Hayward Fault which is capable of ground motions up to 0.75 g and is located in an aquifer which is used for water storage and supply. Soil-structure interaction analysis was used in the design of the subway box to resist deformations due to earthquake ground motions. A water-tight excavation support system has been designed to allow subway box construction while minimizing impacts to the aquifer.