Search Documents

By W. I. Enderlin, P. O. Jackson, J. A. Glissmeyer, K. B. Olsen

A reliable estimate of radon emissions to the environment from underground uranium mines was obtained through measurements of radon in ventilation air at 24 mines and from estimates of radon release from other mine sources. The total production of U308 from the mines sampled represents about 63% of the total U.S. production from underground mines (1978 statistics). Wide variation in the radon emission rate per unit of production was found from mine to mine. Using the total radon emitted and U308 produced by all mines sampled, an average of 26.7 Ci of radon was emitted per ton of U309 produced. The investigation includes a brief study of the sources of variation of the emission rates. A statistically significant relationship was found between the measured radon release rate and the cumulative ore production at several mines.

Jan 1, 1981

By Jeff Poe

When a takeup weight is offset to the side of a conveyor, a wire rope is commonly routed from the takeup weight through a series of sheaves to the takeup carriage. The friction developed from a series of wire rope sheaves can effect the actual belt tension at the make up carriage. Through real-mime testing the actual tension on a makeup carriage was recorded with data acquisition using an internally strain-gauged turnbuckle. The wire rope used to transfer the makeup weight to the makeup carriage was routed through a series of lubricated bronzed bushed sheaves. The tension on the makeup carriage was found to be as much as 26% higher than the weight of the makeup due to the friction in the sheaves. A detailed discussion of the testing and results will be made.

Jan 1, 2000

By D. D. Runnells, G. A. Doyle

The quality of water in mine pit lakes depends in part on the physical limnology, including such factors as thermal and chemical stratification, turnover and the development of anoxic conditions with depth. Limnologic data collected from four existing pit lakes in Montana and Saskatchewan indicate that pit lakes develop a thermocline (temperature stratification) in the upper 10 to 30 m (33 to 100 ft) of the water column. Two of the pit lakes, 26- and 55-m (85and 180 ft) deep, undergo seasonal turnover of the entire water column, whereas two deeper pit lakes, 110- and 240-m (360- to 790 ft) deep, undergo seasonal turnover of only the upper portion of the water column. In the deeper lakes, seasonal mixing does not extend through the entire water column, and a distinct chemocline develops with depth.

Jan 1, 1998

By Roger D. Sharpe

Oklahoma contains extensive resources of high-purity gypsum that were deposited in the Anadarko and Hollis basins during Permian time. The gypsum resources and reserves are estimated to be about 48 billion short tons and a; located in the western portion of the state. Oklahoma is the largest producer of gypsum products in the United States. The Blaine Formation and the Cloud Chief Gypsum contain several beds of minable thickness. Four stratigraphic units in the Blaine Formation are quarried in Oklahoma. The Shimer, Nescatunga, and Medicine Lodge Members are quarried in northwest Oklahoma. The Van Vacter Member, consisting of three gypsum beds, is quarried in southwest Oklahoma. The Cloud Chief Gypsum is quarried in the west-central part of the state. The gently dipping gypsum in the Blaine Formation generally crops out along low escarpments and is covered in the downdip direction by increasing overburden, consisting of sand, shale, and/or dolomite. Anhydrite occurs in the downdip direction under the thicker overburden. The Cloud Chief Gypsum crops out as hills, which are eroded remnants of a more widespread, massive sulfate unit. All of the gypsum produced in Oklahoma is extracted using quarrying methods. A variety of products are made from gypsum quarried in Oklahoma. The products are manufactured from uncalcined, calcined, and deadburned gypsum. Products vary from raw, ground gypsum used for agriculture, to high-value-added industrial plasters, cements, and fillers produced from calcined gypsum. A sampling of the many products manufactured from Oklahoma gypsumincludes: (1) agricultural-soil amendment; carrier for insecticides, pesticides, and herbicides; calcium supplement in animal feeds; (2) gypsum wallboard-common, fire-resistant, and water-resistant varieties; (3) industrialgypsum plasters-art and casting, pottery and ceramic, molding and tooling, crayons, wall patching; (4) industrial gypsum cements-oil-well cement, high-strength statuary, high-strength tooling, fiber-reinforced architectural, road and bridge repair; (5) food and pharmaceutical-filler and binder in aspirin and other medicines, yeast activator in brewing of beer, moisture absorbent in bread and pizza dough; and (6)portland-cement retarder-ground with clinker to control setting time.

Jan 1, 1999

By H. Wagner

Recently a detailed study ?Minerals Planning Policies and Supply Practices in Europe? has been completed. The study, conducted on behalf of DG Enterprise, demonstrated that there are very few written down national minerals policies within European Union. Mineral policy elements are dispersed in many different documents and acts. The paper discusses the essential elements of minerals policies; particularly importance is placed in issues related to planning (land use planning, mineral development, etc.). A number of examples of successful and less successful mineral planning policy approaches are presented in other to support the idea of importance of comprehensive mineral policy. The main sources of information were the country reports of 26 European countries that are appendix of the study. We conclude that comprehensive written mineral policy that incorporates essential elements is crucial in order to achieve secure minerals supply.

Jan 1, 2007

By B. Waterman, D. Ramey, L. Schlink

"Water is a primary commodity for most industrial processes. It has become a global focus in light of climate change and population growth. Reuse of process water has two major benefits - minimize the amount of fresh water added now and minimize the amount of discharge water that requires treatment later.Mining and mine product processing has its share of reused water. For example, reclaim water from a tailings impoundment, overflow from thickeners and leach solution to raffinate and back again all demonstrate the use and reuse of water in mining circuits. Eventually, a mine reduces production or ceases operations completely, eliminating the option to reuse the impacted water and, thus, requires treatment of the remaining water.Current methods of water treatment remove the impacts, providing clean water for discharge, but leaves behind a concentrated waste that requires further treatment or disposal of a hazardous waste. Freeport- McMoRan is currently testing three water treatment technologies specific for sulfate and/or metal removal from mine impacted water with the approach of transformation not concentration. These technologies provide clean water for alternative use while creating byproducts that could be marketable, or disposed as a nonhazardous material, thereby reducing the cost and longterm liability of disposal.The selection of a water treatment process is site-specific. The volume of water, contaminant to be removed, disposal options, length of time for treatment, location of plant and reagents and discharge requirements are some of the factors that need to be considered when selecting a water treatment process. Common water treatment technologies for mine impacted water consist of low- or high-density sludge (LDS/ HDS), reverse osmosis (RO) and evaporative technologies. In addition to operating costs, these processes require additional handling of the concentrated sludge or brine. Advanced water treatment technologies include ion exchange, solvent extraction and metals precipitation with or without the aid of a biological system. Some of the more complex systems have a series of unit operations to achieve required discharge regulations."

Jan 1, 2014

By Manoj Khandelwal, Jian Zhou, Yingui Qiu, Peixi Yang, Pingan Peng

Rockburst prediction is crucial in deep hard rock mines and tunnels to make safer working conditions. Due to the complex interaction of many factors involved in rockburst prediction, such as multi-variable and multi-interference factors, three hybrid support vector machine (SVM) models optimized by particle swarm optimization (PSO), Harris hawk optimization (HHO), and moth flame optimization (MFO) are proposed to predict rockburst hazard level (RHL). The RHL is determined according to four kinds of microseismic characteristic parameters including angular frequency ratio, total energy, apparent stress, and convexity radius. Then, six types of microseismic characteristic parameters are taken as input variables in 343 sets of data, including angular frequency ratio and total energy, etc.. And the RHL is taken as the output target of rockburst prediction. The classification performance of PSO-SVM, HHO-SVM, and MFO-SVM hybrid models is evaluated by accuracy (ACC), precision (PRE), and kappa coefficient. Findings reveal that the MFO-SVM model performs best in terms of accuracy, with ACC, PRE, and kappa coefficients reaching 0.9559, 0.9063, and 0.9094 respectively, while PSO-SVM and HHO-SVM have similar performances. However, the PSO-SVM, HHO-SVM, and MFO-SVM all perform better than the unoptimized SVM model. This confirms that the three optimization algorithms significantly enhance the rockburst prediction capacity of the SVM model to help mine practitioners apply machine learning methods to rockburst prediction problems appropriately.

Feb 3, 2023

By Joseph A. Dos Santos

"The subject of this writing was first published in 1998 with the emphasis on the hardware cost comparison. Other costs, such as the required land area and spatial volume, were mentioned but not emphasized, as these were not deemed as important for new projects where the space was appropriated as required. During the last decade, these other costs have proven to be more than equal in importance. These costs are emphasized here through specific accounts of actual highangle conveyor installations that demonstrate the importance and the high-angle advantage An update on the progress in sandwich belt highangleconveyor technology is also provided.Origin and progress in sandwich belt conveyorsCover belts of the 1950s. Large volume, highangle conveying by “conveyors with cover belt, dates back to the early 1950s, when such systems were employed at the bucket wheel excavator boom conveyor in German lignite mines to increase the depth of cut without increasing the boom length. Various systems were developed, patented and built. These systems were not a lasting success for various reasons, which are noted by Rasper[1]. In his 1958 “Review of Cover Belt Systems,” Rasper summarizes the characteristics which are worth pursing and those that should be abandoned. The former are akin to good conveyor engineering. The sandwich belt conveyor model. The first sandwich belt conveyor model allowed calculation of the required hugging pressure to develop the bulk material’s internal friction and preclude material slideback. A modern, accurate version of the sandwich belt conveyor model is presented in Fig. 1. This model depicts accurately a derating of the material cross-section allowing an ample belt edge distance that can tolerate normal belt misalignment without material spillage. The calculations must thus recognize that only part of the hugging pressure is imparted onto the material with the remainder transferred belt edge to belt edge affecting a material seal. Mathematical development of the sandwich belt model is covered by Dos Santos and Frizzell in their 1983 article, “Evolution of Sandwich Belt High Angle Conveyors.”"

Sep 1, 2016

By Ali Kazmi, Wern-ping N. Chen

A load rating procedure was performed to evaluate safe load capacity of the Port of Miami Tunnel (POMT), FDOT Tunnel No. 871071 SR 887. The rating procedure performed on a total of eleven stations beneath roadways and with fill depth less than the tunnel exterior diameter (42 ft). Calculations on tunnel sections passing beneath roadways were performed to evaluate the structural response of the sections subject to moving vehicular loads, dead load, and earth pressures. Ratings were performed in accordance with AASHTO and FDOT guidelines. The procedure considered two types of vehicles (HL-93 and FL-120) and two rating levels (Design level and Permit level). As part of HL-93 vehicle, Tandem load was also considered for rating, separately. For HL-93 and HL-93 Tandem, inventory and operating level ratings were performed. The results show rating factors are high. The minimum rating factor is 16.8 using Inventory truck HL-93. For Permit level using FDOT FL-120 truck the minimum rating factor is 6.9. As can be seen, rating factors are higher than comparable analysis for bridges. This paper explains how the procedure can be implemented for tunnels and evaluates the rating results.

Dec 1, 2022

By Robin J. Hickson

El Abra has mining concessions granting the right to exploit minerals in more than 130 km2 (32,122 acres). SCM El Abra owns “rights to occupy” the surface of these claims. The company also owns the surface rights over the process plant area and over land conveyor route. The project has procured all material easements relating to the mine area, processing facilities and access rights of way. Engineering, procurement and construction Figure 1 sets out the development and construction schedule for the project. Development is already well under way. As of early January 1996, about 70% of the project was complete and more than 80% of the capital expenditures were committed.

Jan 1, 1996

By Donald O. Rausch, William E. Hawkes, Odin Jr. Strandberg

INTRODUCTION Kennecott Copper Corp.'s Tintic Div. Burgin mine is a 725 t/d (800 stpd) lead-zinc producer, located in the east Tintic mining district, 5.6 km (3.5 miles) east of Eureka, and 130 km (80 miles) south of Salt Lake City, UT. The Burgin mining complex includes three shafts, shop, dry, and office facilities, and a 454 t/d (500 stpd) flotation concentrator. Production and ser¬vice entry to the mine is through a 4.26-m (14-ft) diam concrete-lined production shaft, and a three-compart¬ment rectangular shaft. A connection with the Apex No. 2 shaft and the Burgin mine provides a second exhaust airway. Bear Creek Mining Co., Kennecott's exploration sub¬sidiary, began exploration of the Burgin mine area in 1957 with the sinking of the 335 m (1100 ft) deep No. 1 shaft. A station was cut at the 320-m (1050-ft) level of the shaft and extensive drifting, diamond drilling, and some winzing and raising confirmed the presence of a major lead-zinc ore body, the main portion of which oc¬curred below a hot saline water table. Surface facilities and the 4.26-m (14-ft) diam concrete-lined production shaft were completed in 1966. Ore production has been steadily increased to 725 t/ d (800 stpd) since 1966. The collar elevation of the No. 2 production shaft is 1731 m (5678 ft) above sea level. The mine's three levels, the 1050, 1200, and 1300 are at elevations of 1414.6, 1356.4, and 1338.1 m (4587, 4450, and 4390 ft), respectively. The approximate elevation of the hot saline water table is 1382.6 m (4536 ft). The earliest production on the east Tintic mining district was from the Eureka Lilly mine in 1909. Later, in 1916, the Tintic Standard mine was discovered, and pro¬duced ores with a gross value of $80,000,000 through 1956. The Eureka Standard mine located 1.6 km (1 mile) southwest of the Burgin mine produced ore worth $12,000,000 from fissures in the Tintic quartzite along the Eureka Standard fault. Ores produced from the east Tintic mining district through 1971 are valued at $151.3 million. The production from the entire Tintic district is approximately $500 million. GEOLOGY The Burgin ore deposit occurs as replacement bodies in limestone, dolomite, and shale. Numerous fault struc¬tures and rock formations make the mine geology com¬plex. The mineralization is strongly associated with sev¬eral major geological features, which include the Ophir formation, consisting of limestone, dolomite, and shale as the favorable host rock, and the structural influence of the east Tintic thrust, the Eureka Standard and sev¬eral other significant faults. Fig. 1 depicts the Burgin 1300 level workings, a generalized configuration of the ore body, and the main geological features. Covering the quartzite, limestone, dolomite, and shale facies enclosing the Burgin ore deposit are 183 to 274 m (600 to 900 ft) of andesite. The Burgin ore consists of massive sulfide and oxide lead-zinc ores with significant silver and cadmium val¬ues. The main ore minerals are galena, cerrusite, and spalerite. Extensive manganese oxide deposits are associated with the lead-zinc ore occurrence. A limited

Jan 1, 1982

By Marcos de Paiva Bueno, Leonardo Ribeiro Lara, Rajiv Chandramohan, Thiago de Almeida, Greg Lane

This paper explores the impact of the significant difference between the number of geochemical assays conducted for grade estimation and the number of comminution tests performed for throughput and performance forecasting. Both grade and throughput are key factors in determining the project. We analysed 154 feasibility study reports to assess the impact of sample frequency for comminution test work on project revenue. This disparity in size between assay and comminution data arises because geological and resource-grade risks cannot be managed without extensive geochemical testing, whereas comminution risks are traditionally mitigated through design methods and the use of contingencies. This approach is partly due to the relatively high cost and large sample requirements associated with traditional comminution tests. Our analysis demonstrates that insufficient comminution sampling and testing leads to uncertainties in throughput forecasts, creating significant financial risks. Data from the feasibility studies show that a 1% change in mill throughput can result in up to a 5% variation in Net Present Value (NPV), underscoring the sensitivity of project economics to operational performance. Building on previous work, we reference studies that reveal how low frequency of comminution testing can increase uncertainty in mill throughput forecasts and increase financial risks. We propose an approach that optimises the number of comminution samples tested to enhance forecast accuracy and reduce NPV variance. By adopting this approach, mining projects can improve financial reliability and mitigate risks associated with underperformance in SAG and AG mill-based operations.

Feb 1, 2025

By S. R. Titley

Carbonate-hosted massive sulfide (60%) ores of the western Cordillera compose a distinct class of deposits although they vary widely in detail and perhaps genesis. They have been important sources of lead, zinc, copper, silver, gold, and more rarely, molybdenum, tin, and tungsten in complex mineral assemblages usually dominated by pyrite. They occur as concordant stratiform bodies, as discordant mantos, and as chimneys crossing tens of meters of section; many are associated with faults and breccia bodies. Environments of formation of carbonate hosts range from craton basin to shelf with ages from Proterozoic to Cretaceous; in many instances, dating has shown mineralization to be significantly younger than hosts. Temperatures of formation determined for many deposits are high (200°-400°) and many districts are centers of igneous activity manifested by dikes, sills, and stocks. However, direct cause and effect relationships have been difficult to establish. Many important problems attend the renewed interest and study of these deposits and include questions of metal-sulfur sources, metallization processes and histories, geological controls at all scales, and relationships to broader patterns of metallogeny.

Jan 1, 1985

By Evan Just

?We are certain there is need for research in every phase of mining." This statement by R. M. Crump of the Jones and Laughlin Steel Company (047) paraphrases opinion widespread among mining people. It is undoubtedly true. In preparation for this presentation, 193 organizations were asked to describe their mining research efforts. 60% responded, The meaning of "research" was taken in several different ways. The continual efforts of progressive companies to improve themselves were reported as research. We will call this and any effort to solve specific and immediate problems "practical research". The continuing investigation of subjects of long range interest will be called "basic research".

Jan 1, 1961

By J. M. Mutmansky

A number of previous publications have attempted to provide the practicing ventilation engineer with simple guidelines on the optimal velocity to be used in mine openings. Some of these velocities were meant to be used in metal mining operations and some were meant for coal mining. A careful review of these publications reveals that the optimal velocities were determined based upon assumptions that are not existent today. As a result, they are not suitable for use in a modern coal mine. This paper takes a new look at this problem and determines a statistical relationship for optimal velocity that can be applied under both current and future conditions. The analysis performed here is based upon the determination of the optimal velocity for coal mine entries under variations in power cost, mining cost differential, airway friction factor, time value of money, airway lifespan, and quantity of air carried. A total of 8400 different conditions were analyzed for optimal velocity using computer calculation of the capital and operating cost values. Using the individual values of the optimal velocity derived in the calculations, a linear regression equation was fitted to the data to relate the optimal velocity to the other six variables outlined above. This regression relationship allows the ventilation engineer to make an easy, rapid determination of the optimal velocity.

Jan 1, 1984

By I. B. Tulu, M. M. Sears

In 2015, 40 longwall mines provided nearly 60 percent of U.S. underground coal production. During this time, about 80 percent of ground-fall-related fatalities occurred in areas where the mine roof was supported. In an attempt to better understand the status quo of current longwall support practices in the United States, during a period between 2010 and 2017, researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) visited a sample of 25 longwall mines representing nearly 50 percent of the currently active longwall mines operating in all of the major U.S. longwall producing regions. The data presented here indicate that the types and amount of roof support being installed in modern U.S. longwall mines have reduced ground-fall accident and injury rates to levels never seen before. However, the complete elimination of unintended roof falls in U.S. longwall mines has remained elusive. The data in this paper can be used by mine operators and engineers to determine where their chosen type and density of roof support occur on the spectrum of observations contained in this database. Additionally, this data can be used to enhance, supplement and support additional research on longwall gateroad support systems. 

By A. L. Holmes

This presentation in the open pit session deals with the development of a phosphate rock strip mine by CF Industries, Inc., a company that does not presently mine in the Central Florida Phosphate District. Land acquisition, engineering, financing and environmental permitting activities were begun in early 1975; site preparation, environmental monitoring and dragline construction began in mid-1975. The operation is due on-stream in late 1978. The reserve acquisition, permitting, and financing could each easily be developed into a separate paper of interest. Each, however, has been covered before for other mining ventures with similar capital and environment requirements. For that reason, I have chosen to discuss what CF Industries, Inc. is, why it is entering this new sec-tor of the agricultural chemicals business, and, to keep at least some technical basis, what design modifications are possible when the total mine output is used captively and it is unnecessary to have the flexibility to meet the numerous transportation and customer specification considerations. In an attempt to show the size and complexity of the CF organization, a brief description of existing facilities should help show why the big interest in mining phosphate rock.

Jan 1, 1977

By Paul Wellman

The energy problem of the U. S; was emphasized by the oil embargo of late 1973 and early 1974 and it seemed for a time that the Federal Government, under pressure from the general public, might take some corrective action. However, this was not the case. With the gasoline lines gone and an apparent plentiful supply of petroleum products, public concern quickly dissipated., This country is more vulnerable to an oil embargo today than we were in 1973-1974 and this fact should be of concern to all our people. Since 1968, we have used oil and natural gas at a much more rapid rate than we have been able to find new domestic sources; thus, there is an increasing gap between domestic production and consumption and we have filled the gap with ever increasing oil' imports. These imports have increased at an alarming rate in the recent past, some 58 percent in 1976 compared with 1975. Imports are nearing 8 million barrels per day. Then, by applying some simple arithmetic, at $12 per barrel, the resulting trade deficit is $96 million per day or $35 billion per year. Obviously, this cannot be tolerated by our economy over a long period of time. Historically, we have shifted from one fuel to another as is shown in this slide. In 1850 about 90 percent of our fuel requirements came from direct combustion of wood, by 1900 we shifted to coal for 70 percent of our fuel, and now about 78 percent of fuel requirements comes from oil and natural gas. The difference is that the previous shifts were voluntary and the one facing us now is of necessity.

Jan 1, 1977

By JOHN R. HEBERGER, MAHIYAR F. NASARWANJI, Jonisha P. Pollard, Lydia M. Kocher

nt in the mining industry, and identifying factors associated with these injuries is critical for developing prevention efforts. This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011 to 2017. Hand and finger injuries occur at a rate of 6.53 per 1,000 full-time employees, which is nearly double the rate of the next highest affected body part, the back. Most of the hand and finger injuries were classified as cuts/lacerations/punctures (53 percent) followed by bone fractures/chips (26 percent). Materials handling and maintenance/repair were common activities at the time of the incident with miscellaneous metals — such as pipe, wire and guarding — and hand tools as the primary sources of hand and finger injury. Although the information on glove use was limited, leather gloves were most often worn when an injury occurred.

By Terry Owen

Business development process. Throughout Cyprus Amax's early months in Russia, the company stayed focused on what was needed from a deposit for economic success. Cyprus Amax's reason for success in Russia is that all involved - its Russian partners, the workforce and expatriates - provided a focused effort that served the project as it worked through the tender process and the Russian regulations. The company developed an understanding of the regulatory process by working with solid, ethical partners. Infused into the Kubaka management structure were Russians with the knowledge to facilitate the process and a professional group of expatriates. Developing credibility and a solid rapport with the Russian mining authority was critical to the success of this venture. Identifying and gaining the trust of key Russian individuals was also critical during the early stages. Gaining their trust and building credibility was part of the process. These key Russians were brought to the United States to visit existing Cyprus Amax mines. These efforts proved valuable in building an understanding with the Russians about the kind of company Cyprus Amax is and the kind of efficient operations that it can run. This was a learning process for all parties. Fortunately, the company was dealing with intelligent and educated people.

Jan 1, 1997