Search Documents

By Terence P. McNulty

Gold-bearing outcrops were discovered in 1862 by Union soldiers garrisoned at Needles, CA, near the northwest corner of the future State of Arizona. Sporadic mining began several years later, but engineered shaft sinking and mill construction were not adopted at Oatman and the neighboring camp of Goldroad until about 1900. Geological interpretations in 1915 enabled major production during the next decade. In the late-1930s, USSR&M built a new mine and mill in Gold Road and the District flourished until closure by Federal Order L-208 in October 1942. For about a decade, Oatman’s mines were among the largest gold producers in the American West.

Feb 1, 2024

By B. W. Stunkard

Hibbing Taconite Company is located by the cities of Hibbing and chisholm near the center of the Mesabi Range, approximately 169 km (105 miles) from the Canadian Border. The plant site is equidistant from these two communities, about 6.4 km (4 miles) from each. A 169 km (105 mile) railroad connects us with the port of Superior, Wisconsin, where the pellet production is loaded into lake carriers for lower lakes destinations. Immediately to the south of the mine area is the world famous Hull- Rust-Mahoning Mine which produced more than 700 000 000 million tons of red ore between the years 1893 and 1973.

Jan 1, 1979

By Arvid E. Anderson

The paper describes the unique operating features of the Lebanon Concentrator Plant wherein both magnetic concentration and froth flotation are used. Chalcopyrite is selectively floated by the use of dual collectors, Aerofloats and secondary butyl xanthate. Both potassium ethyl xanthate and sodium isopropyl xanthate (dual collectors) are dissolved and emulsified with pine oil for the flotation of the pyrite. Sketches describing the plant operations are presented and plant operating metallurgical results obtained are also given. The optimum production of minerals by the froth flotation process is normally achieved [ ] smooth operating conditions, The process, because of its many variables, becomes an art as well as a science. Therefore, any phase of the operation which will aid the operator in his control of the numerous variables will help produce a smoother operating plant, One of the most important variables which the operator deals with is the addition of reagents, These are usually costly items and should be used discretely with minimum amount of waste, The danger is that ,this emphasis may reduce the reagent amount to a point below that required, or, on the other hand an excessive amount is added, Both conditions usually yield poor results. The drea of the metallurgist is to provide the operator with the tools enabling him to produce a good mineralized froth at all times. Normally the operator has no control concerning the type of reagents which he must use. This has usually been worked out for him in the laboratory and by plant-scale tests. He does have limited authority to control the amounts of the reagents at his disposal. This, I believe, is as it should be. However, the operator should be provided with the best combination of reagents for his particular job. The providing of this combination of reagents for his particular job, The providing of this combination is often difficult, yet it is very important in order to yield good results, With this in mind, the dual collector idea was introduced for the selective flotation of chalcopyrite, and also later for the flotation of pyrite at the Concentrator Plant of the Bethlehem Cornwall Corporation in Lebanon, Pennsylvania, Supplying several types of collectors has given the operator an additional effective tool, even though great variations are encountered in ore tonnage treated and in ore composition, This paper deals with the use of the dual collectors and with the addition of the reagents in the form of a pine oil emulsion, or more accurately, a pine oil suspension. It is hoped that other operators may find the ideas helpful. There does not seem, to me, to be definite scientific fact which would substantiate the necessity for the use of dual collectors. However, in actual operations, the metallurgical results at Lebanon became more uniform with the use of dual collectors, I look upon it as an "insurance policy" which greatly aids the operator during those periods when he is having trouble, One theory has been advanced, i.e. one collector has a greater tendency to float the coarser minerals, whereas the other one may float the finer ones. Consequently, a combination of the two collectors will result in optimum recoveries, There has been some evidence that this is true, but it is not conclusive, on the other hand, the use of a xanthate-pine oil suspension (or emulsion) should speed up the surface reaction of the collector with the sulfide minerals, result¬ing in more uniform flotation, This has definitely happened in our particular case. A more interesting unexplainable observation has also occurred; i.e., the xanthate solution does not appear to lose its strength as rapidly when it is in the form of an emulsion (or suspension), This was first observed when a 50 gallon drum of a 20% ethyl xanthate solution was taken to Wilmington, Delaware, for a laboratory test, using a homogenizer to produce the xanthate-pine oil emulsion. Upon arrival, the drum of xanthate had developed a considerable internal pressure, The relief of this pressure was accompanied by a strong odor, When the emulsion was returned to Lebanon for the plant test orders were issued to release the pressure prior to emptying the emulsion. Nopressure had developed within the drum and there was no unusual odor present, Since this time it has been observed that xanthate pine oil suspensions have greatly decreased the possible decomposition of the xanthate solutions. In fact, suspensions have been exposed for more than a month without apparently effecting their reactions in the flotation plant. On the other hand, we found that the regularly mixed concentrated xanthate solutions, after standing for several days, did not give the same results as the freshly made ones. This effect was greatly reduced by the use of xanthate pine oil suspension (or emulsion)

Jan 1, 1958

By Sandip K. Mukherjee

This paper describes the application of pressure foam to control respirable dust in a double-drum longwall mining section. The feasibility of passing an adequate quantity of pressure foam through the shearer drum was initially established in the laboratory. Thereafter, underground testing of the foam system to determine its effectiveness on an active operating longwall was conducted in a mine in West Virginia. The foam system proved superior to the water spray system. The de- tails of the laboratory and field investigations, the results obtained, and the degree of acceptance of this system by the mining company are discussed in this paper.

Jan 1, 1984

By M. Ribeiro, P. So, P. Wong

Electrowinning is a process by which metals, such as copper or nickel, are recovered from aqueous electrolyte solutions resulting from the extraction of the metal ion from an acidic or basic leach solution. The electrolyte or “pregnant” solution is customarily forwarded to an electrowinning "tankhouse." In the tankhouse, the metal ions are deposited on cathode plates by electrodeposition and then recovered from the cathode plates. Other processes may be employed with other metals, such as nickel, zinc, among others, to produce an electrolyte from which their respective metals are obtained. During the electrowinning (electrodeposition) stage, elemental metal is plated out at the electrowinning cathode and oxygen evolves at an insoluble anode. The evolution of oxygen gas forms bubbles which entrain strong acid electrolyte, carrying it into the air above the electrowinning tank in the form of a fine mist or spray when the bubbles break. An acidic mist is generated above the electrolyte. This mist or spray then spreads throughout the electrowinning tankhouse. The acidic mist is corrosive and a health hazard and can cause extreme discomfort to the skin, eyes, and respiratory systems of tankhouse workers, especially during hot weather conditions. Polyfluoroalkyl based products (PFAS) have been widely applied as anti-misting agents in the electrowinning of metals in an acidic electrolyte. Functionalized PFAS compounds, however, have come under increased scrutiny by the EPA due to their impact on human health and the environment. There remains need for improved acid mist suppression agents for electrolysis and electrodeposition, particularly for products free of fluoroalkyl components.

Feb 1, 2023

By Steve Kral

In recent years, junior mining companies, mostly listed in Canada, have taken a beating in the finance markets. Simply put, potential investors have been leery of sinking millions into exploration and mining projects due to volatile commodities prices and an uncertain regulatory climate in developed and developing countries. The 2014 edition of the Prospectors and Developers Association of Canada (PDAC), however, seemed to be a bit different for some juniors. Equity valuations have improved and metals prices appear to be stabilizing. So, for some of the stronger junior companies, there is some hope. Merger and acquisition (M&A) activity is picking up and, believe it or not, companies are raising some capital. Billed as the largest annual mining meeting in North America, the PDAC conference attracted more than 25,000 mining and exploration professionals from around the world. Organizers were anticipating attendance to break the 30,000 mark. But, given the state of the exploration end of the mining business, 25,000 is still a respectable number. Junior companies that are in the project feasibility stage, or have made promising discoveries that stand a good chance of proceeding to production, are being looked at by potential investors. Those are the survivors of the last three years of dismal M&A activity. On the other side are the juniors that are still around ? and there are plenty of juniors that were at the PDAC last year but have since disappeared ? but have little or no working capital. One analyst calculated that there are about 850 companies with less than $200,000 in working capital and about 600 with negative working capital. This will likely result in fewer junior mining and exploration companies as the year progresses but the ones that remain should be stronger.

By William H. Eatock

The Saskatchewan ore zone strikes slightly south of East, from the Alberta border to Manitoba; and dips to the South. The conventional mines are located along a broad strike line from Saskatoon to Esterhazy-Rocanville. Nine conventional mines have developed ore bodies at a nominal depth of 915 metres (3000 ft.). One mine had developed an ore body at 1525 metres (5000 ft.) by solution mining. Mining reserves of 100 years are not unusual in this vast ore body. Most of the mines were brought on stream during the 1960s. All the conventional mines were influenced by practices developed at Carlsbad, N.M. By 1970, the industry was faced with serious over-capacity resulting in the cancellation of some projects and the introduction, by the provincial government, of the Potash Pro-rationing Regulations designed to share the available market amongst all the producers. This resulted in production rates as low as 40% of capacity. As a result, the 1970s were characterized by attempts to reduce cost, rather than improve production or processing techniques. In recent years, the plants have all been brought to full capacity, and are currently involved in a massive program of expansion, which promises a period of advancing technology.

Jan 1, 1980

By James J. Fallon

The industrial minerals industry is defined loosely and a specific list is presented. Criteria by which to judge prospects and examples are provided. General trends of the industry are observed.

Jan 1, 1984

By Jordi Vives-Costa, J. J. de Felipe, Lluís Sanmiquel, Maria Niubó

The article evaluates the convective heat transfer coefficient of ventilation air in a potash mine. The energy balance is obtained through thermal characterization of the ventilation air and rock, allowing for the calculation of heat transfer parameters. Different models for calculating the convective heat transfer coefficient are analyzed. The results indicate that the Pethukov–Kirilov, Gnielinski, and modified Dittus–Boelter models are optimal for this mine. The study also indirectly examines the conductivity of the adjacent rock, suggesting saturation throughout the studied section and the presence of liquid water upwelling in a specific section.

Apr 7, 2022

By C. Frenzel

Tunnel boring machines (TBM) utilize disc cutters as the primary means for excavating hard rock. Depending on rock excavatability and rock abrasivity disc cutters can exhibit significant wear. A detailed analysis has been carried out to characterize failure modes and wear patterns of disc cutters. The relationship between rock properties, op-eration of the TBM, and failure modes of cutting tools is clearly high-lighted. On that basis a prediction tool for disc cutter consumption has been developed that allows to estimate not only gross cutter life, but accounts for cutterhead design, premature cutter changes, and disc cutter repair costs.

Jan 1, 2011

By J. C. Wynn

J.R. Hillebrand From the abstract, "A realistic ore deposition model to serve as a conceptual framework." Further, on page 246, "The first area of study was the Josephine peridotite, now identified as an ophiolite terrane, located in northern California and south-western Oregon (Fig. 3). Here, it was felt that we could test the models shown in Figs. 1 and 2 and, if successful, expand the model and test it in other chromite districts in the US and around the world." My comments refer only to chromite deposits in Europe and the Middle East. First, I question that may chromite deposits occur in the idealized ophiolite section shown in Fig. 1. Second, although some podiform deposits (referring to morphology) have been important (Guleman, Turkey, for example), the stratiform deposits are of greater importance in tonnage and frequently grade. Examples include Nada, Yugoslavia; Bulqiza, Albania; Xerolivado, Greece; Saranovsk, Russia; and Abdasht, Iran. Reply by J.C. Wynn Mr. Hillebrand raises two issues that deserve a serious response. One issue is basically subjective and the other is ultimately political. First, the question of where (and how many) podiform chromite deposits are found in the idealized ophiolite section of Dickey (1975). The Dickey model is still perhaps somewhat controversial (Panayoutou, 1980), but our experience in the Josephine ophiolite of northern California (Wynn, 1980; and Albers, 1983) shows that the model works well there. Virtually all the chromite is found in dunite lenses in the tectonite peridotite (harzburgite). Since there are few complete ophiolites exposed in the world, the model will probably never satisfy everyone. The degree of acceptance is a function of any individual's subjective experience. Second, it is well known that stratiform chromite contributes more than 95% of the chromite reserves presently known in the world, and it could be reasonably argued that there is no point in exploring for or exploiting podiform deposits further. The title of the paper, however, was in part 'strategic minerals geophysical research'; chromite is considered a strategic and critical mineral of the US and many other industrialized nations. Stratiform deposits in South Africa and Zimbabwe account for most of the chromite reserves in the world. Unfortunately, experience in modern times with substantial price fluctuations and even resource cartels dictates the wisdom of identifying and maintaining a national chromite reserve, irrespective of the cost. An improved exploration methodology is an essential element in this strategic objective. References Albers, J.P., 1983, "Geological and Geophysical Studies of Chromite Deposits in the Josephine peridotite, California and Oregon," US Geological Survey Bulletin 1546 A-D, 118 pp. Dickey, J.S. Jr., 1975, "A Hypothesis of Origin for Podiform Chromite Deposits," Geochimica et Cosmochimica Acta, Vol. 39, pp. 1061.1074. Panayiotou, 1980, Proceedings, International Ophiolite Symposium, Cyprus, 1979, 781 pp. Wynn, J.C., 1980, "Exploration Geophysical Methods and Strategies, and Their use to Locate and Assess Small Mineral Deposits," Chapter 12 of Meyer and Carmen, eds., The Future of Small Scale Mining, McGraw-Hill, New York, pp. 75-83.

Jan 12, 1983

By Ahmet Tezcan, Zeki M. Dogan, Yalçin Kaytaz

Autogenous grinding in Turkey was first applied to quartzite where the mill is grate discharge type with an internal diameter of 2.99 m, having a length of 3.20 m and a capacity of as to 11.0 tons per hour. The second autogenous grinding was applied to a copper ore at Murgul Cakmakkaya Flotation plant of (KBI) Black Sea Copper Works having three mills 26 feet in diameter and 10 feet in length in close circuit with hydrocyclones. Recently, alterations were made in grinding circust by adding pebble mills. Furthermore, rubber liners and lifter bars were introduced pebble extractor and classifier were new features in the primary mills and circulating load was reduced by 20-50 tons per hour. At the end of these charges, capacity of each mill line was increased to 48 tons per hour with a full capacity of more than 9000 tons per day. Thirdly, autogenous grinding has been executed successfully on the slags of Samsun Smelting Plant of (KBI) Black Sea Copper Works with a mill of 20 feet in diameter and 6 feet on length having pebble mill following autogenous grinding.

Jan 1, 1992

By Kewal K. Kohli, Richard E. Thill, Syd S. Peng

The results of unpublished investigations into surface subsidence from coal mining in the Northern Appalachian Coalfield are summarized. These investigations were carried out by various coal companies and the State of Pennsylvania in the sixties and seventies. Subsidence data were collected and analyzed from 10 room-and-pillar panels in 5 mines in the Pittsburgh coal seam. Results show that angle of draw ranges from 26° to 33° and subsidence factor from 0.42 to 0.72; surface heating generally occurs beyond the edges of the panel, the amount and extent of which vary; waviness occurs in the subsidence profile if a substantial number of pillar stumps are left in irregular patterns; interpanel effect is significant; time-dependent subsidence exists, but varies for different panels; and surface slope does not seem to affect the amount of subsidence.

Jan 1, 1982

By W. W. Wen

A continuous pilot-scale test of the GranuFlow Process was conducted using a screen- bowl centrifuge for the dewatering and reconstitution of column flotation concentrate at a coal preparation plant in Virginia. In this test, a slipstream of the fine-clean-coal slurry from the column flotation concentrate was treated with a bitumen emulsion before dewatering. The treated products from the screen-bowl centrifuge appeared to be dry and in a free-flowing granular form, while the untreated products were wet, sticky, and difficult to handle. Specifically, test results indicated that the average moisture contents of the dewatered coal were 35.7, 35.5, 32.6, 29.9, and 26.5 wt% with Orimulsion additions of 0,0.7,3.2,4.8, and 6.4 wt%, respectively. The handleability and dust reduction of the dewatered coal product were also vastly improved.

Jan 1, 1997

Miners really are an optimistic bunch. Even with the dark clouds hanging over the global industry, mining professionals still turn out in droves at industry conferences. In February, more than 7,200 professionals attended SME?s Annual Meeting in Denver, CO, a record. And the following week, more than 30,000 people converged on Toronto, ON, Canada for the Prospectors and Developers Association of Canada (PDAC) meeting. For many small and junior mining and exploration companies the PDAC conference is a place to find potential investors in their projects. The Investors Exchange attracts several hundred companies, each showing off their properties to the many money types who wander the hall during the four-day conference.

Jan 1, 2013

By Ergin Arioglu, Werner Burger

"SUMMARY The Istanbul Strait Road Crossing Project includes a 3.34 kilometer subsea tunnel excavated by TBM with an excavation diameter of 13.71 m. The tunnel will incorporate two road decks, each employing two traffic lines and shoulder with the daily capacity of 100,000 light vehicles. The tunnel alignment crosses full face rock sections with heavily fractured zones due to tectonic events as well as a long central stretch of difficult mixed face and very variable soft ground conditions. The demanding ground conditions and the large diameter in combination with realized face pressures well above 10 bar required a highly specialized and well adapted TBM. The paper describes the project challenges and the related technical solutions incorporated within the TBM design as well as the real site experience. INTRODUCTION In 2013, a 13.71 m diameter Mixshield was manufactured in Germany for the Istanbul Strait Road Crossing Project. The delivery of the TBM in late 2013 was a major milestone for the Istanbul Strait Road Crossing Project, also known as the Eurasia Tunnel Project. The Eurasia Project (www.avrasyatuneli.com.tr/en) consists of a 14.6 km route including a 5.4 km tunnel segment in its central part crossing the Bosphorus. The 3.34 km subsea section of the tunnel was excavated in closed mode using a Mixshield TBM. The remaining tunnel length is constructed by sprayed concrete lining (SCL) method followed by a cast in place (CIP) lining or by cut and cover (CC) structures for the TBM transition boxes (Figure 1, right). Other project sections on the European and Asian side consist of upgrading and widening surface access roads towards the tunnel. Conceptual ideas of connecting Asia with Europe via a tunnel crossing the Bosphorus have been around for an extended time and only became realistic towards the end of the 20th century based on significant technical developments in mechanized tunneling. Feasibility studies for a new Bosphorus crossing in 2003 and 2005 confirmed and suggested a road tunnel in its present alignment as the preferred solution. Following an international tender process the Ministry of Transport, Maritime Affairs and Communications of Turkey assigned ATAS, a special purpose company formed by Yapi Merkezi (Turkey) and SK E&C (South Korea), to design, build and operate the Eurasia Tunnel Project. The Implementation Contract was signed in February 2011. In 2012, Herrenknecht AG was selected as the supplier for the 13.71 m Mixshield TBM."

Jan 1, 2016

By R. L. Kloberdanz

Peruvian legislation requires the preparation of an Environmental Impact Study (EIS) for new and expanding mines/beneficiation facilities and the preparation and implementation of an Environmental Adjustment and Management Program (PAMA) to control and mitigate environmental impacts associated with existing mining/beneficiation activities. Shepherd Miller, Inc., developed guidance documents for preparing an EIS and PAMA for Peru's Ministry of Energy and Mines and presented workshops to Peru's mining industry on preparing an EIS and PAMA. This paper discusses the process and approach taken and the results.

Jan 1, 1998

By Donald L. Everhart

The National Uranium Resource Evaluation (NURE) program since 1974 has been designed to accomplish a comprehensive coverage of the 48 conterminous States and Alaska to evaluate the total uranium resources of the USA. This resource base includes both ore reserves and potential resources. Techniques include airborne radiometric and magnetic surveys, by hydrogeochemical surveys, surface and subsurface geologic studies, and the application of improved geochemical exploration and resource assessment methods (Table 1). In brief review, the current status of each of the five basic NURE elements is as follows: In the Aerial Surveys, in the conterminous 48 states, the flying has been completed in 89 of the NTMS 10 x 2° NURE quadrangles, and is in progress in 39 more (Figure 1). Complete quadrangle data have already been open filed for 46 additional quadrangles, for a total of 174 for which data gathering is either complete or in progress. In Alaska, the flying is complete in 42 quadrangles, and quadrangle data have been open filed for 34 more, for a total of 76 (Figure 2).

Jan 1, 1979

By Richard L. Profio

A practical analysis of the three basic elements of a mining shovel's productive capacity. Payload Speed Reliability Improved dipper fill factor is explored referring to the latest generation of wide dippers combined with higher "bank horsepower" capabilities of modern drive systems. Cycle time improvement is reviewed including overall attachment geometry and coordination of motions. A specific case study is detailed. Basic reliability of welded structures, machinery components, and electrical systems are related to operating costs. Three basic elements determine a mining shovel's long term productive capacity: 1) Average payload per cycle. 2) Average cycle time; and 3) Reliability. This paper deals with productivity gains that are possible with existing shovels as well as new equipment.

Jan 1, 1984

By D. R. Nagaraj, Napoleon Tercero, Raymond Farinato

Historically, as for most reagents used in flotation, the wide-spread use of dialkyl dithiophosphinates as collectors in practical applications has preceded a detailed scientific understanding of how they work. Dialkyl dithiophosphinates are a technologically and commercially important class of collectors used in the flotation processing of Cu-Au, complex polymetallic, and precious metal ores. Plant usage has demonstrated that dithiophosphinates exhibit higher selectivity and flotation rates for Cu sulfides, galena, and precious metal values in the presence of other gangue sulfides, than the traditionally used collectors such as dialkyl dithiophosphates and xanthates. They also have an attractive health, safety, and environmental (HSE) profile. Although dithiophosphinates received little attention in the past in the flotation research community, recently, there has been significant interest in this chemistry, and numerous studies have been conducted to understand the fundamental interactions of dithiophosphinates with several base metal sulfides and precious metals. A critical overview of fundamental studies, laboratory ore flotation, and plant practice of dithiophosphinates is given in this paper. The findings from these studies are rationalized and explained by drawing on concepts and insights from coordination chemistry. A comparison between the interactions with various minerals and metals of dithiophosphinate and dithiophosphate analogues brings out some of the subtleties that seemingly minor changes in collector chemistry can make. The critical overview and analysis given here is useful in identifying gaps in knowledge regarding this important class of compounds. This in turn can provide a basis for the design of studies to advance our understanding of dithiophosphinate flotation performance.