Search Documents

By William R. Yernberg

The combined 79th Annual Minnesota Section of SME Meeting and 67th Annual University of Minnesota Mining Symposium was held April 11 and 12, 2006, in Duluth, MN. About 300 mining professionals attended, including engineers, executives, mining managers and suppliers, from throughout the United States and Canada. This year’s theme was “Success in the New World of Mining.” The SME Minnesota Section meeting included a keynote session, a special projects update, a general managers update and technical paper presentations. The University of Minnesota Mining Symposium program featured a panel discussion on Minnesota’s relationship with China. The combined meeting included a trade-show consisting of 64 booth spaces. Tradeshow demand exceeded expectations, and an additional 10 booth spaces were added in the registration lobby. Also included were an SME short course on pump basics and social events.

Jan 1, 2006

By M. E. Smith

Waste rock dumps, tailings impoundments and spent leach heaps are common features at mine sites. Many of these waste disposal facilities contain sulfide-rich minerals, which generate acid mine drainage (AMD) when they oxidize. Control of AMD can be achieved by removing one or more of the three essential components in the acid-generating process (sulfides, air, or water). One AMD prevention measure is to cap the waste with an engineered cover system to minimize the infiltration of water and diffusion of air into the system. Possible cover designs include: ? Earthen ?store-and-release? covers (also known as evapotranspiration (ET) or water balance covers), including capillary barriers. These covers require climate conditions where there is both modest to little rainfall and significantly greater evapotranspiration than precipitation, both annually and seasonally. ? Low-permeability compacted clay liners (CCLs) employing fine-grained soils typically compacted at wet of optimum water content. ? Geosynthetic composite covers, comprised of a geomembrane liner placed over and in direct contact with either a CCL or a geosynthetic clay liner (GCL). These systems have been commonly used for base liners for leach pads as well as covers and base liners at municipal solid waste (MSW) landfills in the US for more than 20 years. Comparisons of these different cover systems, both in terms of performance and cost, are presented later in this paper. First, however, a review of the typical mine closure approaches, and the possible rationale behind them, is warranted.

Feb 27, 2013

By W. J. Kennedy, John D. Gardner

Introduction During the past 10 years, energy costs in mining have risen from about 4% to as much as 25% of total production cost. When combined with declining ore grades, these costs exert inordinate stress on mine productivity. Industrial engineering techniques have traditionally been aimed at improving manufacturing facilities productivity, but they have been applied to mining as pressure for productivity improvement has increased. These techniques can perform four useful functions for mining operations by improving methods, equipment selection procedures, energy use through scheduling, and managing energy costs rather than being managed by them. This article discusses some of the standard techniques for productivity improvement, and how they can be adapted to perform these four functions. Pre-Production The best time to seek high productivity is when a mine is being planned. During pre-production, when most options are still open, an optimum mine design is achievable. At this time, major equipment selections are made, the layout, material handling systems, and processes are designed, and critical energy source decisions are made. By including explicit energy cost projections, decisions can be made that will save significant amounts of money per ton of ore over the life of the mine. Attention can also be given to often overlooked details such as lighting. Some of the same tools used in new mine planning are applicable to productivity improvements at an existing plant. These tools are the charting and modeling methods that have been developed by industrial engineers over the past 75 years. Energy Consumption Before any analysis of energy consumption can be performed, preliminary work is necessary to find the kind of energy used, how much it costs the plant, and when electrical peaks occur. Past bills should be examined to determine the monthly consumption rate and the cost of each energy type. These data should be adjusted to remove effects caused by production fluctuations or weather. Knowing when electrical peak demands occur is necessary because these determine either the electrical capacity needed or the amount that must be bought. At $500-$800 per kW for construction or $5-$15 per kW per month for purchase, they represent a significant cost. By the time these data are collected, planners should be aware of the importance of energy in the total cost of mine operation, and should have the most crucial time data for electrical peak demand. Flow Process Chart Reducing costs can be accomplished by a thorough look at mine systems and how altering one system causes changes in others. By developing and exercising models of production processes outward to the transportation of the final product, otherwise obscured weaknesses may become apparent. There are tools available for analyzing the mine and its associated systems; one of the most useful is the flow process chart. The flow process chart gives a system analysis of a production procedure by classifying all actions into one of five types: operations, inspections, transportation, delays without paperwork, and delays with paperwork. Operation: In an operation, the nature of something is changed. Examples are blasting, washing coal, and processing matter. Denoted by 0. Inspection: Examining an object for identification or to measure some attribute. Examples are determining whether a drill hole is deep enough, deciding how far to cut under an unsupported roof when operating a continuous miner, or checking the lubricant level on a truck. Denoted bye. Transportation: Moving an object from one place to another. Examples are transporting overburden, moving coal on a conveyor belt, and pumping water. Denoted by =>. Delay without paperwork: A delay that is an inherent part of the system. Examples include idle time of a continuous miner while waiting for shuttle cars or for roof bolting, crushed ore in a storage area waiting for grinding and flotation, and people from one craft waiting for another craft to finish. Denoted by D. Delay with paperwork: A delay that can be terminated only by some written authorization. Examples are coal that cannot be removed until authorized by a bill of sale and transportation orders, personnel records, maintenance, or spare parts. Denoted by V. In practice, the flow process chart is completed after data collection and a detailed examination of the process. Data collection is needed to answer questions on distance, quantity, and time for each of the operations. As the analysis is being performed, each step of the process is subjected to these questions: • Why is the step necessary? • What is being moved? • When does the step take place, and why?

Jan 11, 1983

By A. G. Sciulli, G. P. Ballock, K. K. Wu

Waste disposal underground is the most effective method when viewed from an environmental aspect. As costs of other methods of disposal continue to escalate, the cost effectiveness of underground disposal during the mining cycle becomes increasingly attractive. The use of concrete for sealing abandoned mines has proved to be suspect when associated with a relatively incompetent adjacent strata due to its shrinkage characteristics. Complete failure of the plug has been known to occur in some instances. A more effective, cost competitive seal can be obtained using pneumatically stowed material and incorporating a polyurethane grout, which has greater adhesion characteristics than concrete. Injection of the surrounding strata and of the stowed material helps to ensure an impervious barrier and prevent the plug from moving when subject to high pressure heads. When properly placed, impervious seals cause the old workings to flood, raise the mine pool level, and thus eventually eliminate the potential for oxidation, which is the primary cause of acidity in the water.

Jan 11, 1986

By Y. C. Kim, I. S. Roditis, P. K. Medhi

P. Mousset-Jones I found the article most interesting and timely. I consider it imperative that mine case studies like this one are undertaken and published so that the practicing mining engineer and geologist can obtain a better idea of what is the preferred estimation and grade control technique to use, given the site-specific geology, grade distribution, etc. Mining companies, with operating gold mines, need to be encouraged to either initiate such a study in-house or support a research project by financing a graduate student at a local university. The latter method is preferable since it not only provides research support but also an excellent training opportunity for young mining engineers and geologists. Ideally, what is needed is exploration drill-hole, blasthole, and mine production data that can then be used to assess the efficiency of different estimation and grade control methods by comparing the results obtained using the drill/blasthole data with the actual production data. It is hoped that more mining companies will realize that the rewards from this kind of research greatly outweigh the sometimes perceived problem with releasing data to a university. I noticed that the authors used the blasthole data to represent the actual values, the validity of which relies heavily on the two key assumptions with regards to blasthole assays and in-pit ore-waste selection procedures. Could the authors comment in more detail on these assumptions and what criteria they used to check the validity of the assumptions? Since the article was published, have the authors had the opportunity to compare their estimates with the actual production data? It would be interesting to compare other estimation methods with OK and IK. For example, how well did the polygonal method used at the mine compare with the results given in the paper? I would like to mention that B.L. Kwa completed a similar study (Kwa and Mousset-Jones, 1986) using exploration drill-hole, blasthole, and production data from the Alligator Ridge mine in Nevada. The study compared a variety of estimation methods, including IK, and the final results are shown in Fig. 1. The IK method exhibits the smallest difference between estimated and production results and is closely followed by the indicator moving window (Ind MW) method. Reference Kwa, B.L., and Mousset-Jones, P., 1986, "Indicator Kriging Applied to a Gold Deposit in Nevada," Proceedings, Symposium on Ore Reserve Estimation Methods, Models, and Reality, CIMM Annual Meeting, Montreal, Quebec, Canada, May, pp. 185194. Reply by Y.C. Kim We do concur with Professor Mousset-Jones with respect to the merit of such case studies performed at a local university. In answer to his request for comment on the validity of the two key assumptions made in our paper, we can only say that these are reasonable assumptions that are very difficult to validate. The assumption of blasthole assays being accurate can be partially validated by a careful analysis of the nugget component of blasthole variograms. The assumption that the in-pit ore-waste selection procedure in use was an effective one can only be validated through comparison between the mine estimates of ounces of gold versus the actual recovered ounces of gold at the mill. Neither one of these two assumptions has been validated to date due to several reasons. For example, the mine went through a change in management since the study. Similarly, no compelling reasons have been presented to perform detailed variogram analysis of the blasthole data. We do, however, believe that the obtained results (i.e., indicator kriging performs better than OK in a highly skewed deposit) will remain the same in relative terms, regardless of how valid these two assumptions may be. The most recent comparative study by D. S. Lindsey of the Montana College of Mineral Science and Technology also shows a similar ranking between ordinary kriging versus probability kriging, which is an extended version of indicator kriging. Reference Lindsey, D.S., 1987, "A Comparative Study: Probability Kriging vs. Ordinary Kriging at the Golden Sunlight Mine," MS Thesis, Department of Mining Engineering, Montana College of Mineral Science and Technology, Butte, MT, May, 81 pp.

Jan 3, 1988

By Leonel Lopez

Throughout Mexican history, mining has been an important, traditional activity. Before the "Discovery of America," native miners worked a variety of deposits throughout the country, including Mixtec gold and gem mines in Oaxaca State and Aztec gold, silver and copper from mines in Michoacán. The 500th anniversary of Mining in Mexico after the "Discovery of America" was initiated by the Mexican mining sector on April 15, 1991. As early as 1548, when the Guanajuato mining district was discovered, Mexico had become a leading world producer of precious metals. Since then, Mexican mineral production has developed in cycles, responding to changing technological, economic and political conditions. During the 20th century, Mexican mine output reached its peak in the decades of the 1930s and 1940s, when it was producing about 40% of the world's silver, 15% of its lead, 10% of its zinc, 4% of its copper and 3.5% of its gold. In 1990, by way of contrast, these percentages of world output stood at 13.5% for silver, 4.7% for lead, 4.1% for zinc, 3.2% for copper, and 0.43% for gold. The lowest production levels were recorded during the 1960s and 1970s, when Mexicanization of the industry and increasing state controls weakened mineral economics to a point that mineral exploration budgets were sharply reduced or eliminated, along with the industry's future. Only the noble old mining districts continued to supply production, with occasional eruptions of "bonanzas" and new extensions in established mining districts.

Jan 1, 1994

By D. F. Scott

The purpose of this study was to determine if miners are at risk from exposures to chemicals used in the mining industry, and determine the nature and sources of the illnesses and injuries. The authors reviewed the Mine Safety and Health Administration?s (MSHA) Employment and Accident, Injury, and Illness database and identified 2,705 cases of chemical-related injuries and illnesses that were reported to MSHA from 1999-2006, involving 66 different chemicals. The main source (cause) of chemical-related cases was acids/alkalis (about 39%). The primary nature (effect) of chemical-related cases was chemical burns (about 57%). The job classification where workers incurred the most chemical-related injuries and illnesses was cleaning plant operator/media operator/boney preparation plant operator/crusher worker. The number of nonfatal days lost did not change significantly and overall, the incidence rate of chemical-related cases decreased by 36%. Chemical burns accounted for a large number of injuries; mining companies should carefully examine their personal protective equipment (PPE) requirements, training methods, and safety culture to insure that their workers are protected.

Jan 1, 2009

By R. Mensah-Biney

The aqueous biphase separation process (ABS) has been used to separate ultrafine industrial minerals. The partition behavior ofTiO2, Al2O3, Fe2O3 and kaolin was not pH dependent. The partition behavior of SiO2 was, however, pH dependent. The partition coefficient of kaolin in PEG 3400/ Na2CO3 biphase system was 150 and that of the silica in the same system was 0.02, resulting in a separation factor of 8500 between kaolin and silica. The aqueous biphase separation system was used to separate free silica from kaolin in a raw clay sample from Mexico. The partition behavior of mica, feldspar and clay from North Carolina was also evaluated.

Jan 1, 1999

ME?s Arizona Conference was held at the Hilton El Conquistador resort in Tucson on Dec. 2 and 3, 2007. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together once each year to discuss the status of the industry. The 2007 meeting featured a keynote address, a distinguished lecturer and more than 25 technical papers that were presented in seven sessions. The sessions included environmental, geology, safety, metallurgy, mining, new projects and a special session on Mexico. Topics covered included mine closure, sustainable mining, exploration methods, health and safety issues, mining equipment and drilling. Much of the discussion at the conference concerned major new developments in the region?s copper mining industry. For example, Freeport-McMoRan?s new Safford Mine and BHP Billiton?s Pinto Valley restart were the topics of technical presentations. There was also much discussion among the attendees on the current and future price of copper, community relations, education issues and recruitment concerns. At the time of the conference, the price of copper hovered around $3.30/lb, up considerably from the 61 cents/lb in late 2001, when the industry was being challenged by world market conditions and a weakened domestic economy. Since then, strong demand from China helped push copper prices to record levels that at one time reached as high as $4/lb. The general consensus among the attendees is that the current price of around $3.30/lb will continue through 2008. Most attendees also expect increased corporate investments in the industry to continue. Copper mining in Arizona has been a major industry since the 1800s. In 2007, Arizona was the leading copper-producing state in the United States and produced more than $5 billion worth of copper. The copper mining industry in Arizona also produces byproduct gold, silver and molybdenum. Arizona is the second largest molybdenum producer in the United States.

Jan 1, 2008

By Harry Parker

Resource and Reserve Audits Becoming Increasingly Common Types of Audits -Review of Methodology (‘Fatal Flaw’) -Due Diligence – (‘Sign Off’) -Endorsement – (‘QA-QC’) Suggested Standards in Red

Jan 1, 2003

By G. E. Vaninetti

During its modem era, the southern Powder River Basin (PRB) in Wyoming has grown from meager origins in the early 1970s to become one of the most important coal-producing regions in the United States. In 1993, production and sales of southern Powder River Basin coal exceeded 190 Mt (209 million st), or about 20% of the US coal industry. Despite the remote location of the PRB relative to its potential markets, most coal industry observers anticipate continued strong growth to meet utility compliance plans for Phases I and II of the Clean Air Act Amendments (CAAA). This article is an overview of supply and demand issues concerning the marketing of southern PRB coal. It reviews the events leading up to the recent run on spot coal and offers a forecast of demand and prices.

Jan 1, 1994

By J. Darlington, A. K. SenGupta

Water-swellable layered silicates, namely, the smectite clays can remove suspended materials (called herein as debris) and metal ions from aqueous streams. The present study shows that the flocculating and metal extracting abilities of smectite clay-based flocculants can be enhanced when these clays are used in conjunction with a specific anionic polymer. Such performance enhancement is attributed to the following: i) the clay-dispersing ability of the polymeric additive, that would translate into an increase in the clay-surface area available for the attachment of the debris particles onto the clay particles; ii) the possibility of dispersant-to-coagulant transition of the polymer during the later instants of the treatment process, as a result of reduction in solvency of the wastewater for the polymer due to the release of cationic species from the clay-based flocculant solids; iii) metal-complexing ability and adsorption properties of the polymer.

Jan 1, 2002

By Joseph J. Diehl, Brian B. Khalighi

This paper discusses the Queens Water Tunnel, No. 3, Stage 2, being driven by a new Robbins High Performance (HP) Tunnel Boring Machine (TBM).The paper is divided into four sections. In the INTRODUCTION section, a short overview of the scope of the project is presented. In the GEOLOGY section, the geological condition along the tunnel drive is briefly introduced. The TBM DESIGN section discusses the various design criteria and the resulting machine specifications. The paper concludes, in the TBM OPERATION section, with a case history describing the tunneling operation from start-up to the time of the writing of this paper.

Jan 1, 1997

By R. Oler

The need for yieldable ground support, particularly in high stress or deep mining conditions, has grown in recent years. This paper highlights some of the current industry limitations and provides selection criteria for a new yielding ground support system, DSI?s Dynatork Bolt. This bolt distinguishes itself by withstanding 16 ? 30 kJ of energy deflecting loads anywhere from 7 ? 20 tons (depending on the energy). A summary of the laboratory test results and case studies will also be presented as a measure of the performance of this dynamic product.

Jan 1, 2012

By R. Oler

The mining industry?s traditional preference for protective coatings in corrosive environments, due to cost considerations, has been to apply galvanized and epoxy coatings. As a result of extreme pH levels and the limitations of current products, a new coating has been developed to withstand severe conditions. Harsh chemicals and corrosive groundwater pose added challenges to mines in maintaining long term ground support which demands continuous rehabilitation. This paper highlights the challenges and identifies a solution by applying a new economic coating to DSI?s Omega Bolt? that withstands the most corrosive of conditions. [ ]

Jan 1, 2012

Where space is limited, as it is throughout most of the northeastern United States, new construction either takes place high above street level, or below it. In Lower Manhattan, NY both kinds of expansion can be found in abundance. That is good news for the nearly 200 attendees at the George A. Fox Conference, presented by the Underground Construction Association (UCA) of SME at the Graduate Center, City University of New York, on Jan. 30. Among the many projects taking place in Lower Manhattan?s massive trans-formation process, are expansions to the city?s vast underground network of subways and other tunnels. ?New Yorkers either live on the ground or below it,? said keynote speaker Charles J. Maikish while explaining how an attempt to build above street level walkways never caught on in the city. Maikish is the executive director of the Lower Manhattan Construction Command Center. His job is to oversee the $22 billion project that will transform the island by 2010. From the construction of Freedom Tower at the site of the fallen World Trade Center buildings, to the expansion of the Second Avenue Subway, the extension of the East Side Access, No. 7 line, the new trans-Hudson line and numerous waterway tunnel expansions, including City Water Tunnel No. 3, the task Maikish is charged with is a huge one. He is primarily responsible for coordinating the scheduling and staging of the overall rebuilding plan, along with the day-to-day coordination of construction work down-town. He places particular focus on mitigating impacts on the environment and mobility, maintaining and improving access and alleviating congestion of any kind related to construction. At the time of the Fox Conference, there were 59 projects under way in Manhattan. All of those projects need things like concrete and steel delivered to sites in very tight working environments. And some need the equipment in even tighter spaces. ?This is not just about the recovery of Lower Manhat-tan (from the 2001 terrorist attacks) but this is a plan to restore it and to maintain its integrity,? said Maikish. ?I think that is the appropriate response to the terrorist attacks.? When Freedom Tower is completed, it will stand 541 m (1,776 ft) about the skyline. That will be a strong statement to the world about America?s strength. But it is the work that takes place much lower that was of interest to the conference attendees. On this respect, Maikish said Manhattan?s efforts below ground aim to provide relief to the city?s street level congestion and to make sure Manhattan ? already essential to the economy of the United States and the world ? stays current by upgrading the existing telecommunications and technological network while also allowing room for growth in that area.

Jan 1, 2007

By Gary B. Glass

Seventeen percent of US coal production now comes from the 19 surface coal mines in the Powder River Basin of northeastern Wyoming. The Powder River Coalfield, which coincides with this topographic and structural basin, is unique to the conterminous US, in that it contains an estimated 934.4 Gt (1.03 trillion st) of in-place coal resources. At least 13.2 Gt (14.6 billion st) is a compliant, strippable reserve base. In 1993, an estimated 162 Mt (179 million st), or 98% of the coal mined in this Wyoming coalfield, came from the thick - average 30.5 m (100 ft) - subbituminous, Wyodak coalbed, or from the Anderson and Canyon coals in the one mine where the Wyodak is split into two separate coalbeds. The other 2.7 Mt (3 million st) of coal mined in the Powder River Basin in 1993 came from the School, Badger, Monarch and Deitz No. 3 coalbeds. In this "world class" coalfield, there are at least 13 other persistent, 3 to 15 m (10 to 50 ft) thick, coalbeds as well as the Big George and Lake De Smet coalbeds, which are each 61 m (200 ft) or more thick in places. None of these latter 13 coals are mined at this time.

Jan 1, 1994

By Landy Stinnett

"When performing a valuation of a mineral property, a developing mine or perhaps an ongoing operation, the appraiser is typically provided with a range of information prepared by the property owner. This information can include ownership records, geological interpretation, assay data, an estimate of the reserves or resources believed to be on site (tons and grade), mine plans, production forecasts, capital and operating cost projections, and so forth.The appraiser familiarizes himself with the data, analyzes the various reports and then prepares the appraisal. There is usually a site visit, and there may be some effort at comparison of the particular mineral deposit with others in the region or with those of similar depositional characteristics, but for the most part, the appraiser is relying on the corporate documents, tempered by his/her experience in the field. Time is usually of the essence, the cost for the assignment has been trimmed, and therefore independent verification of the various components comprising the underlying data base (legal review, redrilling portions of the deposit, collection of new samples, re-assaying, etc.) is unlikely in most situations.In the case of high-value commodities — gold, silver, diamonds, perhaps the platinum-group elements — there have been numerous examples of the property owners attempting to increase the value of their holdings by nefarious methods. Most of these involve salting the deposit in some fashion; i.e., introducing small amounts of the commodity into samples being sent to a laboratory for analysis so that the resultant assay shows a higher grade (Donaldson, 2002; Greeley, 2001; Lechler et al., 2008 and Meech, 2001). Other schemes to enhance the apparent worth of a property include the use of nonstandard assay procedures, incorrect handling or withholding of the underlying information, and false reporting."

Sep 1, 2016

By K. Park, J. Sohn

Recovery of industrially useful metals from various secondary sources is an important issue in Korea whose natural resources are limited and needs in the strategic metals are on the rise. In order to meet such needs, researchers at the Korea Institute of Geoscience and Mineral Resources have launched a number of projects to help the nation to recover various metals from secondary sources. In this study, silver is successfully recovered from spent silver-oxide batteries first by distillation to remove mercury. The distilled residue was next subjected to leaching of silver using nitric acid. The study involves finding optimum conditions to leach silver from the distilled residue and subsequently to recover silver from the leach liquor by chemical precipitation. The chemically precipitated products are then subjected to reduction roasting to recover silver metal.

Jan 1, 2002

By M. Fan

Dry coal separation technology has particular advantages in the applications in arid and cold regions, or low rank coal separation. The hazardous pollutants in low rank coals can not be efficiently removed by conventional wet coal separation processes because a considerable amount of porose and easily friable low rank coals suffer serious particle size degradation problems in water. In this paper, a novel dry coal separation method with a vibrated air-fluidized bed of magnetic fly ash and magnetite is put forward for dry coal beneficiation. The magnetic fly ash used in this study was derived from fly ash obtained as a byproduct of coal combustion. The vibration?s effect on the uniformity and stability of a magnetic fly ash air-fluidized bed was studied. The 6×0.5 mm dry coal separation results with a vibrated air-fluidized bed of magnetic fly ash and magnetite showed that the probable error E value of separation is 0.06-0.08 t/m3.

Jan 1, 2009