Search Documents

S.L. Barua and Y.C. Kim M. Armstrong's paper is very interesting and can be regarded as a pioneering work of applying geostatistics on washed coal. The density levels used in her study are uniformly spaced, which facilitated curve fitting through a proper experimental design. Most of the existing coal washing plants in the US, however, gather washability data at non-uniform intervals which, in turn, affects the goodness of curve fitting. We would like to emphasize the importance of having a proper experimental design, if a similar geostatistical application is to be conducted on washed coal. We, at the University of Arizona, tried the variogram on recovery (Kim, Barua, and Baafi, 1982, SME preprint 82-143) which showed a similar pattern as Fig. 4 of Armstrong's paper. In both cases, the first experimental variogram value is invariably and inexplicably higher than the second variogram value. Although Armstrong ignores the first point because of "small number of sample points," we did not do so because there were 17 sample pairs. As a consequence, we concluded that the obtained experimental variogram was unsatisfactory and that further research is warranted. In other words, this disagreement in variogram interpretation between M. Armstrong and the University of Arizona begs the question whether the experimental variogram of Fig. 4 truly reflects the spatial correlation in washed coal, assuming there is such a correlation. Finally, we wish that Armstrong could have done a similar study on clean sulfur, which is a vital interest to the coal mines in the US. Her implied remark on sulfur in the concluding section of the paper may turn out to be incorrect because our experimental variograms on clean sulfur at different density levels were even less satisfactory than those on recovery.

Jan 1, 1985

By D. McBride

Representative samples are required from process streams in order to accurately measure chemical and physical characteristics. This information can then be used by process operators and metallurgists to evaluate the process and effect control actions for the operation. The capture and presentation of representative samples can be critical to measuring values, such as elemental analysis and particle size, with on-line or near-stream analyzers. A comprehensive multi-physics model has been developed and used to better understand the effects of slurry flow and particle segregation under certain operating parameters. An algebraic slip model coupled with a free surface algorithm is used to track motion and position of particles and phases within a specified geometry.

Jan 1, 2009

By J. M. Mutmansky

This paper outlines the results of a study of opinions of practicing engineers concerning the value of environmental engineering courses in a mining engineering curriculum. One hundred engineers with significant experience in mining-related engineering work were carefully chosen. Of the sixty-seven responses received, about half were from mining engineers and half from environmental engineers. The results of the survey are outlined in detail. The number and type of courses recommended by the respondents are summarized as well as the specific topics recommended for inclusion in a mining engineering curriculum. The survey form also asked for the stages in the mine life when environmental experts were needed and the percentage of environmental engineering performed by outside experts for many mining-related environmental tasks. The results of this line of questions are provided. Finally, the paper offers a comparison of the results for environmental engineers and mining engineers and analyzes the differences.

Jan 1, 2001

By T. L. Owen

Since 1993 Cyprus Amax has brought $2.5 billion dollars of greenfield and expansion projects into production, taking it from a mid-sized domestic minerals company into a major international minerals organization. The near simultaneous development of these multiple mineral projects in different locations around the world provided the opportunity for Cyprus Amax to develop a formal project management approach based, in large part, on an outsourcing philosophy. This formal project management system along with its outsourcing philosophy has served the growth agenda of Cyprus Amax extremely well. These preceding factors, coupled with the in-house retention of a core project group that fully understands the breadth of skills and abilities needed to undertake development of multiple large projects successfully, have been the cornerstone of Cyprus Amax’s project development success.

Jan 1, 2000

By Roger Best

In the mining industry, where some of the vehicles are larger than a one-story house, tire maintenance cannot be accomplished by the tire shop alone. It takes an army of people to maintain a fleet of 100 trucks that may be transporting gold, iron ore, oil sand, copper or coal from an openpit to a refinery and eventually delivering the product to a customer. Everyone working in and around these mammoth machines has a duty to help with the maintenance of the tires, whether they know it or not. These responsibilities comprise observation and reporting hazards up to and including changing out a tire and recording the information in a tire-tracking program such as TreadStat.

Jan 2, 2010

By F. E. du Plessis, P. De Waal

Through the development of innovative in-line mineral quantification sensors, the possibility has arisen to apply modern control theory to implement automatic process control for electrostatic high tension (“HT”) roll separators. A pilot-scale set-up was constructed to enable continuous tests to be carried out. A typical dry mill feed was continuously pre-heated and separated with a modern lab scale HT roll machine. The mineralogy as well as mass-flow of the non-conductor stream was quantified in-line, and the combined streams were re-circulated in an endless loop by a combination of vibration feeders and a bucket elevator. A fractional factorial experiment was executed to determine the most significant control parameters of the HT roll separator. Then a multi-input, multi-output dynamic model of the HT electrostatic separator was extracted by the application of standard system identification techniques for automatic control. The most important control variable to ensure a stable product grade could be identified. This allowed a robust single-input, single-output controller to be implemented. The process variable and set-point was mineral grade and the control variable was electrode voltage. Roll speed was manually adjusted while the mineral grade was kept on set-point by the control system. The roll speed, where maximum mass flow and therefore maximum yield was produced on-grade, could therefore be rapidly determined. Atmosphere humidity and ore temperature served as disturbances. Some other adjustable parameters were kept constant during the experiments, namely feed mineralogy, splitter settings and feed rate. Delivery of maximum yield, with a controlled grade, can improve production while reducing the burden of complex manual tuning. Manual tuning previously involved coping with multiple parameters with uncertain cross coupling influences on the end result. Even the end result was typically only known after completion of mineral assays. Automatic grade stabilisation and yield optimisation for a HT roll separator bank requires in-line measurement of mineralogy and mass flow, as well as the implementation of a robust process control system.

Jan 1, 2005

Ten years ago, only 3% of Consol's underground coal production resulted from using the longwall mining method. Today, that figure has grown to 45% and has helped the Pittsburgh-based concern fuel an upswing in productivity. The company reported that productivity at its underground mines, excluding labor strike periods, increased 24% between 1978 and 1981. Last year, an additional 8% increase was achieved. Efforts such as improved safety, training, engineering, and maintenance programs as well as the closing of unproductive mines has contributed to these gains, according to Joseph M. Richards, Consol's executive vice president of operations. But, Richards adds, a great part of the credit goes to longwall mining. What is Longwall Mining? To fully appreciate the advantages of longwall, one needs an understanding of how mining is done by other methods. For instance, in both conventional and continuous mining, rooms or tunnels are dug in the coal seam. Pillars of coal are left standing to support the roof as mining moves forward in the seam. In conventional mining, a slot is cut in the base of the seam and holes for blasting are drilled. After blasting, the coal is loaded. A more efficient method - continuous mining - uses a machine that combines cutting and loading. Longwall mining, by contrast, works backwards from the end of a panel. Two parallel sets of tunnels (development panels) are cut into a seam with continuous mining machines, then connected with a set of crosscuts at the far end. Min¬ing then proceeds back toward the entrance. Longwall mining employs some very productive machines. Large drum shearers, for example, run on a track along the length of the coal face for some 150-180 m (500-600 ft). The shearers cut the coal which falls onto a conveyor system or pan that also runs the entire length of the face. The longwall crew works under a roof of heavy steel supports called shields. As the coal is removed, shearers, pans, and shields are moved forward by hydraulic rams. The roof is allowed to collapse behind the shields. In addition to increasing production, longwall mining is considered to be safer because the miners work under strong steel shields. New designs have made them more rugged and maintenance free, as well as more stable on soft mine floors. Early roof supports, called chocks, had gaps in the roof canopies. The new roof shields now cover the entire working area and are better able to prevent roof material from falling into the working area, thereby improving safety and productivity. Longwall mining also results in a cleaner product in many mines. If the first layer of rock over the coal seam is thin, it might have to be removed with the coal in a room-and-pillar operation so a

Jan 11, 1983

By Reed Thorne

To many people, rescue from elevated, sometimes vertical, locations brings about thoughts of heroism mixed with brawn and self-sacrifice. Images are conjured of cliff rescues where the technical effort is hanging from a few seemingly small nylon ropes hundreds of feet above the ground. Such is the vertical realm of technical rope rescue. This is a technical field in which the author serves professionally as battalion chief of (rope) operations for a northern Arizona fire district, and as a private sector instructor to mines in the United States and Canada.

Jan 1, 1996

By W. G. Pariseau

Introduction Caverns of 50 m in linear dimension at depths below 2300 m with a life of more than 25 years are proposed for the next generation of water-filled neutrino detectors. Little precedent exists for excavations in such an extreme environment, although some guidance is available from mining experience at great depths, for example, in South Africa, in Canada and at the former Homestake Mine in the U.S.A. Unlike mining for ore, there are choices available in the construction of such caverns that may mean the difference between success and failure. These choices should be informed by rock engineering principles. Recently proposed guidelines for orientation of brick-shaped caverns where the long dimension is a small multiple of the short dimension indicate that the most favorable orientation is with the long and short dimensions parallel to major and minor preexcavation principal stresses (Pariseau, 2005). Numerical analyses at reduced strength indicate some yielding at cavern walls should be expected but that an equilibrium state is quite possible and is aided by arching the back into a spherical dome when the cavern is an empty cylinder (Tesarik and others, 2002). The same indications of stability occur with brick-shaped caverns. However, the most dangerous situation occurs during the excavation sequence to final cavern dimensions. There are any number of excavation sequences that lead to the same final cavern shape, so there is an opportunity to partially optimize the sequence with construction guidelines that minimize peak stress concentrations during construction. This contribution discusses three practical excavation sequences that lead to the same brick-shaped cavern in the strong, massive Yates formation at the Homestake Mine where considerable rock mechanics data has accumulated through the years(e.g., Pariseau, 1985, Pariseau and others, 1995) and where actual mining on the 8000 Level indicates a strong possibility of successful investment in the next generation of large, deep neutrino detectors. The main results are: (1) a favorable brick-shape is one with dimensions in the same proportion as the preexcavation principal stresses (compressionpositive), and (2) favorable orientation of the most extreme but temporary shape of excavation is also best for the construction sequence. Analysis results from a mix of Homestake Mine data and possible excavation geometry illustrate the advantages of these guidelines.

Jan 1, 2006

By Micheal Mitariten

The recovery of natural gas (primarily methane) from coalbed deposits is an established and growing source for the U.S and accounts for over 7% of its total production. The gas from on-purpose degassing is often pipeline quality and requires only compression and dehydration before being admitted to the pipeline grid. However, the raw gas is sometimes contaminated with nitrogen (N2) and/or carbon dioxide (CO2) that can make the gas inadmissible to the transportation pipeline. In general, the N2 must be 4% or less and the CO2 should be 2% or less. In treating gas produced from virgin coal bed or from degassing operations where CO2 is present, amine systems are traditionally used for its removal. Engelhard’s Molecular Gate® adsorption system offers an attractive alternative due to its skid-mounted equipment, low pressure and unattended operation, cost and high on-stream reliability. Natural gas can also be sourced from the residual coal, after the coal has been mined. This source can be the GOB or gas remaining in abandoned coal mines. This source is almost universally contaminated, often with a combination of CO2 and N2. If the source is from air intrusion, the source can also be contaminated with O2. In treating CO2 / N2 contaminated feeds, the Molecular Gate adsorption system removes both of the impurities along with a level of O2 within a single processing step. To date, ten Molecular Gate units are underway with three systems having been installed for upgrading gas from abandoned coal mines. The technology consists of specialty adsorbents and advanced PSA processes that are jointly offered as fabricated packaged equipment by Engelhard Corporation and Guild Associates, Inc. Upgrading requirements, project challenges and project arrangements are discussed in this paper.

Jan 1, 2005

By Syd S. Peng, C. Y. Chen

Introduction The Surface Mining Control and Reclamation Act was passed in 1977 to put an end to the uneven environmental standards and enforcement established by various coal mining states in the US. One year after passage, the Secretary of Interior was directed to promulgate permanent program regulations implementing Title V provisions of the Act. These regulations were to form the basis for state regulatory programs under the Act and to allow states to assume primary regulatory responsibility. To implement the underground mining provision of the Act, the Secretary is directed in section 516(a) of the Act to promulgate rules. But they must take into consideration the differences between surface and underground coal mining. The regulations developed by the Secretary in 1979, with respect to subsidence control, included: • a subsidence control plan as part of the permitting process; • substantive provisions establishing performance standards for subsidence control; and • provisions providing for the prohibition of mining under perennial streams, impoundments larger than 24.6 dam3 (20 acre ft), and certain public facilities and urban areas. Industry challenged the Secretary's regulations implementing the subsidence control provisions. The litigation was consolidated with all other challenges to the permanent program regulations. (Permanent Surface Mining Regulation Litigation, Civil Action No. 79-1144; D. D.C., May 16, 1980.) In two opinions dealing with the multitude of issues raised by both industry and environmental groups, the US District Court of the District of Columbia ruled against industry. It upheld the promulgated subsidence control provisions. The US Court of Appeals stayed the appeals pending the agency's review and revision of its regulations. The regulatory reform was conducted in accordance with the order from the Secretary of Interior and the President in 1981. As a result, the subsidence control regulation was revised, reproposed, and finalized in June 1983 (Federal Register). This regulation, along with others, was again challenged by environmental groups and industry. On Oct. 1, 1984, the court, after finding the Secretary's reading of the Act reasonable, upheld the 1983 subsidence regulation except for one section. On Feb. 21, 1985, in accordance with the court's ruling, the Office of Surface Mining (OSM) suspended a portion of 30 CFR 817.121 (c)(2) concerning the damage correction requirement for structures or facilities and reproposed it on July 8, 1985 (Federal Register). In conjunction with a request for public comments, OSM now also seeks comments on the omission from the 1983 rule of the requirement in the 1979 rule regarding a presubsidence survey and monitoring of damage to structures. Technical issues related to subsidence regulations The subsidence regulations of June 1, 1983, consist mainly of two parts: a subsidence control plan as part of the permitting process; and substantive provisions establishing performance standards. The latter also includes provisions for prohibiting mining under certain areas. Under subsidence control plan section 784.20, minimum require-

Jan 2, 1986

By L. Mukka

The existing main mine ventilation system for the production areas to the Kiruna mine was constructed during the period 1994-1996 and extended with 4 more shafts, including fan stations, for the sea ore body from 1997-1998. Two papers have been presented from this project at the 7th US Mine Ventilation Symposium in 1995 and at The 6th International Mine Ventilation Congress in 1997. In 2005, pre-studies for a new main haulage level were started. Different haulage methods were presented including ventilation systems. The pre-studies showed that the existing ventilation system, including fan stations for the new main haulage system in the production area, could be extended. However, a new system for the central area, which was not in the initial investment program, would be needed. In the beginning of 2006, a decision was made to design a new ventilation system for the central area to make it possible to get air to the development work for the new main haulage system, independent of the haulage method. This system was operational by the beginning of 2007. The new main haulage system, which was decided to be located on level 1365 m, only requires that the existing shafts be extended - the capacity of the fans seems to be enough. However, the problem is that the existing level 1045 m and the new level 1365 m have to be in operation in parallel for approximately 7-8 years. The challenge for the moment is determining how to ventilate the production areas for both levels at the same time, while simultaneously constructing the extended system. This paper will describe the problems associated with the extension of the main ventilation system and some potential solutions for these problems. The new main haulage level 1365 m must be in operation by 2012.

Jan 1, 2009

By K. R. Griffin

Explosions in underground coal mines have been a serious safety concern since the advent of mining; despite significant technological advances, they are still occurring. Parameters such as barometric pressure, geological changes, and changes in ventilation can contribute to an explosion. These factors can be monitored with available and developing technologies to create algorithms that predict when explosions are more likely to occur. This paper reviews current underground atmospheric monitoring systems and related regulations around the world. In addition, suggestions for improvement and implications for explosion prevention are discussed.

Jan 1, 2011

By M. L. Harris

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) has developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five and three underground coal mines in MSHA District 2 (PA) and District 11 (AL), respectively. While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (% IC) determined by the CDEM agreed well with those obtained later by low temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

Jan 1, 2008

By John F. Beesley

INTRODUCTION This paper discusses the design of the subsurface nuclear waste repository at Yucca Mountain, Nevada; and possible concepts for construction of the subsurface facility. Subsurface construction at Yucca Mountain is planned to last for 20 or more years, and may be accomplished using tunnel boring machines (TBM), drill and blast methods, raise bore machines, and roadheaders. The design of the subsurface facility includes approximately 107 km (66 miles) of tunnels and drifts. The vast majority of the repository will be excavated with TBMs. Design and construction concepts for the subsurface repository discussed in this paper are based on the License Application that was submitted to the U.S. Nuclear Regulatory Commission (NRC) by the U.S. Department of Energy (DOE) on June 3, 2008. The License Application was subsequently docketed by the NRC in September 2008. When a Construction Authorization is received from the NRC, notices to proceed with subsurface construction at Yucca Mountain will be issued by DOE. The Yucca Mountain site is located in the Mojave Desert approximately 150 km (90 miles) northwest of Las Vegas, Nevada. The site is on federal land in southern Nevada and is shown in Figure 1. Yucca Mountain is a ridge of volcanic rocks com-posed primarily of solidified volcanic ash. Previous underground construction work at Yucca Mountain included excavation of two tunnels using two different TBMs. The first tunnel, the Exploratory Studies Facility (ESF), is a 7.62 m (25 ft) diameter tunnel that is 7,877 m (25,843 ft) long and was described by Morris and Hansmire at the Rapid Excavation and Tunneling Conference (RETC) in 1995. The second tunnel, known as the Enhanced Characterization of the Repository Block (ECRB), was a TBM drive of 5.0 m (16 ft, 5 in.) in diameter and 2,681 m (8,796 ft) long. The second tunnel was excavated in 1998 and was described by Fulcher, Eastlund and Copeland at RETC 1999 and is named the East?West Cross Drift in that paper. (These previously excavated tunnels are shown in Figure 2.) In the volcanic rock formation where the vast majority of the planned repository will be con-structed, previous tunneling conditions were generally very good.

By E. Farrokh

Estimation of the cutter life and cost is a part of evaluating performance for a hard rock TBM in any project. Various approaches has been proposed for calculation of disc cutter life in various rock types based on machine specifications and rock strength and abrasivity. Cutter change time is a parameter that is used in some of the estimates and is defined as the average time required for changing a cutter on the cutter head and cutter life is the number of cubic meters of excavated rock per each disc cutter. Analysis of cutter life information of several tunnel projects from around the world has revealed that the published models for estimation of cutter consumption require some revisions to offer a more accurate prediction. The preliminary analysis of data shows that the average cutter change time is approximately 66 minutes for different cutter sizes and there is a minimal difference between corresponding cutter change times of the large (e.g. 19 or 20 in) versus smaller cutters (e.g. 15.5 to 17 in). This paper reviews the available and published cutter life data from various projects. It also introduces new models for estimation of cutter life and cutter change time as part of TBM down time and utilization analysis.

Feb 27, 2013

Basic parameters affecting the stability of foams have been studied. We used the thin film pressure balance (TFPB) technique of Scheludko and Exerowa (1959) to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, MIBC, and PPG. The results were compared with the froth stabilities measured using the shake tests and the film elasticity calculated using the model developed by Wang and Yoon (2006). It was found that the froth stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother concentration and type.

Jan 1, 2006

By William R. Yernberg

The Fifth International Heavy Minerals Conference (HMC) was held Oct. 16-19, 2005, at the Marriott Sawgrass Resort in Ponte Vedra, FL. With SME as sponsor, the 2005 conference marked the first time that the HMC was held in North America. The conference is held every two years and provides an important forum for professionals in the heavy minerals and related industries to meet and discuss issues related to heavy mineral exploration, mining, processing and marketing. Previous locations included Australia and South Africa. The conference consisted of technical presentations, field trips to heavy mineral operations, a trade show and social activities. It was appropriate that Ponte Vedra was selected as the location for the conference. Ponte Vedra, located on the Atlantic Coast 17 km (10 miles) southeast of Jacksonville, FL, is the birthplace of heavy minerals mining in North America. Ponte Vedra beaches were mined from 1916 to 1929 in what was then called Mineral City. Though Ponte Vedra is now a golf and beach resort, there are still four heavy mineral mines operating within an hour’s drive. Today the Ponte Vedra Country Club and Golf Course is situated in the center of the former mining site.

Jan 1, 2006

By S. Underwood

The tracer gas method of conducting ventilation surveys is a means of determining air quantity in underground mines with knowledge of the concentration of the tracer in the atmosphere and the flow rate at which the tracer is being released. The technique is useful in inaccessible areas of underground mines and areas where traditional point measurement of velocity is not practical. Sulfur hexafluoride (SF6) is the industry standard tracer(Kennedy 1987) used in underground mines because it is safe, stable, and not naturally occurring in the mine environment. The implementation of a second tracer will increase the versatility of the tracer gas technique allowing for simultaneous releases for the study of interrelated ventilation circuits, and for conducting multiple experiments in less time. This paper will detail the selection of perfluoromethylcyclohexane (PMCH) as a novel tracer with sensitivity, physical properties, and analysis characteristics similar to SF6. Methods for the release of liquid PMCH into underground mines will be recommended, and the vulnerabilities of sample loss due to condensation of vapor PMCH will be explored. Finally, the benefits and implications of using PMCH as a second tracer will be discussed.

Jan 1, 2012

By T. M. Barczak

Stoppings are required to resist lateral forces on the face of the structure to control pressure differentials created by ventilating air. The design criteria in other parts of the world, including Australia, exceed this requirement by specifying over pressurization control to as much as 14 kPa (2 psi) in the active sections and 35 kPa (5 psi) in the main ventilating control areas. This is done to provide protection to the mine workers from explosive or air blast events within the mine that can create this over pressurization. The National Institute for Occupational Safety and Health (NIOSH) has been conducting research to develop a new testing protocol for rating mine ventilation stoppings. The premise of this work is that arch-loading conditions more accurately reflects the transverse load capabilities of stoppings in underground coal mines than the freestanding flexural strength test specified in the current Code of Federal Regulations (CFR). This work clearly shows that the transverse load capabilities of dry-stacked, mine ventilation stoppings are dependent upon the material strength of the block and the height and thickness of the wall, none of which are part of the current CFR criteria based on ASTM E-72 specifications. This paper compares the transverse load capabilities of several block materials and wall dimensions commonly used in stopping constructions based upon simulated three-hinge, rigid-arch loading tests of half-wall constructions in the NIOSH Mine Roof Simulator. The results indicate a wide-range of transverse load capacities, ranging from as low as 21 kPa (0.3 psi) to as much as 117 kPa (17 psi) for the conditions evaluated in this study. The current CFR criteria do not distinguish between applications of these stopping designs despite their wide variance in transverse load capabilities, which is not conducive to employing ventilation control strategies that isolate certain sections of the mine to prevent injury to mine workers.

Jan 1, 2009