Search Documents

By K. N. Han, Y. Guan

[The dissolution behavior of copper and gold from their pure state and from Au-Cu alloys in cyanide solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of the alloy composition, stirring speed of the disc. [lixiviant] concentration, solution pH and temperature on the overall dissolution kinetics has been studied. An-Cu alloys of three compositions were used in this study. The atomic percent of gold in these alloys was 75, 50 and25, respectively. The dissolution behavior of these three alloys was compared, under the same chemical conditions, with that of pure gold and pure copper. In general, the dissolution of copper and old from alloys is controlled partially by surface chemical reaction and largely mass transfer.]

Jan 1, 1994

By P. N. Psarropoulos

During many strong earthquakes in the past, a significant number of tailings dams failures has been recorded, leading in some cases to human life losses. However, over the last decades, seismic design of tailings dams has drawn much attention mainly due to the high environmental hazard. Although the stability of such geostructures under dynamic loading is mainly related to their liquefaction potential, there exist several technical issues that have not been adequately investigated. One of these issues is the impact of local site conditions on the dynamic earthquake stresses developed, and therefore on the inertial instability of these dams. Based on the models examined in the first part of the present study (Stability of Tailings Dams ? Part I: Static Loading), two-dimensional numerical simulations are performed in order to examine the effects of local site conditions in the dynamic response of tailings dams. Imposing dynamic loading via characteristic pulses and real earthquake records, the most commonly used types of construction methods are studied at their final stage. Emphasis is given on the special characteristics of the ground motion, while the material nonlinearity of both soil and tailings is taken into account by an equivalent-linear procedure. The results obtained indicate that local site conditions may have a significant impact on the seismic response of a tailings dam.

Jan 1, 2005

By Sukumar Bandopadhyay

In recent years planning of surface mines in general and reclamation and post-mining land uses in particular have become very complex. Due to the lack of suitable techniques, land use plans are rarely based upon structured decisions. Data collection may be conducted in a rigorous manner and certain analyses may be performed on the data; the decision to put the land to a specific use, however, is finally based upon the intuitive judgment of one or several individuals. This paper demonstrates how techniques from fuzzy set theory can be used in order to select an optimum post-mining land use plan. The various land use planning alternatives have been characterized according to both qualitative information and quantitative factors and the "fuzzy" aspects of the collected information are incorporated into the analyses. In a practical application, the methodology is used to obtain the most reasonable solution to a post-mining land use planning problem in Interior Alaska.

Jan 1, 1986

By A. K. Bakshi, K. J. Shoop, Komar S. Kawatra, T. C. Eisele

Slurry rheology can have significant impact on the performance of autogenous grinding circuits. A viscous slurry can act as a cushion and retard impact forces between the media and the ore, which reduces grinding efficiency. On the other hand, a dilute slurry will not be viscous enough to hold slurry in the impact zone of the media, which will lead to inefficient use of impact energy. An unfavorable rheology can also lead to overgrinding or centrifuging of the slurry inside the mill. Slurry rheology also affect classification, with higher viscosity increasing the cut size. In this article, the causes of the rheological effects on autogenous grinding and hydrocyclone classification have been discussed. Both plant and pilot scale data from autogenous grinding have been provided to show the effects of viscosity on specific energy con- sumption and other breakage characteristics of the ore. It is shown that: (1) high viscosity, produced by low temperature and high fines content, significantly increases the specific energy consumption and the production of critical size material in an autogenous mill; (2) In hydrocyclone operation, increasing the viscosity causes the d50(c) size to become coarser.

Jan 1, 1998

By John F. Shea

When tunnel boring machines were first developed, the J. F. Shea Company elected not to use them until some of the bugs were worked out. When we did take the plunge, we learned a great many lessons in tunneling; amongst others, that tunneling with a TBM is more an art than a science. One of the most important factors that contributes to a successful TBM tunnel is the geology. A machine can be designed to handle almost any type of ground; however, if the ground is not uniform, compromises in design must be made to enable the machine to handle the various ground conditions. Even when the geologic formations are well defined, it is still impossible to predict how the formations will react when it is penetrated by a tunnel. This is where the design and performance of a tunnel boring machine runs into trouble. When the reactions are adverse, the contractor is left with three alternatives; park or pull the machine and drive conventional, fight through the formation with no changes, or modify the machine. We have made all three of these choices. The first, on the Tonner Tunnel in Southern California, we encountered an extremely tough sandstone where progress was measured in inches per day. Ultimately, we pulled the machine and drove conventional tunnel. The second, on the Vat Tunnel in Central Utah, another element was added to the geology - water, which we encountered in excess of 1,000 gpm at the heading. It was impossible to adapt the machine to handle this much water, so we have been carrying out a program of grouting ahead of the machine and then driving tunnel with the tunnel boring machine.

Jan 1, 1981

By Greg Adel, Darren Thornton, Julius Krutschnitt, Toni Kojovic, J. Mark Richardson, Bryan Smith

Mine-to-Mill® optimization is a total systems approach to the reduction of energy and cost in mining and mineral processing operations. Developed at the Julius Krutschnitt Mineral Research Centre in Queensland, Australia, it attempts to minimize energy consumption through the optimization of all steps in the size reduction process. The approach involves sampling and modeling of blasting and processing, followed by computer simulation to optimize the operation and develop alternatives. The most promising alternatives are implemented, and sampling is conducted to quantify energy savings. In the current DOE-sponsored research project, the primary objective is to adapt the Mine-to-Mill® technology to the aggregates industry. The project is being carried out at two quarries operated by Luck Stone of Richmond, Virginia. This paper presents work conducted at the Bealeton quarry.

Jan 1, 2005

By Steve Kral

Philip M. Hocker is president of the Mineral Policy Center (MPC), a Washington, DC-based, non-profit organization formed to "address the environmental problems that are caused by mineral development in both the hard-rock mining and onshore oil arenas." Hocker has been involved with resource development and environmental policy issues since the 1970s. He has been a plaintiff in several lawsuits regarding environmental management of federal onshore oil and gas leasing. He was also active in the 1987 campaign to pass the Federal Onshore Oil and Gas Leasing Reform Act. Hocker served on the board of directors of the Sierra Club from 1980 through 1986. He is also a member of SME and spoke at the welcoming luncheon and keynote session of the SME Annual Meeting and Exhibit, Feb. 14, 1994, in Albuquerque, NM. In his role as president of MPC, Hocker has become a major player in the ongoing battle concerning mining law reform. And, while the mining law issue is the most visible and controversial issue confronting the mining industry and MPC, Hocker's organization is also active in clean water reform and other public policy issues that concern natural resource development and the environment. Hocker and MPC invoke a wide spectrum of reactions from the mining industry, most of it negative. Even so, the editors of ME decided that SME members should hear from Hocker his views on domestic mining, including mining law reform, clean water legislation and other environmental issues facing the industry.

Jan 1, 1995

By Y. Topkaya, R. E. Johnson, B. R. Palmer, R. B. Bhappu, J. Brent Hiskey, Gürses Öner

Currently there is considerable interest in applying in situ leaching technology to recover copper from oxide ores. In many instances, the distribution of copper mineralization in these deposits is fracture controlled. Laboratory core-leaching experiments have demonstrated that leaching response is sensitive to the dissolution of copper from and the formation of channels along main fractures. Solution short- circuiting can be a major limitation of this technology. This paper describes the application of macromolecular polymers to achieve flow-profile control during leaching. Pre- and post-leached fractures were characterized by computerized tomography (CT) analysis.

Jan 1, 1993

By David McGregor, Ashoke SenGupta, Jerry Darlington

The stability of bentonite clay suspensions against flocculation in the presence of certain anionic polymers was investigated. These polymers included a purified sodium lignosulfonate, a sodium oxylignosulfonate, a potassium salt of humic acid, and a sodium polyacrylate. The polymers differed from one another in molecular weight as well as in carboxylic, phenolic, and sulfonate group contents. The scope of this study is in evaluating the extent of thinning achievable in a bentonite clay suspension in the presence of these anionic polymers under varying electrolyte concentration, presumably as a result of deflocculation of the clay platelets by the polymers. Under certain conditions of polymer dosage and electrolyte concentration, the lignosulfonate seemed to have flocculated the clay suspension, while the other polymers served fairly well as a deflocculating/dispersing agent. The lignosulfonate, however, showed some deflocculating ability when the electrolyte concentration of the suspending medium (water) was increased by adding sodium chloride to the clay suspension. Among the four polymers tested, the polyacrylate was found to be the most effective in deflocculating clay particles, followed by the humate and the oxylignosulfonate.

Jan 1, 2003

By William H. Pomroy, Annie M. Carigiet

This U.S. Bureau of Mines report is an analysis of underground coal mine fire incidents occurring in the United States during the 15 years from 1978 through 1992. The fire data used in this analysis were obtained from Federal Mine Safety and Health Administration (MSHA) mine fire investigation reports. Fires were analyzed by year, state, coal bed thickness, mining method, evacuation measures taken, ignition source, burning substance, location, equipment involved, detection method, time of day, number of injuries and fatalities, and method of extinguishment. In all, 164 fires are reported, or an average of 10.8fires per year. The most common ignition source was electricity, the most common burning substance was coal, the most frequent fire location was the belt entry, belt conveyors were the most common equipment involved in fires, and water was the most common extinguishing agent.

Jan 1, 1995

By James L. Noble

A small placer operation can be defined as one with a throughput capacity of 250 cubic yards an hour or less. The success of small placer operations after the values have been established, depend entirely on having the proper design. There are various types of placer deposits including marine, beach, desert, stream, bench, underground and even frozen placers. Each is unique and requires special considerations. Size distribution of alluvial placer ore varies from sand to large boulders. When boulders occur, they can become a problem to all types of excavating to a greater or lesser degree. Clay content and cementing are common in placer deposits. Some clay disperses easily in water while others, if not handled properly, will form clay balls that pick up gold and carry it to tailings. Overburden, depth of bedrock, vegetation, and ground and surface water must all be considered when designing a plant. Any equipment chosen should be capable of processing large volumes of material at a high efficiency. There are usually five steps to processing placer gravels, as follows:

Jan 1, 1992

By D. J. Kennedy, W. G. Klinowski

Over the past few years the Cape Breton Coal Research Laboratory's staff designed, built, tested and proved the necessary hardware, software and methodology of tracer gas based surveying techniques applied in the field of mine ventilation. These methods are now used routinely in a variety of applications where traditional anemometric methods do not provide the required accuracies or cannot be effectively employed. Irregular or highly turbulent flows, leakages, geometrically complicated or highly obstructed airways are just a few examples where traditional anemometry can produce unacceptable errors in calculated ventilation parameters. Tracer gas based ventilation techniques have been used in many problematic situations where the standard ventilation methods are inadequate. One such problem, faced by many mine operators, is the emergency imposed by the ever present threat of a mine fire. An understanding of the propagation of smoke contaminants and the demonstrated integrity of appointed escape routes can save lives and property during a fire. That knowledge can be gained quickly and inexpensively by the application of tracer gas smoke simulation methods. The concept of controlled air recirculation has recently gained considerable attention in the mining industry. While mathematical models can be used to predict performance, the ultimate proof of a ventilation system's performance can best be provided by a tracer gas based simulation of contaminant levels. Fan performance tests and assessment of auxiliary ventilation systems are highly dependent on accurate definition of airflows; precise data can be easily obtained by tracer gas based volumetric surveys. This paper contains a brief description of the equipment and the methodology of tracer gas based ventilation techniques and presents typical examples of their use

Jan 1, 1991

By D. R. Maneval

The vast coal resources of North Slope, Alaska, can be expected to attract substantial interest because the nearly flat-lying coal beds of the coastal plain are specially amenable to surface mining. Mining on a scale large enough to justify coal development in this area could have severe environmental effects. The mitigation would be uncertain because large-scale coal mining and reclamation operations have not been carried out in the arctic. The deficiency of the scientific data base is another factor that requires consideration if coal mining has to develop in accordance with the objectives of PL 95-87. The objective of this paper is to establish the inter-relationship between the problems due to permafrost and factors in reclamation of post-mining land in order to find ways to transform nature in a rational and purposeful manner and to suggest specific reclamation approaches that may be appropriate in this region.

Jan 1, 1987

By Raj K. Rajamani, Poly K. Songfack

The slurry transport within the ball mill greatly influences the mill holdup, residence time, breakage rate, and hence the power draw and the particle size distribution of the mill product. However, residence-time distribution and holdup in industrial mills could not be predicted a priori. Indeed, it is impossible to determine the slurry loading in continuously operating mills by direct measurement, especially in industrial mills. In this paper, the slurry transport problem is solved using the principles of fluid mechanics. First, the motion of the ball charge and its expansion are predicted by a technique called discrete element method. Then the slurry flow through the porous ball charge is tackled with a fluid-flow technique called the marker and cell method. This may be the only numerical technique capable of tracking the slurry- free surface as it fluctuates with the motion of the ball charge. The result is a prediction of the slurry profile in both the radial and axial directions. Hence, it leads to the detailed description of slurry mass and ball charge within the mill. The model predictions are verified with pilot-scale experimental work. This novel approach based on the physics of fluid flow is devoid of any empiricism. It is shown that the holdup of industrial mills at a given feed percent solids can be predicted successfully.

Jan 1, 1995

By Gerald H. Luttrell, Joe Shoniker, Jaisen N. Kohmuench, Christopher J. Barbee, Michael J. Mankosa

The HydroFloat technology was specifically developed to upgrade phosphate sands that are too coarse (>0.6 mm) to be efficiently recovered by conventional flotation methods. In this novel process, classified feed is suspended in a fluidized bed that has been aerated using an external sparging system. The air bubbles selectively attach to particles that have been made hydrophobic through the addition of a fatty acid collector. The teetering effect of the fluidized bed forces the low-density bubble-particle aggregates into the overflow, while hydrophilic particles are rejected as a high solids content underflow Since the HydroFloat is actually a density separator, the process can treat much coarser feeds than would be possible using traditional flotation processes. In addition, the high solids content of the teeter bed promotes bubble-particle attachment and reduces the cell volume required to achieve a given capacity. This paper presents test data from ongoing pilot-scale trials of the HydroFloat cell in the phosphate industry.

Jan 1, 2002

By A. C. Kunkie, C. J. Marshall

Highly delaminated muscovite mica products (WG-1 and WG-2) have been developed by J.M. Huber Corp. The micas are characterized as a 325-mesh product having high brightness and very narrow particle size distribution. At 40% loading in polypropylene, WG-1 mica provides substantial improvement in tensile modulus and equal tensile strength to unfilled polymer; in high-density poly- ethylene (HDPE), WG-1 provides four times the tensile modulus and a 50% increase in tensile strength over unfilled polymer. Surface modification of the water-ground mica (SM ™) provides substantial improvement in tensile strength over untreated mica at greater than 20% loading in polypropylene; in HDPE, tensile strength is twice that of unfilled polymer.

Jan 1, 1988

By Michael J. Nicol

Hydrometallurgical processes involve the recovery of metals from ores, concentrates, calcines, mattes and scrap materials by a series of operations involving leaching or dissolution, separation, purification and reduction of metals in aqueous solutions. The underlying theoretical basis of many of these operations is electrochemical in nature and it is the purpose of this review to identify and illustrate, by way of examples from the author's experience and that of others, the central role of interfacial electrochemistry in the understanding, design and control of these operations.

Jan 1, 1993

By M. Balakrishnan, K. A. Natarajan, J. M. Modak, J. S. Gururaj Naik

The ability of various fungal species isolated from gold mines to uptake gold and base metals such as zinc, copper, iron and lead from gold-process cyanide effluents was investigated. Under identical treatment conditions, different strains showed wide variations in their ability to take up gold and other base metals. Aspergillus terreus exhibited as high as a 60% gold uptake. Almost complete removal of zinc was possible with various fungi and with the yeast Saccharomyces cerevisiae. Studies at various metal concentrations showed a higher gold uptake from dilute solutions, and studies with Aspergillus niger showed that gold uptake by living cells increased gradually as the contact time increased. Metal uptake capacities between living and nonliving cells were also compared. A waste biomass (ABM- I), obtained from a fermentation industry, wasalso identified as having a high gold uptake capacity. At 5% (W/v) solids, ABM-I could efficiently remove up to 83% of the gold contained in an effluent solution within 24 hrs.

Jan 1, 1995

By John T. Gormley, Pressley L. Campbell, Harry L. Crouse

INTRODUCTION This paper summarizes an investigation conducted to determine the relationship, if any, between reported occurrences of abnormal levels of carbon dioxide (C02) gas and the construction of a 2.44meter diameter main sewer tunnel under South Eighty-Fourth Street, West Allis, Milwaukee, Wisconsin. Specific objectives of the study were to determine: (1) the sources of C02, (2) the significance of each C02 source, (3) how C02 could move to areas where it was reported to occur in abnormal concentrations, and (4) what actions could be implemented to eliminate elevated C02 levels associated with the tunneling operation. To accomplish study objectives, expertise from several scientific and engineering disciplines was required including chemistry, geochemistry, microbiology, hydraulics, and hydrology. Pertinent documents were reviewed and field data pertaining to each aspect of the study were collected as required and examined to evaluate existing conditions. Background On or about February 1, 1971, gas with a composition different from normal atmospheric air was reported to enter basements and wells of residences in the vicinity of South Eighty-Fourth Street, West Allis, Wisconsin. Examination of the gas composition revealed that it possessed an elevated concentration of C02 and a depleted concentration of oxygen (02). Public health officials who investigated the appearance of the objectionable gas concluded within reasonable certainty that the elevated C02 concentrations were associated with the tunnel construction under Eighty-Fourth Street.

Jan 1, 1979

By A. D. Davis, C. J. Webb, T. V. Durkin

This project took a watershed approach in the evaluation of water-quality impacts from past mining activities and current restoration projects in the Bear Butte Creek basin, a small and well-defined drainage in a heavily mined area of the northern Black Hills. The basin contains numerous inactive and abandoned mines, as well as a heap-leach surface gold mine. Bear Butte Creek normally loses all of its discharge to sinkholes in the Madison Limestone aquifer. Thus, it can affect the water quality of this regionally important water resource. Water-quality data were analyzed, stream surveys were conducted and two abandoned-mine restoration projects were monitored to evaluate the effectiveness of the watershed approach and to identify practical remediation techniques that could be applied to other watersheds. A geographic information system (GIS) was developed to organize information on stream quality, abandoned mine locations, and other geologic and hydrologic data. The watershed approach toward assessing and reclaiming abandoned mines appears to be effective when compared to a point-source approach that might improve water quality at specific sites but not result in significant overall improvement to the watershed because of adjacent sources.

Jan 1, 2000