Search Documents

By Richard R. Klimpel

This article introduces the basic definitions and philosophy behind process hazard evaluation procedures and the determination of risk as being a function of accident probabi1ity and accident consequence. The general concepts of good engineering practice and predictive hazard evaluation are discussed. The most commonly employed methods used in the processing industries are reviewed with an eye towards briefly presenting what each method offers as far as information, time and resources required, etc. Some initial references on the actual practical use of each technique in the processing industries are also given.

Jan 1, 1991

By Y. H. Cheng, H. EI-shall, S. Gupta, N. A. Abdel-Khalek

A 14.6 cm (5.75 in.) diameter by 1.83 m (6 ft) tall laboratory-size column is used in flotation of Florida phosphates of different feed sizes. In this paper, the effects of different parameters on the flotation efficiency of coarse particles (belt feed, -1.4 + 0.5 mm, i.e., 14 x 35 mesh) under negative bias are discussed. Parameters included collector dosage, frother type and dosage, and conditioning water, which contained a residual concentration of collector. Flotation tests were performed using statistical designs. The results strongly suggest that flotation performance is dependent on the used combination of reagents. Interactions between frothers and the collector and, consequently, the flotation efficiency were found to be dependent on frother type and presence or absence of conditioning water. Under the negative bias, an excellent recovery of more than 98% of phosphate was achieved in concentrates of high grade (above 31% P205) from such feed of coarse particles.

Jan 1, 1999

By D. T. Kinard, A. A. Schweizer

An operational 9 meter (30-foot) high gold heap leach pile was investigated by excavating test pits up to 6 meters (20 feet) deep, obtaining bulk and relatively undisturbed thin wall drive samples, and observing the ore distribution patterns exposed in the test pit walls. The clayey ore is crushed, agglomerated with lime and cement, and deposited on the leach pads using a radial stacker. Laboratory tests performed included moisture-density, gradation, compaction, Atterberg limits, permeability (constant and falling head), and triaxial strength tests. Discussion is presented on the effects of agglomeration on the permeability and strength characteristics of the in-place ore. Also discussed is the effect of deposition of the ore using the radial stacker.

Jan 1, 1987

By L. D. Gehi, A. W. Khair, M. Ahmad

This paper presents an analysis of the dynamics of bit wear on the productivity of continuous miners. Two field surveys were carried out. The first survey assessed the impact of bit wear on productivity and production cost. The second survey studied the wear characteristics of the cutting tool (i.e., magnitude, forms, and mechanisms of bit wear, Primary factors affecting bit wear were identified. Laboratory experiments were carried out to study in detail the effect of some of these primary factors on wear. Results indicate, that bit wear has a significant effect on the productivity a continuous miners. Furthermore, under severe geologic conditions (i.e. cutting rock partings in roof and floor) bit wear not only hampers the productivity, but also increase the production cost due to a higher consumption of bits. This study also indicated that beyond 20% of the conical height loss (which corresponds to 7% of the weight loss) the rate a bit wear accelerates. This increased rate of wear is an indication of higher abrasion between bit body and cutting material, resulting in a dustier environment.

Jan 1, 1995

By Ken A. Pfaff, Ray Daigh

This paper will discuss state-of-the-art applications of GPS automation in mobile conveying systems. Robotic mobile conveying systems increase profitability, optimize stacking and reclaiming operations, and control complex interfaces more accurately than other systems. We will also discuss the application process in machine-to-machine coordination, selection of the appropriate GPS system, and Ethernet considerations. As the leading supplier of GPS-controlled mobile conveying systems, we'll draw on our experience at Morenci, Radomiro Tomic, Zaldivar, El Abra (Figure 1), and El Tesoro mines in the US and South America to demonstrate system reliability and the lessons we've learned through analysis of these projects.

Jan 1, 2002

By Kirk H. P. E. McDaniel, Mark T. Strever, Keith G. Jr. Wallace

This paper presents the design and installation of an underground ventilation remote monitoring and control system at the Waste Isolation Pilot Plant. This facility is designed to demonstrate safe underground disposal of U.S. defense generated transuranic nuclear waste. To improve the operability of the ventilation system, an underground remote monitoring and control system was designed and installed. The system consists of 15 air velocity sensors and 8 differential pressure sensors strategically located throughout the underground facility providing real-time data regarding the status of the ventilation system. In addition, a control system was installed on the main underground air regulators. The regulator control system gives indication of the regulator position and can be controlled either locally or remotely. The sensor output is displayed locally and at a central surface location through the site-wide Central Monitoring System (CMS). The CMS operator can review all sensor data and can remotely operate the main underground regulators. Furthermore, the Virtual Address Extension (VAX) network allows the ventilation engineer to retrieve real-time ventilation data on his personal computer located in his workstation. This paper describes the types of sensors selected, the installation of the instrumentation, and the initial operation of the remote monitoring system.

Jan 1, 1995

By W. A. Heitbrink, M. Schmitz, J. A. Organiscak, A. B. Cecala, E. Ahrenholtz

Mobile excavation equipment operators at surface mines generally have the highest exposure to airborne respirable silica dust. Operator cabs on newer equipment are usually enclosed and equipped with heating and air conditioning systems. Many newer cabs are also equipped with air filtration systems. However, some newer cabs and many older cabs have either inefficient or no air filtration systems. The U. S. surface mining industry is still populated with older equipment and many of these have cabs that provide little or no respirable silica dust protection. Collaborative field studies were conducted as part of a partnership involving NIOSH, Clean Air Filter®, Red Dot, MSHA, and several mine operators to demonstrate that effective dust protection can be provided by these cabs at a nominal cost to mine operators. This effort encompassed adding an external make-up air fan and filter system to a retrofitted roof-mounted heating and air conditioning system in three older equipment cabs, and attempting to seal the cab enclosures to achieve interior cab pressurization. Abetter than 90 percent dust reduction was measured inside two of the three enclosed equipment cabs. It was possible to achieve positive cab pressurization inside these two cabs. A less significant dust reduction was measured inside the third cab, where positive pressurization was not achieved. These field studies demonstrate the key elements needed to improve enclosed cab dust protection in a cost-effective manner.

Jan 1, 2003

By F. Gonzalez, A. Zambrano, J. Schwoebel, S. Kravits

Significant lost time delays were experienced by Carbonifera de Nueva Rosita, S.A. de C.V. ("CNR") during mining development of the Pasta de Conchos Mine ("the Mine") near Nueva Rosita, Coahuila, Mexico. Furthermore, methane gas concentration in the return air course had exceeded 1.0 percent. Resource Enterprises, Inc. ("REI") was contracted by CNR to recommend an approach to reduce methane emissions at the Mine. In order to recommend a degasification approach, REI and CNR obtained geologic and reservoir characteristics of the Double coal seam, Olmos Formation. A vertical core hole was drilled to obtain core samples to determine gas content (average 8.4 cm3/gm) and to conduct a slug test to estimate permeability (34 md). This information was used to simulate gas productivity and drainage effectiveness. The simulation indicated that underground horizontal boreholes would remove significant quantities of gas in advance of mining in a reasonable period of time. Based on the results of the simulation study, an underground degasification drilling program was initiated at the Mine. In a six month period, five long in-mine degasification boreholes were drilled in advance of CNR's three to five years mining projections. Peak gas production from the five boreholes (approximately 2,750 cumulative meters) had exceeded 45,000 m3/D. Results to date have indicated a general reduction in methane concentration in the return air course below 0.8 percent.

Jan 1, 1993

By S. R. Bryan, J. D. Stephens, D. R. Rothbard

The distributions of gold and associated elements in mineral grains from a pyritic gold ore were studied by optical microscopy, and by SEM and SIMS imagery. Products studied were a sulfide flotation concentrate, a calcined sulfide concentrate, a cyanide leached calcine, and a cyanide leached pressure oxidation residue. Individual pyrite grains are compositionally zoned and solid solution gold occurs in some, but not all zones. Most of the gold in calcined products is present as metallic coalesced grains that are smaller than 100 angstroms. Gold lost into cyanide leached residues from the calcines tends to be in “semi-dense” grains that cannot be distinguished from gold-free grains except by SIMS analysis. The gold in cyanide leached pressure oxidation residues occurs as solid solution gold in unoxidized pyrite remnants.

Jan 1, 1990

By Ralph P. Hackl

The Congress gold property, located near Goldbridge, B.C., is extremely refractory with most of the gold disseminated in fine- grained arsenopyrite. Metallurgical testwork conducted by Giant Bay Biotech Inc. indicated that biooxidation pretreatment was capable of increasing cyanide gold recovery from the ore to greater than 90%. To determine if the bioleach process could be successfully scaled up, a 225 cubic meter commercial size bioleach reactor was built and tested at the mine site in 1989. At that time the tank was the largest bioleach reactor ever operated. This paper discusses our experiences in operating the tank, summarizes some of the data obtained and describes the problems encountered.

Jan 1, 1990

By J. M. Dean, R. L. Grayson, R. D. Begley, G. L. Winn

Evidence has accumulated indicating that cultural change toward safer workplace behaviors is beginning to occur systematically in the coal industry. Through a range of programmatic mining company successes, enforcement and litigative actions, economic responses to competition and integrated efforts by federal and state agencies, a broader participation of safety and training professionals is being achieved to address prioritized workplace problems at mines. Small steps in workplace-related improvements have been realized already, but the trends in industry safety statistics, coupled with focused programmatic initiatives, indicate that more definitive and systematic steps are occurring to improve safe behavior in the workplace routinely.

Jan 1, 1998

By Wilson I. L. Lim, Jonathan J. Campbell, Luis A. Tondo

An important issue in the use of high pressure grinding rolls when grinding ores is wear of the rolls. Due to the abrasive nature of the ores, significant wear rates have typically occurred. Attempts to address the wear problem require a better understanding of the wear mechanisms. A probable wear mechanism is the abrasion of the rolls surface due to extrusion of the compacted material as it leaves the rolls. This paper presents the results of a study on a number of ores to examine the extent of extrusion that occurs. The study involved laboratory, pilot and full-scale high pressure grinding rolls. The effect of variations in parameters such as grinding pressure, rolls speed, initial gap settings, feed topsize and moisture was investigated. The results indicate that extrusion increases with increasing grinding pressure and rolls diameter, while the use of studded or profiled rolls significantly reduces the extrusion effect compared to smooth rolls. It was also found that rolls speed and feed moisture can have significant effect on extrusion, depending on the material.

Jan 1, 1998

By J. Pang, S. Chander

The results of an investigation to characterize the chalcopyrite/solution interface are presented. Several techniques were used, including galvanostatic and steady-state polarization, cyclic voltammetry and impedance spectroscopy. The results show that the dissolution of chalcopyrite was incongruent. Initially, at low potentials (< 0.12 V), iron species were released that led to the growth of an iron-deficient sulfide (IDS) layer (referred to as the "reacted layer" in this paper). Depending on the solution&apos;s composition, the dissolved iron might reprecipitate as a hydroxide layer. In the potential range of 0.12 V < E < 0.23 V, the IDS layer was passivating. In comparison, development of a passivating IDS layer under galvanostatic conditions led to a jump in potential to 0.48 V. The IDS layer began to dissolve at potentials greater than 0.24 V. The dissolved species precipitated to form a product layer in alkaline solutions. Continued oxidation involved diffusion of species through the reacted and product layers. At higher potentials (> 0.48 V), further oxidation led to the dissolution of the copper and sulfur species, with a resultant breakdown of the IDS layer. The changes in surface-coating properties, resulting from various electrochemical treatments, are discussed.

Jan 1, 1993

By Charles P. Lazzara, Alex C. Smith, Mark W. Ryan

The U.S. Bureau of Mines developed an experimental method to evaluate the relative effectiveness of water additives on the extinguishment of coal fires. The experiments were conducted in the fire zone of the multiple entry section of the Bruceton Experimental Mine. Chambers filled with one hundred and eighty kilograms of Pittsburgh seam coal were ignited and allowed to burn until well developed fires were achieved. Extinguishing agent-water solutions were then applied to the fires and the quantity required to extinguish the fires compared to the amount of water alone required to extinguish similar fires. A 20% diammonium phosphate-water solution required an average of 22 L to extinguish the coal fires, while two commercially available additive-water solutions required an average of 30.6 and 30.3 L, respectively. The average amount of water required to extinguish the fires was 28 L. An analysis of covariance, using the thermal energy of the coalbed, Q, to quantify the fire at the time of extinguishment, showed that the diammonium phosphate-water solution was slightly more effective at extinguishing these coal fires than water alone, while the two commercially available additive-water solutions were statistically equivalent to water alone.

Jan 1, 1992

By W. J. Wuest, M. J. DeMarco, J. R. Koehler

Yield-pillar-based gate-road designs often fail to provide mine operators with adequate ground control. This is because of the unknowing m is employment of "critically" sized pillars. A "critical” pillar is one that is too large to either yield nonviolently or to yield before the roof and floor sustain permanent damage and is too small to support full abutment loads. To demonstrate the critical pillar concept, afield study of a tapering gate road was conducted by the US Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m (55.1-ft) wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m (40-ft) wide design more closely approaches proper yield pillar dimensions. A probe hole in several 10.6-m (34.8-ft) wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1997

By Bryan Morris

Quebrada Blanca (QB) is a copper project located in the semi-arid Andean highlands of northern Chile. The operation is situated 170 km ( 105 miles) southeast of the port of Iquique and 30 km (18 miles) west of the border with Bolivia, at an altitude of about 4300 m (14,000 ft) (Fig. 1). The QB ore body is a secondarily enriched porphyry copper deposit containing reserves of 85 Mt (93 million st) grading 1.3% copper. Underlying the enriched zone is a significant primary ore zone containing several hundred million tons grading about 0.5% copper. In the late 1970s and early 1980s Falconbridge and its affiliates spent $20- $30 million exploring the deposit and conducting feasibility studies. Falconbridge, however, decided not to develop the property. It was returned to its owners, Empresa National de Mineria (ENAMI), a Chilean state mining corporation. In 1988, ENAMI announced its intention to privatize the property through public bidding. Cominco Resources, then 61% owned by Cominco Ltd., examined the property and the extensive data base developed by Falconbridge. In conjunction with its parent company, Cominco Resources submitted a proposal to ENAMI to construct an open- pit mine, with heap leaching and solvent extraction/electrowinning (SX-EW) processing facilities. The plan would use patented heap leaching technology developed by Sociedad MineraPudahuel (SMP), a privately owned Chilean mining company. At that time, a $150-million project that would produce about 45 kt/a (50,000 stpy) of cathode copper was envisaged.

Jan 1, 1993

By David J. Brown, Richard C. Fountain, Marc V. Hurst

The Central Florida Phosphate District, one of the most productive phosphate districts in the world, has been mined principally within Polk and Hillsborough Counties, Florida. Recent development is extending the district southward into Hardee, Manatee, and DeSoto Counties. This area is known as the Southern Extension. The combined area of these two phosphate-bearing areas encompasses about 2,000 square miles. Structurally, the district and its Southern Extension lie at the southern end of the Ocala Arch and are flanked by the Hillsborough High to the northwest. South of this area is the South Florida Embayment. The Osceola Low lies to the east. The phosphorite within the Central Florida Phosphate District generally dips very gently (<0.1°) to the south. The boundaries of the central Florida Phosphate District are generally defined by thinning of the phosphorite due the adjacent structurally high areas to the north, west, and east, and by increased clay, CaO, and MgO content reflecting lithologic differences to the east and south. The Bone Valley Member of the Peace River Formation and reworked sediments of more recent age were the primary ore-bearing horizon in the Polk-Hillsborough County area. As those reserves are depleted, the less desirable phosphorites of the Peace River Formation are being exploited in the Southern Extension.

Jan 1, 1993

By J de Cuyper, E. J. Parkins, H. L. Shergold, W. Freyberger

The paper is divided into two parts. The first part describes an investigation of the effect of temperature on the conditioning and flotation of an ilmenite ore with a 1:l oleic acid-fuel oil mixture as collector. During conditioning the pulp underwent characteristic changes of flocculation, deflocculation and dispersion which were monitored by measuring the power consumption of the conditioner motor. Optimum flotation results were obtained at the end of the deflocculation period. High ilmenite recoveries were obtained at high temperatures and high concentrate grades at low temperatures. The second part of the paper describes a study of the effect of temperature on the adsorption of oleic acid at the ilmenite/water interface. At high adsorption densities it was chemical and exothermic. Contact angles showed that the hydrophobicity of the collector-coated minerals increased with an increase in temperature.

Jan 1, 1976

By Alain GSELL

The aluminous nature of the laterites capping the Minim Martap plateaus - named after two neighbouring villages - and the small nearby upland of Ngaoundal, was discovered by the Cameroon Mines and Geology Division in 1958. These deposits of worldwide importance, are located in the Ngaoundere region, some 500 km (300 miles) north-east from the port of Douala (as the crow flies). They constitute the major part of the Cameroonese mining potential. The study of the deposits and their economic development has been entrusted to SEBACAM, Societe d&apos;Etudes des Bauxites du Cameroun, a company in which the Cameroon government participates. The bauxites originate from the transformation into laterite of lavas which covered a Precambrian basement during the Upper Cretaceous period and the Lower Tertiary era. The entire Minim Martap deposit comprises bauxite plateaus ranging in area from a few acres to several square miles. The average thickness of the bauxite layer varies from 10 metres at Minim Martap to 17 metres at Ngaoundal. The mineral constituents of the bauxite are gibbsite trihydrate, kaolinite and the usual iron and titanium oxides. Treatment of the ore does not involve any particular technical problems. Proven exploitable reserves amount to 560 million tonnes of dry bauxite with a reactive silica content of 1.80% and an available alumina content of 43.70% at Minim Martap, and 120

Jan 1, 1984

By Ronald E. Heuer

The significance of surface settlement over soft ground tunnels is well recognized. Cracked buildings, streets transformed into lakes, broken utility lines, to underpin or not to underpin--all are familiar problems. The basic causes of surface settlement are recognized. Possibly the most common and troublesome cause is "lost ground" during construction. Lost ground refers to removal of a larger volume of ground (Ve) than is eventually occupied by the final tunnel structure (Vt). A number of sources of lost ground in shield tunneling have been identified, as illustrated in Fig. 1. These include 1) face loss, 2) overcutting loss, 3) annular tail void loss, and 4) loss through the lining. The ground generally does not stand unsupported around the completed tunnel lining as illustrated in Fig. 1, but moves in to fill the lost volume, resulting in subsidence of the overlying ground surface as shown. As suggested in Fig. 1, lost ground and surface settlement associated with overcutting and the annular tail void tend to occur systematically along the tunnel length. This "systematic" lost volume is "limited" in the sense that it is restricted to an upper limit determined by the shield and lining geometry. Partially controlled face loss may sometimes contribute to this systematic loss. This lost volume is commonly a few percent of the nominal tunnel volume. The resulting surface settlement over the tunnel is commonly in the range of a few inches or less and develops over a period of hours to days. Although they may have a significant impact on surface facilities, systematic ground loss and settlement frequently have little adverse effect on tunneling progress.

Jan 1, 1976