Search Documents

By Edward C. Dowling

Cleveland Cliffs and affiliated companies have established a commitment to the development and use of integrated process control. Substantial capital investments in process control, coupled with the dedication of human resources to effectively use the information, have generated meaningful business results. Improvements in productivity, operating costs and product quality have been realized. This paper presents an overall process control and information strategy, specific case studies, lessons learned and the current view of the next steps in the continued journey toward integrated process control and information management.

Jan 1, 2000

By Robert G. Moorhead

Fine-coal screening can be one of the most critical operations in a modern coal-cleaning plant. The yield and quality of clean coal produced in fine-coal circuits is controlled as much by how efficiently 0.15 mm (100 mesh) particles are sized as on the performance traits of the fine-coal cleaning device itself. In addition, the increased interest in effective fine-coal sizing operations indicates that many operators have also discovered its importance in affecting the quality and yield of clean coal produced in fine-coal circuits. This paper describes the three most prevalently used fine-coal screening technologies and discusses their sizing mechanism, performance, and application.

Jan 1, 1988

By O. Olajide, E. H. Cho

A laboratory study of the jigging process with Pittsburgh seam coal has been conducted. The laboratory-scale Baum jig used in this study was a McNally-Norton LO30X Right Hand Model Baum jig with an effective screen area of 0.186 m2 Feed material was prepared by selecting a size range from 6 mesh to 1.91 cm. Solid feed rates were 27.2 kg/min and 32.7 kg/min. Water flow rates were varied from 37.9 to 94.6 L/min. It has been found that smaller particles give higher values of density of separation and lower efficiency of separation. Increasing water flow rate increases the discharge rate of clean coal at a constant solid feed rate. It appears that the efficiency of separation increases by increasing water flow rate up to a certain value, and then levels off upon increasing the flow rate further.

Jan 1, 1988

By H. K. Lin

Cyclic voltammetric and potential step chronoamperometric techniques were used to study gold dissolution in cyanide solution. Three distinct anodic peaks and one cathodic peak appear on the voltammogram between -0.50 and 0.80 V vs. SCE. The corresponding reactions were proposed to explain the peaks and the passivations. The proposed reactions were in agreement with the effect of pH and cyanide on the magnitude of the peak currents. Cyclic voltammetric tests, with various vertex potentials, were also conducted to examine the proposed reactions. Steady-state currents at various potentials were obtained by potential step chronoamperometric technique and were compared with transient currents obtained by the cyclic voltammetric technique.

Jan 1, 2002

By George J. Bujtor, Anthony K. Scott, Haddon F. King

In 1982, the result of a 3-year study was published as "A Guide to the Understanding of Ore Reserve Estimation". The principal conclusions were that computation formed only part, and perhaps not the most important part, of an estimate and that the estimate should recognize that geological, mining engineering and metallurgical judgements formed an essential part of the eventual result. Subsequent expectation/realization studies of several mines have produced case histories which form the principal basis of the paper. These imply that geology is even a larger factor than thought earlier.

Jan 1, 1992

By Mike L. Aziz, Keith D. Ferguson, Glenda Ferris

The Equity Silver mine has been a severe producer of Acid Rock Drainage (ARD) since 1982. The mine was closed in 1994 and a compacted clay cover installed, but ARD continues to be produced. Three permanent employees manage the collection and treatment system at the site. The site still poses a significant environmental risk to the environment and downstream users and requires a high level of diligence. Various stakeholders' perspectives of the risk posed by Equity, and what constitutes acceptable risk, will be examined in this paper from a company operation staff, corporate environmental manager and downstream environmentalist perspective.

Jan 1, 2000

By Leonard W. Postregna

Prior to January, 1986, the city of Austin, Texas was on notice by the Federal Government's Environmental Protection Agency and the Texas Water Commission, that they were illegally polluting the Colorado River. The wastewater facilities presently in use in South Austin were inadequate to handle the vastly increasing population. The city of Austin, Texas hired Parsons Brinckerhoff Quade and Douglas, Inc. and Dannenbaum Engineering Corporation to design and supervise the construction of an update to their existing system to alleviate this problem. A major criterion handed down to the Designer and Contractor was that the system had to be completed within a two year time frame. The biggest link to the entire design was a tunnel project consisting of 43,000 linear feet (13,106 m) of tunnel, eight feet (2.44 m) in diameter with connecting structures tying into existing and future facilities. The project was awarded to S. A. Healy Construction Company of McCook, Illinois with a low bid of $24,755,000.00. This article summarizes the techniques used in the construction of this tunnel project.

Jan 1, 1989

By D. W. Fuerstenau, J. Vazquez-Favela

This paper shows how the efficiencies of size-reduction processes depend on the mode of particle constraint and energy transfer within the comminution device: namely, whether the process consists of single-particle loading, confined-particle-bed comminution or loose- (unconstrained-) particle grinding. The relative efficiency of single-particle comminution, ball-mill grinding and particle-bed comminution in the recently invented high-pressure roll mill is evaluated by making use of the self-preserving nature of the size distributions of comminuted products. The highest energy efficiency can be achieved by utilizing a hybrid two-stage system in which the material is first ground in the high-pressure roll mill and then the ball mill.

Jan 1, 1998

By Yannis Faitakis, Brenda M. Wright, Gail Powley, Mark Hamblin, Randy B. Paine

A major problem in the ore extraction process is the high degree of variation in the mix of materials that make up the mined ore. The mix of materials makes it extremely difficult to characterize and predict the behavior of the ore when it is processed. The Quality Production Database (QPD) tool was successfully used in order to predict and transfer information regarding the quality characteristics of the ore being delivered to the extraction and hydrotransport unit operators. This paper describes the use of QPD in the prediction of various ore characteristics at the Syncrude Canada Ltd. processing facility.

Jan 1, 2000

By Robert B. Gordon

The Reverse Curve Tunnel Project was located in Glenwood Canyon, Colorado approximately twelve (12) miles east of Glenwood Springs. The Project was one of many being constructed over a period of time by the State of Colorado, Department of Highways to improve Interstate 70 to four lanes as it travels thru the environmentally sensitive Glenwood Canyon. The Project consisted of excavating and concreting a tunnel approximately five hundred fifty (550) feet long, forty two (42) feet wide, and thirty two (32) feet high. The designer was Parsons, Brinkerhoff, Quade and Douglas, with geotechnical consultation provided by Woodward Clyde. CONSTRUCTION CHALLENGES There were several significant construction challenges presented primarily by the physical location of the Project. In this study each problem will be discussed, as well as how it was overcome by construction methods and/or design requirements. Portal Excavation - One of the most difficult areas of work on the Project consisted of excavation and stabilizing the East and West Portal rock prior to tunnel excavation. The Reverse Curve Tunnel passes through a sheer walled cliff face which is approximately two hundred fifty (250) feet high. Geologically the cliff consists of primarily sedimentary deposits with open, weathered joints and vertical faulting. Before the tunnel excavation could begin, a narrow sliver cut had to be excavated and rock

Jan 1, 1989

By I. S. Parrish, D. W. Kappes, G. G. Austin

Micron-sized gold disseminated in lower Cambrian siltstone has been found at the Sterling mine near Beatty, NV. A shoestring-shaped body has been developed by central and fringe drifts and is being mined via a modified retreat room and pillar system. The siliceous ore crushed to 5.08 cm (2 in ) is stacked to 4.6 m (15 ft) over a layered sand, gravel, and impervious PVC base. Gold is leached using a 0.1% cyanide solution and deposited on activated coconut shell carbon. Stripping of the carbon by hot solutions of 1% NaOH and 20% Ethanol yields overall recovery of about 75% of the fire assay head.

Jan 1, 1983

The processing capability of a semi-autogenous (SAG) mill is greatly affected by ore geology and operating variables within the mill. The SAG mill is problematic because it cannot be conveniently studied on a smaller, laboratory-scale mill. The interior of the mill, where grinding takes place, cannot be observed using instrumentation available today. Yet the motion of the rock and ball charge determines the power draft and hence capacity of the mill. Therefore, mill optimization is pursued with a charge motion simulation software. This software uses the discrete element method to describe the individual motion of numerous ball and rock particles in the mill. It is shown that by simply increasing the chord length between the lifters and increasing the face angle of the lifters the capacity of the mill can be increased. Such a configuration of lifters allows the operator to increase mill speed, hence drawing higher power while considerably minimizing direct ball strikes against shell plates and lifters. A case study of a 36 ft. diameter x 15 ft. long mill is presented. Reducing the direct ball strikes leads to lesser steel consumption both in terms of balls and lifters.

Jan 1, 2000

By William D. Leech, Peter S. Buskirk

Virginia Electric and Power Company commencing in early 1985 will begin operating the Bath County Pumped Storage hydroelectric facility, presently the largest capacity installation of its kind. Six concrete lined vertical shafts, 3 ea x 44.0 ft (13.4m) diam x 330 ft (100m) and 3 ea x 28.5 ft (8.7m) diam x 740 ft (226m), comprise a portion of the three underground power conduits. The project team decided to employ the slipform over the conventional jump form method. This selection was based on the engineer's hydraulic design and the contractor's performance requirements. This paper presents the key elements of the shafts' successful slipform operations. The contractor achieved slip rates as high as 60 ft (18m) per day; and the owner received competent permanent linings as specified by the engineer. The authors describe the team's effort to progressively improve both concrete quality and placement rate.

Jan 1, 1985

By H. Sis, S. Chander

The pressure filtration behaviors of dispersed and flocculated alumnae slurries at high percent solids were investigated with the objective of determining the effect of surfactant type and concentration on slurry properties. A high-purity alumina powder was used as a model solid. Dispersion of the alumina was controlled by pH and by surfactants that are known to act as electric and steric stabilizers. The effects of both ionic and nonionic sutfactants were investigated. Surface charge measurements of the slurries were carried out by an electrokinetic sonic amplitude (ESA) method to better understand the mechanisms. The effect of surfactant type and concentration on the kinetics of pressure filtration and cake properties are discussed.

Jan 1, 2000

The Peruvian mining industry has seen an explosion of foreign investment since President Albert? Fujimori's government was first elected in 1990. Since then, Peru has taken some large steps toward recovery, making it the envy of most other developing countries. A measure of political stability was gained in 1992 when Shining Path leader Abimael Guzman was captured. In addition, the country has taken on a huge privatization program, rewritten its foreign investment laws and has reined in its annual inflation rate from 1,700% in 1990 to about 8% by late 1997. Small wonder then that attendance at the XXIII Peruvian Institute of Mining Engineers conference reached a record level, many of whom are employed by some of the world's largest mining companies. About 2,700 mining industry professionals from all over the world attended the week-long event, held in late September in Arequipa. That was an increase from 1995s 1,600 attendees, that meeting also held in Arequipa.

Jan 1, 1998

By Salama

In the conventional approach, the separator feed incremental masses are assumed to be concentrated at the midpoints of the density or size intervals and subjected to a model partition function. The resulting separation predictions would change if the locations of the incremental masses were changed. As a result. the predicted results depend on the choice of locations where the feed incremental masses are concentrated in the density or size intervals. A technique that utilizes the cumulative-mass-distribution of the circuit feed and the derivative of the partition (separation) function relative to density or size variables is proposed. The proposed technique eliminates the dependency of the predictions on choice of where the feed incremental masses are concentrated within the density or size intervals. Since the proposed technique is based on the cumulative masses at the upper limits of the density or size intervals, the technique produces a single prediction whereas the existing techniques produce predictions that depend on where the incremental masses are concentrated. In fact, it has been demonstrated that the existing conventional technique, in which the incremental masses are concentrated at the midpoints of the density or size intervals, is a first-order approximation of the technique proposed.

Jan 1, 2002

By Lars Söderberg, Eric Sandström, Per G. Broman

INTRODUCTION Boliden Mineral AB currently mines sulfide ores in 18 mines and processes them in eight concentrators. Most ores are typically complex. Gold consti¬tutes a considerable part of the value of the ore reserves. The value of total production in 1984, distributed by different metals is shown in the pie chart below. Traditionally, gold has been recovered as a byproduct, or coproduct, along with silver in floated copper and lead concen¬trates. Gold-price trends over the past decade have prompted comprehensive efforts by Boliden to increase the recovery of gold in concentration processes. Gravimetric recovery of gold in the grinding circuit is one method that has led to quick results. This method supplements tradi¬tional recovery processes based on flotation. The development of a feasible circuit, and the results obtained by its application in the central concentrator at Boliden, in the northern Swedish province of Västerbotten, are reported below. GOLD MINERALOGY IN BOLIDEN ORES The gold content in Boliden Mineral's ores is primarily in the form of alloys with the elements silver and mercury. A minor quantity appears in an unalloyed form.

Jan 1, 1986

By Andrew T. MacKenzie, Paul A. Rantala

Predictive pastefill rheology (flow characteristic), models have long challenged pastefill practitioners. While the methodology and practicality of recipe formulation is attainable in most locals, the remaining challenge has been to devise a predictive mathematical or empirical model of paste flow characteristics. Flow phenomenon can now be assigned mathematical and physical basis. The authors herein disclose physical and mathematical methods that demonstrate how operators could proceed when designing reliable pastefill systems. Knowledge presented will allow users flexibility in adjusting flow-rates. Laboratory data shows stiff pastefill delivery design can be derived through mathematical relationships of particle size, material characteristics and pipe diameter.

Jan 1, 2001

By P. Riveros, A. Pratt, G. Deschênes

The effect of pyrite, pyrrhotite, chalcopyrite, realgar and arsenopyrite on gold dissolution in cyanide media was investigated. The cyanidation of synthetic gold ores in the presence of various concentrations of sulfides was studied under constant experimental conditions. A mineralogical analysis of the minerals was performed. The leaching kinetics were determined. The negative effect of sulfides on the gold dissolution rate varies with the sulfide mineral and decreases according to the following order: realgar > pyrrhotite > chalcopyrite > pyrite > arsenopyrite. The chemical characterization of gold and sulfide minerals surfaces using X-ray photoelectron spectroscopy (XPS) was undertaken to identify the mechanisms involved. XPS analysis showed that a passivation layer of sulfides, arsenic or iron compounds might form on the gold surface as a result of the dissolution of the sulfide minerals. Key words: Gold dissolution, Cyanidation, Effect of sulfides, Leaching kinetics

Jan 1, 2003

By F. F. Aplan

The material known as coal has a highly variable composition. As a consequence, coals show a great variation in their physical and chemical properties as a function of coal rank. The situation is further complicated because the preparation engineer must deal with raw coal, as mined. This is an assemblage of coal, upwards of 30% mineral matter and, typically, several percent pyrite. The kind and amount of the mineral constituents is also highly variable from source to source. A knowledge of coal rank and source location, and the kind and amount of associated impurities, is the first step in evaluating the response of a raw coal to preparation procedures. The raw coal must first be characterized before information from one source can be extrapolated to that of another.

Jan 1, 1988