Search Documents

By R. V. Ramani, R. Srikanth

A three-part study was conducted to relate the dust generation propensity of a coal sample, defined here as the dust generation rate (grams of dust generated per tonne of coal broken), to its characteristics, in order to rank coal seams according to their respirable dust generation potential. In this paper, the results of a single breakage study on a variety of coal samples encompassing all coal ranks, and samples from operating mines are discussed. Further, where data are available, the primary dust generation rates of coal samples collected from underground coal mines are compared with the in-mine dust generation rates. The results of this analysis are then used to apply the results of this study to longwall face ventilation design. Vitrinite reflectance, and level of organic metamorphism are highly correlated with primary respirable dust generation rates of bituminous coal samples. The dust generation rates in underground coal mines are an order of magnitude higher than the primary dust generation rates in the laboratory. Depending on the type of coal, production rates, and dust control procedures, the air quantity required for airborne dust control can vary significantly. The air quantities on some high production longwalls are approaching the limits beyond which it may not be possible to reduce ambient ARD concentrations to less than 2 mg/m3 by dilution ventilation alone. In these cases, the miner's exposure should be controlled through the use of personal protective de- vices and administrative practices.

Jan 1, 1997

By M. J. Richards, T. X. Ren

Determination of the state of an underground fire plays an important role in fire fighting, rescue and reopening operations. This is normally achieved by the analysis and interpretation of fire gases taken from the fire zone. However, drawing conclusions from gas analysis is not an easy task and needs specialist skills, expertise and experience that are usually beyond the knowledge of the officials in a mine. The complexities of a mine fire and the uncertainties of available information often make effective fire fighting decisions difficult if not impossible. This paper describes a knowledge based expert system that can aid in the diagnosis of sealed coal mine fires. Using a commercially available shell, the expert system has been designed to accommodate a series of diagnostic rules replicating the reasoning logic that would be used by human experts. The system allows the diagnosis of explosibility of the fire zone and trends of various fire ratios to be easily visualised for decision making. By continuously analysing the incoming information, the system is able to provide a rapid assessment of the situation of a sealed mine fire prevailing under specific mining and geological conditions. In addition, short term trends in fire behaviour can be predicted and possible fire control actions recommended. An example is given and shows how this system can be used as an analytical tool in various ways to assist the combating of coal mine fires. Further development of the system is discussed.

Jan 1, 1993

By Ronald I. Fuller

Core Laboratories, a division of Western Atlas International, maintains laboratories in all energy-producing areas of the United States, as well as in many foreign countries. Central to laboratory operations has been the incorporation of computers and computer software. Core has developed a mu1tiuser Laboratory Information Management System (LIMS) , which is currently installed in numerous company sites in the U.S., and is now undergoing installation in Canada. In addition, Core has provided custom soft ware to contract laboratories which Core operates on behalf of mining firms. The software development was done under the direction of the author in Denver, Colorado, and Casper, Wyoming. The intent of this paper is to pass some of the practical experience gained by our efforts on to those who wish to utilize computers more fully in the laboratory setting. The product of analytical laboratories is numbers. Nothing else comes from our work. We deal in information about samples. It is then reasonable to assume that the computer would be central to a laboratory operation. The hard part is to initially define what kind of computer the lab operation needs. The choices today can be very complex, and almost every hardware salesman is full of bad advice. Even the people in your own information services department may hold divided opinions. Since the advent of the personal computer, we have lived with a polarized data processing community. The PC boys consider their machines equal to any challenge, while the "save the mainframe" crowd view the PCs as limited toys that are only good for the things that clutter up a real computer. Management tends to lean toward whatever costs the least.

Jan 1, 1989

By Stephen Utter

One function of mining is to supply oil shale of the required grade and characteristics to surface retorts. The mining methods must he safe, efficient, and environmentally acceptable. Although the Bureau of Mines no longer conducts research on methods of mining fossil fuels, including oil shale, its many years of activity in that field resulted in a significant body of findings. This article summarizes some of these findings, with respect to oil shale mining. The large areal extent of Green River formation oil shales and the diversity of geologic, hydrologic, topographic, and other conditions, preclude the use of any one single mining and waste management technique. Instead, in most instances, methods and equipment will be chosen to meet site-specific conditions. Such methods include conventional surface mining (open-pit and strip), underground mining (room-and-pillar, sublevel stoping, caving) and in situ extraction (true in situ from surface drill holes and modified in situ from underground retorts containing rubblized oil shale). Combination or hybrid systems may prove suitable. Both surface and underground backfilling of spent shale waste may be practiced. Tremendous amounts of oil shale must be mined, processed, and the waste shale properly disposed of in order to meet projected industry production goals. For example, about 1.4 tons of oil shale averaging 117 L of shale oil per ton are required to produce one bbl of oil. A plant with a daily production of 8 dam' (50 000 bbl) of oil would thus require some 68 kt of raw shale daily. This is more than the average daily production from any underground mining operation.

Jan 1, 1981

By C. F. Meyer

The recirculation of mine air in an underground colliery, has always been regarded as a hazardous practice in South African collieries. The Mines and Works Act and Regulations states that fresh air, flowing Into an underground section, must flow out directly into the return airways after being utilized once in the section. One of the largest producing underground collieries in South Africa, Initiated a project on controlled recirculation with the permission of the South African Government Mining Engineer. The project involves the recirculation of 65 m3/s of air inside a ventilation district which serves a total of six production areas. The aim of the project was to increase the airflow to the sections without altering the existing ventilation system. Tracer gas studies were carried out to determine the actual distribution of the recirculated air to the individual areas. The results showed that an effective 54,18 m3/s of the recirculated 65 m3/s reaches the sections. This gives an air utilization figure of 83,4 per cent. Dust surveys were also carried out as part of the project to determine the effect of the recirculation of the return air on airborne dust levels. The results showed that the dust levels remained constant in the main intake and return airways and that no hazardous situation was being created. The project proved to be successful and showed that controlled recirculation can be executed and used as a solution for the supply of air to sections without endangering any lives.

Jan 1, 1993

By John H. Duke

The success of most attempts to evaluate gold orebodies depends largely on the reliability and availability of representative sampling data and the accuracy of geological interpretation. An accurate prediction of the continuity of geology is paramount to a reliable prediction of gold reserves. Many of the problems encountered in gold mine evaluation and planning revolve around the difficulties in interpreting complex geology from sparse drilling data and the eagerness of mine financiers and promoters to start mining in order to derive an early cash flow. Following a program of sampling, geophysics, mapping and geological interpretation, a conceptual orebody model evolves in the minds of those working on the project. It is this model which is used typically in ore reserve computations and mine planning. Computer modelling techniques to represent and evaluate the conceptual model are now available. The main advantages of using computer modelling methods lie in being able to rapidly evaluate, modify and quantify the conceptual orebody model. Ore zones or domains can be recognised and defined both from geology and sampling results. Once these domains are defined as a series of boundaries, they may be modelled as two dimensional grid surfaces or as wire-framed three dimensional geometries, depending on the complexity of the orebody. It is the definition of these domains which provides the sound geological basis for reserves computation. To estimate reserves it is necessary to determine both volume of ore and grade of ore. The ore volume is calculated within each domain as defined by the confining surfaces or wire-frames. The ore

Jan 1, 1987

By R. I. Yano

Analyses of trace elements in bulk ores and in chalcopyrite and other ore minerals from porphyry copper systems worldwide, including skarns and breccia pipes, reveal some key factors regarding byproduct critical elements. Petrographic and scanning electron microscope analyses combined with a laser ablation inductively coupled plasma mass spectrometry technique developed by the USGS on selected ores from the Mackay-Stanford Ore Deposits Collection suggest that selenium occurs as atomic substitutions in sulfides, particularly pyrrhotite (up to 430 ppm) and chalcopyrite (up to 300 ppm Se); tellurium occurs predominantly as less-than-five-micron-sized inclusions of bismuth-tellurium minerals in other ore minerals, particularly chalcopyrite; cobalt and nickel are locally enriched in pyrite (up to 7800 ppm Co and 9100 ppm Ni); gallium is locally enriched in magnetite (up to 83 ppm Ga); indium and silver are locally enriched in chalcopyrite (up to 890 ppm In and 770 ppm Ag); cadmium substitutes for zinc, particularly in sphalerite (up to 4100 ppm Cd). There is considerable variation, both between and within individual deposits, in both selenium and tellurium content in these copper ores, ranging from 0.6 to 148 ppm Se and 0.09 to 64 ppm Te. Indium tends to be high in copper ores that are also enriched in silver. At current prices, many of these elements are sufficiently enriched to warrant investigation into metallurgical recovery as byproducts of the major elements.

Feb 27, 2013

By F. W. Brackebusch

Paste backfill is a pumpable, flowable, non-Newtonian fluid consisting generally of mine tailings and cement. Paste is prepared from dilute slurries of tailings. This is done by dewatering the slurries with conventional thickening or filtering. Backfill with a paste consistency is prepared by mixing dewatered tailings with cement and water to obtain the desired consistency of medium slump concrete. The paste is pumped with concrete pumps over relatively long (1 km or 0.6 mile) horizontal distances. More commonly, though, it flows by gravity down a mine shaft and then horizontally to the void being filled. Alternatively, cement can be added near the end of the pipeline. A certain proportion of fine particles <20 µm (<625 mesh) must be present in pastes but particles of aggregate can be added without significantly affecting the flow characteristics. Detailed testwork is necessary to design a system to prepare and place paste backfill. Testwork must determine dewatering characteristics, strength of mixes and friction in pipelines. Plants must be well engineered and controlled with PLCs because high quality control is necessary to prevent plugged pipelines and excessive pressures. Relatively small amounts of cement (3% to 5%) produce stiff backfill material 1.5 to 3.5 MPa (217 to 507 psi). The advantages of paste backfill in a mining operation include reduced mine dewatering, labor and materials savings, reduced tailings impoundment requirements, good support properties and reduced spills underground. In certain cases where more than 30% of the weight of the ore is sold as a product, the entire tailings stream can be placed underground. Paste technology can he used for surface or underground placement of tailings.

Jan 1, 1995

By P. M. Fozzard

The Chaucha porphyry copper/molybdenum deposit was discovered by a United Nations team of geologists working with a ?counter- part" team of staff of the Ecuadorian government&apos;s General Directorate of Geology and Mines (DDGM) in July 1968. The exploration program formed the latter part of phase I work plan of a two-phased exploration project financed by the United Nations Development Programme and initiated in late 1964. The author was a team geologist during the period 1965-1967 and subsequently project manager for the period 1968-1972. The Chaucha property lies some 10 km (6 miles) east of the north- south-running western boundary of what was known as Operation Area No. 5. This area of some 10 500 km2(4050 sq miles) is a square truncated to the southeast and centered on the city of Cuenca, the major provincial capital (Azuay Province) of southern Ecuador. The eastern half of the exploration area is dominated by the Cretaceous- Tertiary sedimentary valley (basin) of Cuenca (Caar-Azuay) and its related drainage area. The western half, in which Chaucha lies, is dominated by the high Cordillera Occidental volcanic plateau and the western erosional valleys of the Andes draining to the Pacific. The valley that dominates the eastern part of the area [I500 m (4920 ft) above sea level] is transected by the Pan-American Highway. Because of increased agricultural activity associated with the Cuenca Valley, the area is reasonably well covered by a road network of varying quality. The high western area up to 4000 m (13,120 ft) in altitude is largely barren and completely inaccessible by vehicle. The geological reconnaissance map of the region is shown in Fig. 1.

Jan 1, 1991

By Robert F. Randolph, Arnold C. Love

This study describes the positioning strategies used by operators of radio controlled underground mining machines. The observations have implications for task design to insure adequate visibility and task performance. Radio controlled continuous coal mining machines have allowed many mines to increase safety and production by placing human operators away from the hazards of an unsupported mine roof. The operator is no longer confined to an operators component and visibility can be enhanced with proper positioning. Also, the operator is no longer subjected to the shocks and vibrations of the mining machine. The operator&apos;s ability to move freely about the worksite requires a careful analysis of several competing safety and production considerations. Thirty-five operators of remotely controlled continuous mining machines were observed using work sampling followed by interviews to determine where the operator was positioned and what he or she was watching. These observations were separated according to the task being performed by the continuous mining machine and summarized as position density plots. The specific task of tramming in reverse through a crosscut is analyzed along with more general summaries of the time miners spend outside of the policy-defined operating positions while performing other production tasks. The operators were: observed to frequently vary from company standard operating procedures (SOP). Many of the variations from company SOPS were based on task demands. Interview responses indicated that portions of the mining task place visibility demands on the operators that are difficult to accommodate within existing procedures. An improved task design process would include these visibility requirements. Also, the operator&apos;s vision can be augmented thorough video cameras in future teleoperated mining systems, and the operator can be increasingly isolated from environmental hazards.

Jan 1, 1992

By S. R. Wardwell, M. J. Robison

INTRODUCTION The first phase of the Los Angeles Metro Rail Project consists of 7.1 km of subway and stations running through downtown Los Angeles from Union Station to MacArthur Park. Contract A146, Tunnels from 5th/HILL Station to 7th/Flower Station, involves tunnel construction through the heart of downtown Los Angeles. The alignment of the tunnels passes beneath twelve buildings, ranging from a 3-story below grade parking structure to numerous 12 to 14 story buildings. The soil along the alignment is alluvium, consisting of silts and clays, clean sands and gravels located above the ground water table. Because of unstable ground conditions, which led to excessive ground losses in several instances, and because of the potential for excessive building settlements, it became necessary to design and perform a program of chemical grouting. The chemical grouting program was designed such that tunneling could proceed on a one shift per day basis, with chemical grounting being performed on the remaining two shifts. Each day 21,000 to 31,000 liters of sodium silicate grout were injected through sleeveport grout pipes installed 18 m deep through the tunnel face. Tunnel advance rates of 12 m per day, 60 m per week, under full chemical grout cover were achieved. The chemical grouting program virtually eliminated both ground loss and settlement and permitted successful excavation of the tunnels. The purpose of this paper is to describe the chemical grouting program used to control ground losses and settlement on Los Angeles Metro Rail Contract A146. The paper begins with a description of

Jan 1, 1991

By J. F. T. Agapito, R. R. Goodrich

Yield pillars have been used for many years to help reduce stresses near mine openings and improve roof and floor stability. A yield pillar is often defined as a pillar that fails but retains residual strength. Stress transfer occurs through the roof and floor after the peak strength of the pillar is reached. High stresses are transferred from around the openings onto abutments that can be barrier pillars or unmined ground. This mechanism, often referred to as pressure arching, is possible as long as the width of yield pillar mining (panel width) is less than the critical width above which stresses cannot be carried by the overburden. Significant stress transfer also can occur due to small amounts of pillar and/or floor yielding before the peak strength is reached. This is accomplished in a quasi-elastic manner with little or no visible roof and pillar fracturing or floor heave. Long-term stability may be achieved when stresses and mechanical properties are favorable to prefailure yielding. This paper gives practical examples where improvements in stability and resource recovery were achieved with this mechanism. Yielding was assessed by comparing measured and calculated vertical pillar stresses. Results indicated that calculated stresses in the pillars were 25% to 40% higher than the measured stresses, demonstrating significant arching load transfer to the abutments. Prefailure yielding is probably often present but unintentional in both development and production areas. Better recognition and use of this mechanism should lead to design improvements, as mines become deeper.

Jan 1, 2003

By J. W. Stevenson

The need for a separate ventilation department within the management team was recognized by the management of U. S. Pipe and Foundry before the company was purchased by Jim Walter Corporation in January, 1970. Because the coal beds of the deep underground coal properties owned by Jim Walter Resources lay 1300 to 2200 feet below the surface, efficient mine ventilation practices are essential through shaft openings varying from 16 to 22 feet in diameter. The extremely high methane gas quantity indicated to be in the coal bed because of the depth of cover and documented by various U. S. Bureau of Mines tests and demonstrated by early mining proved the need to implement this early management decision. At U. S. Pipe and Foundry mine ventilation was a function of the Mining Engineering Department with ventilation personnel assigned to the mine receiving their day to day work assignments from the mine manager or mine foreman. At Jim Walter Resources, the General Manager - Ventilation reports to the Senior Vice President, Mining Engineering, who reports directly to the President, Mining Division, Figure 1 (Company Organization Chart). Position descriptions are static; however positions are dynamic and consequently the degree of emphasis of specific duties and responsibilities change depending not only upon the aptitude of the individual performing the job but also upon his ability to meet the needs of his supervisors; and ultimately upon his ability to react to the economic forces directing our society. The following describes the duties and responsibilities of the General Manager - Ventilation, Figure 2.

Jan 1, 1980

By Samuel M. Cassidy

The exact date of man&apos;s first use of coal is lost in antiquity. The discovery that certain black rock would burn was undoubtedly accidental and probably occurred independently and many times in the world over thousands of years. It is quite likely that these independent discoveries were made when primitive man chanced to build camp fires on exposed ledges of a black rock, then was amazed when it caught fire. The Chinese recorded the use of coal 1100 years before the Christian Era and from the Bible we learn that King Solomon was familiar with coal in what is now Syria. In Wales, there .is evidence that the Bronze Age people used coal for funeral pyres, and it is known that the Romans used this fuel. There are other ancient references. So the knowledge that coal would burn, and even some uses of that knowledge, go back thousands of years. However, practical and consistent use of coal seems to date to England in the Middle Ages.

Jan 1, 1981

By S. G. Hardcastle, Akbar Sheikh

In Canadian underground uranium mines, bacterial leaching is being increasingly applied to low-grade ore reserves. At Denison Mines Limited uranium operations, old stopes are used as leaching vessels; these contain a leaching muck pile brought down by drilling and blasting from the back which contained a low-grade reef. The bacteria used require atmospheric oxygen to oxidize the pyritic ore. A study was initiated to evaluate the ventilation, including oxygen supply, specifically, of flood leaching stopes during their rest period. The method of ventilation investigated was a single ended compressed air system which feeds airlines laid under the muckpile and carried through the inlet pressure bulkhead. The air delivery system was tested for post- blast integrity with a sulphur hexafluoride, SF6, tracer gas technique. This was injected into the intake compressed air line and collected at the stope&apos;s borehole exhaust in grab-sampling bags. The samples were analyzed with a laboratory gas chromatograph and results provided information on the stope&apos;s airflow, average residence time, overall clearance time, volume of the airpath and the airflow distribution. The borehole exhaust was monitored by anemometer and psychrometer and indicated that the psychrometric conditions in the stope were independent of the area&apos;s ambient climate. Evaluation of the exhaust&apos;s standard gaseous composition showed the oxygen consumption of the bacteria to be independent of the investigated flow range. Field derived results are compared with computer models, theoretical predictions and laboratory investigations.

Jan 1, 1987

By I. H. Keith

INTRODUCTION The following papers describe the extraction of nickel in the form of ferronickel from the Dominican laterites. The Falconbridge process was developed initially in the Falconbridge Metallurgical Laboratories and subsequently in several successive stages of pilot plant operation in the Dominican Republic. In the course of this work we came to believe that there is advantage in piloting on site. Mining, metallurgical and geo-political considerations all have major impact and that belief has been borne out by commercial plant experience. Lateritic nickel ores differ substantially, even within the same orebody, in their amenability to extraction methods. The Falconbridge process takes account of the heterogeneous nature of the deposit. Three years of geological field exploration led to ten years of process development after it was realised that the then known metallurgical processes would not give economical extraction from the Dominican ores. In addition to establishing the viability of a novel pyrometallurgical approach, it was necessary to verify design parameters for a very considerable scale-up to prototype commercial operation. The plant was eventually constructed within the original estimates of time and cost. Unique features contributing to the technical and commercial success of the project are described. Additionally, some bold extrapolation based on pilot plant work, eventually proved to be quite conservative. The mine is not a conventional open pit operation, but is perhaps better characterised as an earth moving job. Novel application of mobile equipment led to great flexibility in the mine, where operation of several mining fronts is essential to maintaining uniformity of ore feed to the plant. The practical aspects of almost total acceptance of the oversize run-of-mine material through a high-capacity unit,

Jan 1, 1979

By S. Hardcastle

Kidd Creek mine has recently completed upgrades of its primary ventilation systems enabling it to maintain a delivery of 1200 m3/s to continue mining ore zones extending to over 3000 m below surface. Following these upgrades the mine initiated a multi-stage review of their ventilation usage. The focus of these reviews, ranged from a brainstorming session of invited experts, through an evaluation of production plans to a detailed analysis of production data to determine if the ventilation system could be run more efficiently, thereby reducing the mine?s power consumption and associated operating costs. The initial review identified 1500 kW of installed fan power that could be eliminated from the primary ventilation system. The benefits of the subsequent analyses, so far, are not as measurable. The second and third analyses, respectively using long range production plan data and historic production data to determine ventilation requirements based upon diesel equipment, did not agree. Both were shown to have limitations, the future based analysis underestimating, and the historical analysis overestimating the requirements. Regardless of the failings of each method, important outcomes were achieved from the detailed analyses, namely, the ability for a mine to meet a forward analysis prediction of airflow depends on its ability to adjust the ventilation to meet the dynamic nature of the mining process. Also, to minimize total ventilation requirements, a mine must regularly redistribute its airflow; this not only reduces the total volume requirement but also increases the variability of the delivered flows which can provide further operational savings. Since the detailed analyses, the Kidd Creek mine has implemented a more frequent ventilation review and redistribution procedure; consequently, it now operates with an average delivery of 930 m3/s, which is 23% lower than in 2005 at the start of the review process.

Jan 1, 2009

By S. J. Parkin, P. Shead

Extraction of coal at Harworth Colliery is undertaken in the Deep Soft seam at roughly 1000m depth where the strata temperature is 42 "C. Production employs the longwall retreating method using high powered mechanised methods to extract coal at a rate of approximately 40,000 tonnes per week from a single face. This paper describes the climatic conditions encountered on a typical district , 6&apos;s district, where the initial ventilation set-up was as a typical U-type district which was antitropally ventilated. Under this initial set-up climatic conditions in the intake typically exceeded 30 "C effective whilst in the face area and in the return airway effective temperatures in excess of 32 "C and 33 "C were common . The paper then proceeds to describe the methods employed to attempt to improve the climatic conditions on the district, especially with regard to the coal face and return airways and describes in detail the effects of reversing the district airflow direction, employing homotropal ventilation, on the climatic conditions. The results of this reversal have been dramatic and have resulted in a substantial improvement in the climatic conditions experienced , however problems have been encountered with the control of methane gas since the changeover. The final part of the paper describes the results of computer simulations to analyse the effect of various ventilation designs on the predicted climate for future production districts in order to de- fine a district layout which will produce acceptable climatic conditions in the working zone without the need to use refrigeration techniques and which will improve methane gas control .

Jan 1, 1997

By T. C. Rao, N. Suresh, M. Vanangamudi

Experiments have been conducted on a 76¬mm water-only cyclone treating cowl below 2 mm size having different proportion of -0.075 mm fines. The effect of cone angle of the cyclone (compound cone) has been analyzed on water split, separation of -0.075 mm fines, separation of coarse solids, and on separation behavior of individual size ructions of the feed. It has been noted from the results that there exists a linear relationship between the flow rate of water in the feed and flow rate of water reporting to overflow stream. This relationship is independent of the cone angle and, with changes in the fines content in the feed, only the intercept of the straight varies, keeping the slope constant. Further, it has also been found that the percentage of fines below 0.075 mm reporting to the overflow is directly proportional to the percentage of feed wafer reporting to the overflow. This relationship is found to be independent of the cone angle and the fines in the feed. The performance of the water-only cyclone has been analyzed by plotting partition curves for different experimental conditions. In addition to this, the Rosin-Rammler equation has been fitted to the partition curves of the hulk feed and individual size-fractions. Tile analysis of the results has revealed that the specific gravity of separation increases with increase in the cone angle of the cyclone while it decreases with increase in percent fines present in the feed. Mathematical relationships have been developed to relate the variation in SG50 with cone angle and percent fines in the feed.

Jan 1, 1990

By R. C. Shodde, R. D. La Nauze

Major societal and industry changes over the last four decades have influenced the management of technology in the minerals industry. From the authors&apos; experiences in both private and public sector R&D, the paper analyzes the range of strategic and structural changes and provides examples of some key technology delivery responses. For those charged with managing technology, the two key challenges facing them over the next decade are (I) moving technology development from a cost focus to a value focus (that is, from "how much long-term research can we afford?" to "identifying and capturing the value created from R&D”) and (2) the recruitment and retention of key talent. THE NEED TO ADAPT "Change is slow and gradual. It requires hard work, a bit of luck, a fair amount of self- sacrifice, and a lot of patience (Greene 1998)." Since the 1960s the world has changed and the minerals industry has had to adapt to the changing circumstances. In the &apos;60s, minerals were there to be discovered and fortunes to be made; in Australia, the World War I1 embargo on exporting iron ore was lifted and the Western Australian iron-ore boom commenced, to be followed by the exploitation of the Darling Range bauxites; copper, lead, zinc and nickel were discovered and mines developed. The Australian dollar was worth US$1.11 whereas today it is around US$0.65. The oil crisis of 1976 sharpened focus on the sensitivity of the minerals industry on energy costs. By the late 1970s The Club of Rome was predicting the imminent demise of certain key metals-a prediction that has not been fulfilled-though the signs of the shift

Jan 1, 2004