Search Documents

By Nancy C. Shaver, Alan Tapp

Leach pads of 272,000 tonnes (300,000 st) and 910,000 tonnes (1,000,000 st) with associated operating ponds have recently been constructed on sidehill locations with up to 20 percent slopes. The larger pad was designed in anticipation of ore heights up to 30 meters (100 feet). This paper describes site investigations and civil engineering design as well as construction experience associated with development of these pads. The leach pads were underlain by a double liner system consisting of 2 mm (80- mil) HDPE over compacted fine-grained tailings, with an intermediate leak detection layer. Both sand and geotextile drainage layers were used. Pad slopes were limited by the factor of safety against sliding on the HDPE liner. The sites for the facilities had been substantially disturbed by prior mining and construction activities. Natural conditions included peat layers and locally swampy ground. Site preparation included french drains to lower the water table and stripping of unsuitable subgrade materials.

Jan 1, 1987

By P. M. Sandgren, H. Al-Dabbagh

Saudi Company for Precious Metals (SCPM) is jointly owned by the Saudi Arabian state organization Petromin (The General Petroleium & Mineral Organization) and Boliden of Sweden. The company operates the Sukhaybarat gold mine in the Saudi Arabian desert and produces some 80,000 ounces of gold per year by agitation and heap leaching. The discovery, development, and operation of this mine is a success story. After the first drill hole intercepted a gold mineralization in 1983, it took the partners only 8 years to delineate the ore reserve, locate water sources, prepare pre-and final feasibility studies, obtain permits, design, and construct the facilities. Sukhaybarat, which is an open pit mine, started off with a carbon-in-leach agitation plant only, but a heap leach facility was added in the beginning of 1995. Since start of operation in the middle of 1991, a total of 300,000 ounces of gold has been produced in the first four years of operation at a very competitive cost.

Jan 1, 1996

By P. Pal Roy, Ajit Raj Ostwal, M. M. Singh

Field investigations have revealed that sawdust can be used as an efficient additive to ANFO for carrying out production blasts in limestone mines. Sawdust can be used at a reasonably reduced cost without sacrificing fragmentation, muck profile and wall control. Such additives lower the detonation pressure of ANFO by acting as low-grade fuel that reacts or burns more slowly in the presence of ammonium nitrate than does fuel oil. On detonation, it eventually forms near-ideal oxygen balance that helps in liberating maximum energy to break the surrounding rock. It also forms a low-density stable mixture that helps in reducing loading density (kg/m) of explosive in the blasthole. Experiments performed at the Hirmi Limestone mine, M/s L&T, and at the Lambasta Limestone mine, M/s Jaypee Rewa Cements, showed the novel acceptance of the technique in a highly competitive market where cost reduction has been a major area of thrust.

Jan 1, 2003

By Donald L. Bott

A computer model called the Quality Compliance Model was developed to optimize the mine planning and sequencing in area coal mining with respect to the limit on pounds of sulfur dioxide per million BTU imposed by regulations. The objective of the model is to maximize the amount of high sulfur coal mined from various benches while meeting the specified compl'ance standards. Given multiple seams and multiple benching operations, the mining sequence from each pit is simulated. The rate of mining is controlled such that the in-pit blending will maximize the usage of high sulfur coal and meet compliance standards. The compliant coal can be stockpiled for usage at a later date, or it can be disassociated. This calculation can be based on any given rate of production, i.e., from as small a unit as a unit train to as large as monthly or yearly production.

Jan 1, 1982

By C. J. Pritchard

I commend the authors on examining an interesting method of shaft lining and attempting to improve safety in a dangerous environment by remotely installing the shaft lining. It is important, though, to not trade off shaft lining safety for long-term mine safety by lining an intake shaft with combustible material. In many operations, the mine utilities are installed next to the lining of the intake shaft, supplying a possible ignition source if damaged or overloaded. Although the polyurethane studied in the paper is of relatively high density, no mention is made of the flame retardency of the samples. When exposed to heat, small amounts of polyure¬thane will melt and bum but are extinguished when the heat source is removed. If large surface areas of combustible polyurethane - a tunnel or mine shaft - are exposed to ignition heat sources that are not removed or extinguished early, an uncontrollable, fuel rich fire may result with high carbon monoxide levels, low oxygen concentrations, and greatly increased burning rates that can have devastating effects on the ventilation system and miners' safety.

Jan 1, 1990

By R. R. Beebe

When an economic mineral deposit is first discovered, it is almost immediately defined in terms of tonnage and grade. As exploration and assessment continue, the initial definition is ordinarily qualified by such terms as "proven," "probable" and so on. Even at this stage, the fundamental philosophies of the discoverers may manifest themselves in conservative or optimistic views of the deposit's potential. It is unusual, however, for the philosophies to be expressed in terms of metallurgical performance criteria at such an early stage unless the ore is very unusual in its chemistry or mineralogy. Even before drilling is completed, the first mining plans appear, with or without the benefit of metallurgical test data. This is the point at which management philosophies can have some of their greatest impacts. In ideal cases, where large, uniform ore bodies can be developed and mined according to assay cutoffs, the conventional philosophy of maximizing tonnage while minimizing cost can be followed without much metallurgical difficulty. Unfortunately, such cases are rather uncommon. Even large, low-grade

Jan 1, 1991

By Wojciech Suwala

The transition from centrally planned to market economy affects methods of economic analysis. The models which were used in the past are riot valid presently, however they we're the seed which initialized the development of methods and applications. There is more than twenty years of experience in modeling of coal mining development. The first attempts were devoted to select the moment of mine construction commencement in order to meet planned output. In Poland significant development of such models began in 1986. Within the Central Research and Development Program there has been a continuous development of models. These models from econometric to optimization ones, were a certain sequence which, in accordance with changing economy system, led to the last version of the model. It is the most suitable one for contemporary problems of coal mining in present Polish circumstances.

Jan 1, 1992

By J. L. Hendrix, M. Ahmadiantehrani, G. Ramadorai

The concept of hypochlorite treatment prior to cyanidation in the heap leaching of low grade carbonaceous gold ores is discussed. Laboratory column leach tests using a low grade carbonaceous ore were performed to investigate the effects of pH, hypochlorite consumption and concentration, and bed height on total gold extraction. At high pH, hypochlorite stability increases and thus, hypochlorite consumption decreases. At room temperature, total gold extraction is proportional to hypochlorite consumption. However, at some point additional hypochlorite consumption does not increase gold extraction. Gold recoveries of 10% and 80% are achieved at 12 and 167 lb/ton hypochlorite consumption, respectively. Increasing hypochlorite concentration increases the rate of extraction. For a given hypochlorite consumption, gold extraction increased with decreasing ore bed height. Finally, using calcium hypochlorite results in higher gold extraction than using sodium hypochlorite at a fixed hypochlorite consumption.

Jan 1, 1992

By S. M. Hsiung, Wen H. Su, Syd S. Peng

This paper examines the interaction problems of multiple seam mining by combining underground investigation, laboratory testings, and numerical modeling. One case of multiple seam interaction that occurred recently in West Virginia was carefully studied. Causes for the interaction problems were identified and the corresponding mining recommendations were proposed. The principle of pillar columnization and the effect of a remnant pillar on mining operations in the underlying and over- lying seams were also carefully examined. Considerable attention was given to the effect the pillar size, the pillar width, the coal stiffness, the extraction ratio, the degree of inhomogeneity in the interburden, the overburden thickness, the mechanical properties of the interburden rocks, the strata inclination, the interburden thickness, and the in-situ horizontal stresses have on the pillar load transfer mechanism.

Jan 1, 1986

By D. A. Stanley, B. J. Scheiner

The U.S. Bureau of Mines has thoroughly investigated the flocculation of phosphatic clay waste with polyethylene oxide (PEO). The studies included both theoretical and applied aspects of the flocculation sequence. The screen dewatering technique developed by the Bureau was field tested at four different Florida phosphate mines. The results of these field studies are presented. Also, to determine the mechanisms of the interaction of PEO with montmorillonite clays common to the phosphatic clay waste, a number of theoretical studies were conducted. An empirical equation was developed to describe the amount of PEO needed for flocculation. Infrared, ion exchange, and rheology techniques were used to study the interaction of PEO with Florida clays. The results of these studies are also presented.

Jan 1, 1993

By Justus B. Deen

Given that the majority of mine ventilation operating costs are imposed by shafts, the need to predict the resistance of a planned shaft with reasonable accuracy is important. During conceptual design, shaft resistances are usually predicted by use of published friction factors, k, based upon lining and fitting configurations. More often than not, published friction factors do not directly coincide with "real" shafts, so their use is somewhat limited. For more accurate shaft resistance determination, equations both theoretical and empirical may be employed if there is detailed knowledge of the shaft. These equations treat the shaft resistance as discrete components, with their sum being the overall shaft resistance. This paper describes the basic shaft resistance equations and verifies these equations by comparison to field measured shaft resistances. Several shafts were examined which varied in depth, shape and fitting arrangements. Results are presented and conclusions drawn to show that the shaft resistance equations are accurate.

Jan 1, 1991

By Abdullah Arik

An ore reserve block model is the basis for various decisions in mine development and production. The block model is initially built using the information from the drillhole data only. Once the mine is put in operation, the information from the blasthole data becomes available. Since the spacing of the blastholes are much closer than the exploration drillholes, the blasthole data gathered from the mine over the years become quite extensive containing valuable information about the deposit. In practice, the information from the blastholes is the basis of determining the ore and waste boundaries between and within mining blocks. In an ore reserve model, the valuation of blocks on and close to the pit face can obviously be improved by using blasthole data from neat by drilled and mined-out blocks in addition to using the widely spaced drillhole data. The ideal basis on which to integrate blasthole and drillhole data is to use cokriging.

Jan 1, 1996

By Shuji Owada, Keisuke Yasukawa

Electrostatic and/or high tension separation has been used for the separation of rare metal bearing minerals, foods, industrial wastes and so on. Since the separation is achieved by the difference mainly in surface conductivity of particles, the efficiency in humid circumstances is very low, and then, the applicability is considerably limited. We applied the following two-stage pretreatment technique to the separation process, which involves (1) adjustment of surface wettability by adsorbing surfactant on the particle surface and (2) control of the surface conductivity by spraying with electrolyte aqueous solution. The addition of this pretreatment technique has been found to have a great advantage over conventional methods. Separation efficiency is achieved even in humid circumstances and selectivity can also be obtained between insulator minerals. The selectivity is very similar to that of flotation in wet process. This separation technique will be applied not only to mineral processing but the processing of industrial waste such as electric and electronic waste materials.

Jan 1, 1995

By Michael P. Foose

In 1994, more than 41 of the approximately 160 coal-fired, electrical- power plants within the six-state Ohio River Valley region used flue-gas desulfurization (FGD) units to desulfurize their emissions, an approximately 100% increase over the number of plants using FGD units in 1989. This increase represents a trend that may continue with greater efforts to meet Federal Clean Air Act standards. Abundant limestone resources exist in the Ohio River Valley and are accessed by approximately 975 quarries. However, only 35 of these are believed to have supplied limestone for FGD electrical generating facilities. The locations of these limestone suppliers do not show a simple spatial correlation with FGD facilities, and the closest quarries are not being used in most cases. Thus, reduction in transportation costs may be possible in some cases. Most waste generated by FGD electrical-generating plants is not recycled. However, many FGD sites are relatively close to gypsum wallboard producers that may be able to process some of their waste.

Jan 1, 1999

By Fathi Habashi

SELENIUM AND tellurium are by-products of electrolytic copper refining. Copper anodes contain 0.01-0.2 % Se and up to 0.04 % Te; during electrolysis these deposit as a slime at the bottom of the cell. Such slimes contain 2-15% Se and 0.5-8 % Te, as selenides and tellurides of gold, silver, and copper. The following compounds have been identified in the slimes: (Ag, Au)Te2, Ag2Se, Ag2Te, CuAgSe, Cu2Se, Cu2Te. Anodic slimes from copper electro¬lytic refining are a grayish black powder, minus 200 mesh. When this complex mixture is decomposed in an acid medium, elemental selenium and tellurium can be obtained, while in an alkaline medium, both metals go into solution. Acid leaching The slime is charged in acid digesters of 800-900 lb capacity, heated to 260°C with 78 % H2SO4, for 8-12 hr. During digestion the following reactions take place:

Jan 1, 1970

By Bruce T. Stanley

Though most porphyry-molybdenum deposits lend themselves to various reserve estimating techniques, still there must exist the constant effort to not merely obtain an estimate but rather to obtain the best estimate. To answer the challenge of a complete ore reserve estimation, one must attack the problem with the purpose of obtaining the results closest to reality. What we wish to determine is simple: metric tons (short tons), grade, and kilograms (pounds) of molybdenum contained. In order to effectively accomplish this task, further consideration must be given to the ease of using the information obtained and its inherent reliability. The only known method for ore reserve estimation that supplies the needed results along with its distribution and a measure of confidence provided by sound mathematical backup is geostatistics. The following review is an example of geostatistical application of an ore reserve estimate at the AMAX Henderson mine demonstrating technique, viability, and usefulness of results.

Jan 1, 1979

By Gordon I. McPhail, John D. Nelson

Tailings management represents a major portion of the cost associated with extraction of gold. For each gram of gold extracted, 150 to 200 kg of waste material is produced. Because of environmental concerns and unwillingness of society to accept environmental damage caused by poor waste management practices it has become essential to follow responsible and safe practices in tailings management. This paper presents general aspects of tailings management and discusses different techniques utilized. Characteristics of tailings and the effects that these have on stability and environmental aspects are discussed. The paper also discusses the effect of mine back-filling practices on the surface disposal of the remaining tailings fraction.

Jan 1, 1987

By Keith G. Wallace, Malcolm J. McPherson

In order to model accurately a mine ventilation system in an existing mine, it is necessary to determine the resistance to airflow in all main airways. This is accomplished by measuring the airflow and pressure differential in each airway. Gauge and tube methods have been used to determine pressure drops in ramps and level airways. However, it has rarely been used in evaluating the frictional pressure drop in shafts. Because shafts commonly have the highest pressure loss in mines, it is critical that the resistance of these airways be determined accurately. This paper describes the theory and practice of using the gauge and tube method for determining the pressure drop in shafts. The pros and cons of using this method are discussed as well as a comparison between the gauge and tube and barometer measurement techniques. Case studies showing the accuracy of shaft gauge and tube measurements are also presented.

Jan 1, 1991

By Yelloji M. K. Rao, P. Somasundaran

Reagents of biological origin are becoming more and more important in the field of metallurgy, especially in the areas of mineral processing and hydrometallurgy. The advantage of lower operating cost over physical and chemical processes and the capacity to operate with low grade ores make the microbial processes further attractive. In this paper, the role of microbes directly as a reagent and microbially produced reagents or secreted metabolites in mineral processing and hydrometallurgy will be discussed. Adhesion of microbes to surfaces is known to alter the hydrophobicity of minerals. Applications include surface modification to impart hydrophobicity or hydrophilicity on sulfide or non-sulfide minerals and dissolution of precious metals. Microbes can also perform the role of flocculating agents. Biosorption of toxic and heavy metal ions by microbes are finding application in treating tailing ponds. Mechanisms associated with the use for microbially produced reagents are discussed along with some recent results.

Jan 1, 1994

By Louis W. Cope

INTRODUCTION Various methods for sampling placer deposits have been mentioned by Wojcik in Chapter 2. Here, a brief description and comparison of these methods will be given as related to bulk versus drill sampling. The advantages and disadvantages inherent to each will also be given. The means of sampling can be grouped into bulk or drill samples. As a generality, drill samples over a five-foot length will run from I/,, to 1 /, cubic yard, depending on the diameter of the drive shoe on the drill casing. Bulk samples can be expected to be in the range from one to many cubic yards each. SAMPLE METHODS Bulk Bulldozer-dug trenches and dozer or front-end loader pits are two methods to excavate large bulk samples. Smaller bulk samples can be obtained by digging small dimension shafts through the deposit, by hand or caisson-like drills. It is not recommended to split samples by alternate bucket-loads or by other means, as the effect of a nugget falling into one or the other fraction will seriously alter the sample.

Jan 1, 1992