Search Documents

By M. J. Virnig, C. P. J. Van Vuuren, A. J. Botha

The Zadra, AARL and organic elution processes and variations of them are presently widely used to recover gold from activated carbon. Despite this the study of the kinetics of elution have received relatively little attention. It is the aim of this study to investigate the rate processes taking place during elution in both inorganic and organic solutions. Batch adsorption and elution rate and equilibrium experiments were performed. The spatial concentration of gold inside carbon particles at various stages of the adsorption and elution processes were measured with a scanning electron microscope using an image analyzer to control and manage the micro-analysis data. The activated carbon particles exhibited film and intra-particle mass transfer rate- controlled behaviour during adsorption in a caustic aqueous solution at 95°C. Elutions in the aqueous caustic acetone solution at 30°C and the caustic aqueous solution at 95°C were unaffected by change in stirring rate. Elution was modelled by desorption reaction rate-control at the outer surface of the carbon particle. Adsorption and elution isotherms under duplicated solution conditions showed reasonable agreement for the inorganic solution and a large disparity for the organic solution.

Jan 1, 1993

By Salt Lake City Research Center, D. G. Foot, J. D. McKay

As part of its research program on column flotation, the Bureau of Mines, Salt Lake City Research Center has performed studies on (1) column flotation amenability and comparison with conventional flotation results for over 15 mineral systems, (2) alternative methods for improving column bubble generation systems, (3) mineral behavior within a column, and (4) the effect of changes in column operating parameters on flotation grade and recovery. Based on results from these studies, flotation columns (1) are capable of producing higher grade concentrates in fewer stages than conventional flotation cells at equivalent or increased recoveries, (2) require less retention time than conventional flotation cells, and (3) can be divided into cleaning and collection zones that have characteristic mineral-upgrading-per-foot values. Attempts to improve the column air sparger have led to the development of a superior external bubble generation system, which can (1) achieve increased air holdups. (2) produce bubbles from 400 Um to 4,000 Um average bubble diameter with minimal frother addition, (3) provide superior bubble size control, and (4) be maintained without column shutdown. Efforts are continuing to improve column flotation and transfer successful technology to industry.

Jan 1, 1988

By T. T. Chen, J. L. Jambor, J. E. Dutrizac

A reconnaissance study of the neutralization potential of 30 diverse minerals, 28 of which are silicates and aluminosilicates, has shown that most of these minerals contribute minimally to the neutralization potential (NP) in standard static tests. Feldspars in particular give low NP values and would not be expected to attenuate the acidity to any significant extent in acid rock drainage settings. The BET-determined surface areas of the minerals vary considerably, and the large surface areas of some of the pulverized samples have clearly affected the NP values even though the standard static-test protocol was used for the preparation of the samples. The low NP values of most silicates and aluminosilicates are in general agreement with the laboratory-determined slow dissolution rates for these minerals. The results suggest that, in the prediction of whether rocks will be acid-producing, the most realistic measure is that of the carbonate content. In mine wastes from metalliferous ore deposits, the contribution to the NP by the non-carbonate gangue assemblage is unlikely to be more than a token amount until well after the establishment of an acid rock drainage situation.

Jan 1, 2000

By P. Ollivier

The ore-processing plant of the Soremib mine Pour a (Burkina Faso) has now been in uninterrupted operation for 3 years. Ores from the oxidized and non-oxidized zones of the deposit are processed together in one flotation unit. About 60% of the gold is free and is recovered in a gravity processing unit. The residual gold in the flotation concentrate is processed on the spot by cyanidation and carbon-in-pulp.

Jan 1, 1998

By I. S. Parrish

Reserve audits have increased in recent years as more companies, especially juniors, enter the ranks of producers. Corporate and individual investors are seeking corroboration of stated reserves. The reserve audit satisfies this need. An audit assures investors that the reserves, as presented, are a reasonable and accurate approximation of the quantity and grade of the economically viable material present. The reserve audit verifies that there are no fundamental errors in logic, style or the data base, and that the reserves, as given, may be used for mine planning or economic forecasting. Reserves that pass an audit may be used with confidence in preparing cash flow projections and in deriving net present value or internal rate of return on any given project. This article describes what a consultant does while performing the reserve audit. In performing an audit there are four general areas of concern that must be checked: definitions, parameters, data and procedures. In each of these, the auditor must convince himself that the reserve study has complied with governmental regulations and guidelines, professional standards and industrial practices. Any deviation from these norms must be identified and its effect upon the appropriateness of the reserves evaluated. By concluding that a reserve study passes his audit, the reviewer is stating that there are no fundamental errors in logic or style and that spot checks have revealed no substantive errors in procedure or mechanics. The responsibility for the reserves remains with the entity that compiled the original study.

Jan 1, 1990

By J. M. Dean, R. L. Grayson, N. P. Reddy, Y. J. Wang

This 1988 survey provided a cross section of computer software use by the US coal industry. From 1250 mailed questionnaires, 171 responses were received, representing a 4.9% sampling of the 3496 US coal mines. Since the distribution of responses by regional stratum matched well with the distribution of mines by stratum, the survey was given statistical validity. A statistical description details the computer use by region, mining type, organizational size, the level of application within the organization, the type of software application used, the variety of computers on which the software was used and the percent of users within engineering, management and general applications categories. Overall, 63.5% of the respondents use computers at some level in their organizations. All of the mines producing more than 454 kt/a (500,000 stpy) used computers. However, for those producing more than 9 kt/a (10,000 stpy) but less than 91 kt/a (100,000stpy), only 44% used computers. Generally, the software applications were still data-processing oriented. The application sophistication grew with increasing mine size. Computer system models and configurations for different sized organizations are recommended based on the configurations used in the industry at the time of the survey.

Jan 1, 1994

By Tommy B. Thompson

The Cripple Creek diatreme-intrusive complex is known primarily for its vein telluride-gold ores. It is also known for the great vertical range of its major veins - >990 m (>3250 ft). Not as well-documented, however, are the ores dispersed into the wallrocks adjacent to veins, the ores associated with hydrothermal and tectonic breccias, or mineralized zones within fluvial, lacustrine and volcaniclastic rocks de- posited within the diatreme complex. The ore-gangue minerals were precipitated from oxidized, alkaline fluids that yielded an abundance of carbonate, sulfate and oxide minerals along with minor base metal sulfides and precious metal tellurides. Wallrock alteration is limited adjacent to veins and is more extensive within hydrothermal and tectonic breccias. Cripple Creek background The Cripple Creek district has a spectacular production history. More than 653 t (21 million oz) of gold were recovered between 1891 and 1959. Early published accounts documented the principal production from narrow- sheeted vein systems (Cross and Penrose, 1895; Lindgren and Ransome, 1906; Loughlin, 1927; Loughlin and Koschmann, 1935). Production also came from spectacular open-space fillings within the Cresson diatreme, also known as the Cresson “blow-out” (Patton, 1917; Patton and Wolf, 1915). Beginning in the mid- l96Os, more modern studies were initiated by the US Geological Survey (USGS) (Gott et al. , 1967, 1969; Kleinkopf et al., 1970) and by universities (Lane, 1976: Dwelley, 1984; Trippel, 1985; Thompson et al., 1985; Saunders, 1986; Birmingham, 1987; Eriksson, 1987; Nelson, 1989; Wood, 1990; Seibel, 1991).

Jan 1, 1992

By S. Mathur

The southern Florida phosphate deposits that will be mined in the future contain significant amounts of dolomite. Because high MgO levels are undesirable in phosphoric acid production, several flotation schemes for the removal of the dolomite have been attempted. Alternatively, selective flocculation has been suggested as a potential process. A high MgO rock was simulated with a 30:10:60 mixture of apatite, dolomite and silica, respectively. Single mineral selectivity was observed in the apatite-silica and dolomite- silica systems using Polyacrylic acid (PAA) and Poly(ethylene oxide) (PEO) flocculants, respectively. However, no single mineral selectivity was observed in the apatite-dolomite system using PEO. Heteroflocculation, suspected to be the major reason for the loss of selectivity, was minimized by the addition of a site blocking agent (SBA), consisting of a lower- molecular-weight fraction of PEO. Process parameters such as size reduction schemes, flocculant/SBA dosage and pH were investigated to achieve the desired separation. The selectivity obtained in binary mixed-mineral tests was also achieved in the ternary mixed-mineral system, namely, the apatite-dolomite-silica system. In this report, surface chemical characterization of the samples and their flocculation behavior are discussed.

Jan 1, 1995

By J. J. K. Daemen, C. Fairhurst

Two aspects of tunnel support design are considered, and for both particular attention is paid to the influence of rock failure around the tunnel on the loads developed on the supports. 1) In general it has not been possible to extend analytical methods for the study of rock failure around tunnels to three dimensions. As a consequence it was not possible to calculate either the influence of the face or the actual sequence of support loading as the face advanced. The finite element method made this extension possible. A simplified analysis of the influence of the face and of the sequence of support installation has been made. The influence of the original stress field and of the rock behaviour on the length of tunnel which can be left unsupported (related to the stand-up time) is shown. The degree to which a 2-dimensional analysis can be used to approximate the final support load is shown to be dependent upon the post-failure behaviour of the rock. 2) Tunnel support design requires a knowledge of the forces and of the -rock displacements which cause stressing and deformation of the support system. A 2-dimensional model incorporating a detailed representation of several support systems, of the rock behaviour in the broken zone and of the interaction between rock and support is given. The model allows the calculation of the stress distribution in the support. The significance of the relative stiffness of support and rock on the stresses developed in the support is shown.

Jan 1, 1997

By Victoria Vaccarezza, Corby Anderson

The demand for rare earth elements for everyday technology and applications has initiated much research into the extraction and recovery of these rare earth elements. An otherwise unknown group of minerals, eudialyte is a zircon silicate consisting of rare earth oxides (REO), contained in a unique mineral structure and represented by a complex chemical formula. Research into extraction and recovery of rare earth elements involves various beneficiation and hydrometallurgical techniques. The goal of beneficiation being to efficiently liberate and upgrade the REO content, followed by hydrometallurgy to extract the desired elements. This overview will discuss previous research on treating eudialyte group minerals via different mineral processing and extraction techniques.

By Balesh W. Konda, Andrew B. Cecala

Face ignitions occurring during longwall mining are increasing each year and are expected to continue to increase as deeper and gassier seams are mined. Effective methane monitoring strategies are needed to supplement techniques developed either to control the ignition sources or to dilute the gas to an acceptable concentration. Present monitoring strategies do not always detect dangerous concentrations as rapidly as they should. In a number of instances, dangerous concentrations have been observed at the shearer, but are diluted to acceptable levels when measured at the tailgate monitoring location. To effectively monitor and control methane concentrations, methane liberation and emission patterns must be identified. This need has led to a joint research effort between the Canada Centre for Mineral and Energy Technology and the United States Bureau of Mines. By combining the knowledge and experience of both organizations, the methane hazard facing underground longwall operations can be addressed more effectively. A comprehensive plan was developed to monitor methane levels throughout the panel and for an entire longwall mining cycle. In June-July 1986, a case study was performed at the Cape Breton Development Corporation's Lingan colliery in Sydney, Nova Scotia. This initial study was performed on two advancing longwall panels. Methane concentrations and flow patterns from this study are described in this report. A similar study is planned on a retreating longwall panel.

Jan 1, 1987

By Mark S. Stagg, Michael J. Nutting, Douglas R. Barlet

Single-row bench blasts at a reduced scale in the field were used to study the effects of delay time on fragmentation. Nine shots with a spacing of 21 in. and a burden of 15 in. (S/B = 1.4) and nine shots with a spacing of 30 in. and a burden of 15 in. (S/B = 2.0) were completely screened to determine particle size distributions. Delay intervals between holes ranged from 0 to 45 msec, corresponding to effective delay intervals ranging from 0 to 36 msec per foot of burden. Each shot was instrumented with strain and pressure gages to measure in situ blast dynamics and to evaluate interactions between blastholes. Finer overall fragmentation was produced for shots with delay intervals between 1 and 17 msec per foot of burden. Only for shots within this optimum delay range was it observed that the strains induced by stress waves constructively interacted with strains induced by gas pres- sure from an earlier detonated hole. Coarsest fragmentation resulted at delay intervals less than 1 msec/ft, where stress waves from each hole were observed to interact destructively, and at delay intervals greater than 24 msec/ft, where no inter- action between holes was observed, indicating a condition that can be considered as the firing of single hole shots independently.

Jan 1, 1986

By S. C. Suboleski

Underground long-range planning and mine design is an iterative process beginning with a specified production level, quality criteria, and geology of the deposit. Given these factors, face equipment is selected, the number of units needed and production per unit are calculated, and the mine infrastructure needs are developed. The scheduling of units then follows, with the design of the various support systems coming next. The support systems needed to maintain production can be grouped as follows: (1) outby haulage of mined material, (2) supply and manpower haulage, (3) ventilation and associated environmental considerations, (4) drainage, fresh water, and related considerations, (5) rock mechanics, and (6) power, supply. Thus, long-range planning may be viewed as a three-tiered structure, with the data on required production, product quality, and geology at the upper level; the development of face production capacity and the scheduling of units sufficient to meet the needs of the first two at the second level; and the development of support operations for the production units at the third level. Changes at any level may affect not only the items on that tier but may also cause a change to the items on the tier above and below. For example, if the rock mechanics data indicate that desired opening sizes will not be stable, then this situation will affect not only the ventilation design but also the production rate and possibly the selection of equipment itself. These, in turn, may affect the scheduling of units and the number of units, ultimately influencing the entire third tier of systems.

Jan 1, 1979

By M. S. Basich, J. S. Scope1, J. H. Raeder

During 1983, The Youghiogheny and Ohio Coal Company's lost-time-incidence rate was 8.1, equal to the average for underground bituminous operators. How- ever, one half of all lost-time injuries were low back, back and neck related. In reviewing these results, we determined that substantial improvement could be made. We investigated existing back schools and the possibility of opening an in-house clinic. In September 1984, we began The Youghiogheny and Ohio Coal Company's Back Care Program. The objectives of the program are to reduce the number of back injuries incurred at the work site, hasten recovery time, decrease medical and workers' compensation costs and provide the employee with a thorough understanding of his problem. A state-of-the-art clinic capable of treating injuries to the spine and extremities has been established at the work site. The clinic is staffed by a licensed physical therapist and is offered to all employees on a voluntary basis under physician referral. The approach to treatment is multi-phasic. For the typical patient, the initial goal is to reduce pain and correct dysfunction. Treatment modalities such as auto-traction, extension exercises, ultra sound and moist heat are frequently used. During this period the patient is given extensive education regarding his problem. As soon as more vigorous activity can be tolerated, a work-hardening pro- gram consisting of job simulation activities designed to improve flexibility, strength and functional capability is begun.

Jan 1, 1986

By Don U. Deere, Edward J. Cording

INTRODUCTION Observations during construction form an integral part of the design and construction of major underground works. Observations as used herein include visual inspection, detailed geologic mapping, and correlation of geology with support conditions, as well as instrumentation to provide more precise information regarding rock movements and support load. This paper describes the application of an observational program to one of the more difficult design and construction problems underground -- the excavation and support of large chambers at shallow depth in rock of variable quality. Emphasis on underground construction for subways and utilities in urban areas is bringing this problem to increased prominence. It is our intent to focus on the design and construction problems associated with such excavations and to describe observational methods which can be employed to aid in their construction. Observational programs may serve two purposes. One is to monitor the rock and support conditions in order to provide early warning of potential construction problems. Such a program should be routinely used in critical locations on major underground excavations of the type described in this paper. The program should be closely coordinated with the inspection effort and construction control. The other purpose is to provide detailed information regarding the interaction of support conditions and rock displacements to aid in development of more efficient design and construction procedures on later projects. For this purpose, instrumentation might be concentrated in special test sections where specific and typical

Jan 1, 1997

By J. Hanna, H. R. Gonzalez

Discussion by N.L. Hargett Dear Dr. Hanna: As discussed in our phone conversation, we are enclosing a suggested revision to the paper, "Application of Bentonitic Clays in Suspension Fertilizer Formulations," published in MINERAL & METALLURGICAL PROCESSING, May 1990. The revision will replace the second paragraph in the article. The reason for the revision is that suspensions have decreased in market share since 1984 and at present comprise an estimated 25% to 30% of fluid mixtures. This represents 6% to 7% of all fluids and only 2% to 3% percent of all fertilizers. Based on national surveys conducted by the Association of American Plant Food Control Officials (AAPFCO), suspensions comprised an estimated 25% of all fluid mixtures in 1974, 33% in 1976, 35% in 1980, 40% in 1984, and 36% in 1988. Revision to "Application of Bentonitic Clays in Suspension Fertilizer Formulations." Suspension fertilizers are an important segment of the fertilizer industry in the United States. Suspensions allow higher concentrations of nutrients (N, P2O5, K2O) than clear liquid solution fertilizers. K20 content of solutions is limited to about 10%, while suspensions can contain more than 30% K2O. Suspensions can tolerate greater variations in temperature than solutions. In suspensions, if crystallization occurs, the crystals can remain suspended in a clay jell instead of settling as they would in solutions. Solubility is not a limiting factor in suspensions, since complete solubility of phosphate is not required. This allows a wider range of phosphate materials to be used. Also, materials commonly used in formulating suspensions are less expensive and more widely available than those for clear liquids (Getsiner et al., 1984).

Jan 1, 1992

By A. E. Hall, D. M. Mchaina

This paper outlines a proposed research project to investigate secondary sulphide ignitions. Sulphide dust explosions have resulted in loss of production and considerable capital and equipment replacement cost in Canadian mines. The practical application of laboratory test results to actual mine situations presents a complex problem and is a field requiring immediate investigation. The factors contributing to the outbreak of sulphide ignitions are not clearly understood. This indicates a need for future research to study the influence of blasting parameters, exhaust temperatures, and dust characteristics on secondary ignitions at source. The aim is to establish realistic quantities for each of the parameters and develop a model that will incorporate field and laboratory quantities. It may be possible to predict outcomes of sulphide ignitions when the parameters are known. It is also planned to study the techno-economic feasibility of the preventive and control methods. One aspect of planned future research requires quantification of some terms by obtaining measurements of pollutant concentrations and size distribution of the airborne dust in an underground environment immediately after a main blast. A blast-proof aerosol sampling package to measure the source term will be designed. This sampling package will consist of a sampling section and a shield which will be capable of withstanding a blast explosion. The accuracy in measuring the variables and combination of variables will be the main focus in this proposed study.

Jan 1, 1987

By John W. Rushton

THE PLANNED MAINTENANCE PROGRAM All concentrators should start with a planned maintenance program from day one. Every- body thinks they have a program in place before start-up, but in reality, most have only a fraction of what is needed to avoid the "Post Start-up Disaster" (PSD) - two years for start-up is not that uncommon. An effective program has all of the following: (1) Good people. (2) Area Maintenance. (3) Good PM Checklists. (4) Daily Work Schedules. (5) Written Work Orders. (6) Equipment Histories. (7) Backlog Control. The installation of a workable program takes hard work, talent, and commitment. You have to know what you are doing (hard work will not replace talent). Good People Good people are available in any location if you make the effort. Always check references carefully (both superiors, peers and subordinates). Was the last concentrator they worked at successful? Was it clean? Find out! Success or failure follows people around. I know people who are experts on PSD because they have lived through it three or four times. You need some college trained people with hands-on experience. There are no secrets, you have to make the effort. If you make a mistake in hiring (and you probably will), make the tough decision necessary to rectify it quickly. Area Maintenance Area maintenance refers to organization of supervision such that one person is uniquely accountable for every inch of ground and piece of equipment. Avoid overlapping authority if at all possible. You must have a planner as a staff position. A foreman cannot effectively plan and

Jan 1, 1986

By J. S. Stachulak

Inco Limited operates nine underground mines on the rim of the Sudbury Basin. These operations are situated near the City of Sudbury, 589 km (365 miles) west of Montreal, and 363 km (225 miles) north of Toronto. The ores are mined primarily for nickel and copper, and the principal minerals are pentlandite, chalcopyrite, and pyrrhotite. Total ore production from underground is in excess of 51,000 tons per day. The total volume of fresh air supplied to the nine mines is six million cubic feet per minute. There are 50 main fans in operation at these mines, powered by electric motors totalling 11,200 kw (15,000 hp). The trend in metal mining during recent years towards mechanization and high-tonnage production methods has greatly increased ventilation requirements. The flow of air must quickly dilute and carry away diesel exhaust fumes, dust created by mining operations, and the fumes of the explosives used in blasting. Mechanical ventilation is required to obtain the necessary volume and control, as natural ventilation pressures alone are, for the most part, inadequate and unreliable. In the event of a mine fire or other needs, close control of ventilation is essential. There are two unique heating systems presently in operation at Inco: Creighton Natural Heat Ex- changer and Stobie Ice Stopes.

Jan 1, 1989

The trend in the U.S. coal industry in recent years has been a continuous increase in the percentage of coal produced by surface mining methods. Though the predicted energy demands promise a good market for coal, growing legal and environmental issues make the exploitation of a coal deposit by surface methods a difficult and challenging task. Major emphasis has to be placed on the development of integrated mining and reclamation schemes which enhance the possibilities of post mining land uses. Since no major breakthroughs are foreseen in the near future in surface mining equipment, innovative applications of current equipment must be developed. Draglines have been and are expected to continue as the primary earthmovers in surface mining of coal. A dragline simulation model has been developed which has the capability to analyze various deployment schemes such as conventional side casting, advance benching, and extended benching. The mathematical aspects of the model, the input data, and the output results are discussed with reference to an application in an operating mine. The model can be used to select a suitable dragline for given geological and mining conditions and to study the effect of alternative mining layouts and spoiling plans on machine production.

Jan 1, 1979