Search Documents

By Heinz Hofmann

In order to drive tunnels with low overburden in town regions, it is necessary to give a quantitative prognosis for the deformation of the underground as well as of the tunnel-lining and of its stability. These problems and their solutions are illustrated by the works for a two-track-railway-tunnel in Bochum (Ruhrdistrict). In this case the most important problems consisted in passing below buildings in a vertical distance to the fundamentals of only 3.20 m and a railway earthdam with rapid train traffic in a distance of 4 m under the dam. The results of measurements from other comparable tunnels and finite-element-computations were used to prognose the settlements on the surface and in the ground, their distributions and their development in time. To obtain these values at the site, a special system of tunnel driving was executed. The tunnel was excavated with the newest type of tunneling-machine from DEMAG, cutting an inclined front, immediately followed by a special temporary support of shotcrete and inclined steel-ribs. By using theoretical and empirical methods to assess the behavior of the tunnel and underground and by executing an optimal driving system in technical as well as economical aspects, the expected behavior, expressed in quantitative values, was almost equivalent to those received by control measurements.

Jan 1, 1974

By A. D. Davis, C. J. Webb

Brohm Mining Co.'s Gilt Edge Mine in the northern Black Hills was a surface heap-leach operation that was active from the 1980s until 1999. Financing problems and acid drainage concerns at the mine were reported in the late 1990s. In February 1999 the Governor of South Dakota announced plans to request the US Environmental Protection Agency to help clean up acidic water at the mine and reclaim the site. In July 1999 the parent company of Brohm, Dakota Mining, filed for bankruptcy in Canada. Because of the bankruptcy and environmental problems, the State of South Dakota intervened and began water treatment. The mine was declared a Superfund site in 2000. Hydrologic issues include the potential for acidic drainage from the site. The mine is at the headwaters of Strawberry Creek, which drains into Bear Butte Creek. About four miles downstream, Bear Butte Creek loses its discharge to swallow holes in the karstic Madison Limestone aquifer, a regionally extensive and valuable groundwater reservoir. Other concerns at the site include treatment of acidic water in mine pits and a waste rock dump.

Jan 1, 2003

By W. G. Pariseau

Recent advances in rock-mass mechanics and computational technology now allow for the stability analysis of excavations in "wet" mines where mining-induced changes in rock mass deformation and fluid flow are coupled and time dependent. In addition to water pressure and flow in jointed, possibly porous, rock masses, all of the usual dry-mine parameters, including the premining stress state and rock-mass properties, are taken into account. Finite-element analyses of shafts and tunnels, as circular, elliptical, rectangular and arched-rectangular hole shapes excavated in an initially stressed and pressurized rock mass, indicate that the usual guidelines for optimum shape and orientation of single openings apply. Here, optimum means maximizing the minimum wall safety factor or, equivalently, minimizing the peak stress concentration. The results also show that failure originates in elements at the wall and the minimum safety factor at the wall in the wet case is always less than the dry case, regardless of drainage time allowed.

Jan 1, 1997

By B. J. Arnold, C. D. Harrison, R. A. Lohnes

More than 544 Mt (600 million st) of coal are handled annually for use by this country's coal fired power plants. Coal is transported in various ways: overland conveyors, railcars, trucks and barges. It can travel short distances or thousands of miles, picking up moisture, freezing or drying. When the coal is received at the power plant, environmental problems with fugitive dust and further handling problems can arise. To ensure that power plant availability is not jeopardized by coal handling problems, the Electric Power Research Institute's (EPRI) Coal Quality Development Center (CQDC) developed a research program aimed at addressing utility coal handling problems. The program has identified key areas, and is investigating the cost and cause of coal handling problems as well as the solutions to these problems. The ultimate goal of the program is to develop a "handleability index" that utilities can use in their coal specifications or hardware for a utility's sampling system to predict handleability and determine if a coal shipment should be accepted.

Jan 1, 1993

By Philippe Dumont

Presentation of the project Underground civil works to be performed They include two single track running tunnels and a service tunnel of a length of fifty kilometers . Many cross adits (180 adits) : to link the tunnels (53 cross passages), to relieve air super pressure from one tunnel to the other (87 piston ducts), to install technical adits (40 electrical rooms). Two cross-overs located at one third of the whole length, allow trains to shunt from one tunnel to the other so as to ensure one way traffic in case of emergency. Pumping stations allow water to be collected at the lowest point and pumped out. 1 Main features of the tunnels 1.1 The service tunnel This 4.8 m inner diameter gallery allows During civil works - front probing operations of the geological layers encountered (front and vertical probes). - lateral soil grouting that may be necessary to facilitate the boring of the two running tunnels . During operations - Maintenance and safety vehicles traffic - Fresh air supply to running tunnels - Fire protection and drainage system - Electricity supply and control and communication. The service tunnel has been bored with a 5.72 meter external diameter Robbins TBM for the undersea section, and a MITSUBISHI TBM for the land section.

Jan 1, 1991

By Al Sylvester

The drill-and-shoot excavation of the two underground Pumphouses for the Metropolitan Sanitary District of Greater Chicago's Mainstream Pumping Station is described. The construction sequence involved the concurrent excavation and support of the two 19.2 m (63 feet) wide by 83.6 m (274 feet) long by 29.3 m (96 feet) high caverns. Excavation was interrupted after taking the 6.1 m (20 feet) high top heading in order to cast-in-place a 0.2 m (8 inch) thick by 19.2 m (63 feet) wide concrete arch. The remaining 23.3 m (76 feet) of rock was then excavated in benches below the concrete arch. PROJECT DESCRIPTION Twenty-four kilometers (15 miles) southwest of the city of Chicago, Peter Kiewit Sons' Co., in a joint venture with John F. Shea Co., and Kenny Construction Co., has successfully completed the construction of the Mainstream Pumping Station for the Metropolitan Sanitary District of Greater Chicago. The five year, 169 millon dollar project is a vital component in Chicago's Deep Tunnel and Reservoir Plan in that its function is to lift the sanitary/ storm sewage back up to grade from 107 m (350 feet) below ground, and pump it to the treatment facilities 8 km (5 miles) away.

Jan 1, 1985

By Shaning Yu, Yosry A. Attia

The purpose of this work was to investigate the feasibility of using column flotation as a floc separation technique. In this study, the ultrafine coal (minus 25 microns) slurries were cleaned by using the Integration of column flotation with selective flocculation. It was found that using column flotation as a floc separation technique during the "cleaning" stage, achieved much better results than that either using column flotation as a rougher separation technique for coal flocs, or using It directly to recover the ultrafine coal from the slurries without adding selective flocculant. Thus, the ultrafine coal slurries were first separated by selective flocculation process to reject a certain amount of the dispersed ultrafine ash minerals, and to aggregate the ultrafine coal particles as flocs. Thus, the entrainment of ultrafine ash minerals Into the coal floc-froth concentrate during flotation could be considerably reduced. Subsequently, the coal flocs were further "cleaned" by column flotation. The experimental results Indicated that this approach was technically feasible and particularly suitable for a slurry containing a large amount of ultrafine particles. The effect of flotation time, and collector dosage on column flotation of coal flocs were also Investigated and reported In this article.

Jan 1, 1988

By F. L. Wilke

In the german hard-coal mining industry the mechanization of longwall faces and the machinery used for the extraction process have reached such an extent, that an extensive increase in productivity and face performance is not likely to be expected. At present, the greatest amount of man-shifts is needed for operations such as tunneling, transportation and haulage (fig. 1.). The most restrictive parameter, especially considering the possible ad- [ ] vance rate of faces, is the comparatively low advance rate achieved in drifting operations. Therefore improvements in productivity and advance rates of drifting operations will have considerable influence onto the extraction rate of the faces. The importance of drifting operations - and especially the so-called "conventional drifting by drilling and blasting" within the scope of long- term planning strategy of the german hard-coal mining industry is reflected by the development factor. This factor is given by the ratio: cubic meters of rock excavated in drifting per 1.000 tons saleable coal produced. In 1973, which is considered to be the beginning of the oil-crisis, this factor was determined to be 17.7 m3/ 1.000 tons sale- able coal.

Jan 1, 1982

By Roderick K. Davey

The objective is to develop a short-range mining plan which satisfies management and operating criteria and also "dovetails" with the long-range mining plan. In the past years, this objective was accomplished entirely by manual methods. Today, the computer is used to assist the engineer with this task. The results provided by these programs usually are incomplete and require further manual manipulation. The advantage of using the computer programs is that the program can be used to evaluate alternative plans on a first-cut basis minimizing the manual work. Subsequently, the most promising alternatives can be analyzed in more detail, commencing with the first-cut results. In this specific case history, one technique for using computer programs to assist with short-range mine planning will be discussed. Some of the basic operating and management criteria considered directly and indirectly are as follows: (1) operating criteria which include minimum and maximum shovel cut size, equipment performance, haulage roads, requirements for blending, and plant capacities; and (2) management criteria which consist of production requirements, cash flow requirements, return on investment, market demands, and availability of capital.

Jan 1, 1979

By Solomon S. Katz

As more and more computer software is written for geological mapping applications, the users of the software are discovering the problems of transferring data between the programs, maintaining correct data and integrating maps produced last week with those produced today. One way to deal with these situations is by using a geographic information system (GIs). Last September the USGS and National Academy of Science held a 5-day GIs symposium on integrating technology and geoscience applications (USGS, 1988). It was followed in October by GEOTECH '88 (Peters and Krajewski 1989) which had a session exclusively for GIs applications in the Geo-Sciences. Editorials in Geobyte (Leonard, 1986, 1988) suggested that geographic information systems will be the next major computer programs to be adopted by the mineral industries. As far- back is 1985, the Computer Oriented Geological Society (COGS) printed An Introduction to GIs in their newsletter (Katz, 1985). About 20 years ago, a revolutionary idea occurred in the world of business data processing. It was the idea that all related data be stored in a standard format, in a single place and that all related computer application programs would use the same data.

Jan 1, 1989

By Ümit Yasar Onder, Tevfik Prof. Dr. Güyagüler

This paper describes the results of an investigation done to determine thermal properties and heat emission of coal measure rocks in Karadon district of Zonguldak Coal Colliery. In Karadon District, depth of working level is about -600 m where the heat problem arises. In the near future, workings will be at deeper levels and working conditions will be more difficult due to high heat emission. At the beginning of the paper the importance of wall rock heat emission in underground mine have been explained and then the amount of heat emission to the ventilating air has been calculated. It has been found out that the strata is the main source of heat in the mine. Therefore, geothermal gradient of the region has also been determined simply by measuring the virgin rock temperatures in different levels of the mine. All other data directly related with heat emission from different sources has been collected and has been analyzed by using a special computer package. As a conclusion, total heat and moisture content in ventilating air and heat balance has been determined for Karadon Coal Mine. In addition, some recommendations and suggestions have been made for the future works when the mine workings go to the deeper levels.

Jan 1, 1995

By D. Hodouin

The optimisation of mineral processing plants requires the evaluation of performance indices such as production rate, product quality, valuable mineral recovery and process efficiency. Decision to change operating conditions or equipment to improve plant performances rely on the significancy of the estimated performance indices. The better is the quality of the estimation, the better is the discrimination capability of the index and as a consequence the larger is the operation improvement. The reliability of performance calculation depends on the sensors nature, accuracy and location, on the data redundancy, on the correction method applied to raw data and finally on the propagation of measurement errors along the calculation of performance indices. To maximize the quality of the data collected for performance evaluation, the following techniques are presented, discussed and illustrated: redundancy and observability analysis, data filtering for mass conservation, variance analysis of performance calculation, and data acquisition strategy design.

Jan 1, 1991

By Glenn L. Krum

Inflation has received much attention due to its effect on capital budgeting, associated cost overruns, and declining real profits. This study focuses on the effects of inflation on the evaluation of a mining investment and the estimation of a mining project's revenues. The study indicates that the best method for estimating future returns is the fore- cast dollar scheme. In this scheme, the metal price was held constant, and the operating costs were "inflated" along a historical regression line. The conclusion was reached by comparing the "actual" performance of a 3000 tpd (tonnes per day) lead mine model with 'its estimated performance during four time periods (1950-1960, 1955-1965, 1960-1970, 1965-1975). The individual data files for each time period and estimating method (6 files by 4 time periods) were pro- cessed by a suite of cash flow computational and investment analysis sub- routines. The analysis presumed that the mine was part of a large corporation which could utilize the expensed, development and exploration costs and any investment tax credits, in the year that they were incurred.

Jan 1, 1979

By Rogério C. Guimarães, Antonio E. C. Peres

Arafertil's oxidized ore presents barite grades that oscillate between 5 and 12%. The barite separation plays a major role in the production of apatite concentrates for the manufacturing of phosphate fertilizers. The selectivity, via flotation, in the system barite-apatite is inherently difficult due to the similarity of the physical/chemical characteristics of these minerals. The evaluation of the relevant aspects of this separation was performed based on the determinations of the electrical surface charge of barite and apatite, the abstraction isotherms of cetyl-stearyl sodium sulfate and fatty acids soaps for barite and apatite, microflotation in a modified Hallimond tube, and flotation tests in a batch column. The results showed that the adsorption of cetyl- stearyl sodium sulfate occurs preferentially onto barite, in comparison with apatite. On the other hand, the rice bran oil soap presents similar adsorption levels onto both barite and apatite. The cetyl-stearyl sodium sulfate was selective as a barite collector in the presence of apatite, a fact that was not observed in the case of rice bran oil soap.

Jan 1, 1999

By I. E. Zevgolis

A comprehensive critical review on the subject of sulfates-induced swelling behavior of lime-treated soils is presented in this study. Starting with the description of a well documented case study, the mechanisms behind the swelling behavior and the factors that affect this behavior are discussed. Then, the major experimental methods of sulfates content determination are briefly presented. Finally, an attempt is made to categorize sulfates level and equivalent risk for civil infrastructure. The paper indicates that limited work has been done, not only on identifying safe conditions for use of chemical stabilizers in presence of sulfate rich soils, but also on developing materials and methods to avoid, or at least mitigate, the problem.

Jan 1, 2008

By C. Abbruzzese, L. Piga, P. Fornari, S. Ubaldini, R. Massidda

The effects of certain variables on the extraction of gold by thioureation have been investigated on a quartzose gold-bearing ore using a statistical multifactorial strategy. The factors taken into consideration were milling time (which corresponds to a given grain size), oxidant concentration, thiourea concentration and liquid/solid ratio. The influence of these four variables was ascertained first by a full factorial design at two levels for each variable (16 runs). This permitted the estimation of first-order effects of the factors affecting the process. Then 9 runs were added whose levels were both in the centre of and outside the axes of the previous plan thus originating a central composite design. This permitted estimation both of second-order effects of the factors involved and of parameters of a second-order polynomial model. The results show that extraction of gold depends only on milling time and oxidant concentration, at least in the experimental range considered. The equation fitting experimental data, as calculated by the least squares method, allows a response surface to be drawn. Due to the low gold grade of the ore (6 ppm) statistical analysis could lead to contradictory results, hence strict observance of Gy's rules for sampling and very accurate and precise chemical analyses were required.

Jan 1, 1995

By C. L. Schaidle

Computers and communications technology have revolutionized many industries. In earthmoving, this revolution has just begun. The major changes are still to come but are just around the corner. This article presents a vision of this upcoming revolution in the earthmoving industry. This vision includes basic communication, machine monitoring and diagnostics, job and business management, planning and operations, and machine control. For the industry to realize maximum benefits from the information age, it must have a vision of the future that is shared by technologists, machinery producers and miners. History of the information age During the 1970s, the information age revolutionized retailing, starting with the grocery business. By using bar codes and laser scanners, individual items were connected to the information world of computers and communications. Once this connection was made, the data on what an item was and where and when it moved became valuable information for inventory control and marketing. Not only was the information valuable, it was easy and inexpensive to collect and manipulate. The effort required to provide the consumer with the right product at the right time was reduced. Costs went down and customer satisfaction went up. But there were casualties of this revolution. Many inventory counters lost their jobs. There were also equipment casualties. Cash registers that could not interface with the digital world were discarded long before the end of their useful life.

Jan 1, 1994

By James R. Miller

Recent experience over extensive areas of the Basin and Range Province has demonstrated the importance of the basin's (valley's) geology and geomorphology in locating large quantities of good-quality aggregate. First, a geologic map depicting basic geomorphic-geologic units in a valley is made in the office from aerial photography. Next, derivative maps are made from geologic maps and field-derived information such as parent rock type, source area and depositional environment, relationship to adjacent deposits, and Quaternary geologic history. Studying the derivative maps leads to selection of test sites for potential deposits of high-quality aggregates. Subsequent field studies provide more detailed information about geologic processes and samples for laboratory testing. Combining all information allows the characterization of aggregate potential of very large areas. Favorable areas can be further tested. This phased approach has proven to be cost effective. The methodology used in mapping and characterizing basinfill deposits is applicable over much of the western United States. Map units were developed by focusing on the predominate geomorphic process, grain size, cementation, and relative age. The resulting functional map units are of use to engineers and planners. This study led to many conclusions, including the fact that the best quality basinfill aggregates are found in selected alluvial fan deposits and Pleistocene lakeshore deposits. The best quality aggregates are derived from Paleozoic carbonate and quartzitic parent materials that can also provide high-quality crushed-rock aggregates.

Jan 1, 1987

By Peter Kowalczyk

The acquisition of submarine gravity data using airborne gravity technology is a practical reality. Ocean Floor Geophysics plans to deploy a free-swimming ROV based submarine gravimeter on a commercial basis in early 2009. The submarine instrument is a variant of the well-used GT-1A airborne gravimeter. Airborne gravity surveys are now routine. The primary factor controlling the accuracy of airborne gravimeters is the precision of the GPS measurement of vertical movement of the sensor platform. The gravity measurements along a flight line are the differences between the output of the gravimeter vertical accelerometer and the estimate of the aircraft vertical acceleration using the differential GPS system. The principle difficulty of moving an airborne gravimeter to a free-swimming submarine platform is the necessity to have an accurate real time estimate of the changing elevation and hence changing vertical acceleration of the platform; GPS doesn't work underwater and an accurate estimate of depth fluctuations to the necessary precision is difficult to acquire. It is interesting that the airborne gravity gradiometer technology, which competes with the airborne gravity technology, was first developed as a classified military application for use by missile submarines during the cold war. Gradiometers were developed for this application specifically to avoid this problem. A gradiometer does not require as accurate an estimate of its vertical position to make a useful reading- it measures gravity gradients, not the gravity field itself.

Jan 1, 2008

By J. R. Stoltz, E. Thompson, S. Pattee

On May 15 and 16, 1999, a mine ventilation survey was performed in the 705-m- (2,312-ft-) deep Cayuga Mine, Cargill Salt Division, Lansing, NY. The purpose of the survey was to develop a numerical model of the existing ventilation system and to perform a computer simulation study for long-term environmental and ventilation planning. Because the natural ventilation pressure (NVP) has significant effects on the ventilation system at the Cayuga Mine, there was a need to assess the NVP acting in the mine. Due to the ventilation arrangements in the Cayuga Mine, the authors decided to use the direct-measuring method to determine the NVP by measuring differential pressure across the automatic fan door. This difference in pressure was measured immediately after the fan was stopped and the automatic door was closed to stop the flow throughout the entire mine. To show seasonal changes in NVP, two additional measurement for NVP were performed, one on Aug. 22, 1999, during the hot (summer) season, and another on Feb. 6, 2000, during the cold (winter) season. The mutual interaction between the natural ventilation pressure and the main fan at the Cayuga Mine is also discussed

Jan 1, 2003