Search Documents

By Raphael G. Kazmann

The predicted warming of the earth's surface, presently the subject of much debate, controversy and legislation, is based on what is termed "the greenhouse effect." This is the result of the property of certain atmospheric gases. These gases allow the passage of radiant energy to the earth's surface and reflect back, to the earth, the infrared radiation given out by the heated surface. Physicists have computed that if there were no greenhouse effect the average temperature of the earth, now about 15° C (60T), would be close to -18° C (OT). Just what gases have produced this salubrious effect? Water vapor is the most important. Then come carbon dioxide, methane and a number of minor constituents of the atmosphere, both natural and man-made. Climate change, its cause and its impact on human activities have been the subject of scientific and historical study for more than a century. Recently, some scientists have concluded that if the man-made increase in the carbon dioxide and other greenhouse gases continues, by the late 21st century the earth's global average temperature will rise between 2° to 8° F. This temperature rise would cause the water in the oceans to expand and the massive polar glaciers to melt. In 1980, it was predicted that the sea level would rise 7.6 m (25 ft) by the late 21st century. By 1985, the predicted rise was 1 m (3 ft); and by 1989, it was 0.3 m (1 ft) (Jastrow, Nierenberg and Seitz, 1990). Agricultural scientists have pointed out that an increase in atmospheric carbon dioxide would enhance biological growth including the production of foodstuffs.

Jan 1, 1992

By Todor P. Stefanov

The thermal draught within ventilation networks of underground mines depends to a great extent on the shafts depths and degree of change of ventilating air density. When the topology and space orientation of a ventilation network are constant, the dynamics of thermal draught is determined mainly by the variations of the heat- and mass-transfer processes in the openings. This conclusion follows from the well known basic theoretical notions about the thermal draught-aerostatics and thermodynamics [1]. Quantitative evaluation about the influence of heat- and mass-transfer processes on dynamics of thermal draught could be made through: direct mine measurements, special experiments and with the aid of mathematical models. The first two methods produce sufficiently accurative results, however it is very difficult to perform such studies, particularly when these processes are evaluated within a large scope and multifactor aspects. Mathematical models of thermal draught allow to overcome easily these difficulties. The degree of accuracy of results, obtained by this method, depends to a great extent on the degree of approximation achieved by the model to the real heat- and mass-transfer processes. In this paper, with the aid of Bulgarian developed method, algorithm and computer program V WT-4 - for complex evaluation of ventilation parameters in active mine ventilation networks [2], the authors investigate some changes in the thermal draught. Basically, the method is an iterating evaluation of an open set of equations, which represents relationships between the following basic parameters of a mine ventilation network: [ ]

Jan 1, 1980

By C. A. Pickles, D. Mallette

Silicon nitride (Si3N4 ) is an advanced structural ceramic materia1 which is presently being considered for a number of potential engineering applications, particularly in heat engines, gas turbines, and electronics. With respect to other structural ceramics, silicon nitride has relatively low thermal conductivity and thermal expansion coefficients and a moderate elastic modulus. Thus, during thermal cycling the stresses developed in this material are lower than in other structural ceramics. At the present time silicon nitride is produced via three main processes: thermal decomposition of silicon imide or amide, treatment of silicon tetrachloride or silane vapour with ammonia and nitriding of silicon powder. These three methods of production are discussed with particular attention to the effect of morphology and phase content on the properties of the final product. In this work carbothermal production of silicon nitride has been studied in a high temperature resistance furnace. Compacted briquettes of silica and carbon were produced which were reacted in a nitrogen atmosphere. The optimum reaction temperature and the carbon to silica ratio were found to be 1425OC and ten to one, respectively. The presence of large amounts of ash in the reductant promoted the formation of silicon nitride. The specific surface area of the briquettes did not have a large effect over the range studied in the present work. Briquette seeding with small amounts of Si3N4 was effective in increasing the reaction rates.

Jan 1, 1990

By J. J. Krizek, A. H. Ditto

INTRODUCTION The Carr Fork property is situated in the Bingham Mining District located on the east slope of the Oquirrh Mountain range in Utah. The mine is adjacent to and lies west of Kennecott's Bingham Pit some 25 miles southwest of Salt Lake City. The Bingham Mining District contains one of the largest copper reserves on North America. Mineralization is associated with the Bingham stock which intruded through some 16,000 feet of sedimentary formations. Mineralization and a1teration zoning was developed radially from the Bingham stock with lower grade disseminated copper mineralization centrally located in the stock and adjoining quartzites. In addition, several garnetized limestone beds abutting the stock were also well mineralized. These skarns will be Carr Fork's initial mining target. Of the several limestone beds, only two, the Yampa and the Highland Boy have significant commercial interest at present. These beds which are 50 feet to 150 feet thick and are separated by 200 to 400 feet of quartzite were highly folded, thrusted and faulted, resulting in a dip variance from 20" to vertical. The predominant dip, however, is between 20" and 45" from horizontal. Quartzites surrounding the limestone beds were subjected to the same degree of tectonic activity with resultant intense fracturing and stress relief. The limestone beds which have a higher elastic modulus and which also experienced fracture healing during mineralization appear to have greater competency and strength than the quartzites. Four shafts nominally 3500 feet deep will provide access to the mine which will be a highly mechanized trackless operation, designed to produce 14,000 tons per hoisting day. First production is scheduled for the last quarter of 1979.

Jan 1, 1977

By Randhir Sehgal

If the primary purpose of a control system is to assure a fixed-quality product at maximum yield, the real issue involved in control of the fine coal cleaning circuit in a plant is to demonstrate that control is technically feasible and economically beneficial . This paper suggests that it is not easy to do so in most cases. Fine coal, defined here as the 28 mesh x 0 fraction of the plant feed, is generally cleaned using a combination of hydrocyclones and flotation. Both of these processes are relatively insensitive to changes in operating variables. Further, the fines fraction general 1 y forms no more than 20% of the plant feed and, at times, is as low as 10%. The instruments to measure flow rates, densities, and product qua1ity (ash, sulfur, etc.) are not sufficiently accurate to allow effective responses to changing state variables and product quality. It is sufficient to run the fine coal circuits at maximum recovery, and the control of product quality and optimization of yield should be achieved by controlling the coarse coal circuits and measuring the quality of the entire clean coal leaving the plant. This contention is made with particular reference to U.S. plants cleaning coal for the utility industry and should be viewed in this context only. It is explicitly admitted that this strategy is mathematically non-optimal in the sense that all size fractions are not necessarily cleaned at equal elementary ash, and would result in a loss of yield. However, under the conditions of conventional coal cleaning practice, this is a sensible approach.

Jan 1, 1988

By T. L. Brekke, T. R. Howard

Stability of an underground opening can be defined in several ways. To geologists and engineers that are used to working in geological environments where the major parts of the works after careful scaling can be left unsupported during the construction period as well as during operation, any rock mass behavior that requires reinforcement, support or lining may be regarded as a stability problem. To colleagues excavating underground openings in geological environments that require continuous use of reinforcement or support and lining "stability problems" are often associated only with those parts of the work where "standard" construction procedure and method of reinforcement or support and lining is inadequate, and special measures therefore needed. In either case, a major objective is to assess the stability problems correctly -as far as possible at the planning stage -- and choose methods for excavation and reinforcement or support that will bring the opening safely and as economical as possible through the problem areas. INTRODUCTION It is not uncommon that stability problems associated with faults or seams have been described as "unexpected." This term has unfortunately been used to indicate that no one knew that the fault or seam existed prior to excavation. A careful review of documented cases where serious stability problems have occurred revealed that the existence of these zones most often was known, but that their behavior was incorrectly assessed prior to or during construction. Miscalculations have been made in terms of the type and magnitude of loads that developed, and in particular in terms of the time-dependant behavior.

Jan 1, 1997

By Tom McDonald

Test work and plant operation confirmed that semiautogenous (SAG) milling is a viable option for Inco's milling rationalization project at Sudbury only if pebble crushing is included. Throughput increases more than 50% with pebble crushing incorporated into the comminution process. The finer product of high-speed pebble crushing provides further energy savings. The unconventional approach of pumping the pebble crusher product, while simplifying plant layout, has produced challenging wear problems. Inco Ltd.'s Sudbury operations are located in northeastern Ontario, Canada, about 400 km (250 miles) north of Toronto. Inco has 11 operating mines around the rim of the Sudbury basin. The mines currently produce about 11 Mt/a (12 million stpy) of ore. This ore contains pentlandite, pyrrhotite and chalcopyrite in mafic host rocks. The milling facilities are designed to produce 108.8 kt/a (240 million lbs/ year) of nickel as concentrate. This concentrate is further processed through Inco's smelting and refining facilities to produce nickel, copper and several other metals. Before 1991, -200 mm (-8 in.) ore was shipped to two primary mills. The Clarabelle mill had a design capacity of 29 kt/d (32,000 stpd). Frood-Stobie had a capacity of 16.3 kt/d (18,000 stpd). The flowsheets of these mills were similar. Two stages of open-circuit crushing were followed by rod milling and closed-circuit ball milling. The product from the comminution circuit, at 12% +250 mm (+65 mesh), was first passed through magnetic separators to recover magnetic pyrrhotite. It was then sent through a four-stage flotation process. The first two stages produced a high-grade copper-nickel concentrate. The final two scavenger stages produced a low-grade copper-nickel concentrate containing nonmagnetic pyrrhotite.

Jan 1, 1992

By J. F. T. Agapito, C. E. Brechtel, C. J. Gilbert, T. R. Kelly, R. C. Karlson

A multi-lift benching cut-and-fill mining method was adopted at Asamera Minerals (U. S.), Inc.'s Cannon Mine to balance the goals of high productivity and near 100 percent recovery with the need to minimize subsidence. High strength backfill was required to provide effective long-term overburden support and safe working conditions during the pillar recovery operations. Operational designs were evaluated using numerical modeling to predict global mine stability and backfill strength requirements. These models incorporated sequential mining of primary stopes, backfilling of primary stopes and recovery of pillars, and have been transferred to the mine operations group for use in evaluating different production sequences. The modeling has provided a better understanding of the structural response of the mine to excavation of the primary stopes and removal of the pillars. Predictions about the transfer of overburden weight to the abutments, pillars and cemented fill pillars have provided a criterion to evaluate mining plans and production sequence. Comparison of these predictions with actual mine structural performance has developed confidence in the design of the mining method and in the geomechanical design methods being employed. Primary mining of the B-North zone is nearly complete, and the stopes have been generally stable, as projected in the original design. Some exceptions have occurred where locally stope pillars have failed due to the presence of adversely oriented sheared beds. Recovery of the pillars between the

Jan 1, 1987

By F. N. Kissell

The US Bureau of Mines undertook a study of those factors influencing worker escape from an outby coal mine fire. The results of this investigation were two-fold. First, those factors affecting escape from a mine fire were defined, and second, the relationships between these factors were identified. Although the individual components had been studied before, little information was available on their interdependence. Fault tree analysis was used to evaluate the miner escape scenario. After constructing the fault tree, a two-phase analysis of the tree was conducted. During the first phase, the minimal cutsets of the fault tree were identified and ranked. These sets were the smallest sequence of events leading to fatalities during the fire. This ranking revealed that reduced evacuation delays, improved self-rescuer training, and improved stopping construction were important in controlling fatalities during escape from the mine fire. The second phase involved additional analyses of the fault tree. These evaluations were started by first determining occurrence probabilities for each event in the fault tree. Two types of sensitivity analyses were then conducted. The first analysis dealt with changes in event probabilities and their impact on the likelihood of fatalities. The final sensitivity analysis considered dramatic reductions in the probability of fire fatalities. This revealed what event probability values were necessary to reach this level. These results have revealed various remedial actions that could be used to improve the survivability of an outby mine fire.

Jan 1, 1990

By Jean-Michel M. Rendu

According to statistical theory, the geostatistical methods of ore reserves estimation are greatly superior to any other method. However acceptance of geostatistics by the mining industry has been slow and not as wide spread as one would expect. One of the reasons for this cautious approach is that it is often questioned whether the geo- statistical assumptions are satisfied in real world situations. When blocks of ore are estimated in a mineral deposit, geostatistical theory can be used to determine which method of estimation should give the best results. Using this theory, the relationship between estimated value and true block value can be quantified. There is a need to verify that this theoretical relationship is actually observed in practice, and that the block estimates ' obtained using the theoretical ly best method of estimation, are actually most similar to the true block values. In this paper the results expected according to the theory are compared with the results actually obtained. Sample values from a large bedded gold deposit have been used. Blocks of ore have been estimated by a number of methods, including the polygone, inverse power of the distance, kriging, logarithmic kriging and other geostatistical methods. The block estimates have been calculated from samples on a large grid, and compared with the true block values obtained from additional samples on a much smaller grid. The results of this comparison show extremely good agreement between theory and actual results.

Jan 1, 1979

By W. Blake, J. Mahaut, W. Hustrulid

Division II at Kamoto mine in Kolwezi, Zaire represents a transition zone between Divisions I and III where transverse and longitudinal cut-and-fill rooms were being mined. Because this transition zone had been geologically depicted as being badly faulted the mining in this division had been deferred to a future time. However, to increase production and to reduce mining costs by carrying out the mining of the 3 divisions simultaneously, it was decided to mine Division II. The mining research group of Gecamines was given the task of designing a mining geometry then testing this design in a full scale test. Based on an evaluation of the faulting and fracturing of the 2 parallel orebodies and on an extensive in situ testing program preliminary mathematical analyses were used to develop and evaluate room and pillar designs in the 35°-65° dipping bedded formations. Based on these analyses and the constraints of having to fit the design of Division II to grade into Divisions I and III in a logical manner, a mining geometry for Division II evolved. To test this design an instrumented room was excavated in the most critical area. The results of this full scale testing showed that the behavior of the roof and wall rocks were as had been predicted by finite element computer model studies which incorporated the material properties and results of the field testing. The room geometry design was both judged and observed to be stable, hence mining commenced.

Jan 1, 1977

By S. K. Kawatra, S. A. Moffat, K. A. DeLa’O, T. C. Eisele

It was observed that the efficiency of some autogenous grinding circuits was dependent on temperature, with the energy-efficiency of the grinding process decreasing in the winter months, accompanied by an increase in critical-size production. Several possible causes of this phenomenon were suggested, including: • Increased brittleness of the ore during blasting in the pit at low temperatures, leading to increased levels of internal cracking that would lead to rapid breakage to critical size in the mill; •Brittleness changes of the rock in the mill; and • Changes in the durability of the rock caused by either formation of ice on the surface, or freezing of water inside the pores and cracks of the rock. To determine which mechanisms were occurring, drop tests were carried out using frozen and unfrozen rock with varying degrees of porosity, both dry and water-saturated, and which had been blasted for mining in summer and in winter. These tests showed that there was no difference between the summer-blasted ore and the winter-blasted ore, and that durability changes in dry rock over the temperature range from 25ºC to -25ºC were negligible. However, water-saturated rock showed an increased resistance to breakage upon freezing, particularly when the rock was highly porous, or when a layer of ice formed on the surface. Seasonal changes in the durability of rock in grinding are therefore due to formation of ice in and around the rock.

Jan 1, 1995

By G. Schmelzer

The disposal and reintroduction into recycling of residues produced by today's industrial society is not only a problem of much public debate in the countries concerned but also an increasingly prominent topic in science and research. In the treatment of most types of waste, ecological as well as economic considerations are important factors. In view of this, not only will future expenditures for treatment and processing become more significant but also, on the other hand, the savings and profits resulting from recycling. The situation described above reflects the inherent problems in the treatment of solid residues produced by waste incineration plants. The incineration of municipal waste produced approx. 2.7 - 2.8 million tonnes of solid residues in 1993 in the Federal Republic of Germany, which in part included still considerable amounts of organic and inorganic pollutants that could potentially be released into the environment. The most significant of these in terms of volume is incinerator ash at approx. 2.4 million tonnes. Through the use of innovative processing techniques, attempts are being made to convert the residues into a form that remains environmentally neutral over the longest period of time possible. One such group of techniques includes smelting technologies. After it has undergone specialised treatment, mineral incinerator ash is converted into environmentally neutral and reusable glass (vitrification) since, besides a reduction in the volume of the residues by approx. 90%, the main goal is a complete immobilisation and destruction of inorganic and organic pollutants respectively. These glasses, after they have been reshaped, are resold as commercial products such as damming or form glass.

Jan 1, 1995

By Thomas J. Rudolphi

Efficient transport of bulk materials by belt conveyor systems is an important engineering design issue, especially as conveyors become longer and power requirements increase. It is well known within the industry that the parasitic energy loss of a belt conveyor, due to the indentation of the idlers into the belt backing material can be upwards of half the total energy required to drive it on a horizontal flight. Other loss sources includes the rolling resistance of the idlers, belt/roller misalignments, material trampling, frictional and acceleration losses on loading, etc., but energy absorbed by indentation of the belt backing as it passes over each successive idler is the dominant power consuming factor. INDENTATION LOSS MODELS Models to predict the rolling resistance of a cylinder (idler) on a viscoelastic foundation (backing material) have been available for some time. As a contact problem, it is nonlinear (contact length or indentation depth is a dependent on the load and vice versa) in load/deformation response. Rubber backing material is generally assumed to behave as a linear viscoelastic solid, even though it is known that most rubber compounds retain linearity only at very low strains. Because completely general solutions are impossible, practical solutions require simplifying assumptions. Those assumptions relate naturally to two separate pans of any analytical model: I. The deformation model-aspects of the problem relating to the geometry, boundary conditions and kinematics of how the material deforms. 2. The material model-aspects of the problem relating to the material properties, or constitutive relationships, i.e., the stress/strain relationships.

Jan 1, 2008

The Mining Foundation of the Southwest will hold its 15th annual American Mining Hall of Fame Awards banquet on Saturday, Dec. 6,1997 in Tucson, AZ, preceeding the Arizona Conference of SME. The Mining Foundation's Hall of Fame, located in Tucson, recognizes outstanding contributions to the mining industry by individuals and industry partners. A permanent display of honoree vitae is located at the Arizona Historical Society at 949 E. Second St. in Tucson. Each year, one living award recipient and up to two honorees from mining history are chosen by the Hall of Fame committee and the board of governors of the Mining Foundation. In 1989, the Mining Foundation also initiated a Medal of Merit to recognize outstanding individual technical and professional contributions to the mineral industry. And in 1995, an award was instituted to recognize contributions made by companies and organizations in partnership with the mining industry. This year's inductee is James R. Moffett, chairman and chief executive officer of Freeport-McMoRan Copper and Gold Inc. He will be present as guest of honor and featured speaker. The Hall of Fame will induct John V. Dorr, metallurgist and chemical engineer. Also inducted will be Frederick L. Ransome, a geologist. Medals of Merit will be awarded to Hugo T. Dummett, senior vice president, Exploration BHP Minerals, and Spencer R. Titley, professor in the Department of Geosciences at the University of Arizona. An Industry Partnership Award will be presented to the Colorado School of Mines for its continued support to the mining industry through education and research. The banquet will be held at the The Westin LaPaloma in Tucson beginning with cocktails at 6:30 p.m. Tickets are available from Clare A. Roscoe, manager, Mining Foundation of the Southwest, telephone 520-577-7519, fax 520-577-7073.

Jan 1, 1997

By Andrew Mackenzie, Paul Rantala

Data is now appearing in literature that indicates many current paste fill systems in Canada suffer from plugged lines and severe wear rates. Both of these conditions suggest: design problems with the pipe distribution system, backfill composed of poorly graded material and/or possibly poor operator practices. Problems that can be prevented in the design stage, but still may be readily solvable with current technology. However, if left untreated will lead to an increasing frequency of down time. The compatibility of the distribution system with the paste fill rheology is fundamental and essential for the reliable delivery of fill. Either many mine operators are not familiar enough with the technology to provide a critical review that could foresee problems down the road, prior to construction and or North American designers are not clarifying their designs to their customers. The objective of this paper is to highlight key concepts to mine operators with the purpose of better enabling a critical review of contractor's/consultant's designs. There is a great deal of understanding about the rheology of backfill over a range of pulp densities from hydraulic slurry to dense to paste. However, outside of deep mines (especially in South Africa) neither hydraulic or dense fill distribution systems have suffered the problems of paste fill. Paste fill is fundamentally different from hydraulic fill principally in its transportation characteristics. These differences have a direct impact on the design of the distribution system. By understanding the practical implications of these differences the operator can play a more active role in their design while better appreciating how to best operate their own system.

Jan 1, 2001

By Gerald L. Finfinger, Michael A. Trevits

Since 1964, the US Bureau of Mines has been conducting a comprehensive program of research on the origin and control of coal bed gas. Several extensive databases have been developed during the work representing information from every major coal producing region in the United States. Gas content measurements have been made on 885 coal samples from 15 states representing 221 coal beds. Records indicate that the range of gas content varies from zero to over 640 ft3 per ton (20 cm3 per gm). During the conduct of the research program, several drilling and completion techniques have been developed or refined to divert and collect coal bed gas before it enters the mine environment. Such techniques include horizontal, cross-measure and vertical boreholes. Samples of gas collected from boreholes drilled under the program indicate that the primary gas constituent is methane which comprises 97 pct, the remaining hydrocarbons make up approximately 0.2 pct. Nitrogen and carbon dioxide account for the majority of the remaining gases at average concentrations of 1 pct each. Surveys have been made on the total daily gas emissions from underground coal mines. In fact, the most recent survey indicates that 180 mines had emissions in excess of 100 Mft3 per day (2.8 Mm3 per day). Furthermore, total mine emissions were in excess of 300 MMft3 per day (8493 Mm3 per day). An analysis of the data showed that there appears to be no relationship between in-place gas content and coal bed gas composition. Furthermore, no correlation was observed between in- place gas content and daily mine emissions. In a general sense, the higher the gas content the higher the relative gas emissions. Perhaps a more direct relationship would be observed if more complete emissions information (including gob gas borehole production) was available.

Jan 1, 1989

By Y. J. Wang

Editor's Note: Y.J. Wang's paper appeared in the September Technical Papers section. There were some inadvertent editorial errors in it. So we are reprinting it here. Abstract - This paper examines the ventilation network problem from a view point of solving a system of B equations in B unknowns, where B is the number o f branches in the network. Based on Kirchhoff s current and voltage laws, the solution to the general ventilation network problem must satisfy B network equations. In this paper, the air quantities and control-device pressures are chosen as variables and are grouped into B dependent variables (unknowns) and B independent variables, resulting in a system of B equations in B unknowns. Based on whether their variables are dependent or independent, the network branches are classified into f our types: five d, non-fixed, p-fixed, and q fixed. The ventilation network problem may include all four types of branches. There are .some conditions under which the problem as defined in this manner does not have a unique solution. To have a unique solution, the Jocabian matrix of the equations m us! he nonsingular. It then follows that: • the number of branches with independent air quantities must be less than or equal to the number of chords with respect to a spanning tree; •the subnetwork of branches with independent air quantities must not contain any cutset; and •the suhnetwork of branches with dependent control-device pressures must not contain any cutset. These three conditions must be met regardless of the values for the variables. In addition to the problem formulation, a solution procedure applying the Newton (or Newton-Raphson) method is outlined and illustrated with an example problem.

Jan 1, 1991

By N. Zouridakis

Radon is an established lung carcinogen and remains the most important environmental radiation exposure. It was estimated that inhalation of radon and its short-lived decay products accounts on average for about one half of the effective dose equivalent from all natural sources of radiation. Radon contained in household water can transferred into room air as a result of agitation or heating. An indoor air concentration of 400 Bq/m3 is obtained if the radon concentration in household water is 4 kBq/L. A typical concentration of radon in ground water is about 1000 times lower than this concentration but sometime elevated concentrations of some kBq/L in ground water are reported. In this work a Liquid Scintillation counting system is used to obtain fast and accurate measurements of radon (222Rn) in water samples from Argolida, Greece.

Jan 1, 2007

By Paul D. Dupree

Introduction Trapper mine is a dip-line strip coal mine, located about 10 km (6 miles) southwest of Craig, CO. The mine provides the Craig Generating Station, operated by Colorado-Ute, with about 2 Mt (2.3 million st) of coal annually. The Trapper mine is situated on a hillside that climbs in elevation from 2 to 2.5 km (6500 to 7400 ft) at average grade of 15%. The coal seams dip at about 16% down-grade and they outcrop near the top of the hillside. They exceed maximum stripping depth in 1 to 1.7 km (3500 to 5500 ft) of pit length. Stripping in the three existing pits is performed with three Page 752 23 m3 (30 cu yd) walking draglines. Two of the pits are currently being cast blasted. Until the active cut, the Derringer pit was cast blasted only where the lower mined seam exceeded stripping capabilities and the pit was a single seam operation. Now, a 9-m (30-ft) interburden bench has been incorporated into the stripping plan. This bench protects the first seam of coal from shear when the overburden is cast blasted. The cast blasted section of the 1.6 km (53,000 ft) long pit has been increased from the 457 m (1500 ft) casted previ¬ously to 1 km (3500 ft). High speed films show the coal losses due to shear of the blast are minimal. The pit width in Derringer pit is 61 m (200 ft). This is necessary for efficient spoil side stripping of a relatively thin interburden in the two-seam section of the pit. The Enfield pit is entirely cast blasted. The single seam pit is 46 m (150 ft) wide, 1.1 km (3600 ft) long, and varies from 15 and 46 m (50 and 150 ft) in overburden depth. The overburden strata at the mine consists of medium-hard layers of sandstone, shale, and

Jan 1, 1987