Search Documents

By J. Bigu

A theoretical radiation mine model, suitable for underground uranium nines, has been investigated. In this model, the rate of ventilation and/or the radon (thoron) gas emanation from mine walls are time-dependent. Several cases of practical interest have been investigated including sinusoidal, linear, exponential, stepwise, or a combination of two or more of the above. Analytical solutions were obtained for the time-dependent radon (thoron) gas emanation rate. However, because of the extreme analytical complexity of the solutions corresponding to the time-dependent ventilation rate case, numerical solutions were found using a special Runge-Kutta procedure and the Hamming's modified predictor-corrector method for the solution of linear initial-value problems. The mine model makes provisions for losses of radioactivity, other than by ventilation and radioactive decay, by, say, plate-out on mine walls, and by other mechanisms. Radioactivity data, i.e., radon, thoron, and their progeny. obtained with the above mine model for a number of ventilation and emanation conditions, are presented. Experimental data obtained in an inactive stope of an underground uranium mine for a time-dependent air flow case are shown. Air flow conditions (ventilation rate) were determined by tracer gas techniques using SF6.

Jan 1, 1987

By Brian H. Jasperse, Nicholson Peter J.

Gravity retaining walls have been constructed using Deep and Shallow Soil Mixing (DSM and SSM) since 1991 in the United States. These walls, for both temporary and permanent uses, were constructed by mixing cement with in-situ soils over a volume containing 100% of the required gravity wall zone. Modern design techniques have reduced costs substantially by forming the required gravity wall section as a composite mass. Using ratios of 15-35% by volume, treatment f the ground forming the required gravity section has reduced the cost from about $40 to about $20 per square foot. Design, construction and actual performance of these gravity walls are presented.

Jan 1, 1999

By R. L. Bleifuss, S. Zhong, H. E. Geotzman

Microwave heating of iron ore was investigated as an alternative to conventional reduction processes to solve the problem of slow heat transfer. Microwave heating and reduction tests were run on composite green balls made from coal and magnetite concentrate. Benchscale tests were run on both powdered and pelletized feeds using a 15 kW microwave generator. A significant increase in the reduction rate was obtained. With 20% excess stoichiometric carbon in the mix, more than 90% reduction of the iron ore can be achieved in about 10 min at temperatures of around 1,000°C. The reduction of iron ore with coal by microwave heating produces a pure, dust free, high-Btu flue gas that can be used in related thermal operations. Depending on the purity, the reduced iron product could be fed directly to an electric arc furnace for melting. In some cases, the removal of a slag phase may be required to eliminate excess silica and alumina.

Jan 1, 1997

By K. N. Han, Q. Xu

The adsorption behavior of gold in ammoniacal solutions on activated carbon was studied. The gold adsorption capacity of the activated carbon and the recovery efficiency were examined. The parameters affecting the adsorption of gold on the activated carbon included temperature, agitation speed, the concentration of cation and anion and the concentration of ammonia. It was found that the maximum gold adsorption was about 10 kg/t of carbon. The recovery of gold by the adsorption, from ammoniacal solutions was found to be dependent upon the initial gold concentration. Under experimental conditions, a gold recovery of 98% was obtained after 120 hrs of adsorption. It was also found that the initial adsorption rate was relatively fast, when compared to the entire adsorption period. The apparent activation energy for the adsorption was determined to be 15.8 kJ/mol. It was believed that the kinetics of gold adsorption on the activated carbon was controlled by pore diffusion.

Jan 1, 1997

By John R. Marks

The recent trend in the ventilation of deep under- ground metal mines in the United States is to rely more and more on refrigeration for air cooling. This paper describes the layout and the economics of the refrigeration method used by Hecla Mining Company at the Star Mine. An economic analysis must compare the benefits of an engineering system against the costs. The benefits of refrigeration, for example, are increased production rates, a better safety record, improved employee moral, and generally lower airflow requirements. Air-conditioning costs include capital expenditures for equipment, labor and supply costs for maintenance, and power costs for machine operation. A study of whether or not to install refrigeration becomes academic when a mine reaches the critical ventilation depth1 (the depth at which adiabatic compression alone produces station temperatures equal to the desired stope temperatures). Ventilation planning alternatives for such mines, including the Star Mine, are limited to the different methods of refrigeration usage. In this case study of the Star Mine, the refrigeration layout is described in detail. After the system performance is discussed, air-conditioning costs are calculated. The paper then concludes with a cost- benefit analysis of the Star Mine refrigeration system.

Jan 1, 1980

By C. Ptacek, D. Hiller, J. L. Janbor, H. Mccreadie

Between 1991 and 1994, metallurgical residues from a pressure-oxidation autoclave at the Campbell Au-quartz mine at Red Lake, northern Ontario, were neutralized with dolomite-rich flotation tailings and were deposited in a polyethylene-lined disposal area. Mineralogical analysis indicates that most of the As occurs as a crystalline ferric sulfarsenate, and some is associated with Fe oxides and with K-H3O jarosite. Field pore-water geochemical data from 1994 and 1995 showed increases in Fe(II) and As(III) concentrations, suggesting that the sulfarsenate and jarosite are dissolving; none of the discrete As phases included in a thermodynamic database limit dissolved-As concentrations, and these concentrations may continue to increase. These results demonstrate the potential for Fe and As loading through groundwater systems.

Jan 1, 1998

By J. Groppo, W. Zhang, R. Honaker

"Rare earth elements (REEs) found in coal are in the form of minerals, ion-substitution with clays and organically bound. Rare earth minerals (REMs) such as monazite exist in coal and have a grain size less than 5 microns. Froth flotation was successful in concentrating REMs existing in a thickener underflow material derived from Fire Clay seam coal which contained around 300 ppm of rare earth elements (REEs). Conditioning with fatty acid followed by processing using multiple stages of conventional flotation produced a final concentrate containing 2300 ppm REEs. Using a laboratory flotation column, a concentrate containing around 4700 ppm of total REEs was produced equating to an enrichment ratio of 10:1. INTRODUCTION Rare earth elements (REEs) are becoming increasingly important and have been widely used as raw materials for the production of phosphor, metal catalysts, magnets, and batteries [1, 2]. REE recovery from alternative sources such as coal and coal by-products has the potential to stabilize the economic viability of coal mining operations while providing a dependable supply of critical materials. The average REE content of the world coal is around 60-70 ppm [2]. There are many well-known coal beds with high contents of REEs such as those in the Far East coalfields in Russia (300-1000 ppm), the Fire Clay coal seam in eastern Kentucky (500 ppm), and the Sydney Basin in Nova Scotia, Canada (72-483 ppm) [3-6]. The occurrence of REEs in coal and coal by-products can be classified into three types, i.e., rare earth minerals such as monazite and xenotime, ion exchangeable REEs in clays, and REEs associated with organic matrix. The particle size of the rare earth (RE) minerals in coal and coal by-products is very small and normally in the micron and/or nanometer scales. The flotation technique, which is based on the surface chemistry difference, has been widely used to treat fine rare earth industrial minerals such as monazite, xenotime, and bastnaesite [7-11]. As such, flotation is a promising method for the concentration of REEs from coal and coal by-products. In the current study, rare earth flotation was conducted using the fine coal refuse generated at an operating coal preparation plant treating coal from the Fire Clay seam. REE concentration by flotation required an appropriate amount of grinding and control of the pH value while using typical collectors. Prior to RE concentration, release tests were conducted to evaluate the floatability of the recoverable coal and the REE distribution in the flotation fractions in the fine refuse. Mineralogy of the REE was studied using SEM-EDX."

Jan 1, 2017

By John Jonkman

Two major changes occured during the last 5 years in the applications of computers. First, the cost of computer equipment decreased drastically in an era of high inflation. Second, technological breakthroughs in hardware and software have been applied successfully so that the average person can successfully utilize the computer without having to be a computer expert himself. The mining industry has recognized that computing technology has evolved to a point where it can be applied successfully to assist in improving productivity. Since equipment downtime is one of the major reasons for lost production, the Kennecott Minerals Company has developed a comprehensive maintenance information system which now assists the maintenance department in minimizing equipment downtimes. This paper discusses the primary features and functions of this system, the state-of-the-art technology that has been applied, and the benefits that resulted from using this system. Programs to support mobile equipment maintenance scheduling, which currently are under development, are reviewed and a summary of future applications is given.

Jan 1, 1982

By H. Zhu, A. G. Journel

Qualitative and interpretive information as obtained from geological and/or geophysical studies, in addition to precise measurement, is incorporated into the estimation process through an indicator variable. The indicator conditioned estimator is formulated as a cokriging, and its expression is data value dependent as opposed to that of the traditional kriging estimators. The solution of the dual cokriging system provides simultaneously an estimate of the unknown and an estimate of the conditional probability that the unknown belongs to a specific population or class. Being an unbiased and minimum-error-variance estimator by construction, the indicator conditioned estimator is better in the least square sense than the ordinary kriging estimator because it uses additional information carried by the indicator data. A case study using a large reference database is presented; the indicator conditioned estimates have a smaller conditional bias and a smaller error variance than the ordinary kriging estimates. The results also showed that the indicator conditioned estimator is more efficient for selection in mining.

Jan 1, 1990

By Y. C. Kim, I. S. Roditis, P. K. Medhi

The strongly skewed grade distributions and the need to estimate the local recoverable reserves in a selective mining environment are the two problems that ordinary kriging (OK) cannot easily handle. With the recent introduction of the non- parametric, distribution-free technique of indicator kriging (IK), the above problems can be solved. This paper describes the result of performance evaluation of IK in an open-pit gold-silver deposit. For performance evaluation, the predictions of local recoverable reserves using IK were compared with the actual reserves based on blasthole information. The IK estimator, although a bit optimistic (or overestimating), performed very well in predicting the total recoverable ounces of gold from each panel on a test bench. The OK estimator was also used to try to predict local recoverable reserves, by treating each panel as either waste or ore, depending on the panel's average grade. Under this criterion, OK was found to be quite biased and pessimistic (or underestimating).

Jan 1, 1988

By Kenneth R. Miller

ThunderBasin Coal Co. has two mines located in the southern portion of Wyoming's Powder River Basin - the Black Thunder Mine and the Coal Creek Mine. Both are located 60 to 90 kin (37 to 55 miles) southeast of Gillette. The mines are principally located on federal coal leases acquired in the late-1960s. Development plans for the Black Thunder Mine focused on dragline stripping. Environmental considerations, however, made truck-shovel stripping the method of choice when the mine opened in 1976. In 1981, the Coal Creek Mine opened as the first dragline mine in the Gillette area of the Powder River Basin. The regional terrain is flat-lyimg with occasional clinker-capped hills. The mines are located on the Wasatch and Fort Union Formation contact. The coals are Paleocene in age. The deposits are structurally simple, dipping gently to the west. The seams are thick and are classified as sub-bituminous-C. The Black Thunder Mine, with its 21-m (70-ft) 'hick seam, is strategically located in the center of the highest heat value mining area of the southern Powder River Basin.

Jan 1, 1993

By L. Vandamme, J. H. Curran

A fully three-dimensional hydraulic fracture propagation model, based on the Displacement Discontinuity Technique, is briefly described. Using this model, it is shown that the geometry of a propagating fracture is dependent on several factors, among which the fluid pressure distribution within the fracture plays an important role. The containment of hydraulic fractures is found to be dependent on stress and toughness barriers in the formation. Containment is also observed to be more effective with a decrease of the viscosity, pressure or flow rate of the injected fluid. The three-dimensional layout of the fracture is shown to have a definite influence on the width and pressure distributions within the fracture. The examples considered indicate the need for fully three-dimensional models, as complements to the commonly used two-dimensional and pseudo-three-dimensional models.

Jan 1, 1986

By Wan-Kyu Choi, Arpad E. Torma

The electrochemical reactions involved in a zinc sulfide flotation concentrate leaching with sulfuric acid in presence and absence of Thiobacillus ferrooxidans, as well as with ferric chloride - hydrochloric acid containing media, have been investigated. The cyclic voltammetric measurements revealed that many intermediate electrochemical reactions are involved in the zinc sulfide leaching. Using chronoamperometric and chronopotentiometric techniques, it was found that the leaching process is controlled by solid - state diffusion. The activation energy of solid - state diffusion process was determined by the Price's approach to be 21.3 kJ. The leaching mechanism is discussed in terms of solid - state properties (energy bondings) of the high energy gap solid zinc sulfide semiconductor and energy density states of redox systems of acidic leach media. A generalized model for the mechanism of zinc sulfide oxidation is present.

Jan 1, 1990

By S. Chander

Neutralization of acidity by addition of alkaline materials is a commonly used method to treat acid mine drainage. However, this procedure requires large amounts of reagents based on acid-base accounting. The potential use of organic additives in preventing or ameliorating acid mine drainage was investigated in this research. The tests were conducted in weathering columns using refuse samples from a coal cleaning plant. Both cationic and anionic compounds were tested. For a comparison, tests were made in the presence of limestone and lime. The results show that some of the reagents substantially retarded the rate of oxidation whereas others even enhanced it. The suppression of the rate of pyrite oxidation was ascribed to surface chelation. Formation of surface compounds prevented the pyrite particles from further oxidation. Such a treatment required only small quantities of reagents since the reaction was confined to the surface.

Jan 1, 1992

By Levent Ozdemir, Russell Miller, Fun-Den Wang

The full utilization of tunnel boring machines for excavation in medium hard and hard rock has been limited by insufficient knowledge of rock behavior under the action of mechanical cutters. An understanding of factors affecting the rock removal process will permit: (1) the more efficient design of tunneling machines, (2) the prediction of boring performance from geologic data and cores taken from the proposed tunnel alignment, and (3) an improved excavation rate, thus a lower tunneling cost.. The Colorado School of Mines, under the sponsorship of the National Science Foundation, is studying the effects of a number of parameters in regard to tunnel boring using both full and small scale laboratory tests, analyzing field boring performance and comparing the laboratory and field data. Results indicate: (1) the field boring performance can be reproduced in the laboratory, (2) the optimum spacing of cutters or optimum spacing to penetration ratios may be found in laboratory testing, (3) it is promising to use small core samples and laboratory testing to predict field machine performance and (4) effect of joints on boring rate is significant and should be included in predicting tunnel boreability.

Jan 1, 1974

By P. N. Thompson

The past few years have seen the introduction of mini-computers on an increasing scale at collieries in the British coal industry. These are being used for controlling underground transport systems, coal preparation plants and fixed plant (pumps etc.); and for monitoring the mine environment and face operations.. A separate mini-computer (termed a primary computer) is dedicated to each of these functions. The overall system under which these computers operate is a common one which is applicable at all collieries. The information collected by the primary computers, other than that required for immediate control, will be fed to a secondary computer for analysis and processing. This overall concept, called MINOS. (MINe Operating System) is being developed by the National Coal Board's Mining Research and Development Establishment (M.R.D.E.). Eventually most of the data required by the system will be captured automatically. For example, the fact that a delay has occurred on a face, together with the duration of that delay, will be detected automatically via transducers link linked to a primary computer. However, the reason for that delay will, in all likelihood, have to be recorded manually. Such a system is currently under development with the first trial installations now being made.

Jan 1, 1979

A series of laboratory based push and pull tests were carried out to investigate how surface profile influence the load transfer mechanism of bolt/resin interface. Tests were carried out in both 75 mm and 150 mm long steel sleeves. Three types of bolts were examined, they were bolts most commonly used for strata reinforcements in underground coal mines in Australia. The bolts had near equal core diameter but of different profile configurations. The change in the length of the encapsulation sleeve was examined in light of the small number of profiles encapsulated effectively in short 75 mm long sleeves. The results showed that peak loads and displacements were directly related to the height and the spacing of the bolt surface profiles. Profile spacing appears to have greater influence on load transfer capacity than the profile height.

Jan 1, 2006

By Mary B. Ansari

The literature of mine ventilation is very diverse in nature, widely interdisciplinary, and extremely international in scope. Important references are found in indexes, abstracts, government documents, technical reports, journals, conference and symposia proceedings, and monographs. In this decade computer searches of the literature have greatly aided researchers in finding needed items. There is, however, no convenient summary of recent English language literature in coal and non-coal mine ventilation. This paper attempts to fill that gap in the literature. Because of the worldwide provenance of the subject and the attendant publication deluge, this paper covers only current English language publications on ventilation. The writers have examined the field's English language abstracts, indexes, bibliographies, periodicals, technical reports, books, and symposia and conference, proceedings. The survey also considers the field's most important bibliographic data bases. It should be noted that addresses for many of the literature sources listed in the paper are given in the section on literature and data base information sources.

Jan 1, 1980

By Ruoming Gong, Arindam Samanta, Ragula Bhaskar

Three studies conducted at the University of Utah relating to the effect of scrubbers on face airflow patterns, the resulting dust exposure of operators and the development of a throat scrubber for continuous miners are summarized in this paper. The first study involved full-scale laboratory tests to determine the potential dispersion patterns and transport of dust at a continuous miner face, using different ventilation configurations and a scrubber. Concentration maps were developed and potential exposures at operator positions were examined. The second study involved the development of a 3-D numerical model to predict airflow patterns generated by a scrubber at a continuous miner face. The model was designed to evaluate the role of various face parameters on airflow patterns at a miner face and to complement the full-scale testing. The third study involved the design and fabrication of a low profile hydraulically powered continuous miner throat scrubber. The scrubber uses three hydraulic motors and small diameter fans to draw about 3000 cfm (1.42 m3/s) of air and uses a flooded bed scrubber to filter dust particles.

Jan 1, 1993

By Satya Harpalani, Xue Zhao

This paper discusses the results of an experimental investigation to study the release of methane in coalbeds. Absolute porosity of coal samples was first determined experimentally. Following the porosity measurement, adsorption/ desorption tests were carried out to determine the gas content of coal and the rate at which it is released. Finally, micrographs were obtained using electron microscopy and the use of a physical model, developed to explain the gas flow behavior of coal, was justified. The results of this study indicated that the measured absolute porosity of the coal sample was between 5 an 6%. This was significantly lower than the porosity estimated by comparing the micrograph area occupied by the pores and the area of observation for several micrographs, suggesting that coal has a large number of pores with a very small volume. The micrographs also clearly indicated that coal has a large interconnected network of cleats and microfractures. The adsorption/desorption experiments showed a hysteresis between the adsorption and desorption isotherms. Also, the rate of desorption was found to be strongly dependent on the particle size of the specimen.

Jan 1, 1989