Search Documents

By David T. Swanson

The term "pressure tunnel" in the broad sense includes all hollow spaces, aligned along an axis and surrounded by rock, which are suitable for pressurization. In particular, this category includes: • horizontal or slightly inclined water pressure tunnels; • vertical or inclined pressure shafts; • pressure chambers or shafts of surge chambers; and, • compressed air storage tunnels. The main problems in the design and construction of pressure tunnels result less from their length or size than from the requirement for watertightness and, dependent upon this, reliability in operation and economy in construction. Where the lack of sufficient overburden does not permit the rock to accept the internal pressure in the tunnel, or where this pressure is so high that the watertightness is in doubt although the stability of the tunnel shell is not in question, a pressure tunnel must nevertheless be reinforced. Surge chambers, pressure tunnels and tailraces which are subjected to relatively low internal pressure, usually not much in excess of 1.5 MN/m2, are eminently suitable for construction in post-tensioned concrete. Pressure shafts, which as a consequence of the high water head are subject to a considerable maximum service pressure, are usually lined with a steel tube, a considerable proportion of the internal pressure being transmitted to the rock by backing concrete. TYPES OF LINING FOR PRESSURE TUNNELS In general, the type of lining will depend upon the nature of the rock. As a result, pressure tunnels usually are not uniform in con-

Jan 1, 1981

By Heinrich H. Becker, Vladimir L. Konyukh, Sergey P. Koltsov, Valery A. Davidenkol

Ramifide conveyor transport of the biggest russian coal mine "Raspadskaya" is simulated by Petri nets. There are 6 longwalls with accidental output. 12 belts, and 5 transfer bunkers at this mine. It is necessary to coordinate transport links for recon- structed conveyor system. Many tasks were solved by dynamic simulation, such as estimation of transport lateness, influence of transfer bunkers on an unevenness of total coal flow, maximum filling of each bunker, maximum time of main conveyor refusal, co-ordination of unloading for dependent bunkers, choice of main conveyor. The problem of mine-wide conveyor transport animation for dispatcher is formulated in reference to mine "Komsomolets". OBJECT OF SIMULATION The biggest russian coal mine "Raspadskaya" is situated on a south part of Kusnetski coal basin (West Siberia). One mines about 20.000 tons of coal out of flat seams by 2.2-4.5 m thickness in a day. There are 6 fully- mechanized longwalls by output 720- 3600 tons in a shift in mine. Coal haulage to surface is carried out by 12 belts having 1.6 - 4.3 km length. For a smoothing over un- evenness of coal flows 5 transfer bunkers to 300 tons were intro- duced. The designed conveyor system is divided into two parts (Figure 1). In the upper part some coal from Face 1 comes through belt road C, into transfer bunker 8,. From the opposite side that bun-

Jan 1, 1996

By Ellis L. Armstrong

Welcome to Chicago and to the first North American Rapid Excavation and Tunneling Conference. It is a great privilege for me to serve as the Chairman of the Executive Committee of such a Conference. We are here because of the rapidly mounting interest of technicians the world over in turning the potential use of underground space into sensible and economical benefits to people. This Conference certainly provides a major forum of international importance and scope for the exchange and dissemination of up-to-date knowledge on the technology of underground excavation and tunneling. The discussions will also surely delineate the immediate and longterm challenges we must approach in multidisciplinary force. We must exercise leadership in the problems we are trying to solve. Your program shows the breadth of the technical discussions which are going to be underway here during the three days of this Conference. I am not going into technical aspects or detailed discussions of the many uses to which underground space may be devoted. I also will leave to the technical meetings the outline of the state of the art. But I do want to tell you of the progress being made in channeling the expertise of many of the world's foremost authorities on rapid excavation and tunneling to consider the problems, laying the ground work for needed research, and provide the leadership in converting unused subsurface potentials to improve the quality of life. This first conference of its kind for North America is sponsored by the American Institute of Mining, Metallurgical, and Petroleum En-

Jan 1, 1997

By William P. Barnett

In 1988, the US Department of Energy's (DOE) Pittsburgh Energy Technology Center identified three coal cleaning options for achieving flexible environmental control strategies aimed at reducing energy-related SO2 emissions. These are selective agglomeration, advanced froth flotation and advanced cycloning. Each relies on maximum liberation of pyrite and other mineral matter through feed coal comminution to fine and ultrafine sizes. The National Energy Strategy (NES) and the Clean Air Act Amendments (CAA) of 1990 are examples of the nation's commitment to a clean environment. The need to use the nation's energy resources in an environmentally sound manner presents critical challenges and opportunities for coal preparation during the next decade, particularly regarding the control of SO2 emissions. The principal challenge is the development of cost-effective coal preparation approaches for sulfur removal beyond currently achievable levels. Opportunities are provided in the form of incentives associated with a novel system of SO, allowances and a policy environment based on the proper functioning of familiar market forces. An allowance, as defined in Section 402(3) of the Amendments, is "an authorization ... to emit ... one ton of sulfur dioxide." To achieve the objective of the Clean Air Act Amendments, SO, emissions will be eventually capped at 8.12 Mt (8.95 million st) annually by controlling the number of allowances issued nationally. By permitting allowances to be bought and sold once issued, the law encourages "overcompliance" as a source of profit for owners of excess allowances. Many details concerning the administration of allowance trading are not yet written.

Jan 1, 1992

By K. Chandrasekaran

Carbon-in-leach (CIL) is conventionally used in gold processing operations when preg robbing components are present in the ore. The CIL process is becoming attractive even in other situations when preg robbing is not a factor. This article discusses the situations in which the CIL circuit can be applied. The results of leach-carbon-in-pulp (CIP) and CIL circuits at Newmont Gold's Mill No. 2, No. 4 and No. 5 are presented for comparison: Mill No. 4 was initially designed for a throughput of 4.1 kt/d (4500 stpd). It is presently operating at an average throughput of 6.6 kt/d (7300 stpd) without significant changes to the original design. The design considerations of the Mill No. 4 CIL circuit are discussed. The design of any processing facility represents a series of decisions. The final design options should ultimately be resolved based on economic as well as technical considerations. Every design decision represents some sort of compromise. From the designer's view point, these decisions are made with the conviction that the final product represents the most prudent long-term expenditure. The design throughput rate is a decision reflecting a maximum return for the capital and operating costs that the plant will incur over the life of the mineral resource. The result is a plant that is not operator proof or maintenance free because it would be too costly to build. At some point, the incremental increase in the level of capital expenditure would not adequately compensate for the lower

Jan 1, 1991

By Paul Saxton

INTRODUCTION AND SUMMARY This short paper deals with the history of the Nickel Plate Mine from 1898 to 1987, with the major focus on the time period 1984 to 1987. Operations from 1898 to 1955 are reviewed in a cursory manner with the emphasis on some interesting points in the early 20th century. A review of the major exploration work carried out in 1984 to 1987 is presented and the process of moving the project through feasibility, government permitting and construction is described. The Hedley gold camp is situated approximately 40 kilometres east-southeast of Princeton, in southern British Columbia. The area has had a long history of gold mining and between 1902 and 1955 approximately 1.5 million ounces of gold were won from several mineralized skarn orebodies. Most production came from the Nickel Plate and Hedley Mascot mines. AN EARLY TO MID 20TH CENTURY SUMMARY The Nickel Plate is one of the oldest mines in the province. The mine had operated from 1904 to 1930 and, after a period of shutdown, from 1934 to 1955. The mine was revived in 1967 for exploration and. will resume production during the first half of 1987. In the first period the Yale Mining Company and Daly Reduction Company operated for six years and Hedley Gold Mining Company for twenty-one. In the second period the mine was operated by the Kelowna Exploration Company Limited and Kelowna Mines Hedley Limited for twenty-one years. In the present period the mine has been revived by Mascot Gold Mines Limited.

Jan 1, 1987

By P. Somasundaran, D. R. Nagaraj, Jing Wang

Polysaccharides have been widely used as depressants in mineral processing for decades. They constituent one of the most abundant family of biopolymers. However, only a small number of them have been used by industry so far because of a general lack of understanding of interactions between these polymers and minerals. In this work, adsorption tests, electrophoretic mobility measurements, microflotation and fluorescence spectroscopic tests were performed along with computer simulation to explore the mechanistic aspects of guar gum adsorption and conformation on talc as a function of relevant variables such as ionic strength, pH, solvent composition and polymer molecular weight. From microflotation tests, it was found that talc hydrophobicity decreased markedly due to the adsorption of guar gum even at very low concentrations and reached a plateau below moximum adsorption. Guar gum adsorption on talc was found to be not affected significantly by changes in solution conditions such as pH and ionic strength, ruling out electrostatic force as controlling factor for adsorption. Fluorescence spectroscopic studies showed no evidence of the formation of hydrophobic domains at talc-aqueous interface. Also urea, a hydrogen bond breaker, reduced the adsorption of guar on talc. All of the above results suggest that one of the main driving forces for guar adsorption on talc is hydrogen bonding in preference to electrostatic or hydrophobic force. This information should help toward designing reagents of optimum molecular architecture for efficient depression, dispersion or other such surface modification of particles.

Jan 1, 2005

By Lynne Chastain

The Eastern Shoshone and Northern Arapaho tribes of the Wind River Indian Reservation, Wyoming are interested in developing their industrial mineral resources. The U.S. Bureau of Indian Affairs (BIA), Division of Energy and Mineral Resources (DEMR) is assisting the tribes in evaluating the potential of their industrial mineral prospects for development. Gypsum occurs on both sides of the Owl Creek Mountains in the basal portion of the Jurassic Gypsum Springs Formation. The gypsum resources that are being evaluated crop out along the northern flank of the Owl Creek Mountains in the Sweetwater basin, a small topographic sub-basin of the Big Horn Basin. From October 1998, to April 1999, DEMR personnel mapped, sampled, and drilled the southcentral butte within the Sweetwater basin. Samples were analyzed for free and combined water, and major mineral oxides to determine gypsum purity. Gypsum purity averaged 93.6 percent for surface samples and 95.1 percent for drill core samples. The basal portion of the Gypsum Springs Formation is comprised of several beds of gypsum up to 9 feet (2.7 m) thick separated by 0.5 to 2.0 foot (0.15 to 0.61 m) thick lenses of siltstone and limestone. Overall gypsum in the formation ranges from 35 to 90 feet (11 to 27 m) in thickness. A resource of approximately 7 million short tons (st) (6.4 million metric tons [mt]) has been identified.

Jan 1, 2001

By George Aul, Richard Ray

Short-hole horizontal degasification systems have been utilized in Island Creek's Virginia Division mines since 1986. These systems remove methane from the coal seam in advance of longwall mining. Without an in-seam methane drainage program, methane liberation rates from the longwall faces may exceed 0.47 cu m/s (1,000 cfrn), requiring 47 cu m/s (100,000 cfm) of air for adequate dilution capability. Optimization of the degas systems has enabled methane liberation levels and the associated ventilation requirements on the longwall faces to be reduced by 50 to 80 percent. Since the inception of the first degas system at the Virginia Pocahontas No. 6 Mine, Island Creek has developed an overall methane drainage program designed to maximize gas production and minimize ventilation requirements for methane dilution. Gas production from the degas systems is affected by four main design criteria: (1) hole location, (2) hole length and spacing, (3) collection system capacity, and (4) time available for drainage. Drilling equipment and materials for the gas collection system are selected to meet the necessary criteria while minimizing manpower requirements. Benefits gained from reducing methane liberation rates from the longwall faces are fourfold: (1) improved safety due to lower methane concentrations in the face area, (2) fewer production delays caused by excessive methane concentrations, (3) lower fan operating costs resulting from reduced air requirements, and (4) enhanced worker comfort resulting from lower air velocities and less dust generation.

Jan 1, 1991

By Edwin J. Connell, O&apos

Investment in mining and related process facilities will be more costly and complex in the 1980s than ever before. Interest rates and inflation are soaring; regulations are expanding; and in order to achieve economies of scale, plant facilities and mines are getting larger. As the pace quickens, the time/cost circuit closes around the resource owner or developer. Larger modern projects cost more money and take more time to build. The longer it takes to bring a project onstream, the more it costs in interest, escalation, and lost production. One solution to the time/cost squeeze is to take advantage of systems developed by major contractors serving the mining industry. These contractors have been serving clients in planning and executing large and small projects for many years. They have developed systems which, if applied at an early point in the project's life, can be a significant benefit in development of mineral resources. The systems involve performance of feasibility studies, economic evaluations, and the project installation itself. First the Feasibility Study Feasibility studies can minimize risk through systematic evaluations while progressing toward the ultimate objective-an operating plant. Normally, studies are initiated with a minimum amount of specific information and a maximum number of as¬sumptions. Through the course of the study program, assumptions are continuously confirmed, refined, or rejected by facts until a sound basis for decision is available. High on the list of cost effective tools for evaluation is the use of a geostatistically derived sampling program that provides a highly accurate ore reserve estimate for economic evaluation. When a predetermined sample of data from the drilling program and bench-scale or pilot-plant tests are received, a detailed feasibility study may be started. This study can involve design of the mine,

Jan 10, 1980

By V. Scovazzo

Cost-effective underground mine configurations have been designed in highly fractured rock masses where the stone possesses a high material strength. A limestone mine in the eastern United States is used to demonstrate procedures for the geotechnical design of one such operation. The mine discussed is located in both limbs and the axis of a recumbent fold that fractured the rock mass. In a highly fractured rock mass, where the host rock has high strength, a design can be developed to alleviate intact rock failure. This is possible because in most cases as the stress levels needed for intact failures are approached, the stresses are quickly dissipated due to movement along discontinuities, which represent planes of weakness. As a result most underground failures in highly fractured rock are due to sliding or toppling. Even when intact rock fails in a highly fractured rock mass, it is the movement along an existing joint or other weakness plane that often initiates or causes this failure. It is therefore important to obtain the characteristics of weakness planes that are the discontinuities within the mass. The required information on weakness planes, geology, and strength of materials is discussed and recommendations for obtaining this information are presented. A discussion is provided on failure modes and the use of developed information for their evaluation. The impact on geotechnical design is demonstrated through pillar sizing procedures; however, this approach can also be applied to mine roof and pillar foundations.

Jan 1, 2004

By Gary F. Rajala, Bruce R. Greenwood

INTRODUCTION The Empire Mine is an iron ore mining, concentrating and pelletizing facility operated by The Cleveland-Cliffs Iron Company in the Upper Peninsula of Michigan. Owners of the mine are Inland Steel, LTV Steel, Wheeling-Pittsburgh Steel and Cleveland-Cliff s. The orebody is a fine-grained, low grade iron formation with magnetite as the primary constituent. Also present are iron carbonates, iron silicates, chert, hematite, goethite and quartz. The original six concentrating lines were started in late 1963. Successive expansions of ten lines in 1967, five lines in 1974 and 3 lines in 1979 have resulted in Empire reaching a present annual capacity of 8.0 million long tons of pellets. The Empire flowsheet was developed over several years of laboratory bench testing, pilot plant testing and testing of a full-scale primary autogenous grinding circuit. Since the original flowsheet was established, modifications have been made based on pilot plant and full-scale plant tests. The present flowsheet for three sections of the concentrator consists of one stage of crushing, two stages of closed circuit autogenous grinding, two stages of magnetic separation, one stage of hydraulic concentration and two stages of flotation (rougher and scavenger). The flowsheet for the fourth section of the concentrator (Empire 4) is the same as the first three sections, except a crusher has been added to crush excess pebbles. The Empire 4 flowsheet appears in the at- tached figure. PRIMARY GRINDING CIRCUIT FLOWSHEET Empire has a total of 24 individual grinding lines. However, at the present time, Line 1 is not being used for processing crude ore. The primary mill on Line 1 is now grinding flux stone for fluxed pellet production and the secondary mill is being used as a ball mill to grind rougher flotation tailings prior to a scavenger flotation circuit.

Jan 1, 1992

By M. J. Friedel

The scale-dependent hydraulic properties in a fractured porphyry copper oxide deposit are investigated for relevance to In Situ Leach Mining (ISLM) design. In most well field designs, mine operators assume that hydraulic properties represent a continuous spatial function, or continuum. The problem, however, is that the representative elemental volume, the volume over which hydraulic properties are described as a continuum, is a domain (if it exists) that occurs between end members representing varying degrees of heterogeneity. At the Cyprus Casa Grande mine, transmissivity fluctuations are spatially correlated. This suggests that, at the scale of ISLM, the hydraulic process is heterogeneous, and a typical continuum representation is inappropriate for design. Alternatively, a conditional stochastic approach using the Simulated Annealing (SA) technique is deemed useful for the imaging of heterogeneous hydraulic properties. Specifically, SA preserves transmissivity extremes and spatial complexity, both necessary for accurate conditioning of a flow simulator. Also, the stochastic continuum approach provides an avenue whereby uncertainty (or risk) may be addressed. Currently, the SA weaknesses are that it is computationally time consuming and that uncertainty may increase when simulating under conditions of statistical isotropy. Recognizing that ISLM exerts a dynamic influence on hydraulic properties with time, the mine design should be re-evaluated at intervals throughout the evolution of the leaching process.

Jan 1, 1994

By Francesco Chiappalone, Marco Invernizzi, Franco Gasperin, Fabrizio Fara

As part of the Ship Canal Water Quality Project, 2.7-mile Combined Sewer Overflow tunnel is excavated with a 21.5-foot diameter EPB Tunnel Boring Machine. Due to the difficult geological and hydrogeological conditions, the tunnel is excavated maintaining a ground support pressure between 1 and 3 bar imposing significant challenges to the projects. The first part of the paper describes the general characteristics of the project while the second part focuses on the challenges and technical details of the pressurized breakthrough that took place in a deep shaft excavated in urban environment as part of the project.

Jun 23, 2024

By J. Siege1, R. S. Popielak

A computer model was used to simulate the effect of leakage through confining beds on a hypothetical in situ leach operation in an aquifer with a thin mineralized section. The simulations were used to assess economic and potential environmental implications of leakage on an in situ leach operation. Four scenarios were modeled - three representing cases with different degrees of confinement, and the fourth representing a stratified ore zone under a low degree of confinement. The model simulated the travel path and travel time of lixiviant given the hydraulic conditions prescribed in each scenario. The results show that the travel path and travel times vary by about 10% for confinement ranging from nearly impermeable (essentially no leakage) to an extremely low level (thin confinement with a permeability about equal to that of the aquifer) for isotropic aquifer conditions. The aquifer thickness contacted by the lixiviant varied from 85% to 90%. Horizontally, 55% to 60% of the aquifer was contacted. The flow paths in the stratified aquifer were reduced in the vertical direction and expanded horizontally. Forty- five percent of the aquifer thickness was contacted vertically with 88% contacted horizontally. Break- through time for lixiviant traveling at mid-depth of the aquifer increased two times when the leakage was increased from nearly zero to a value representative of thin and highly permeable confinement. Leakage affects the economics of in situ mining by (1) increasing the time required to leach out the ore, and (2) increasing the thickness of the ore zone aquifer to be restored. The potential for environmental impacts appears to be minor. In all four simulations, the lixiviant did not contact the confining strata. Restoration would be limited to cleanup of the ore zone aquifer within the thickness contacted by lixiviant and within the radius of the lixiviant that traveled farthest away from the production cell.

Jan 1, 1988

By William J. Maloney

OVERVIEW Blind drilled shafts are becoming increasingly popular, particularly in the Appalachian coalfields, as a secondary and sometimes primary means of ventilation. The reasons for the rebirth of the blind shaft are mainly due to it's economics, timeliness, safety characteristics and inherent independence from underground operations. Historically blind drilling has been used to a limited degree in hard rock and tunneling ventilation. With the recent advances in cutters, bit design, equipment and lining systems, particularly in the Appalachian coalfields, blind drilled shafts are once again the shaft construction technique of choice to the educated ventilation specialist. [ ] HISTORY OF BLIND DRILLING Blind drilling has it's roots in numerous places, including the Nevada Test site, the coalfields of Appalachia and Germany along with the uranium mines of Arizona. Early technology was developed using a variety of equipment mainly of oilfield origin with oilfield drillers entering the industry on a project basis only to "pull in their horns" and return to the oil patch. Shafts completed by oilfield equipment range from the shallow 5' and 6' lined shafts on the Nevada test site to two (2) 10' lined, 730' deep shafts in Alberta for heavy oil development. Several of these shafts were completed to extraordinary depths with the record being a 90" diameter, 6,150' deep shaft being completed in the Aleutian Islands of Alaska in 1969. EQUIPMENT Oilfield equipment is still being used on the Nevada test site but elsewhere specialized blind hole equipment has been developed to enhance the efficiency of particular applications. Where steel liners are required the A-leg derrick with a simple hoist and rotary system is used. The largest user of this type equipment in the world is the former USSR where blind drilling for mine ventilation is the norm. On applications where trip time and cutter changeout are a priority, top drive hydraulic rigs have been developed which are highly automated, efficient and mobile. These rigs are particularly well suited for tunneling applications where shafts are shallow and sites are usually tight.

Jan 1, 1993

By H. J. Sohn, S. G. Doo

A systematic study was carried out to investigate the reduction reaction mechanism of oxygen on pyrite surface using electrochemical techniques. The polarization curves showed two distinct regions, the Tafel region for superoxide formation and limiting current region for diffusion of dissolved oxygen to form hydrogen peroxide. These results were confirmed with a-c impedance measurements.

Jan 1, 1990

By George Wilson

As the economic and environmental attractiveness of conveying coal and ore slurries by pipeline increases, greater attention has been given to designing and selecting components for these pipeline systems. Pumps are one critical element in pipelining. Pumping slurries is a particularly arduous task, calling for special design and construction. The first article in this two-part series describes some factors to consider when selecting pumps to resist abrasive wear.

Jan 9, 1981

By P. R. Taylor

This work is concerned with the extraction of refractory metals using an electro-reduction process, in which a molten oxide melt, instead of halide, is used as the electrolyte. The process may provide an alternative method of producing refractory metals from their ores through use of a reverse-polarity direct current (DC) plasma arc heating process. In such a process, the plasma torch itself acts as an anode, and resulting liquid or solid product metals work as a cathode, whereas the molten oxide melt plays the role of an electron transfer layer. The focus of this study is: the electro-reduction of scheelite; vanadium pentoxide; and chromite. For the vanadium pentoxide, the proposed melt is mainly composed of CaO-V2O5/Li2O-B2O3-V2O5or FeO-CaO-SiO2-V2O5-Li2O with the addition of other alkali and alkaline metal oxides. In the case of scheelite ore, the SiO2-CaO-Li2O-WO3system is used as melt and metal aluminum or nickel could be used as a collecting media. As for the reduction of chromite ore, SiO2-CaO-Cr2O3-Li2O system with trace amount of CaF2is used as the melt. As a demonstration, chromium was successfully produced at a laboratory scale through the plasma driven electro-reduction process. One of the studied slags had a composition of 13.8% CaO; 4.9%CaF2; 36.4% Cr2O3; 6.9% Li2O; and 38.0% SiO2. Two observations are significant in this laboratory scale study. The first one was that the amount of Cr2O3and FeO, which were predominantly electronic conductors in the oxide melt, greatly affected the conducting mechanism of the melt. With high concentration of Cr2O3and FeO in the melt, the current efficiency was fairly low. In this case, chromium was found to be barely reduced because of electronic conducting mechanism. For example, with initial slag of 60% Cr2O3, no chromium was found reduced. With low concentration of Cr2O3and FeO in the studied melt, typically no more than 30% Cr2O3, it was observed that chromium was readily reduced due to the dominant ionic conducting mechanism. The second observation was that the addition of SiO2tothe melt helped to make the oxide melt more ionic, which was apparently desirable to the molten oxide electrolysis. However, high content of silica had a negative effect on the fluidity of the melt. This was resolved by adding trace amounts of CaF2to the melt. Therefore, by judicious selection of oxide melt, refractory metal oxides might be dissolved into it and yet the melt itself retains the required ionicity. A reverse-polarity DC plasma driven molten oxide electrolysis may prove to be a viable alternative route for the extractive metallurgy of refractory metals.

Jan 1, 2003

By Arthur F. Moss

Smallbore tunnels in urban environments often present more technical and managerial problems than major large diameter schemes carried out for transportion, water supply and hydro-electric facilities. The 1.8 km Bath scheme was designed for construction in tunnel using the pipe jacking system. Unforeseen ground conditions meant other techniques were needed during construction. The paper describes the problems encountered and how they were overcome.

Jan 1, 1981