Search Documents

The leaching of gold and silver by ammonium thiosulfate solutions in the presence of copper has been actively studied in recent years. Newmont Gold Company has successfully tested the ammonium thiosulfate for gold extraction following biooxidation pretreatment of low grade refractory carbonaceous/sulfidic ores. In this paper, the chemistry of the copper catalyzed leaching process is reviewed. Factors affecting both the leaching reactions and the stability of the lixiviants are reviewed and discussed from a solution chemistry perspective.

Jan 1, 1996

By R. E. Utting

INTRODUCTION Until recently, gamma doses had been largely ignored in Ontario uranium mines. This has been due to the assumption that these doses are small and have been more or less unchanged with time and hence their effects have been included automatically in the epidemiological studies that led to the establishment of radon daughter exposure limits. This assumption had to be challenged for two basic reasons. The first was that radon daughter exposures to miners have been progressively reduced over the years due to improved ventilation and ever more stringent regulations, while gamma exposures have presumably remained relatively unchanged. Therefore it must be assumed that the ratio of gamma to radon daughter exposure has gone up. The second reason is more philosophical. It is clearly inappropriate to make judgements on the significance of a potential industrial hazard when the magnitude of that hazard has not been fully assessed. Having decided that some sort of assessment of gamma exposures to uranium miners must be made, it was than necessary to determine how this should be done. Several options were available, for instance: (i) Wholesale personal gamma dosimetry for all mine and mill workers, (ii) Personal gamma dosimetry only for those workers suspected of receiving the higher doses, coupled with area monitoring to estimate the exposures of other workers, (iii) Area monitoring coupled with dose rate times time calculations for all. This would correspond to the generally prevalent method of assessing radon daughter exposures. It was argued that since radon daughter exposures are the major radiological hazard in uranium mines, to invest resources for assessing a lesser hazard to a greater degree of precision was not cost effective. (iv) Since gamma dose rate is related to ore grade, individual doses could be assigned from knowledge of work location and ore grade. Before deciding which of these options would be most appropriate, it was necessary to have some idea of the magnitude of the problem. Very few data were available in the literature and with the exception of a few spot dose rate measurements, and the results of a few gamma dosimeters issued to selected individuals by some of the mining companies, nothing was available. A rule of thumb of obscure origin is often quoted within the industry indicating that gamma dose rates underground will be about 0.25 mR/h per lb/ton or 5 mR/h per % U. This had been used by some to justify neglecting gamma radiation at least for ore grades of the order of 0.1% or 2 lb/ton, on the grounds that gamma dose rates would be of the order of 0.5 mR/h and therefore give rise to annual doses of only about 10 mSv (lrem). That is, it was assumed that gamma radiation was of limited concern compared to the hazard associated with the inhalation of radon daughters. We were thus faced with the situation of just assuming that no regulatory limits were being breached. This situation could not be allowed to continue. A program was initiated to investigate the gamma doses absorbed by uranium miners in three mines in Ontario, and extensive gamma surveys were conducted in the Quirke 2 mine of Rio Algom Ltd, Elliot Lake; Denison Mine, Elliot Lake; and Agnew Lake Mine, Espanola. Negative reaction was received from several mine company officials to the possibility of all miners being required to wear personal gamma dosimeters due to the logistical difficulties involved, and therefore part of the project was aimed at determining if a reliable correlation between gamma dose rate and ore grade in the work location could be deduced, in order that dose rate times time calculations might be used for gamma dose assessments. The results of these programs provided evidence that the gamma dose for some employees in the three mines investigated may be a significant fraction of the current maximum permissible annual dose of 50mSv (5 rem). When combined with radon daughter exposures in the manner recommended by the ICRP at their 1980 Brighton meeting (ICRP 80) the results indicated that some individuals will come close to the resulting limit and may even exceed it. The results also indicate that is probably not feasible to develop a reliable formula for

Jan 1, 1981

By A. T. Sapulek, C. S. Özveren, D. W. Dixon

The prediction of underground methane emission from longwall coal faces has been extensively researched for a number of years and numerous prediction methods have been devised. Many coal mines employ sophisticated environmental monitoring equipment which generates large amounts of data including, methane concentration, air velocity and barometric pressure. Presently this information is mainly used only to indicate alarm and danger levels of the monitored data for management purposes, however, the potential uses of this data are enormous[1]. This information could be used to good effect within a production/methane emission strategy as detailed in a previous paper[2]. The paper presents a practical application of artificial neural networks to underground methane prediction. Data on methane concentration and coal production has been obtained from an underground coal mine. The data is used in a neural network architecture and forecasts of methane concentration have been obtained. The forecasts are examined and there is a discussion of the potential use of the predictions from neural networks in the field of mining production control.

Jan 1, 1995

By K. Gorazda

The population growth, urban and industry development cause the increased pollution with different substances, which contain phosphorus. It contributes to the increased demand for its compounds, increasing the use of its natural resources, which is considered to be the most accessible source. The forecasts regarding the world natural reserves of phosphorus deposits are saying that more than 50% of resources used currently will be exhausted within next 60-70 years (Steen, 1998). European Union formulated its goals regarding the waste management in 1990. Its main rules include prevention of waste generation, recycling, reuse of waste as the raw materials in technological processes, separate collection and optimization of final removal. The phosphorus recovery from waste is realized currently in many ways: directly from the waste water stream in sewage-treatment plant, from the sewage sludge, from animal waste, industrial waste and other emissions from industry (Przewrocki et al., 2004). According to the rules of cleaner production the waste should be treated as the source of resources for the production of products with full value (Kowalski, 1998).

Jan 1, 2005

By Peter J. Tarkoy

The art of predicting rock excavating machine performance has become increasingly detailed and refined. Researchers using laboratory experiments and machine manufacturers using field observations have identified and defined mechanisms of failure, rock and tool interaction, and relevant design principles affecting them. Concurrently, practitioners have developed index tests which reflect rock properties relevant to machine performance. Empirical relationships between index properties and machine performance (penetration rate, cutter consumption, and machine utilization) have been established from past experience and are currently used throughout the industry. Contractors have used such relationships for estimating throughout the world. The detail in which geological, geotechnical, test, and project data, empirical relationships, and construction experience are utilized, is limited by time constraints imposed by the bidding period. To fully utilize all available data, methods of analysis, and construction experience, a simple computer program was developed for a microcomputer costing less than $7500. As a result, 1. machine performance predictions are detailed & reliable, 2. construction alternatives may be examined, 3. anticipated conditions & performance are graphically, documented & easily comparable to those encountered, and 4. results include a listing of assumptions & results of performance analyses & a graphic performance summary.

Jan 1, 1979

By R. L. Wiegel, G. R. Oswald

The processors of Florida phosphate rock face constraints similar to those of other mineral operations--leaner ore, more complex treatment schemes and a product which sells for a penny a pound. IMC Fertilizer is a dominant producer in this market with its current operation of five processing plants. An emphasis by their management in maintaining and improving plant performance has continued unabated for some 15 years. This has resulted in a commitment to the importance of routine automatic sampling of product and in process streams, the generation of reliable assay and size distribution data, the accurate measurement of process flows, and the computerized "rendering" of this information into weekly and monthly material balances which provide consistent measures of process performance. In addition, there has been a parallel program to monitor and improve the performance of flotation reagents and to evaluate process modifications or changes in equipment. This paper will describe the evaluation techniques that have evolved over this period and indicate how the historical data base is used to identify plant problems early and help in their solution.

Jan 1, 1991

By Norm Steenson

Rapid excavation includes rapid support and is the central theme of this paper. Over the last few years, enormous strides forward have been made in the excavation and material handling aspects of underground excavation. However, the technology necessary to support these rapidly created openings has lagged behind the other aspects. This paper would attempt to bring you up-to-date on the progress made in bringing ground support using shotcrete into the same productivity rates as the other cyclic operations. Shotcrete has become an acceptable material for temporary and permanent support for undergound openings. However, coarse aggregate shotcrete has been an expensive construction material. It has been confined in the main to difficult ground conditions where conventional methods of support have proved to be even slower and more expensive than shotcrete. There are two main factors influencing the productivity of shotcrete equipment. (1) Structural shotcrete as opposed to gunite requires 40% to 45% rock minus 3/4" in the mix design. The equipment to handle such aggregate content has been difficult to develop on a volume basis owing to the attritional nature of the material which causes intense wear problems on

Jan 1, 1974

By Louise H. Michaud

An interactive mine planning system that employs recent advances in 3D computer graphics capabilities and 3D geologic modelling to aid with the tasks involved in producing dragline mine plans was developed. As well as offering large potential saving in the time required to carry out the planning tasks, the system offers immediate visual feedback to the planning engineer. This can greatly aid in the conceptual understanding of complex geology and mine plans. The package incorporates the generation of a three dimensional Gridded Seam Model (GSM) as the basis for the development of the geologic database. This modelling method is capable of accurately representing rugged topography and multiple coal seams, including folding and faulting. The GSM is then integrated with an interactive graphics mine planning system in order to develop one model and one database for the generation of the mine design, the depletion of the coal resources and the movement of spoil material. The gridded structure of the model also provides the foundation on which all mine and spoil pile volumes are calculated.

Jan 1, 1992

By Slavko Ostojic, V. G. Hill

This paper reviews various bauxite classification schemes with respect to the differences in texture, composition and geological associations of the deposits. It demonstrates that a techno-economic classification, based on: a) associated rock type - lateritic versus karstic, b) content of aluminum ore minerals - gibbsite, boehmite and diaspore, and c) gangue minerals (iron oxides etc.) has a geological basis with natural cut-off points for the bauxite types identified. Thus, this scheme is seen as applicable to bauxite resources. It also provides a basis for their rational exploitation taking into consideration the long-term interests of both the bauxite producing and consuming countries. Against this background, the industrial mineral or non-metallurgical grades of bauxite are seen as localised and relatively rare occurrences. Their consumption should, therefore, be aimed toward the specific (hence more remunerative) products as indicated by the bauxite characteristics.

Jan 1, 1984

By Richard R. Klimpel

Part 2 of this article continues the discussion of a 10-year, multimillion dollar research and plant testing program on slurry rheology and grinding circuits. The first part of the article (ME, Dec. 1982) presented the basic concepts identified by the research and some laboratory test results. This section Illustrates typical Industrial scale test results and Identifies some industrial operating implications of controlling rheology by different methods. At least four controllable factors decide the rheological character of a slurry-slurry density or percent solids, particle size distribution, chemical environment, and slurry temperature. The second factor has two interrelated facets: the shape of the particle size distribution which controls packing behavior of the solids, and the fineness of the distribution. Finer particles increase interparticle forces and viscosity. As indicated in Part 1, during a given grinding test it is possible for all four factors to change. However, regardless of the particular settings of the four factors in a given test, if the resulting rheological character is either dilatant, pseudoplastic, or pseudoplastic with yield, the associated breakage rate is correlated with the current rheological character. It is obvious, for example, in batch grinding tests run at constant percent solids, that the second and third factors, where appropriate, are changing during grinding because size distributions are changing and the production of fresh surface area takes up unadsorbed chemical. Thus the corresponding rheological character change in batch tests with increasing grind time would be dilatant to pseudoplastic to pseudoplastic with yield. The degree to which this transformation occurs depends on the changing setting of the four factors over grinding time. In continuous grinding tests, one might logically expect that dramatic changes in any one of the four factors will be less likely to occur. It will be shown that continuous mill operations offer some unique opportunities to take advantage of possible rheological transformation by more direct operational control of the settings for the four factors. One extra observation noted in the rheological studies was the variability in the location and extent of region B (pseudoplastic behavior) for the various coals and ores tested. The location of region B was usually in the region of 45-55% solids by volume and was of the extent of 0-8%, or 2-11% with chemical addition. The corresponding increase in net production ranged from 0-10% in region B and 0-21% in region B&apos;. When region B is small or zero (no pseudoplastic character is exhibited) no increase in production will be observed and the use of chemicals is often marginal. There are several reasons for some materials exhibiting this quick transformation from dilatancy to high yield values often at surprisingly low percent solids by volume such as 30%. One condition identified was for materials containing high levels of viscosity-producing elements such as- carbonates or clays. A second condition documented was for materials that exhibited unusually fine primary fragment distributions (fine B1,; curves). This corresponds to materials having small y values of < 0.5. Such a slurry developed a yield value quickly during grinding because of the rapid buildup of fines. A related problem can be presented by materials exhibiting excessively coarse primary fragment distributions, y values > 0.9. Breakage of this type of material produces size distributions that give poor packing efficiencies even at long grind times, thus hindering the normal rheological transformation presented earlier. A final condition that can cause the occurrance of region B to be small or zero is when the media void volume filling of slurry is < 100%. Figures 5a and 5b use previously published data of this study to demonstrate the influence of solids loading and weight percent solids on the net production of taconite ore in a laboratory batch ball mill. In particular, Fig. 5a illustrates several trends not generally recognized until this study. They include these two: • Increased slurry density allows for increased solids loading before passing through the maximum in the net production curve where the fall-off is due to non first order breakage. • The use of rheology control chemicals such as GA-4272 allows this trend to be extended to higher slurry loadings with an increase in net production over any previous condition by keeping grinding first order. Figure 5b shows the same data as Fig. 5a plotted for constant weight loadings. These various figures of net production versus percent solids show the location and extent of the regions A, B, and C presented in Part 1 as a function of solids loading. It is obvious that the rheological transformation pattern described earlier does not hold true for slurry loadings corresponding to less than the void volume of the media, which is also a region of

Jan 1, 1983

By Frank E. Dalton, Forrest C. Neil

INTRODUCTION The Tunnel and Reservoir Plan (TARP) (Figure 1) was adopted in 1972 as the most cost-effective way to bring Chicago area waterways up to Federal and State water quality standards. TARP will significantly reduce pollution of these waterways and provide flood relief for Chicago and 53 adjacent suburban communities. These communities, covering an area of 971 sq km (375 sq miles), are at present served by combined sewers, which carry both raw sewage and stormwater. Because porous ground surfaces have been covered over in recent years by buildings, streets, and parking lots, stormwater runoff into sewers frequently exceeds the capacity of the sewers. When this happens, sewers back-up into hundreds of thousands of basements, and the overflows on the combined sewers discharge rainwater mixed with raw sewage directly into the area&apos;s waterways at 645 overflow points. The result is severe pollution of the waterways and flooding in 53 communities. During particularly heavy rains, overloaded rivers have to be relieved by opening the locks and allowing the polluted waterways to flow into Lake Michigan, the region&apos;s water source. Goals of TARP 1. PREVENT BACKFLOWS INTO LAKE MICHIGAN. 2. ELIMINATE WATERWAY POLLUTION CAUSED BY COMBINED SEWER OVERFLOWS. 3. PROVIDE AN OUTLET FOR FLOOD WATERS.

Jan 1, 1981

By Yutaka Mochida

OUTLINE Beginning in 1946, a careful geological survey was made of the Tsugaru Straits. In 1964, excavation of the exploratory tunnels were started to observe the characteristics of faults and rock formation directly, and to study construction methods of excavation and sealing water inflow. In March 1971, the investigation stages were over, and in April 1971, the construction project was authorized from the government. The geological features in the straits may be divided into three broad classes. One third consists of andesite on Honshu side. The other two thirds consists of tuff. The middle of the straits consists of tuff, so-called Kuromatsunai-layers. On Hokkaido side, it consists of tuff, called as Kunnui-layers. There are nine noteworthy faults on the route. Prior to the excavation of the main tunnel, the horizontal pilot tunnels and service tunnels are made. Exploratory borings are taken to confirm the geological conditions and the presence of gushing water. Groutings for sealing water inflow are carried out when necessary. In geologically bad conditioned sections such as disintegrated or fractured zones, special methods are applied. In geologically good zones, the tunnels are bored through using the same methods as for a mountain tunnel driving. The pilot tunnel being constructed at the sea bottom is under direct control of the Japan Railway Construction Public Corporation. The service tunnel and the main tunnel are being excavated by contractors.

Jan 1, 1981

By H. Dr. Boldt, J. Dr. Henneke

PREFACE In German coal mines the application of tunnel boring machines has become a very effective and economic technique for major development works. After initial trials around 1970 the breakthrough was reached by driving 13 km of road ways on Rheinland and Friedrich Heinrich collieries, using a DEMAG tunnel boring machine of 6 m diameter. INTRODUCTION The coal mines of Rheinland and Friedrich Heinrich are to be found in the West of the Ruhr Area, the largest coal mining area in the Federal Republic of Germany (Table 1). They form part of the Ruhrkohle company. Rheinland coal mines produces 41000 to 43000 t of run-of-mine coal every day, of which 20500 t are usable coal. Friedrich Heinrich has a daily production of 17000 t of run-of-mine coal, 9000 t of which are usable. The coal is worked at depths of 600 to 1100 m in seams 0.6 to 3.0 m thick. The method of mining is longwall, and the machines used are ploughs and shearer loaders. From 1973 to 1980 a programme was put into operation in these two mines to develop and open up the coal field on the 885 m level. A total tunnel length of 20 km was to be driven. After thorough investigations it was decided to employ a full-face tunnel boring machine for

Jan 1, 1981

By William J. Miles, Raymond E. Blair

The oil and gas drilling industry is the largest user of "functional" industrial minerals for well drilling and completion. (Functional industrial minerals can be defined as those used for performance characteristics rather than composition.) This industry&apos;s use of industrial minerals involves complex mining, processing, and distribution of products. The cost of these products at the well site reflects the complexity of distribution to typically remote locations and the cost of service. Table 1 illustrates the use of functional industrial minerals by the drilling industry. The total tonnage shown is almost 2 1/2 times larger than the 3.3 Mt (3.6 million st) of kaolin used by the paper industry for filling and coating, another major use for functional industrial minerals. Drilling fluids are an indispensible part of a drilling operation. These fluids perform several functions simultaneously. They cool and lubricate the drill bit, remove formation cuttings, increase the specific gravity of the fluid to counteract formation fluid pressures, provide a filter cake on the wall of the drill hole to prevent drilling fluid loss to the formation, protect the porosity of producing zones, and prevent reaction of the formation or formation fluids with the drilling mud. When porosity of a formation exceeds the ability of the drilling fluid to form a wall cake, it is referred to as lost circulation. Because these fluids are being constantly formulated for changing formation conditions, they require a skilled technician or drilling mud engineer on the site at all times. Drilling fluids are composed of oil or water as the liquid phase, and industrial mineral products and chemicals to control chemical and physical properties. The basic function of viscosity and suspension result from the use of gelling clays and chemical and mineral dispersants; specific gravity of the mud is adjusted with mineral weighting agents; filtration control is maintained by clays and various natural and synthetic polymers; platey minerals and scrap products are used for controlling lost circulation in porous or fractured zones; salts are added to the mud to inhibit shale and clay swelling; chemicals are added for pH adjustment, prevention of corrosion, and as scavengers for formation fluid components. Because of the clay component, drilling muds have rheological properties different from conventional fluids, behaving as Bingham plastic fluids as opposed to the Newtonian behavior of water and oil. Newtonian fluids will begin to flow with the application of any force, however small. Bingham plastic fluids require a finite force or shear stress (yield value) before flow begins. Thixotropy is another property of clay-based drilling fluids. At rest they form a gel structure that suspends the weighting agents and rock cuttings. These gels break down when a finite force is applied and circulation is restored. At the bit where shear rates are the greatest, the viscosity or resistance to flow decreases, so hydraulic pressures and pumping costs are minimized. A drilling rig provides a means of rotating a hollow pipe attached to a cutting bit. A mud pit or tank is used for mixing the drilling mud and its components. A centrifugal pump delivers this fluid to the drill ripe and down to the bit

Jan 10, 1983

By R. E. J. Putman

The past ten years have witnessed substantial development of electronic equipment for execution of process control functions. The methodology of giving instructions to the data-handling system and the organization of the system, both the equipment and instruction coding taken together, have developed simultaneously. Examples of the technology specific to the mineral processing industry can be cited. Approaches to system design developed for the Pinto Valley concentrator incorporating slave and master data processing have been described by Arney, and his associates (1974). Madge (1970) has described the hierarchical systems employed at the operations of Cominco Ltd. The Kennecott Garfield smelter is controlled by a system of microprocessors linked to a general purpose data processor (Marchant, et al., 1977). These systems provide innovative approaches to couple advancing technical capability in electronic data processing to the objectives of process management. The current state of the art described in this chapter is certain to require updating in the 1980&apos;s with the advances in technology anticipated.

Jan 1, 1979

By J. W. Danni

Today&apos;s mining industry faces many challenges. Perhaps none is more important than the challenge of improving our industry&apos;s public image. Opinion polls document public concern for a clean and safe environment. As part of that public, the mining industry must share that goal. The public is now the most powerful environmental group in society. And the public wants the environment to be protected. In May 1989, Edgar S. Woolard, chairman of DuPont, spoke to the American Chamber of Commerce. He said that industry&apos;s continued existence "requires that we excel in environmental performance and that we enjoy the non-objection - indeed even the support of the people and governments in the societies where we operate." In effect, Woolard called for "corporate environmentalism." He defined it as an "attitude and a performance commitment that places environmental stewardship fully in line with public desires and expectations." Environmentalism is no longer a fringe activity, but rather is now clearly in the mainstream. How can we meet public expectations and improve our image as an industry? One of the best ways is to plan, design and operate our mine facilities with environmental responsibility and social concern. The Mineral Hill Mine provides a good case study of a facility that has made this commitment. The project used an inter-disciplinary, multiagency task force, citizen advisory groups and engineering and design considerations. As a result, Mineral Hill achieved cost-effective permitting. At the same time, the operation demonstrated effective "corporate environmentalism."

Jan 1, 1992

By Giin-Fa Fuh, Sally A. Shoop

An instrumentation program was developed based on the results of an analytical study of the geomechanical effects of longer longwall face lengths. Boundary element simulations showed that longer face lengths can cause in- creased face convergence and an increase in the shear stresses in the immediate roof. Empirical design methods predict that longer faces will cause little effect on abutment stresses as long as the roof caving is well behaved. On this basis, a longwall face instrumentation program was designed with emphasis on the interaction between face support and ground response for optimizing face conditions. At a 600-foot (183 m) face, five midface shields and two headgate shields were monitored with vary- ing hydraulic pump pressure. The instrumentation included six convergence rods with linear potentiometers to measure canopy-to-toe convergence; fourteen pressure transducers to monitor leg pressures; and two portable data loggers. Similar instrumentation will be in- stalled on a 750-foot (229 m) face for comparison. The results from the 600-foot (183 m) face indicate that a ground reaction curve, as determined from the relationship between the sup- port set pressure and the roof convergence, can be used to optimize the support pressure to control convergence, the key element to ground stability in the face area.

Jan 1, 1986

By Kerry Burns

Contrary to active subsidence, which occurs concurrently with mining operations, or is completed within a few days following coal extraction, delayed subsidence may take many years to appear at the surface after coal mines are abandoned. There are two principal morphological types of delayed subsidence: troughs, which are shallow depressions, and sinks, which are steep-sided crown pits. Both types are damaging to surface structures, and a variety of methods have been introduced to deal with the problem, ranging from subsidence insurance to site restitution. In planning insurance or restitution measures, a predictive model is of value in estimating the magnitude of the problem and the size of long-term budgetary commitments. Only one model is known, which was developed for the Bureau of Mines by GAI Consultants of Monroeville (l,2,3). The GAI model is presented in qualitative terms. This report develops a formal basis for the model and tests a numerical implementation on one of the best-described study areas, Allleqheny County in Pennsylvania.

Jan 1, 1982

By Daryl R. Tweeton

The Bureau of Mines has developed PC-based tomographic computer programs for geophysical applications, and is making them available to potential users as part of a Bureau plan to facilitate the transfer of technology to industry. These programs were initially developed for predicting and monitoring the flow pattern of leach solution during in situ mining. Seismic crosshole tomography has located fractured zones of low seismic velocity and saturated zones of high seismic velocit above the natural water table. The Bureau has applied tomography also to assessing high-wall blast damage, and examining the integrity of mine-related geological structures. The tomographic programs include the straight ray pro ram BOMTOM (Bureau of Mines Tomography? and the program BOMCRATR (Bureau of Mines Curved Ray Tomographic Reconstruction) that can be run with either curved or straight rays. Both programs provide optional mathematical constraints to help counteract the nonuniqueness of reconstructions that occurs with crosshole data. They are available from the Bureau free of charge. With typical data sets, they can be run on a 386 microcomputer with 640 Kb RAM. BOMTOM was described in the Bureau Report of Investigations 9159, so this report emphasizes BOMCRATR. Curved and straight ray reconstructions using seismic field data collected while simulating injection of leach solution were compared. The curved and straight ray tomograms were quite similar even with velocity variations of more than 50 percent.

Jan 1, 1992

By Agne Rustan

Most of the mines in Sweden are metal ore mines in hard rock and none of these mines are classed gassy because there is no methane emission. The risk of methane explosions in Swedish mines is therefore very small. Since the 1960?s, in Swedish mines, there has been a change from electric and pneumatic loaders and transport machines to diesel. Today in almost all Swedish underground mines diesels are used. One of the most common complaint from the underground mine- workers is the exhaust gases from the diesel-vehicles. This is a strong motive for attempts to assure a more comfortable environment. Another motive for a better efficiency of ventilation under ground is the increasing cost of energy for fans and for heating the air during winter. For the largest mine in Sweden, the Kiirunavaara Mine, 36% of the energy for ventilation is used for preheating the air during the seven months when the temperature is below zero. The air quantities used for ventilation are large. In table 1 a comparison of the ratio between yearly produced ore and waste rock and installed fresh &apos;air capacity is shown. [ ]

Jan 1, 1980