Search Documents

By Rick Bearce, Minsu Cha, Mike Mooney, Yuanli Wu, Lisa Mori

"Proper soil conditioning is critical for effective earth pressure balance (EPB) TBM tunneling. Chamber pressures can reach 3-5 bar yet the vast majority of testing is performed under atmospheric conditions. This paper illustrates how pressure influences foam stability and conditioned soil behavior, and how atmospheric test results must be viewed in the context of expected chamber pressures. Torsional shear strength, compressibility and abrasivity of foam conditioned sand were found to be ideal when the void ratio was above the ASTM-determined maximum void ratio, achieved by sufficiently expanding the soil grain structure with foam, herein when the foam injection ratio at pressure exceeded 45%. Otherwise, the engineering properties of foam conditioned sand were not ideal, i.e., appreciable torque and abrasivity, low compressibility. INTRODUCTION Proper soil conditioning is critical for effective earth pressure balance (EPB) TBM tunneling. The formation soil at the cutterhead must be transformed into a highly compressible, low shear strength and low permeability medium within the excavation chamber to allow effective EPB performance. This behavior must be maintained for a certain residency time while the soil is in the chamber and screw conveyor. The vast majority of published studies on conditioned soil behavior have been performed under atmospheric conditions (Quebaud et al., 1998; Bezuijen et al., 1999; Psomas and Houlsby, 2002; Vinai et al. 2008; Thewes et al., 2012; Peila, 2014); however, the desired soil behavior must occur under chamber pressures that can reach 5-7 bar. The influence of pressure on conditioned soil is significant and is dramatically different than behavior under atmospheric pressure (Williamson et al., 1999; Mori et al., 2015). This paper illustrates how pressure influences conditioned soil behavior and how atmospheric test results must be viewed in the context of expected chamber pressures. The influence of pressure on foam bubble size (including with time) is shown through digital image analysis. The influence of pressure on foam half-life is also investigated. The compressibility, shear strength, and abrasivity of conditioned soil under pressure is presented and explained in terms of density, soil and air compressibility and porosity."

Jan 1, 2016

By D. A. Bird

Water chemistry data were used to identify the sources of ground-water and surface-water inflow to the IOZ block cave mine. Water samples were collected to obtain vertical and lateral hydrochemical profiles within different levels of the underground workings. Water chemistry data were evaluated in conjunction with geologic and structural information to define controls on locations of ground-water inflows, and to select targets for drilling and interception of water. Drilling has intercepted water-producing zones that were previously unidentified through mapping and drilling. The program has resulted in a reduction in water inflows to the block cave area.

Jan 1, 1998

By P. L. Sibrell

Previous research by the U.S. Bureau of Mines showed that autoclave cyanide leaching of used automobile exhaust catalysts for recovery of platinum group metals (PGM) was technically feasible. This work involves a more detailed investigation of the chemistry of the dissolution of PGM in cyanide solutions. The PGM species in solution identified by ultraviolet spectroscopy. Pt and Pd cyanide complexes were square were The planar in geometry, while the Rh complex was octahedral. The rate of dissolution of the PGM was also investigated using a rotating disk technique. Dissolution rates increased in the order of Rh, pt, and Pd, respectively.

Jan 1, 1994

By Jun Ho Lee, Dae Young Kim, Ebrahim Farrokh, Ki Chang Hyun

"The Jinhae Geoje gas pipeline tunnel project is the largest (7.8 km) and the deepest (90 m) subsea tunnel in South Korea. This tunnel will house a pipeline to carry natural gas from the mainland to Geoje Island southeast of the country to alleviate the increased demands for natural gas, especially in the winter season. Tunneling is currently underway using two slurry shield TBMs of 3.5 m diameter. This paper describes the major design elements of the tunneling machines and their performance evaluation. For this purpose, a thorough analysis of geotechnical information was performed to evaluate the tunnel elevation to reduce the risk of tunneling under high water pressure in unstable and permeable rock mass under 9 bar water pressure. TBM specification and TBM performance were also analyzed using different methods, including well-known models as well as a rotary cutting machine test developed in house in Hyundai Engineering and Construction Company. INTRODUCTION High demand for natural gas, especially in winter season was the primary driving factor for the design of the Jinhae Geoje gas pipeline project. This project is located southeast of South Korea between Jinhae district and Geoje Island and runs for over 50 km length. The mid part of this project includes a 3.5 m diameter subsea tunnel consisting of two sections of Geoje to Jiri Island (4.3 km) and Jinhae to Jiri Island (3.5 km). Figure 1 shows the tunnel project location and its layout. Figure 2 shows the geological profile along the tunnel. As can be seen, the tunnel passes mainly through three rock types: granite, tuff breccia, and andesite tuff. This tunnel was planned to be constructed by two face pressurized shielded TBMs and to be lined with a segmental lining of 2.8 m internal diameter. The major challenge for this tunnel is its maximum expected water pressure at the tunnel invert (8.83 bar). At such a high water pressure, the TBMs required special design to ensure they can handle unexpected water pressure and to ensure the risks for the TBM maintenance intervention are minimal. In this regard, a thorough analysis was conducted on the TBM design parameters and geotechnical information to define required TBMs’ design parameters and to identify the safest tunnel elevation. This paper provides a brief overview of the project geotechnical information, TBM selection and its design specification, tunnel elevation selection, and TBM penetration rate evaluation. In this regard, a rotary cutting machine testing equipment was used to perform trial tests on a similar rock type encountered along the tunnel for performance evaluation and optimization."

Jan 1, 2016

By William G. Freeman

As with most industrial minerals, barite is freight sensitive. This paper is given so that others might gain from the experience of barite companies in reducing their transportation costs. Some of the approaches used were unusual and others standard, but by perseverance considerable savings were realized.

Jan 1, 1973

By Wei Li

Carbothermic reduction kinetics of ilmenite concentrates catalyzed by sodium chloride and the microwaveabsorbing characteristics of the resulting reductive products were investigated; the reduction degree of the reaction was deduced to be . Results show that the activation energy is 112.03 kJ/ mol when NaCl is used as catalyst, lowering to 23.11 kJ/mol for the final stage activation energy using sodium silicate as a catalyst. There is a sharp change in the reduction rate constant at temperature ranges of 1,223 K - 1,273 K and 1,373 K - 1,423 K. Microwave-absorbing characteristics of reductive products were measured by the method of microwave cavity perturbation. It was found that microwave-absorbing characteristics of reductive products obtained at temperatures of 850° C, 1,100° C and 1,150° C show sharp changes. Through X-ray diffraction (XRD) characterization, it was found that the formation of Fe occurs at a temperature of 900° C during the reduction process of ilmenite concentrate. The decrease of FeTiO3 content results in the decrease of microwave-absorbing characteristics, while the increase of Fe content gives rise to the increase of microwaveabsorbing characteristics. The decreasing trend is larger than the increasing trend, which is the main reason for the sharp changes in the microwave-absorbing characteristics of reductive products at the temperature range of 850° C to 900° C. When the decreasing trend is smaller than the increasing trend, it becomes the main reason for the sharp changes in microwave-absorbing characteristics of reductive products at the temperature range of 1,100° C to 1,150° C. Kinetics results show that sodium chloride can catalyze the carbothermic reduction of ilmenite, and microwave-absorbing characteristic investigations indicate that microwave heating can be used in the carbothermic reduction of ilmenite.

By James L. Coburn

Leaching is defined as a form of extraction in which a valuable constituent is removed from a solid body by mass transfer to a solution which, for the purpose of this discussion, is considered to be an aqueous medium. Historically, leaching has been applied to the recovery and purification of many elements. This paper, however, is directed toward the recovery of copper, uranium, vanadium, and precious metals included in the following systems: 1. The leaching of copper minerals, sulfides and oxides, by acid or by ammoniacal leach solutions with or without an oxidant. 2. The leaching of gold and silver, either native metals or as minerals by an oxygen-containing alkaline cyanide solution. 3. The solubilization of certain uranium and vanadium minerals by oxygen or oxidant-bearing lixiviants. Many other systems of this general type exist, but from a production standpoint, these three systems account for most of the major values recovered by leaching.

Jan 1, 1975

By K. Y. Haramy

A scale-invariant theory of the strength and deformability of rock masses in static equilibrium and at incipient failure is proposed. The theory provides a rationale for designing structures in rock. This paper presents results of experiments conducted by the U.S. Bureau of Mines and theoretical methods to determine and interpret in situ strength of rock masses using the borehole shear tester.

Jan 1, 1995

"A cationic surfactant, tetradecyl tributyl phosphonium chloride (TTPC), was first used as a collector. Flotation characteristics of muscovite using TTPC have been investigated through flotation tests. And dodecyl trimethyl ammonium chloride (DTAC) was tested for comparison. Their adsorption mechanisms on muscovite surface were clarified using zeta potential measurement, DFT calculation and molecular dynamics (MD). The flotation results indicate that the recovery of muscovite decreases when the pH increases in the presence of surfactants. When a maximum of recovery was reached, the dosage of TTPC was 2×10-5mol/L which was half of that of DTAC. Zeta potential measurements confirm that the TTPC displays a stronger collecting power than DTAC and is a superior collector for the muscovite flotation. DFT calculation and MD simulations show that TTPC interacts with the muscovite mainly through electrostatic attraction and hydrogen-bonding. The conclusions drawn from purely theoretical computations matched remarkably well with the experimental results. Keywords: Quaternary phosphonium salts; Flotation collectors; Flotation INTRODUCTION Muscovite mica is widespread in igneous, sedimentary and metamorphic rocks. It has the general composition KAl2(AlSi3O10)(OH)2. Muscovite mica exhibits perfect cleavage along the (001) plane, which exposes interlayer potassium ions[1-3]. In aqueous suspensions, the potassium ions readily enter into solution, leading to the development of a net negative charge on the (001) plane[4-6]. The surface of the muscovite mica is negatively charged at all pH > 1[7]. Due to the negative charge surface over the whole pH range of 2–12, the muscovite mica would not be expected to respond to anionic collectors in the absence of an activator. Conversely, the mineral is readily recovered using cationic collectors. However, until now, various amines and their derivatives (with N atoms as the center) are still the only available cationic collectors which still had their shortcomings such as weak selectivity, low flotation speed. Since few types of cationic collectors could be used, in some sense, the limitations of collectors are increasing significantly and the cationic flotation is facing more and more challenges. Quaternary phosphonium salts, as novel cationic surfactants, are widely used in antimicrobial, catalysis and surface modification field due to their biological activities, hydrogen bonding capability, stability and superior group electrical property[8-10]. There are a number of processes where quaternary phosphonium salt surfactants have shown better properties than quaternary ammonium salts and amines. Although the adsorption of quaternary phosphonium salt surfactants at the bacterium–liquid interface has been studied thoroughly, the case of adsorption in mineral surface has not been investigated thus far."

Jan 1, 2016

By J. H. Kempton

The scrutiny given to model predictions of pit-lake water quality has focused attention on the uncertainty associated with long-term predictions. Although comparison of probabilistic predictive modeling of water quality in existing pit lakes indicates that short-term predictions can bracket most parameters, uncertainties in wall-rock reactions and the stability of groundwater composition and climate remain unquantified. This overview of the uncertainties associated with longer-term predictions is presented as support for those considering policy decisions that must be made in the absence of reliable estimates of future conditions.

Jan 1, 1998

By K. E. Doud

An unusually pure grade of rutile and several grades of aplite rock are produced in a unique mining and mineral dressing operation in Hanover County, Virginia. The ore body is an aplite rock of gnessic structure, having a sari ace exposure extending over several hundred acres, heavily leathered and containing rutile, ilmenite, and other titanium and iron minerals. The physical nature and mineral composition of the ore body has permitted the use of a relatively economical and unusual processing circuit. The flowsheet was designed to take full advantage of the remarkable liberation of the minerals at relatively coarse rinds. It permits flexibility in changing the product mix, and maintains high levels of purity in both rutile and aplite rack. The mineral processing is discussed in some detail below.

Jan 1, 1962

By Z. Yu

The effect of particle size on coal dewatering has been well recognized However, there are no systematic studies on ultrafine coal dewatering. The results discussed last year revealed the effect of flocculant type and coal wettability on the filtration of ultrafine coal In this paper, the differences in dewatering between -25 µ m ultrafine and -500 µ m fine coal with addition of flocculants, surfactants and oil-emulsions in vacuum filtration are further investigated Significant differences were observed in the reduction of the cake moisture. The utilized emulsions were found to be very powerful and promising filtration aids for both ultrafine and fine fractions of hydrophobic and hydrophilic coal

Jan 1, 1995

By Michael J. Friedel

The scale-dependent hydraulic properties in a fractured porphyry copper oxide deposit are investigated for relevance to in situ leach mine (ISLM) design. In most well field designs, mine operators assume that hydraulic properties represent a continuous spatial function, or continuum. The problem, however, is that the representative elemental volume, the volume over which hydraulic properties are described as a continuum, is a domain (if it exists) that occurs between end members representing varying degrees of heterogeneity. At the Cyprus Cas a Grande mine, transmissivity fluctuations are spatially correlated suggesting that at the scale of ISLM, the hydraulic process is heterogeneous and a typical continuum representation is inappropriate for design. Alternatively, a conditional stochastic approach using the simulated annealing (SA) technique is deemed useful for the imaging of heterogeneous hydraulic properties. Specifically, SA preserves transmissivity extremes and spatial complexity, both necessary for accurate conditioning of a flow simulator. Also, the stochastic continuum approach provides an avenue whereby uncertainty (or risk) may be addressed. Currently, the SA weaknesses are that it is computationally time consuming, and uncertainty may increase when simulating under conditions of statistical isotropy. Recognizing that ISLM exerts a dynamic influence on hydraulic properties with time, the mine design should be reevaluated at intervals throughout the evolution of the leaching process.

Jan 1, 1993

By A. C. Lyons

Foreword Sir William Halcrow and Partners are responsible for the design of the Ahmed Hamdi Tunnel as Sub-contractor to the Contractor, Osmac, a joint venture formed by the Arab Contractors, Osman Ahmed Osman and Company of Cairo, and Tarmac International of London. Throughout the paper the term "Client" refers to the Employer, the Ministry of Housing and Reconstruction, which latterly became the Ministry of Development and New Communities of the Arab Republic of Egypt. At the time of writing of this paper only a few hundred metres of the tunnel have been driven, but the design is substantially complete. Introduction The Ahmed Hamdi Tunnel, which is at present under construction, will be a two-lane tunnel crossing beneath the Suez Canal approximately 15 km north of the town of Suez at El Shallufa. It will become the first permanent connection across the Canal since 1967 and is visualised by the Egyptian Government as an early step in the development of the Sinai Desert along the eastern bank. The tunnel will carry pipelines for treated water and electric power cables to assist in this development. The tunnel, which will be 1640 m in length, is being driven through hard clay and mudstone using a tunnel shield fitted with hydraulic excavators. The primary lining is being constructed with precast, bolted reinforced concrete segments with an internal diameter of 10.4 m. The road deck structure and the walls of the air supply ducts beneath it are formed with precast, reinforced concrete units erected immediately behind the shield.

Jan 1, 1979

By T. N. Moore, E. M. De Souza

Because jackleg rock drills are a potential source of hand vibration exposure, they can effectively produce Hand Arm Vibration (HAV) Syndrome in their operators. This will affect operator efficiency and mine productivity. As a result, a significant amount of work has focused on redesigning rock drill handles using new materials to minimize hand-transmitted vibration. In previous work developed by the authors (1991), a detailed study was undertaken to determine the effectiveness of using elastomer covered handles in place of the standard steel design. The results indicated that, for an elastomer-based handle design, the overall acceleration level experienced by the hand can be reduced by as much as a factor of three, relative to the steel handle. It was also shown that this reduction takes place predominantly in the frequency range above 500 Hz. This paper presents an investigation of the long-term effectiveness of an elastomer-cushioned handle under different conditions underground. In this study, sponsored by the Mining Industry Research Organization of Canada (MIROC), a number of cushioned handles were quantitatively and qualitatively tested in five operating mines. The vibration testing program has indicated that the cushioned handle can reduce overall vibration levels by as much as a factor of three. The qualitative assessment program of the cushioned handles by the drill operators has indicated some degree of preference for the cushioned handles over the steel handles, if certain design modifications are performed. This research program indicated that cushioned handles have the potential to become the dominant method with regard to vibration reduction and operator performance.

Jan 1, 1994

By A. M. Raichur

The selective adhesion of hydrophobic Mycobacterium phlei to coal particles is responsible for flocculation of fine coal from associated ash forming minerals. The driving force for the differential adhesion is the hydrophobic interactions between the fatty acid surface of the organism and hydrophobic nature of coal. The effect of Mycobacterium phlei on surface hydrophobicity, surface charge and mechanism of adhesion on coal and associated minerals are controlled by several factors including hydrophobicity and surface and solution chemistry of the system. Adhesion measurements indicate that maximum adhesion occurs below the isoelectric point (IEP) of the coal particles. While massive adhesion of Mycobacterium phlei is observed on coal, however, negligible amount of Mycobacterium phlei attaches to mineral pyrite and quartz.

Jan 1, 1995

By Henry N. McCarl

[ ]

Jan 1, 1966

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner's cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutter head, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head's effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner improved air quality at both locations to varying degrees in some cases and not in others when compared to a continuous miner with a standard spray system.

Jan 1, 2010

By M. J. Carlson

With the goal of improving the strength characteristics of pneumatically emplaced material used for localized subsidence control, the binding additives: fly ash, bentonite, and Portland Cement, were examined for their effect on the support capabilities of coal refuse. It was found that, within certain concentration ranges, all three of them offered some increase in the ultimate strength of the backfilling mixture; however, Portland Cement gave the greatest percentage increases. Selection of the appropriate backfilling mixture will allow for the most economical and efficient subsidence control when pneumatic stowing is employed.

Jan 1, 1987

By John W. Antalovich

Normally I would like to begin a talk on photogrammetry by defining the word. However modern technology has changed the science so radically that it bears little resemblance to its original definition. Photogrammetry as defined is a science of taking accurate measurements from photography. Today's photogrammetrist, in addition to working with photography, finds himself working with magnetometers, infrared scanners, radiometers, holo¬graphy, lasers, side-looking radar, digital interfaces, computers and countless other modern space age concepts. The modern photogrammetrist is a pilot, photographer, lab technician, mathematician, geologist, programmer, engineer, physicist, and cartographer. His modern instrumentation and many spheres of activity all have a role in the environmental sciences. For example, the magne¬tometer which measures the earth's magnetic fields is used to locate the earth's ore deposits. The infrared scanner captures the heat emitted from the earth to detect ground waters and thermal pollutions. To elaborate on each of his many endeavors would take volumes rather than this short paper. I have elected therefore to discuss what I feel is his most important role in the environmental sciences - that of cartographer.

Jan 1, 1970