Search Documents

By A. C. du Preez

The separation of nickel and cobalt from calcium, magnesium and manganese by solvent extraction using synergistic mixtures of carboxylic acids was studied. Addition of certain viable synergists to commercially available tertiary branched carboxylic acids, such as Versatic 10 (Shell) or Neodecanoic acid (Exxon), produced large synergistic shifts (?pH50) in the pH50values for nickel, and small antagonistic shifts (negative ?pH50values) in the extraction of calcium. Under the initial test conditions used (0.50 M each of Neodecanoic acid and the Mintek synergist, in xylene) a large separation (pH50Ca? pH50Ni= 3.09 pH units) between nickel and calcium in their extraction from 1.00 M sodium nitrate solutions was obtained, compared with only 1.11 pH units in the absence of the synergist. The selectivity series for the extraction of divalent base metals from 0.333 M sodium sulphate solutions by 0.50 M Neodecanoic acid and 0.25 M of the Mintek synergist in C12-C13aliphatic diluent was found to lie in the order (with pH50values in parentheses): Cu(3.42) > Ni (5.08) > Zn (5.58) > Co (5.73) > Mn (6.62) > Ca (7.48) >Mg (8.25). In batch counter current experiments, a simulated leach liquor containing (in gL-1): Ni 5, Mg 5, Mn 2, Co 0.5, Ca 0.5, Cu 0.1and Zn 0.1 was contacted with the mixed extractant in three stages at unit phase ratio and an equilibrium pH of 5.9. The recovery of nickel was 99.9 per cent and that of cobalt was 84.7 per cent, whilst the co-extractions of manganese, calcium and magnesium were 2.7,1.5 and 0.04 per cent, respectively. The recovery of cobalt can be enhanced by employing a slightly higher pH, although this will also increase the extraction of manganese, calcium and magnesium somewhat. Nearly quantitative stripping (99 per cent) of nickel from the loaded organic phase was achieved in a single contact at an organic-to-aqueous phase ratio of 4 using a simulated spent electrolyte containing 39 gL-1sulphuric acid and 33 gL-1nickel,thereby producing an ?advance electrolyte? containing 57 gL-1nickelat pH 3.5. Loading of acid into the organic phase was very slight, amounting to only 0.002 M H+in contact with the above-mentioned spent electrolyte. Keywords: solvent extraction; synergism; nickel; calcium; carboxylic acids.

Jan 1, 2004

By John V. Simmons, Peter J. Simpson

Excavated slopes in open pit coal mines are designed to be as steep as possible consistent with stability and safety requirements. Slope failures occur for many reasons, including oversteepening. This paper is concerned with slope design and excavation experience in the Bowen Basin coalfields of central Queensland (Figure 1), [ ]

Jan 1, 2006

By J. R. Menasce

Mechanization in low-stope panels situated in hard rock infers roof support by tensile bolting to allow free passage of trackless mining equipment in the production areas. This is in sharp contrast to conventional mining, where compressive roof supports?such as timber and grout packs?have traditionally been used, up to 1.5 metres from the production face. Bolting is a hazardous operation because material is dislodged from the roof during the drilling activity. Even with temporary roof support installed, small pieces of rock are dislodged by the percussive action of the drifter. Operations with the man situated directly under the drill, during the drilling activity, are hazardous. The only way to remove the hazard is to move the man away from the machine for as much as possible throughout the complete cycle Costs associated with safety cannot be quantified, but need to form part of the decision-making process. Machine selections based on purchase and running costs alone do not justify the investment cost of mechanized bolters. The equipment selection process needs to take into account the total cost of mining as well as the human safety impact and loss of production costs from having to re-bolt roofs in a production panel to prevent falls of ground. Labour costs in mechanized low-stope bolting are between one-quarter and half the labour costs of non-mechanized bolting. This paper reviews the mechanized bolting option versus handheld bolting from a mining process and cost perspective in a hard rock, low-stope room-and-pillar mining operation in the platinum and chrome industries.

Jan 1, 2006

By D. Chetty

Process mineralogy forms an integral part of geometallurgy, with ore body characterisation being but one piece of the puzzle in optimising value derived from ore. This value is not only financial, but importantly speaks to sustainability from environmental and social standpoints. The reactive approach of traditional process mineralogy is increasingly being replaced by predictive methods in the geometallurgical sphere, for which mineralogical information must be timeously acquired on judiciously selected sample sets to understand ore variability and its impact on orebody processing. Such processes are not only metallurgical, but must incorporate mining and waste management protocols. Dwindling resources like water and energy also demand innovative approaches for lowering consumption and/or promoting recycling along the value chain. Addressing such challenges relies on appropriate characterisation of ore behaviour under different process regimes. Coupled with this, emerging characterisation tools are increasingly applied to understand the mineralogy of unconventionallypresented and difficult-to-process ores to meet societal and technology demands. Such tools are often accompanied by the generation of large, computationally intensive datasets, for which data management and storage are key requirements, particularly when deciphering temporal trends in ore and process variability. This paper will elaborate on these themes with examples that highlight the importance of process mineralogy throughout the minerals value chain. Keywords: Process mineralogy, ore characterisation, geometallurgy

Jan 1, 2020

By P. Rice, A. Photolo, A. C. Barnard

Introduction -Sampling Tool Project (STP) -History -Results to date -Costs -Questions

Jan 1, 2005

Application of Gy?s formula is appropriate for calculation of the Fundamental Error (FE) prior to samples being collected at any stage of the minerals process, provided that sampling parameters K and a (alpha) have been determined by calibration of the ores. Two types of calibration procedure are well established in the industry, the Hetrogeneity test and the 32-piece sampling tree experiment. The sampling tree experiment uses the variance and average grade of metal analyses from four series of samples at different nominal fragment size, as the basic input data. Pierre Gy suggested the cube as an appropriate exponent of the nominal fragment size for use in his equation. More recent work suggests that this exponent is variable and characteristic of specific ores and therefore requires calibration. The method described here explains the experimental procedure of the calibration. It is then possible to calculate a sampling nomogram using the sampling parameters K and a. This allows the sampler to determine a suitable protocol for the sampling event that will ensure that the FE does not exceed a predetermined precision at any point in the sampling procedure.

Jan 1, 2007

Milling circuits are known to be difficult to control. In order to address these difficulties, it was decided to develop and test a model predictive controller (MPC) for a milling circuit. A milling simulator was written using Microsoft Visual C++ and used to design and test the MPC controller. Due to the large number of tuning parameters in a controller of this type, an optimizing algorithm was written that automatically tunes the controller. Good, robust control was obtained when the controller was tuned using this algorithm. Control was further improved by combining feedback and feed forward control and by using quadratic programming in the MPC algorithm. The movement of the manipulated variables was reduced by using a novel technique that allows the controlled variable to vary within a specified region around the set point. An optimiser controller was also successfully implemented to control the circuit at its maximum throughput.

Jan 1, 2000

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The stability of a ferrosilicon dense medium suspension is one of the most important parameters to keep under control since it determines the density gradient of the medium in the separation zone and thus directly influences separation sharpness. The stability of ferrosilicon suspensions were characterized using settling tests employing a differential pressure method. Particles smaller than 45 µm and especially the ore fines played an important role in the settling behaviour of the solids. High medium stability is favoured by ore fines, fine medium particles, and high medium densities. Keywords: dense media, ferrosilicon, dense medium stability, ore fines

Jan 1, 2002

By R. T. Jones

The 20 Mt reverberatory furnace slag dump at Nkana in Zambia contains a substantial quantity of cobalt. A 40 MW DC arc furnace has been built at Chambishi for the purpose of recovering cobalt from the slag. The technology was jointly developed by Mintek and Anglovaal Mining Ltd (Avmin), and the furnace was designed by Bateman Titaco. Testwork at the 150?250 kW scale was conducted at AVRL, and larger scale piloting was conducted at Mintek (in partnership with Avmin) in a 3 MW DC arc furnace. Approximately 840 tons of Nkana dump slag (ranging from 0.66% Co) was processed at power levels around 1-2 MW. Good overall cobalt extraction was achieved, and approximately 100 tons of cobalt-bearing alloy was produced (containing 5 to 14% Co). This testwork demonstrated that the Nkana dump slag could be processed in a DC arc furnace of suitable design, to produce a cobalt-bearing alloy suitable for further hydrometallurgical processing. Bateman Titaco were contracted to design and build the furnace, and the design team contained representatives from Avmin and Mintek. The project was conceived as a fast-track exercise, and many activities had to be run in parallel. Notable features of the furnace include an ABB power supply, a Concast conductive hearth, the refractory design, and copper cooling in the sidewalls. Power to the furnace was switched on during January 2001.

Jan 1, 2002

A South African gold mining rock-related fatal accident database has been analysed in order to determine rock-related fatality trends in the gold mining industry over the period 1990 to 1998. This analysis was extended further to include some of the individual reefs mined and focused particularly on the Carbon Leader Reef, the Ventersdorp Contact Reef, the Vaal Reef and the Basal Reef. Rock-related accident locations are also presented. A stope rock-related risk is proposed, where the fatality rate in terms of rock-related fatalities per million square metres mined for the gold mining industry as a whole is compared to individual reefs, allowing a stope rock-related risk to be attributed to the individual reef. This comparison is extended further by removing the contribution by the reef being evaluated from the industry data, thereby allowing this reef to be directly compared to the rest of the industry with respect to a stope rock-related risk.

Jan 1, 2001

The use of a time series variogram as an aid in controlling the quality of a product was pioneered by Pierre M. Gy and is described. The ability to analyse and interpret covariance relationships time series data is possible using the variogram. The concept of stream heterogeneity allows sources of variability in process streams to be identified and isolated. Principally this is distributional heterogeneity that is due to a short range effect of segregation in the process stream related to size or composition distribution of the material on a local scale and due to a long-range change in the size and grade of the material stream. The variogram is simply a tool for representing these sources of variability in a way that is explicit, allowing identification of the source and providing important insights to temporal continuity between samples. This paper describes the chronologically related large-scale variability in an iron ore process stream (%Fe), and illustrates the control and mitigation of variability at various stages within the process using a variogram. Three main sources of variability are identified including the random variability V[0], the process variability V[1], and the variability due to cyclical phenomena V[cyclic], arising from human routine or mechanical defects. These sources of variability can be represented on the control chart that provides the plant superintendent with insights as to the sampling capability of the systems in place. Maintaining levels of variability within customer specification limits requires that production systems be controlled without overcorrecting for the trends in changing quality. This can be done only by representing the limits of control relative to the limits of specification on a control chart. Where the specification limits encroach on the control limits, one or the other, or both, may need to be changed; specification limits that constrain the control limits lead to reactive decision making that is expensive and stressful for plant operators.

Jan 1, 2008

By L. Forsbacka, M. Nakamoto, L. Holappa

Viscosity of the slag is one of the central parameters when producing FeCr in submerged arc furnaces. It contributes to smelting behaviour and reduction kinetics of chromite ore as well as to the Cr recovery by influencing the separation of dispersed metal droplets from the slag. A typical FeCr process slag contains 5-10pct chromium oxides, CrO and CrO1.5. The neural network computation was applied to the evaluation of viscosity for slags containing chromium oxides, and the prediction of viscosity in FeCr process slag was conducted. The main results in this estimation were that the chromium oxides in FeCr process slag lower its viscosity, and that the effect of CrO on the viscosity decrease is greater than that of CrO1.5.

Jan 1, 2007

By R. M. Goktan

Point-attack picks are one of the most widely used tools for the mechanical excavation of rock and coal. In the literature, some practical formulas have been developed to estimate their performances under varying cutting conditions such as the pick geometry, cutting depth and cutting geometry. In this study, it is shown that Evans?s theoretical model, the most cited in the literature, has serious limitations concerning the changes in the cutting geometry. Analysis of the two independent full-scale linear rock cutting experimental data reveals that both his theory and its recent modification can not fully explain the mechanism of rock breakage under asymmetrical attack. The cutting force predictions made by employing such models are shown to be too significantly weak to be of any service in practice. In this study, a semi-empirical approach was followed by means of which cutting forces under varying cutting geometries could be made. By analysing the full-scale rock cutting test data, prediction equations of the peak cutting force and mean cutting force have been developed. Comparisons of laboratory determined and predicted force values indicate that the suggested prediction equations are applicable to quite different rock materialsm which have uniaxial compressive strength in the range of about 30?170MPa, and valid for different cutting geometries. It is also shown by regression analysis that the established prediction equations are statistically significant.

Jan 1, 2005

By A. Z. Toper

This is a sampling of the papers presented at the conference, the proceedings can be bought from the SAIMM An extensive research programme to address the issue of rockburst control has been undertaken over a number of years. This paper discusses the development of preconditioning techniques to control face bursts, for safer mining in seismically hazardous areas. Preconditioning involves regularly setting off carefully tailored blasts in the fractured rock immediately ahead of a mining face, so as to encourage slip on pre-existing fractures, in order not to allow the accumulation of high strain energy density in the rock mass. Two different preconditioning techniques have been developed, namely face-perpendicular preconditioning and face-parallel preconditioning. Both have prevented face bursting in areas to which they have been applied, even though several large seismic events have occurred close to the faces in some areas. In addition, minimal overall damage was observed in the preconditioned panels following these events, compared to similarly exposed unpreconditioned panels. Preconditioning has also provided some protection to the face area from distant events, through the capacity of the preconditioned ground to absorb energy. An improvement in hangingwall stability and productivity has also been noted in preconditioned areas. In order to determine the optimum blast parameters for achieving the most effective preconditioning, an extensive optimization study was carried out for the face-perpendicular preconditioning technique. While optimum values for parameters such as hole length, diameter and spacing were determined, it was ultimately concluded that the differences in results obtained by varying the preconditioning parameters were less significant than the clear positive differences observed when comparing preconditioned areas with non-preconditioned areas.

Jan 1, 2000

By H. Ogasawara

To study the preparation process of an earthquake, we should get closer to the hypocentre. In co-operation with ISS International, we had an experimental field (~200 m x~200 m) without dykes and faults in a South African deep gold mine. We have monitored more than 20,000 seismic events (M<2) with borehole tri-axial accelerometers. We used a data acquisition system with 15 kHz sampling and 120-dB dynamic range. In a remnant area at a distance of 100?200 m, an earthquake sequence associated with an M~2 event occurred. Significant changes in seismic parameters such as stress drop, b-value, energy index were observed associated with the sequence. We installed Ishii?s borehole strain meters and could monitor as large a strain change as 10-4associated with mining. However, sampling was only 4 times per hour and 12 bit A/D. A distance from the M2 sequence was ~100 m, being not close enough. Therefore, we found another field with several crosscut tunnels excavated across a fault where an M=2-3 event is expected. We installed the strain meter within several metres of the fault to monitor both shear and normal strains on the fault. The strains are continuously digitized with a 24-bit 25-Hz A/D conversion. The Earth Tide (10-8)is clearly detected. Seismicity induced by longwall mining can be compared to earthquake swarm induced by fluid intrusion to vertical dykes. We also found a decrease in energy index in the source area of M>5events a few days before the major events. Keywords: seismic monitoring, strain monitoring, seismic parameters, preparation process of an earthquake, South African gold mine.

Jan 1, 2002

"For effective steel refining in the ladle (secondary steelmaking) the amount of steelmaking slag that is transferred from primary steelmaking must be limited, because the steelmaking slag contains iron oxide, manganese oxide, and phosphorus oxide. Adverse effects of slag carry-over include increased consumption of deoxidizers, phosphorus pick-up by the steel, and increased ladle refractory wear. Infrared imaging at longer wavelengths is an effective non-contact method to detect slag in the tapping stream. Various devices are used to shut off the tapping stream rapidly. These include slag darts, pneumatic slag stoppers, and slide gates for steelmaking converters, and eccentric bottom tapping for electric arc furnaces. IntroductionOxygen converters and electric arc furnaces are used for primary steelmaking. For both process types, the product (liquid crude steel) has a similar composition: largely liquid iron, with around 800–1000 parts per million (ppm, by mass) dissolved oxygen and low but significant concentrations of carbon, nitrogen, and phosphorus. The steel is tapped into a ladle, which serves as the refining vessel to adjust the final steel composition and temperature before casting.Some steelmaking slag is inevitably tapped with the liquid steel. The mass of steelmaking slag tapped with the steel is termed ‘slag carry-over’. Controlling and limiting slag carry-over from steelmaking is a primary requirement for clean steel production (Fandrich, Lüngen, and Wuppermann, 2008). Steel cleanliness refers to limiting the concentrations of dissolved impurities (such as nitrogen, oxygen, phosphorus, and sulphur) and of nonmetallic inclusions (oxides, sulphides, and nitrides) in liquid steel and in the final solid steel product. Of these, the strongest effect of slag carry-over is on the content of dissolved phosphorus in the liquid steel"

Jun 1, 2019

By F. T. Cawood

?It is in the interest of stability and investor confidence that the healthy and necessary debate on such a (minerals) policy should soon find its way to consensus.? (President Nelson Mandela at the104th (1995), AGM of the South African Chamber of Mines) Inauguration of the new political dispensation in South Africa initiated a dynamic period in the historical development of its minerals policy. The process of substituting the current South African mineral policy framework with an acceptable ?post apartheid? system, started soon after the 1994 election of the African National Congress (ANC) government. The Green Paper on a Minerals and Mining Policy for South Africa released for public discussion in February 1998, calls for radical transformation in mineral rights ownership. A shift towards exclusive state ownership of mineral rights, away from the present dual system of private and state ownership, is the most significant proposal. The current holders of mineral rights, or their nominees, who lawfully enjoyed security of tenure under past and present mineral laws are opposed to this transformation because mineral rights were often acquired at considerable cost. The situation is compounded by poor public record-keeping and passive mineral rights administration over a very long period. This paper represents a summary of the historical developments leading to the current legislative environment and forms the basis for any discussion on which future sculpturing of South Africa?s policy regarding mineral rights can take place. One cannot plan for the future without considering the past!

Jan 1, 1998

Sandsloot open pit is situated on the northern limb of the Bushveld Complex, 250 km north east of Johannesburg, South Africa. Sandsloot is currently the largest open pit platinum mine in the world and is one of six potential open pits in the area. The geotechnical strength properties of the Platreef have posed significant mining and processing challenges to the PPRust operation since inception in 1992. In order to optimize the whole business as opposed to isolated cost centres a mine to mill initiative was embarked upon in 1997. Initial work focused on ore characterization and an entire suite of data was collected for each rock type. This included mineralogy, geochemistry, geotechnical, blast ability indices, as well as metallurgical strength data. The second phase involved the clear definition of customer requirements, namely the optimum performance criteria for the plant and mining departments. This involved extensive field trials and data capture to measure the interaction and influence of the mine to mill value chain. Once the design targets were defined, a 3D geotechnical model was constructed to ensure that the targets were consistently achieved. The model is very similar to an ore reserve model; however, it is populated with geotechnical, metallurgical and blast index data. Through software queries the appropriate blast powder factor for each mining block can be obtained, thereby ensuring the correct fragmentation is blasted for the plant and mining operation. The initiative has delivered significant results showing improvements across the mine to mill value chain. These include increased loading rates, reduced electricity and crushing consumables, as well as higher plant throughput. Additionally, the initiative has benefited both brownfield and greenfield projects on the PPRust operation

Jan 1, 2006

By C. D. K. Gauert

High-pressure waterjet technology is proposed as an alternative tool for selective underground mining of high-grade ore sections in stratiform orebodies showing a preferred ?bottom? or ?top? enrichment such as the Witwatersrand reefs and the Bushveld Complex platiniferous reefs. This technique, utilizing known mining technology together with more advanced machinery and additives as used in industrial and cleaning applications, may lead to an increased life-of-mine (LOM) for mining operations. A series of experiments was successfully carried out in a laboratory on Witwatersrand quartzite material, indicating acceptable cutting performance. Mining volumes by selectively cutting of reef portions are considered to be comparable to traditional drilling and blasting. Economic advantages of waterjet mining include energy savings due to the lower quantity of gangue rock to be hoisted to surface, as well as savings by a decrease in the usage of blasting materials. Capital expenditure of waterjet cutting, if applied on a broad scale, could be lower in the long term than that of conventional drilling and blasting methods. Mining by the application of high-pressure waterjet technology could become a competitive ?green technology? improving the economics and safety of labour-intensive mining operations. This paper suggests that waterjet cutting at an industrial scale can become a routine hard-rock mining technique in the future. Keywords waterjet cutting, high pressure, mechanized narrow reef mining, abrasive agents, costs, selective mining.

Jan 1, 2013

By V. B. Teffo

The aim of the project was to experimentally determine the coefficient of restitution, and static and rolling friction of Eskom-grade coal for discrete element modelling (DEM). These parameters will be used in further DEM studies to simulate the flow and behaviour of coal during conveyance. For the simulation to yield realistic results, the parameters for the different coal shapes identified in the samples were determined. DEM uses spherical particles, and it was found that the difference between the DEM default parameters and those measured is significantly different, by as much as 97%, which illustrates the importance of experimentally determining these parameters. The spherical particles in DEM can be used to construct the various coal shapes identified, and the parameters measured can be used to simulate realistic results. The conveyance system can then be optimized accordingly.

Jan 1, 2013