Search Documents

By D. Rankin, H. J. Stucke, W. K. B. Loftus

SYNOPSIS Planning for the Finsch opencast mine is described with particular reference to the proposed stages of mining, the method used to determine the limits of surface waste rock stripping and the derivation of the waste rock mining rate. Actual mining practice is described and the possibility of installing a skipway into the open mine at a later date is discussed. In addition, the waste dumping policy is referred to: this includes the cutting of slots through the hill on the west side of the pipe to increase tramming speeds. The crushing, washing and recovery sections of the treatment plant are described together with the various changes being made to the circuit. The most important of these are the installation of X-ray sorters for the final recovery of + 7 mesh diamonds, and the vibrating grease belt for the recovery of - 7 mesh diamonds. INTRODUCTION The Finsch Mine, a subsidiary of De Beers Consolidated Mines, Limited, is situated approximately 90 miles west of Kimberley, and some two miles from the village of Lime Acres, in the Northern Cape. Lime Acres is a company village shared with the Northern Lime Company which operates a limestone quarry and works near the township. The mine is near the southern end of a well mineralized belt producing limestone, asbestos, diamonds, manganese and iron ore, and the whole area has developed rapidly in the last 20 years. Power for mining operations is drawn from the Electricity Supply Commission. The mine is conveniently close to the main Kimberley-Postmasburg railway line. Water is drawn from the Vaal River through a 57 mile State-owned pipeline at present temporarily operated by mine staff. DISCOVERY AND PROSPECTING OPERATIONS The diamondiferous orebody is situated on the farm Brits, which is State-owned ground that has been leased to the Company for the period of mining operations. There are indications of interest in the area by prospectors (Richter, de Bruin and others) over a period of some 30 years and the discovery would possibly have been made years earlier but for a law preventing prospecting for precious stones on State-owned land. Although the pipe formed a clear depression on the hill where it was situated, it was overlain by some 5 to 40 ft of banded ironstone rubble which was washed into the depression from the hillside above the pipe and obscured the deposit. In 1958, Mr Allister Thornton Fincham applied for, and was granted, the right to prospect for base minerals on the farm Brits. Asbestos is known to occur in the area and, initially, was Mr Fincham's primary interest. However, during the prospecting operations, garnets were discovered and it was realised that diamonds might be present. In 1960, when the Precious Stones Amendment Act was passed, a company

A method is proposed for the evaluation of the influence of grout prestressing systems on the support resistance offered by timber packs. It is shown that, in order not to reduce the load-carrying capacity of timber packs, grout prestressing systems need to be at least as stiff as a single timber rise. The method was used to establish strength specifications for the grout prestressing systems to be used under non-seismic and seismic conditions. For non-seismic requirements, the 24-hour grout strength needs to be at least 1,7 MPa, and the 7-day grout strength 4,9 MPa. The investigation showed that the proposed strength specification is realistic in the light of current grout-strength capabilities. For seismic requirements, the grout strength needs to be at least 4 MPa and 8 MPa to prevent extensive damage to the grout during seismic events with a peak velocity of 1m/s 3 m/s respectively.

Jan 1, 1996

By E. J. Magri

For life-of-mine planning, as well as for short- and medium-term planning of grades and mine layouts, it is extremely important to have a clear understanding of the patterns followed by the distribution of gold and uranium within the mining area. This study is an attempt to reconcile the geostatistical approach to the determination of ore-shoot directions, via an analysis of the spatial distribution of gold and uranium values, with the sedimentological approach, which is based on the direct measurement of geological features. For the routine geostatistical estimation of ore reserves, the Hartebeestfontein gold mine was divided into 1I sections. In each of these sections, the ore-shoot directions were calculated for gold and uranium from the anisotropies disclosed by geostatistical variogram analyses. This study presents a comparison of these results with those obtained from direct geological measurements of paleo-current directions. The results suggest that geological and geostatistical studies could be of significant mutual benefit.

Jan 1, 1978

Contribution by W.D. Ortlepp In the Journal of May 1994, the authors first presented the concept and analysis that formed the basis for a design approach for deep tunnels, now expressed more explicitly in the present paper (March/April 1996). In a contribution in the Journal of March/April 1995, I expressed a certain disquiet about the validity of their original approach. The authors responded to these criticisms in the same issue. It is apparent to me now that both the contribution and its rebuttals were written, probably for different reasons, in such an obscure and pedantic way as to further confuse the reader rather than provide enlightenment. My concern still persists. But in order to avoid further confusion I will attempt to pose my uncertainties and difficulties in a much more direct way. On page 98 (top of 2nd column) in the earlier paper, an important statement concluded as follows: '. . . the horizontal ellipse requires 140 per cent less force for equivalent stability'.

Jan 1, 1996

By F. Botha, J. S. Adams, W. T. Ruhmer

The report describes the Amuran project in the Welkom area, which is being conducted by six members of the Anglo American Group. The project comprises three plants for the flotation of pyrite, a twin-stream uranium plant in which 'high-grade' slimes and pyrite can be leached separately, a pyriteburning sulphuric acid plant, and a plant for the recovery of gold from calcines. Details of these plants including capital costs and estimated production are given. Mention is made of the adsorption of gold onto activated charcoal and wet high-intensity magnetic separation as possible suitable processes for these residues.

Jan 1, 1978

By W. O. Ortlepp

This note considers the most fundamental concepts of support design for deep underground openings and discusses them briefly in the context of tabular stoping and deep hard-rock tunnelling. It concludes that the conventional re-bar, mesh, and lacing methods that have been widely used in deep gold mines are quite inappropriate for the support of highly stressed tunnels. The following is suggested as the criterion for adequate dynamic support: the energy absorbed by a support unit (yielding through some acceptable limited displacement) should exceed the kinetic energy generated by the mass of rock that is intended to be retained by that unit.

Jan 1, 1995

By I. D. Wood

The geostatistical methods given for the estimation of low-ash coal reserves take into account the geological structure of the seam, and consequently give far more reliable results than have been obtained in the past. Confidence limits are given for all the estimates.

Jan 1, 1979

By R. W. O. Kersten

This paper describes the method used at Agnes Gold Mine in the calculation of pillar strengths, which involves a back-analysis type of approach. The results obtained there are comparable with those obtained by accepted formulae for pillar strength. It was found that a stress level of 70 MPa for the width of combined pillars (Le. crown and sill pillars) causes failure of the reef drives as well as the tops and bottoms of the stope side walls. As shrinkage stoping to depths of more than 650 m would result in very low percentage extractions, alternative methods of stoping will have to be investigated for these depths.

Jan 1, 1984

By Z. Zitron, G. J. de Korte, D. W. Horsfall

This paper summarizes work carried out on the treatment of fine coal, nominally classified as minus 0,5 mm (wedge-wire screen), which is removed from the raw coal prior to the treatment of the plus 0,5 mm sizes. The minus 0,5 mm coal divides, for treatment purposes, into fines, nominally between 500 and 150 !tm, and ultrafines, nominally minus 150 !tm. Studies on processes for the treatment of minus 0,5 mm coal are discussed, and the lower size limit beneficiated is indicated for each process. The installation and operational results from a pilot froth-flotation plant treating minus 150!tm coal are described.

Jan 1, 1986

By A. L. Hinde

A review of real-time particle size analysers A. L. HINDE,. B.Sc., A.R.C.S., D.I.C., Ph.D. The physical principles of different sizing techniques are critically examined in order to evaluate the suitability of the techniques for real-time particle size assessment. Examples of both successful and unsuccessful attempts at producing an acceptable real-time sizer are described in order to delineate the difficulties involved in making rapid and accurate size measurements. Only two of the examples described have proved to be suitable for on-line particle size monitoring, namely the "MintekjRSM Onstream Slurry Sizer" manufactured by Cartner Group, Ltd., and the "PSM System 100" made by Autometrics Co. Both these commercial systems are capable of assessing particle size with an accuracy comparable with that obtained by routine sieving and weighing. The "PSM System 100" has been used successfully for automatic control of grinding circuits. Economic benefits derived from this system, operating under rigorous plant conditions for several months, have proved that real-time size analysers are of significant value to the mining and metallurgical industry.

By R. J. Gordon, N. J. Keys, N. F. Peverett

Photometric sorting of ore on a South African gold mine by N. J. KEYS. B.E. Met. (Queensland) (Visitor). R. J. GORDON. (Visitor). And N. F. PEVERETT. B.Sc. (Eng.) (Wits) (Fellow) This paper concerns the development and application of a high-throughput, multi-stream photometric sorting machine developed for the South African gold mines. It is now believed that this sorter and its progeny may be found suitable for a large proportion of all possible sorting applications. A laser-light source and sensitive photomultiplier are employed in a scanning system to detect light reflected from the surfaces of rocks passing through the sorting zone. Electronic circuitry then analyses the photomultiplier signal, which represents the varying intensity of the reflected light, and produces control signals to actuate the appropriate valves of an array of air-blast rejection devices to remove from the feed certain particles selected by the analysing process. Typical throughput per machine ranges from 50 t/h for a minus 60mm plus 30mm feed to 200 t/h for minus 150mm plus 70mm material.

Jan 9, 1974

By Ralph H. Nafziger

This paper reviews the major deposits of lower-grade chromite in the world, and a wide variety of methods used for the recovery of chromium from them. Gangue materials in more coarsely sized ores can be separated by gravity means, whereas flotation techniques are required for finer-grained materials. However, unless there is considerable Iron In the ores, physical means cannot increase the Cr/Fe ratios. Chemical techniques such as hydrometallurgical methods, chlorination, roasting and leaching, and smelting are required for this purpose. A greater understanding of the physical properties of chromites and the chemical reactions that take place in the recovery operations is required before. the recoveries from lower-grade chromites can be maximized. More efficient recovery operations can be realized If It can be shown definitively that the reduction of chromites occurs via either a gas-solld or solid-solid mechanism, for example. The effects of specific impurities on the chromite reduction reactions need to be better understood, as do reagent and pH control in the flotation of chromite.

Jan 1, 1982

Proceedings of the Ninth International Symposium on Techniques for Decision-Making in the Mineral Industry, Montreal, June 1970. The Ninth International Symposium on Techniques for Decision-Making in the Mineral Industry was sponsored by The Canadian Institute of Mining and Metallurgy, McGill University and Ecole Poly technique. The programme included 71 papers on various topics, as follows: Market Analysis and Logistics Planning; Quantification of Geological Variables; Blending; Capital Investment Decisions; Mining; Financial and Economic Analysis; Search for Mineral Deposits; Market Forecasting and Strategies; Operations Research in Process Modelling; Ore Reserve Estimation; Management Information Systems; Optimization and Control of Mineral Processes. In addition to general sessions, a special feature of the Symposium was Executives' Day, which was held to provide top and middle management with a broad understanding of the usefulness of decision-making techniques and their role in the mining organization. Panel Discussions and two keynote speakers provided a review, in non-technical terms, of the areas in which decision-making techniques have proven valuable. The present volume contains 65 papers submitted for publication, along with a complete account of the Executives' Day discussion. It is broadly divided according to the above subject headings. Approximately 550 pages, illustrated. Price: $15.00; $12.00 to students, plus 50 cents for handling costs. Order now from CIM headquarters: Canadian Institute of Mining and Metallurgy, 906-1117 Ste. Catherine St. W. Montreal 110, Quebec.

By L. A. Vermeulen, D. D. Howat

The use of pebbles as the medium in the grinding of quartz gravel in a laboratory mil provided experimental data that were used to quantify the relationships between the feed rate of ore to the mil, the fineness of grind of the product, and the wear rate and consumption of the grinding medium. Fineness of grind is expressed as the inverse of the harmonic mean size, a quantity that is calculated from data obtained by sieve analyses. The commonly used criterion for fineness of grind (the percentage of material smaller than 75 µm in the mil product) is shown to corelate approximately linearly with the inverse of the harmonic mean size. An increase in the feed rate was found to cause the harmonic mean size of the product to increase linearly, Le. the relationship previously found for metalic grinding media is applicable to al grinding media, irespective of shape or composition. Simple expressions for the consumption and wear rate of pebbles are derived from the experimental data, and are shown to be functions of the feed rate. The expression for wear rate is a monotonicaly increasing function, while that for consumption is a hyperbolicaly decreasing function of the feed rate. In contrast, a linear relationship was found between the rate of wear of the grinding medium and the rate production of fines. The expressions that were previously developed in relation to the use of metalic grinding media are shown to be equally applicable to pebble milling.

Jan 1, 1988

By A. N. Brown

Rock breakage by drilling and blasting is fundamental to every hard-rock mining operation. The subject was an apt choice for a mining school because many technological changes have taken place since the subject was last presented some ten years ago. However, because of the development of surface mining, it was decided that two schools should be held: one for underground mining, and the other for surface mining. The School on Underground Mining was held at the University of the Witwatersrand in February 1986.Copper 87 COPPER 87 is an international conference organized by metallurgical and academic institutions of two of the largest producers of copper in the world, Chile and Canada.

Jan 1, 1986

By M. J. Nicol, G. Cromberge, C. A. Flemming

A relatively simple rate equation for the kinetics of the absorption of gold from cyanide solutions onto activated carbon was lI5ed as the basis in the development of a model for multistage carbon-in-pulp and carbon-in-Ieach absorption circuits. The model was used in the prediction of both the steady-state and the transient behaviour of the absorption process, and the results were found to be in reasonable agreement with those observed in an extended pilot-plant campaign. A number of practical implications of the model are discussed, and an assessment is made of the economic consequences of the various process options available for the design of a carbon-in-pulp plant.

Jan 1, 1983

By O. L. Papendorf

For purposes of simplification, a case is presented for an engineer to discount cash flows in real rather than in current terms when giving evidence in a court of law. The difference between the two methods is highlighted, and a recommendation is made in the case where differential rates apply.

Jan 1, 1981

By E. F. E. Müller

In a search for suitable reductants for the electro-metallurgical industry. the Fuel Research Institute is conducting investigations Into the charring of coals and the properties of the chars produced. This paper gives a selection of the results obtained as an illustration of the work being done. The research is proceeding.

Jan 1, 1980

By C. A. Jermy, B. J. Venter

Excessive build-up of methane and water pressures was identified as the leading cause of some Q/the roof falls in a coal mine in the eastern Transvaal. In order to characterize the migration of the methane and water into and around the mined coal seam, a laboratory investigation of the permeability of the roof strata was undertaken. The aim of the investigation was to correlate changes in the fades with changes in permeability to enable the prediction of possible zones of pressure buildup. The tests were carried out on samples from borehole core that had been obtained from the roof strata as part of the mine exploration programme. Permeability measurements were then conducted under atmospheric and triaxial-stress conditions. For the tests under atmospheric conditions, a modified Ohle cell was used and, for the tests under triaxial-stress conditions, a modified Hoek cell was used. The liquid equivalent permeability?s of the different samples were obtained by use of ASTM D4525- 85, and these were then used as a basis for comparison. Facies type, i.e. grain size, was found to have an influence on the permeability but, owing to the variable nature of the sediments, a range of permeability rather than a specific permeability value was associated with each type of Jades. The measured permeability was bound to decrease with an increase in gas pressure. The liquid equivalent permeability was bound to increase with an increase in grain size for the coarser-grained Jades, and to decrease with an increase in grain size for the finer-grained types. The application of an external stress regime to the sample was bound to reduce the permeability, but the amount of the reduction depended on the type of stress. The permeability was also found to depend on the recent stress history of the sample. The authors conclude that the methods described are useful for the correlation of facies type with permeability, but that the results are sensitive to changes in locality.

Jan 1, 1994

Performance testing is often used by project owners and financiers to provide protection from, or assessment of, technical aspects of project design, procurement, construction and commissioning. The performance tests can range from comprehensive performance warranties relating to process performance and production in the case of lump sum turn key (LSTK) projects to less onerous demonstration tests for cost reimbursable contracts. This paper will discuss performance testing from both the contractor's and owner's perspectives and focuses on: ? when performance tests are required, ? what type of performance test/warranty is optimum for each type of project, and ? how project performance should be evaluated. The requirement for performance testing can be driven by the project financiers, particularly in the case of smaller resource development companies. In such cases, differentiation between owner's risk and contractor's risk can become contentious. At the other end of the spectrum, larger mining houses may choose to heavily influence the engineering and design process with the contractor supplying services on a reimbursable basis. In that case, the performance testing process is often limited to demonstration tests that validate performance for the owner's corporate governance requirements. This paper was prepared due to the lack of published benchmarking of performance testing and the resultant differences in expectations between a contractor and a project owner that often surface late in the contract negotiation process. The paper provides a checklist of requirements for both the owner and the contractor that may be used to provide `common purpose' early in the contract negotiation process.

Jan 1, 2007