Search Documents

By R. W. Fatzinger

The accident-frequency rate for placer mining in 1942 is reported as 36.923 accidents per million man-hours worked. This figure places placer-mining accident frequency slightly higher than that given for quarrying-35.7-but considerably under the 78.0 for coal mining and 56.5 for metal mining.4 Placer mining is subdivided into four types of activity: Underground, surface, dredging, and hydraulicking. It is the purpose of this paper to present and discuss safety practices in dredging and hydraulic mining; therefore, the following considerations will be limited to these two types of placer mining.

Jan 1, 1948

By John C. Edwards, Gene F. Friel

A series of liquid fuel fire experiments evaluated the comparative responses of five types of commercially available smoke detectors and a diffusion-mode carbon monoxide (CO) detector under normal and reduced airflow conditions based upon the alarm times of the detectors. These experiments were conducted in the Safety Research Coal Mine at the U.S. Bureau of Mines Pittsburgh Research Center. Two of the smoke detectors had manufacturer set alarms. For the other three smoke detectors, an alarm point was defined in terms of their background analog signal and the detector's electrical output noise under ambient conditions. A correlation was developed of the travel time of 5 ppm CO between pairs of CO detectors with the travel time calculated from entry and crosscut volumes and measured airflow. Based upon the relative performance of smoke detectors in this limited study, smoke detectors can be as effective as CO detectors for mine fire detection once identifiable alarm values are defined. Implementation of smoke detectors as part of an atmospheric mine monitoring system will improve mine safety.

Jan 1, 1996

By Joe Maher

Adequate mine roof support to insure the safety of men and equipment is essential to successful mining. It is also expensive, amounting to more than one-fifth of the total mining cost at the White Pine mine. Cost effectiveness is therefore a prime consideration in developing optimum roof support. Roof bolt length is an important cost factor. This Phase II work compared uniform four-foot length Resin Bolts with the hitherto standard alternating four-foot and six-foot Resin Bolts, aiming at more cost-effective roof bolting. The data generated under this Phase II show that there is no discernible difference in the roof support given by uniform four-foot, and by alternating four- and six-foot, Resin Bolts in the relatively difficult ground selected for a severe initial test comparison; subsequent data from less difficult ground led to the same conclusion, namely no discernible difference between four-foot and four-six foot bolting.

Jan 1, 1975

By Northcutt Ely

This volume- summarizes mining and petroleum legislation in 18 European jurisdictions. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identitication of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis; of the laws governing mines and quarries and their products; third, analysis of laws applicable to natural gas, petroleum, and related materials; and fourth, mention of laws regulating offshore operations. Where pertinent, sections dealing with historical background or administration have been added in countries where minerals are subject to control of States or Provinces, those areas are considered separately from the central government.

Jan 1, 1974

By Paul M. Price

The Mouat mine, Nye, Mont., was reopened in 1953 by the American Chrome Co. under a Defense Minerals Production Administration contract. Operations were terminated in 1961 after completion of the contract. Mining methods employed during this period are described in detail, and cost data are presented by years for 1953 through 1959. Ultramafic rocks of the Stillwater complex in Montana contain the largest domestic resource of chromite, and the Mouat mine has been the largest producer. Mine reserves were estimated in 1960 to be about 4.4 million tons containing 22.5 percent Cr203. The chromite deposits occur as a series of overlapping bands or lenses roughly paralleling the steeply dipping layers of the complex. Only two of the chromite layers have proven to be of economic importance. One layer is 2 to 1.6 feet wide; the other is 3 to 8 feet wide. Shrinkage stoping was generally used throughout the mine, but various methods of ore breaking, scope drawing, chute construction, etc., were tested to improve output and lower costs. Long-hole stoping proved to have limited use. Breasting down benches, developed outward from the center of the stope with air-leg drills, was satisfactory only in wider scopes. At the close of operations, the company had standardized the use of lightweight stopers to advance a flat back by breaking from a centrally located face. Mining costs were reduced 47 percent during 7 years of operation.

Jan 1, 1963

By William F. Keyes

Greensand, which is widely distributed in the Eastern United States, was produced in 1975 only by Inversand Co., a subsidiary of Hungerford & Terry, Inc., near Clayton, N.J. Production and sales information are not available for publication. Raw greensand produced by the company was sold for agricultural use as a soil conditioner. Processed greensand was used by manufacturers as filter media in equipment for the removal of manganese, iron and other elements from water. The University of Delaware received a grant of $17,051 from the Bureau of Mines early in 1976 to continue its studies of the effectiveness of greensand in removing metallic contaminants from waste waters.

Jan 1, 1977

By Ned Baker

Details are given of a Hydride Fuel System to provide 5 kg of HZ to fuel a Caterpillar 3304 engine previously modified to operate on hydrogen fuel and intended to power an underground mining vehicle. The Fuel System was installed onto the engine and the Engine/Fuel System tested under cold start conditions and a full range of engine loads and speeds. Refueling tests were also performed. The fuel system tested will support full engine power and allow delivery of at least 3/4-power on a continuous basis, from cold start conditions.

Jan 1, 1983

By E. K. Stanek

This research study was performed on a case study basis and can be divided into two parallel thrusts: electrical and thermal energy conservation. Energy consumed annually in mining and refining operations represents about 6% of the 80 quadrillion Btu's consumed nationally. In the electrical portion of the study, five areas were addressed: optimal dispatching of on-site generation, high-efficiency motors, conductor selection, power factor correction, and high efficacy lighting. In the case study mine which has a multiple unit on-site generation system, optimally dispatching units can save significant energy. The other four methods are difficult to justify on a retrofit basis due to capital costs. In the thermal portion of the study, a thermodynamic analysis was performed on the reverberatory smelting process possible areas of energy conservation were identified as radiation and convection heat losses from the furnace arch and the dumping of high energy content smelting slag. It has been shown that materials currently available can provide the means of reducing heat loss from the reverberatory furnace. It has also been shown that a significant amount of energy may be recovered from the slag. However, these are both subject to further study and validation.

Jan 1, 1982

More than 400 academic, Government, and industry representatives attended the third symposium on ash utilization and technology held in Pittsburgh, Pa., March 13-14, 1973. Sponsored by the American Public Power Association, Edison Electric Institute, National Coal Association, National Ash Association, and Bureau of Mines, the symposium Featured 26 formal presentations by leading experts from Europe and the United States on all major phases of ash production, utilization, and research. Abstracts of all the papers are grouped right after this introduction, and the full symposium proceedings follow. Sponsoring organizations and their chief representatives were the National Coal Association, James R. Garvey, Bituminous Coal Research, Inc.; Edison Electric Institute, C. E. Brackett, Southern Electric Generating Co.; American Public Power Association, Herbert Blinder, Columbus (Ohio) Electricity Division; National Ash Association, Inc., James N. Covey, Rochester Gas and Electric Corp.; and the United States Department of the Interior, Bureau of Mines, William L. Crentz.

Jan 1, 1974

By Sam S. Taylor

Disposal of brines produced with crude petroleum and natural gas is a continually increasing problem. The necessity for studying this problem has been realized more generally in recent years, and in August 1934 an agreement was made between the Kansas State Board of Health and the United States Bureau of Mines to conduct a cooperative technical study of methods of brine disposal. To date one paper in the technical press4/ and three reports5/6/ have been published in which are given results of studies carried on under this cooperative agreement. In the Mid-Continent fields, the methods used most generally for handling oil-field brines are: (1) Impounding in evaporation ponds; (2) controlled diversion into surface streams; and (3) injection into subsurface formations through wells assigned for this purpose. Various States recognize one or more of the methods as legally authorized procedure. Impounding brine in ponds and solar evaporation have proved inadequate as a general rule, owing, usually, to the porous nature of the soil, the low rate of evaporation, or both. Diversion, of

Jan 1, 1937

By Sam S. Taylor

Disposal of brines produced with crude petroleum and natural gas is a continually increasing problem. The necessity for studying this problem has been realized more generally in recent years, and in August 1934 an agreement was made between the Kansas State Board of Health and the United States Bureau of Mines to conduct a cooperative technical study of methods of brine disposal. To date one paper in the technical press4/ and three reports5/6/ 7/ have been published in which are given results of studies carried on under this cooperative agreement. In the Mid-Continent fields, the methods used most generally for handling oil-field brines are: (1) Impounding in evaporation ponds; (2) controlled diversion into surface streams; and (3) injection into subsurface formations through wells assigned for this purpose. Various States recognize one or more of the methods as legally authorized procedure. Impounding brine in ponds and solar evaporation have proved inadequate as a general rule, owing, usually, to the porous nature of the soil, the low rate of evaporation, or both. Diversion of

Jan 1, 1937

By Anderson Dana

THIS PAPER describing methods and costs of mining and preparing gravel and sand for market at the Port Jefferson plant of the Seaboard Sand and Gravel Corporation, is one of a series of articles on gravel and sand mining, prepared for and published by the U. S. Bureau of Mines, which is designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs, It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical [ ]

Jan 1, 1932

By J. A. Herbst

During the last decade it has been established that conventional flotation control strategies based on classical control theory result in significant increases in grade, recovery, and operating-cost savings. In the current report a description of an advanced model-based control philosophy is presented. The derivation and verification of a simplified flotation model is described. The implementation of a Kalman filter for estimation of unmeasured variables for input to controllers is discussed. Several control strategies using the model-based approach are described, emphasizing the nonlinear nature of the flotation plant. Expected trends in the implementation of such model-based flotation control strategies in the future are discussed.

Jan 1, 1986

By Robert B. Worthington

This investigation was undertaken to develop a more efficient copper smelting practice that would help meet the increasingly stringent antipollution standards. Continuous smelting to copper and a 0.8-to 5-percent copper slag using pure oxygen has been demonstrated for several hours at a time in a unique double furnace, which was devised to overcome the heat losses inherent in a laboratory furnace. The use of pure oxygen to effect the smelting and conversion of copper sulfide concentrate in a single unit to produce blister copper and a very high S02 concentration provides a much reduced gas volume for more economical and thorough sulfur recovery. Although the process was successfully demonstrated for several hours at a time, extended test work using longer runs will be required to balance the system and to obtain test data for adequately demonstrating its technical feasibility.

Jan 1, 1973

By George S. Rice

In 1911 the Director of the United States Bureau of Mines instructed the chief mining engineer of the bureau , during an investigation of coal-mine safety conditions in Europe, to ask the directors of the various mine-experiment stations whether they would favor a European conference . The majority of the officials in immediate charge of experiment stations favored the plan , and Victor Watteyne, inspector general of Belgium, suggested that the United States call such a conference to be held immediately after the Eighth International Congress of Applied Chemistry, which was to assemble in New York on September 3, 1912 . Accordingly, invitations were issued by the United States Government to those countries having mine-experiment stations , namely, Austria-Hungary, Belgium, France, Germany , and Great Britain, and to those that contemplated the establishment of such stations , Canada and Mexico . All but Great Britain and Canada accepted ; Mexico designated a representative , who later found it impossible to come. The Government of Great Britain in declining, expressed regret at its inability to accept ; an informal statement was made that the opening of the experimental gallery at Eskmeals , England , occupied the attention of the officials in charge . Delegates were appointed by their respective Governments as follows: Austria-Hungary, Julian Czaplinski , royal mining engineer. Belgium, Victor Watteyne , inspector general of mines . France, J. Taffanel, director of the Lievin experiment station . Germany, Carl Beyling, bergassessor, director of Dortmund experiment station. United States , Charles E. Munroe, consulting explosives expert and George S. Rice, chief mining engineer of the Bureau of Mines . Subsequently Mr. William O'Connor , a mining engineer and mine operator of Wales , who opportunely appeared at the Pittsburgh station with letters of introduction from the South Wales Institute of Engineers and from prominent mining officials of Great Britain , was unanimously invited to take part in the meeting as an unofficial representative of Great Britain . Messrs . Beyling, Taffanel , and Watteyne were met in New York on September 3, by George S. Rice, who accompanied them to Washington, where they were welcomed by Director J. A. Holmes , of the Bureau of Mines , and where , with the delegates to the Eighth International Congress of Applied Chemistry , they were presented to President Taft . Mr. Taffanel was unfortunately called back to France just before the scheduled time of the conference on account of a mine disaster ; the other delegates , including Mr. Czaplinski , convened at Pittsburgh on the morning of September 14. Mr. Rice, representing the Director of the Bureau of Mines , acted as temporary chairman , and called the meeting to order.

Jan 1, 1914

By Kenneth Eilerts

[The development and operation of ?combination on wells?5/ have created new and unusual problems, many of which cast to solved only if information is available concerning the properties of the fluids produced. Data as to the characteristics of the fluids at the relatively high pressures that exist in the reservoirs are especially important, and there is growing economic concern to know what part, if any, of the liquid recovered at the surface was liquid in the reservoir, As an extension of this problem, it is important to Know whether liquid will be formed in the reservoir it as a result o a isothermal retrograde condensation when the reservoir pressure is reduced. The pressure range of such condensation, if it occurs, is significant in the design of gas-recycling plants for maintaining reservoir pressures. In connection with the operation of such plants, it is particularly important to know how gyres sure and temperature will affect the yield of the liquid phase and the composition of the gas to be returned to the reservoir. It has not been possible to predict the behavior of these fluids that have high ratios of gas to liquid by comparing them with the behavior of low gas-liquid ratio fluids at identical pressures and temperatures. Such comparison fails because the proportions in which a component will be distributed between the phases of a system at any given temperature and pressure depend increasingly on the composition of the mixture as the critical temperature and pressure of the oysters are approached. Because many combination wells are producing from reservoirs that have temperatures near the critical point, experimental date on the properties of the fluids under reservoir conditions are particularly important at this time. To rest the immediate requirements of the industry for such experimental information an equilibrium cell has been constructed at the Petroleum Experiment Station of the Bureau of Mines, Bartlesville, Okla. When adequate experimental date, have boon accumulated, it may be possible to mare dependable estimates of the phase relations ft. high gas-liquid ratio fluids at the pre runes and temperatures characteristics of ?combination-well? reservoirs.]

Jan 1, 1940

By Galen G. Waddell

This report describes a method of measuring and analyzing the initial deformation which occurs in the medium surrounding a mine accessway as the opening is created. Discussed are (1) the hypothesis upon which the research is based; (2) the in situ rock-deformation measuring equipment developed; (3) the field tests, consisting of measuring the deformation of the medium around two 4-foot-diameter raise bores as the boring progressed; and (4) a finite-element technique to correlate theoretical with experimental results, using elastic theory. Described also are the raise-bore operation and performance. The instrumentation developed proved to have the sensitivity and resolution necessary to measure rock deformation around a full-scale raise bore during excavation. Tests show the relationships of rock deformation to progress of the raise boring and to time. The initial deformation of the opening appeared to be elastic. Using the deformation records and an estimated field stress, the modulus of elasticity was determined for the rock mass. In addition, the importance of this type of measurement in assessing support-problem areas is discussed.

Jan 1, 1971

By W. M. Dressel

This Bureau of Mines report describes a shaft closure demonstration project in which 11 inverted pyramid-shaped plugs were used to plug abandoned open mine shafts in Galena, KS, The inverted pyramid-shaped forms, fabricated from steelplate, were designed so that the inverted base would be larger, by 4 ft on a side, than the approximate size of the shaft opening at the surface residuum-solid rock interface. After the surface openings of the shafts were trimmed with a backhoe, the steel forms, complete with reinforcing, were lowered into the openings and filled with concrete; the remaining portions of the openings above the plugs were backfilled to slightly above the surrounding surface level with waste rock and soil. Location and elevation monuments were installed for long-tern evaluation of the success of the project.

Jan 1, 1985

By Anthony T. Xannacchione, Luis E. Vallejo

At present, there is little knowledge concerning the shear strength of clays containing floating rock particles with concentrations from 0 to 30%. In practice, the effect of rock particles is typically disregarded in shear strength analysis The two primary reasons for this are: 1) a lack of agreement concerning the influence of rock particles on material strength, and 2) the expense and difficulty of testing day-rack mixtures with existing laboratory procedures. These factors have impeded the development of successful slope remediation design techniques far colluviums derived from resistant sedimentary rocks or spoil produced from surface mining. This study reviewed 3 1 technical papers which contain analysis of shear strengths for clay and sands with varying mixtures of rock particles. These technical papers, published over the last 40 years, are comprised of field case studies, laboratory evaluations, and theoretical analysis. Evaluation of this body of knowledge ha shown that the shear strength gradually increases with increasing percentages of floating particles in unsaturated clays.

By M. J. Beus, B. Stewart, S. Iverson

Synopsis U.S. Mine Safety and Health Administration (MSHA) accidents statistics have identified ore-pass hazards as a significant safety problem in U.S. underground metal mines. The statistics show that nearly 75% of injuries are directly or indirectly related to pulling or freeing of ore-pass chutes, the use of hand tools in ore passes, fails of broken rock in ore passes and structural failures of chutes or gates and ore-pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines. Risk assessment methods, such as fault-tree analysis, have been employed to identify the most probable causes of orepass failures, define research priorities and analyse the factors that result in malfunctioning and unsafe ore passes. Static and dynamic loads are being measured in a laboratory setting with the use of a reduced-scale orepass mock-up. Field tests are being initiated in mine ore passes to determine static and dynamic loads. Data from the test ore passes are being compared with data from the mine to characterize true system behaviour. Computer modelling with the use of closed-form solutions, finite-element analyses and a newly developed particle flow code predicts static and dynamic leads from the flow and the impact of ore and waste in the ore pass. Preliminary results indicate that dynamic impacts from ore and waste rock might be considerably greater than expected. The total static load is substantially less than is typically used fur the structural design of chute and gate support members. It is suggested that damping factors, normal and shear stiffness and mass frictional characteristics have a significant effect on particle flow and resulting impact loads. This is being verified with the use of results from laboratory tests, field tests and particle flow analyses. Ore passes are vertical or steeply inclined openings in a rock mass through which ore and waste are transported and where they mar also be stored. A typical underground mining system is shown in Fig. 1. The arrows indicate the locations of ore passes and loading pockets and their relative configurations. The control of material flow is potentially one of the most hazardous operations in underground mining. According to MSHA data. most of the ore pass-related accidents in the U.S.A. are associated with the loading-unloading cycle and removal of blockages from ore passes. In particular, attempts to free ore hang-ups have resulted in multiple fatalities. The hazards are obvious; there is uncertainty as to when the ore will break loose and miners are unable to escape falling rock to a safe location. Although ore passes and chutes and gate systems for underground metal and non-metal mines roust meet the requirements specified in the U.S. Code of Federal Regulations (CFR). Parts 57 and 75, recent structural failures of ore-pass linings and gates have underlined the lack of adequate ore-pass design standards available to both MSHA enforcement staff and mine engineers. Because of the importance of an ore pass to the safe operation of a mine design criteria need to be assessed and new guidelines developed. Researchers at the Spokane Research Laboratory of the Nationals Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines and studying design criteria for ore passes. The near-term goal is to conduct laboratory and field experiments and computer modelling to evaluate the ore-pass design criteria currently used. Literature searches, field site